Implement FP exception register #1 (lower 32-bits of 64-bit fr[0]).
A proper implementation is necessary to allow the Linux kernel in
system mode and the qemu linux-user to send proper si_code values
on SIGFPE signal.
Always set the T-bit on taken exception, and merge over- and underflow
in system mode to just set overflow bit to mimic the behaviour I tested
on a physical machine.
The test program below can be used to verify correct behaviour. Note
that behaviour on SIGFPE may vary on different platforms. The program
should always detect the correct signal, but it may or may not be able
to sucessfully continue afterwards.
#define _GNU_SOURCE
#include <signal.h>
#include <stdio.h>
#include <fenv.h>
#include <float.h>
static void fpe_func(int sig, siginfo_t *i, void *v) {
sigset_t set;
sigemptyset(&set);
sigaddset(&set, SIGFPE);
sigprocmask(SIG_UNBLOCK, &set, NULL);
printf("GOT signal %d with si_code %ld\n", sig, i->si_code);
}
int main(int argc, char *argv[]) {
struct sigaction action = {
.sa_sigaction = fpe_func,
.sa_flags = SA_RESTART|SA_SIGINFO };
sigaction(SIGFPE, &action, 0);
feenableexcept(FE_OVERFLOW | FE_UNDERFLOW);
double x = DBL_MIN;
return printf("%lf\n", argc > 1
? 1.7976931348623158E308*1.7976931348623158E308
: x / 10);
}
Signed-off-by: Helge Deller <deller@gmx.de>
(cherry picked from commit ebd394948d)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Improve the linux-user emulation to send the correct si_code depending
on overflow (TARGET_FPE_FLTOVF), underflow (TARGET_FPE_FLTUND), ...
Note that the hardware stores the relevant flags in FP exception
register #1, which is actually the lower 32-bits of the 64-bit fr[0]
register in qemu.
Signed-off-by: Helge Deller <deller@gmx.de>
(cherry picked from commit b4b49cf39d)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
The hardware stores the instruction code in the lower bits of the FP
exception register #1 on FP assist traps.
This fixes the FP exception handler on Linux, as the Linux kernel uses
the value to decide on the correct signal which should be pushed into
userspace (see decode_fpu() in Linux kernel).
Signed-off-by: Helge Deller <deller@gmx.de>
(cherry picked from commit 923976dfe3)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
With commit 82137e6c8c ("migration: enforce multifd and postcopy preempt to
be set before incoming"), and if postcopy preempt / multifd is enabled, one
cannot setup any capability because these checks would always fail.
(qemu) migrate_set_capability xbzrle off
Error: Postcopy preempt must be set before incoming starts
To fix it, check existing cap and only raise an error if the specific cap
changed.
Fixes: 82137e6c8c ("migration: enforce multifd and postcopy preempt to be set before incoming")
Reviewed-by: Dr. David Alan Gilbert <dave@treblig.org>
Reviewed-by: Juraj Marcin <jmarcin@redhat.com>
Signed-off-by: Peter Xu <peterx@redhat.com>
(cherry picked from commit 17bec9235b)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
There're 2 QMP commands: query-sgx and query-sgx-capabilities, but
their outputs are very similar and the documentation lacks clear
differentiation.
From the codes, query-sgx is used to gather guest's SGX capabilities
(including SGX related CPUIDs and EPC sections' size, in SGXInfo), and
if guest doesn't have SGX, then QEMU will report the error message.
On the other hand, query-sgx-capabilities is used to gather host's SGX
capabilities (descripted by SGXInfo as well). And if host doesn't
support SGX, then QEMU will also report the error message.
Considering that SGXInfo is already documented and both these 2 commands
have enough error messages (for the exception case in their codes).
Therefore the QAPI documentation for these two commands only needs to
emphasize that one of them applies to the guest and the other to the
host.
Fix their documentation to reflect this difference.
Reported-by: Markus Armbruster <armbru@redhat.com>
Suggested-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Zhao Liu <zhao1.liu@intel.com>
Acked-by: Markus Armbruster <armbru@redhat.com>
Link: https://lore.kernel.org/r/20250513143131.2008078-3-zhao1.liu@intel.com
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
(cherry picked from commit 7f2131c35c)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
The GT-64120 PCI controller requires special handling where:
1. Host bridge(bus 0 ,device 0) must never be byte-swapped
2. Other devices follow MByteSwap bit in GT_PCI0_CMD
The previous implementation incorrectly swapped all accesses, breaking
host bridge detection (lspci -d 11ab:4620).
Changes made:
1. Removed gt64120_update_pci_cfgdata_mapping() and moved data_mem initialization
to gt64120_realize() for cleaner setup
2. Implemented custom read/write handlers that:
- Preserve host bridge accesses (extract32(config_reg,11,13)==0)
- apply swapping only for non-bridge devices in big-endian mode
Fixes: 145e2198 ("hw/mips/gt64xxx_pci: Endian-swap using PCI_HOST_BRIDGE MemoryRegionOps")
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/2826
Signed-off-by: Rakesh Jeyasingh <rakeshjb010@gmail.com>
Tested-by: Thomas Huth <thuth@redhat.com>
Link: https://lore.kernel.org/r/20250429170354.150581-2-rakeshjb010@gmail.com
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
(cherry picked from commit e5894fd6f4)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
At this moment we're not checking if the host has support for any
specific CSR before doing get/put regs. This will cause problems if the
host KVM doesn't support it (see [1] as an example).
We'll use the same approach done with the CPU extensions: read all known
KVM CSRs during init() to check for availability, then read/write them
if they are present. This will be made by either using get-reglist or by
directly reading the CSRs.
For now we'll just convert the CSRs to use a kvm_csr_cfg[] array,
reusing the same KVMCPUConfig abstraction we use for extensions, and use
the array in (get|put)_csr_regs() instead of manually listing them. A
lot of boilerplate will be added but at least we'll automate the get/put
procedure for CSRs, i.e. adding a new CSR in the future will be a matter
of adding it in kvm_csr_regs[] and everything else will be taken care
of.
Despite all the code changes no behavioral change is made.
[1] https://lore.kernel.org/qemu-riscv/CABJz62OfUDHYkQ0T3rGHStQprf1c7_E0qBLbLKhfv=+jb0SYAw@mail.gmail.com/
Signed-off-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Acked-by: Alistair Francis <alistair.francis@wdc.com>
Message-ID: <20250429124421.223883-6-dbarboza@ventanamicro.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Cc: qemu-stable@nongnu.org
(cherry picked from commit d3b6f1742c)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
We need the reg_id_ulong() helper to be a macro to be able to create a
static array of KVMCPUConfig that will hold CSR information.
Despite the amount of changes all of them are tedious/trivial:
- replace instances of "kvm_riscv_reg_id_ulong" with
"KVM_RISCV_REG_ID_ULONG";
- RISCV_CORE_REG(), RISCV_CSR_REG(), RISCV_CONFIG_REG() and
RISCV_VECTOR_CSR_REG() only receives one 'name' arg. Remove unneeded
'env' variables when applicable.
Signed-off-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-ID: <20250429124421.223883-5-dbarboza@ventanamicro.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Cc: qemu-stable@nongnu.org
(cherry picked from commit 11766e1761)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
This change is motivated by a future change w.r.t CSRs management. We
want to handle them the same way as KVM extensions, i.e. a static array
with KVMCPUConfig objs that will be read/write during init and so on.
But to do that properly we must be able to declare a static array that
hold KVM regs.
C does not allow to init static arrays and use functions as
initializers, e.g. we can't do:
.kvm_reg_id = kvm_riscv_reg_id_ulong(...)
When instantiating the array. We can do that with macros though, so our
goal is turn kvm_riscv_reg_ulong() in a macro. It is cleaner to turn
every other reg_id_*() function in macros, and ulong will end up using
the macros for u32 and u64, so we'll start with them.
Signed-off-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-ID: <20250429124421.223883-4-dbarboza@ventanamicro.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Cc: qemu-stable@nongnu.org
(cherry picked from commit b609610349)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
The j pseudoinstruction maps to a JAL instruction, which can only handle
a jump to somewhere with a signed 20-bit destination. In case of static
linking and LTO'ing this easily leads to "relocation truncated to fit"
error.
Switch to use tail pseudoinstruction, which is the standard way to
tail-call a function in medium code model (emits AUIPC+JALR).
Signed-off-by: Icenowy Zheng <uwu@icenowy.me>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-ID: <20250417072206.364008-1-uwu@icenowy.me>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Cc: qemu-stable@nongnu.org
(cherry picked from commit 22b448ccc6)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
On big endian systems, pte and updated_pte hold big endian host data
while pte_pa points to little endian target data. This means the branch
at cpu_helper.c:1669 will be always satisfied and restart translation,
causing an endless translation loop.
The correctness of this patch can be deduced by:
old_pte will hold value either from cpu_to_le32/64(pte) or
cpu_to_le32/64(updated_pte), both of wich is litte endian. After that,
an in-place conversion by le32/64_to_cpu(old_pte) ensures that old_pte
now is in native endian, same with pte. Therefore, the endianness of the
both side of if (old_pte != pte) is correct.
Signed-off-by: Ziqiao Kong <ziqiaokong@gmail.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-ID: <20250415080254.3667878-2-ziqiaokong@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Cc: qemu-stable@nongnu.org
(cherry picked from commit ad63158bdb)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
virtio-net expects set_features() will be called when the feature set
used by the guest changes to update the number of virtqueues but it is
not called during reset, which will clear all features, leaving the
queues added for VIRTIO_NET_F_MQ or VIRTIO_NET_F_RSS. Not only these
extra queues are visible to the guest, they will cause segmentation
fault during migration.
Call set_features() during reset to remove those queues for virtio-net
as we call set_status(). It will also prevent similar bugs for
virtio-net and other devices in the future.
Fixes: f9d6dbf0bf ("virtio-net: remove virtio queues if the guest doesn't support multiqueue")
Buglink: https://issues.redhat.com/browse/RHEL-73842
Cc: qemu-stable@nongnu.org
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Message-Id: <20250421-reset-v2-1-e4c1ead88ea1@daynix.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
(cherry picked from commit 0caed25cd1)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
ASAN spotted a leaking string in machine_set_loadparm():
Direct leak of 9 byte(s) in 1 object(s) allocated from:
#0 0x560ffb5bb379 in malloc ../projects/compiler-rt/lib/asan/asan_malloc_linux.cpp:69:3
#1 0x7f1aca926518 in g_malloc ../glib/gmem.c:106
#2 0x7f1aca94113e in g_strdup ../glib/gstrfuncs.c:364
#3 0x560ffc8afbf9 in qobject_input_type_str ../qapi/qobject-input-visitor.c:542:12
#4 0x560ffc8a80ff in visit_type_str ../qapi/qapi-visit-core.c:349:10
#5 0x560ffbe6053a in machine_set_loadparm ../hw/s390x/s390-virtio-ccw.c:802:10
#6 0x560ffc0c5e52 in object_property_set ../qom/object.c:1450:5
#7 0x560ffc0d4175 in object_property_set_qobject ../qom/qom-qobject.c:28:10
#8 0x560ffc0c6004 in object_property_set_str ../qom/object.c:1458:15
#9 0x560ffbe2ae60 in update_machine_ipl_properties ../hw/s390x/ipl.c:569:9
#10 0x560ffbe2aa65 in s390_ipl_update_diag308 ../hw/s390x/ipl.c:594:5
#11 0x560ffbdee132 in handle_diag_308 ../target/s390x/diag.c:147:9
#12 0x560ffbebb956 in helper_diag ../target/s390x/tcg/misc_helper.c:137:9
#13 0x7f1a3c51c730 (/memfd:tcg-jit (deleted)+0x39730)
Cc: qemu-stable@nongnu.org
Signed-off-by: Fabiano Rosas <farosas@suse.de>
Message-ID: <20250509174938.25935-1-farosas@suse.de>
Fixes: 1fd396e322 ("s390x: Register TYPE_S390_CCW_MACHINE properties as class properties")
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Thomas Huth <thuth@redhat.com>
(cherry picked from commit bdf12f2a56)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
This patch fixes two different bugs in v9fs_reclaim_fd():
1. Reduce latency:
This function calls v9fs_co_close() and v9fs_co_closedir() in a loop. Each
one of the calls adds two thread hops (between main thread and a fs driver
background thread). Each thread hop adds latency, which sums up in
function's loop to a significant duration.
Reduce overall latency by open coding what v9fs_co_close() and
v9fs_co_closedir() do, executing those and the loop itself altogether in
only one background thread block, hence reducing the total amount of
thread hops to only two.
2. Fix file descriptor leak:
The existing code called v9fs_co_close() and v9fs_co_closedir() to close
file descriptors. Both functions check right at the beginning if the 9p
request was cancelled:
if (v9fs_request_cancelled(pdu)) {
return -EINTR;
}
So if client sent a 'Tflush' message, v9fs_co_close() / v9fs_co_closedir()
returned without having closed the file descriptor and v9fs_reclaim_fd()
subsequently freed the FID without its file descriptor being closed, hence
leaking those file descriptors.
This 2nd bug is fixed by this patch as well by open coding v9fs_co_close()
and v9fs_co_closedir() inside of v9fs_reclaim_fd() and not performing the
v9fs_request_cancelled(pdu) check there.
Fixes: 7a46274529 ('hw/9pfs: Add file descriptor reclaim support')
Fixes: bccacf6c79 ('hw/9pfs: Implement TFLUSH operation')
Signed-off-by: Christian Schoenebeck <qemu_oss@crudebyte.com>
Reviewed-by: Greg Kurz <groug@kaod.org>
Message-Id: <5747469d3f039c53147e850b456943a1d4b5485c.1741339452.git.qemu_oss@crudebyte.com>
(cherry picked from commit 89f7b4da76)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Even though this function is serialized to be always called from main
thread, v9fs_reclaim_fd() is dispatching the coroutine to a worker thread
in between via its v9fs_co_*() calls, hence leading to the situation where
v9fs_reclaim_fd() is effectively executed multiple times simultaniously,
which renders its LRU algorithm useless and causes high latency.
Fix this by adding a simple boolean variable to ensure this function is
only called once at a time. No synchronization needed for this boolean
variable as this function is only entered and returned on main thread.
Fixes: 7a46274529 ('hw/9pfs: Add file descriptor reclaim support')
Signed-off-by: Christian Schoenebeck <qemu_oss@crudebyte.com>
Reviewed-by: Greg Kurz <groug@kaod.org>
Message-Id: <5c622067efd66dd4ee5eca740dcf263f41db20b2.1741339452.git.qemu_oss@crudebyte.com>
(cherry picked from commit 61da38db70)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
According to the i.MX 8M Plus reference manual, the status flag
I2C_I2SR[IIF] continues to be set when an interrupt condition
occurs even when I2C interrupts are disabled (I2C_I2CR[IIEN] is
clear). However, the device model only sets the flag when I2C
interrupts are enabled which causes U-Boot to loop forever. Fix
the device model by always setting the flag and let I2C_I2CR[IIEN]
guard I2C interrupts only.
Also remove the comment in the code since it merely stated the
obvious and would be outdated now.
Cc: qemu-stable@nongnu.org
Fixes: 20d0f9cf6a ("i.MX: Add I2C controller emulator")
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Acked-by: Corey Minyard <cminyard@mvista.com>
Message-ID: <20250507124040.425773-1-shentey@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
(cherry picked from commit 54e54e594b)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
When gitlab initializes the repo checkout for a CI job, it will have
done a shallow clone with only partial history. Periodically the objects
that are omitted cause trouble with the check-patch/check-dco jobs. This
is exhibited as reporting strange errors being unable to fetch certain
objects that are known to exist.
Passing the --refetch flag to 'git fetch' causes it to not assume the
local checkout has all common objects and thus re-fetch everything that
is needed. This appears to solve the check-patch/check-dco job failures.
Signed-off-by: Daniel P. Berrangé <berrange@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Message-ID: <20250225110525.2209854-1-berrange@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
(cherry picked from commit d5d028eee3)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
STI will trigger a singlestep exception even if it has inhibit-IRQ
behavior. Do not suppress single-step for all IRQ-inhibiting
instructions, instead special case MOV SS and POP SS.
Cc: qemu-stable@nongnu.org
Fixes: f0f0136abb ("target/i386: no single-step exception after MOV or POP SS", 2024-05-25)
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
(cherry picked from commit 1e94ddc685)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Because LSS need not trigger an IRQ shadow, gen_movl_seg can't just use
the destination register to decide whether to inhibit IRQs. Add an
argument.
Cc: qemu-stable@nongnu.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
(cherry picked from commit e54ef98c8a)
(back-ported to 10.0)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
According to the i.MX 8M Plus reference manual, a GPIO pin is
configured as an output when the corresponding bit in the GDIR
register is set. The function imx_gpio_set_int_line() is intended to
be a no-op if the pin is configured as an output, returning early in
such cases. However, it inverts the condition. Fix this by
returning early when the bit is set.
cc: qemu-stable@nongnu.org
Fixes: f442728097 ("i.MX: Add GPIO device")
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Message-id: 20250501183445.2389-4-shentey@gmail.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
(cherry picked from commit eba837a31b)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
If the guest code has an ISB or SB insn inside an IT block, we
generate incorrect code which trips a TCG assertion:
qemu-system-arm: ../tcg/tcg-op.c:3343: void tcg_gen_goto_tb(unsigned int): Assertion `(tcg_ctx->goto_tb_issue_mask & (1 << idx)) == 0' failed.
This is because we call gen_goto_tb(dc, 1, ...) twice:
brcond_i32 ZF,$0x0,ne,$L1
add_i32 pc,pc,$0x4
goto_tb $0x1
exit_tb $0x73d948001b81
set_label $L1
add_i32 pc,pc,$0x4
goto_tb $0x1
exit_tb $0x73d948001b81
Both calls are in arm_tr_tb_stop(), one for the
DISAS_NEXT/DISAS_TOO_MANY handling, and one for the dc->condjump
condition-failed codepath. The DISAS_NEXT handling doesn't have this
problem because arm_post_translate_insn() does the handling of "emit
the label for the condition-failed conditional execution" and so
arm_tr_tb_stop() doesn't have dc->condjump set. But for
DISAS_TOO_MANY we don't do that.
Fix the bug by making arm_post_translate_insn() handle the
DISAS_TOO_MANY case. This only affects the SB and ISB insns when
used in Thumb mode inside an IT block: only these insns specifically
set is_jmp to TOO_MANY, and their A32 encodings are unconditional.
For the major TOO_MANY case (breaking the TB because it would cross a
page boundary) we do that check and set is_jmp to TOO_MANY only after
the call to arm_post_translate_insn(); so arm_post_translate_insn()
sees is_jmp == DISAS_NEXT, and we emit the correct code for that
situation.
With this fix we generate the somewhat more sensible set of TCG ops:
brcond_i32 ZF,$0x0,ne,$L1
set_label $L1
add_i32 pc,pc,$0x4
goto_tb $0x1
exit_tb $0x7c5434001b81
(NB: the TCG optimizer doesn't optimize out the jump-to-next, but
we can't really avoid emitting it because we don't know at the
point we're emitting the handling for the condexec check whether
this insn is going to happen to be a nop for us or not.)
Cc: qemu-stable@nongnu.org
Fixes: https://gitlab.com/qemu-project/qemu/-/issues/2942
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20250501125544.727038-1-peter.maydell@linaro.org
(cherry picked from commit 8ed7c0b648)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
The use of gnu_source_prefix in the detection of getcpu() was
ineffective because the header file that declares getcpu() when
_GNU_SOURCE is defined was not included. Pass sched.h to
has_header_symbol() so that the existence of the declaration will be
properly checked.
Cc: qemu-stable@nongnu.org
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Tested-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-ID: <20250424-buildsys-v1-1-97655e3b25d7@daynix.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
(cherry picked from commit 563cd698df)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Fix a wrong conversion to gen_op_addr_addi(). The framesize should be
added like it was done before.
This bug broke booting OpenWrt MIPS32 BE malta Linux system images
generated by OpenWrt.
Cc: qemu-stable@nongnu.org
Fixes: d0b24b7f50 ("target/mips: Use gen_op_addr_addi() when possible")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-ID: <20250412194003.181411-1-hauke@hauke-m.de>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
(cherry picked from commit d4a785ba30)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
The documentation for the CPUClass::gdb_arch_name method claims that
the returned string should be freed with g_free(). This is not
correct: in commit a650683871 we changed this method to
instead return a simple constant string, but forgot to update
the documentation.
Make the documentation match the new semantics.
Fixes: a650683871 ("hw/core/cpu: Return static value with gdb_arch_name()")
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-ID: <20250317142819.900029-2-peter.maydell@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
(cherry picked from commit 56a9f0d4c4)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
The comment about not being able to define a field with
zero bits is out of date since 94597b6146
("decodetree: Allow !function with no input bits").
This fixes the missing load of imm in the disassembler.
Cc: qemu-stable@nongnu.org
Fixes: 9d8caa67a2 ("target/avr: Add support for disassembling via option '-d in_asm'")
Reviewed-by: Pierrick Bouvier <pierrick.bouvier@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
(cherry picked from commit 6b661b7ed7)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
In msys2 distribution objdump from gcc is using single tab character
prefix, but objdump from clang is using 4 white space characters instead.
The script will not identify any dll dependencies for a QEMU build
generated with clang. This in turn will fail the build, because there
will be no files inside dlldir and no setup file will be created.
Instead of checking for whitespace in prefix use lstrip to accommodate
for differences in outputs.
Signed-off-by: Arthur Sengileyev <arthur.sengileyev@gmail.com>
Reviewed-by: Stefan Weil <sw@weilnetz.de>
Reviewed-by: Michael Tokarev <mjt@tls.msk.ru>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
(cherry picked from commit b0b5af62ef)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Originally, all failed SG_IO requests called scsi_handle_rw_error() to
apply the configured error policy. However, commit f3126d65, which was
supposed to be a mere refactoring for scsi-disk.c, broke this and
accidentally completed the SCSI request without considering the error
policy any more if the error was signalled in the host_status field.
Apart from the commit message not describing the change as intended,
errors indicated in host_status are also obviously backend errors and
not something the guest must deal with independently of the error
policy.
This behaviour means that some recoverable errors (such as a path error
in multipath configurations) were reported to the guest anyway, which
might not expect it and might consider its disk broken.
Make sure that we apply the error policy again for host_status errors,
too. This addresses an existing FIXME comment and allows us to remove
some comments warning that callbacks weren't always called. With this
fix, they are called in all cases again.
The return value passed to the request callback doesn't have more free
values that could be used to indicate host_status errors as well as SAM
status codes and negative errno. Store the value in the host_status
field of the SCSIRequest instead and use -ENODEV as the return value (if
a path hasn't been reachable for a while, blk_aio_ioctl() will return
-ENODEV instead of just setting host_status, so just reuse it here -
it's not necessarily entirely accurate, but it's as good as any errno).
Cc: qemu-stable@nongnu.org
Fixes: f3126d65b3 ('scsi: move host_status handling into SCSI drivers')
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Message-ID: <20250407155949.44736-1-kwolf@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Hanna Czenczek <hreitz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
(cherry picked from commit 61b6d9b749)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Commit 60d30cff84 ("target/ppc: Move SPR indirect registers into
PnvCore") was mismerged and moved the SPRs to power8-only, instead
of power9/10-only.
Fixes: 60d30cff84 ("target/ppc: Move SPR indirect registers into PnvCore")
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Cc: qemu-stable@nongnu.org
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
(cherry picked from commit b3d47c8303)
(Mjt: adjust context for v9.2.0-2634-gffb6440cc5 "ppc/pnv: Add new PowerPC Special Purpose Registers (RWMR)")
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
The per-core SCRATCH0-7 registers are shared between big cores, which
was missed in the big-core implementation. It is difficult to model
well with the big-core == 2xPnvCore scheme we moved to, this fix
uses the even PnvCore to store the scrach data.
Also remove a stray log message that came in with the same patch that
introduced patch.
Fixes: c26504afd5 ("ppc/pnv: Add a big-core mode that joins two regular cores")
Cc: qemu-stable@nongnu.org
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
(cherry picked from commit 9808ce6d5c)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Currently, the QEMU-emulated AMD IOMMU device use PCI vendor id 0x1022
(AMD) with device id zero (undefined). Eventhough this does not cause any
functional issue for AMD IOMMU driver since it normally uses information
in the ACPI IVRS table to probe and initialize the device per
recommendation in the AMD IOMMU specification, the device id zero causes
the Windows Device Manager utility to show the device as an unknown device.
Since Windows only recognizes AMD IOMMU device with device id 0x1419 as
listed in the machine.inf file, modify the QEMU AMD IOMMU model to use
the id 0x1419 to avoid the issue. This advertise the IOMMU as the AMD
IOMMU device for Family 15h (Models 10h-1fh).
Signed-off-by: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com>
Message-Id: <20250325021140.5676-1-suravee.suthikulpanit@amd.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Reviewed-by: Yan Vugenfirer <yvugenfi@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
(cherry picked from commit 719255486d)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
When update_pagemask was split from helper_mtc0_pagemask,
we failed to actually write to the new parameter but continue
to write to env->CP0_PageMask. Thus the use within
page_table_walk_refill modifies cpu state and not the local
variable as expected.
Simplify by renaming to compute_pagemask and returning the
value directly. No need for either env or pointer return.
Fixes: 074cfcb4da ("target/mips: Implement hardware page table walker for MIPS32")
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-ID: <20250328175526.368121-4-richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Cc: qemu-stable@nongnu.org
(cherry picked from commit 256ba7715b)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Revert ee3863b9d4 and a08d60bc6c. The logic behind changing
the system page size because of what the Loongson kernel "prefers"
is flawed.
In the Loongson-2E manual, section 5.5, it is clear that the cpu
supports a 4k page size (along with many others). Similarly for
the Loongson-3 series CPUs, the 4k page size is mentioned in the
section 7.7 (PageMask Register). Therefore we must continue to
support a 4k page size.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-ID: <20250328175526.368121-2-richard.henderson@linaro.org>
[PMD: Mention Loongson-3 series CPUs]
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
(cherry picked from commit fca2817fdc)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Updated the IRQ handler mask check to AND with select variable.
This ensures that the interrupt service routine is correctly triggered
for the interrupts within the same irq group.
For example, both `eth0` and the debug UART are handled in `GICINT132`.
Without this fix, the debug console may hang if the `eth0` ISR is not
handled.
Signed-off-by: Steven Lee <steven_lee@aspeedtech.com>
Change-Id: Ic3609eb72218dfd68be6057d78b8953b18828709
Reviewed-by: Cédric Le Goater <clg@redhat.com>
Fixes: d831c5fd86 ("aspeed/intc: Add AST2700 support")
Link: https://lore.kernel.org/qemu-devel/20250320092543.4040672-2-steven_lee@aspeedtech.com
Signed-off-by: Cédric Le Goater <clg@redhat.com>
(cherry picked from commit 7b8cbe5162)
(Mjt: update for before v9.2.0-2466-g5824e8bf6beb
"hw/intc/aspeed: Introduce IRQ handler function to reduce code duplication")
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
The maximum padding size is either 64 or 128 bytes and should always be smaller
than "req_len". If "padding_size" exceeds "req_len", then
"req_len - padding_size" underflows due to "uint32_t" data type, leading to a
large incorrect value (e.g., `0xFFXXXXXX`). This causes an out-of-bounds memory
access, potentially leading to a buffer overflow.
Added a check to ensure "padding_size" does not exceed "req_len" before
computing "pad_offset". This prevents "req_len - padding_size" from underflowing
and avoids accessing invalid memory.
Signed-off-by: Jamin Lin <jamin_lin@aspeedtech.com>
Reviewed-by: Cédric Le Goater <clg@redhat.com>
Fixes: 5cd7d8564a ("aspeed/hace: Support AST2600 HACE ")
Link: https://lore.kernel.org/qemu-devel/20250321092623.2097234-3-jamin_lin@aspeedtech.com
Signed-off-by: Cédric Le Goater <clg@redhat.com>
(cherry picked from commit 78877b2e06)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Recently, when I was writing a RISCV test, I found that when VL is set to 0, the
instruction should be nop, but when I tested it, I found that QEMU will treat
all elements as tail elements, and in the case of VTA=1, write all elements
to 1.
After troubleshooting, it was found that the vext_vx_rm_1 function was called in
the vext_vx_rm_2, and then the vext_set_elems_1s function was called to process
the tail element, but only VSTART >= vl was checked in the vext_vx_rm_1
function, which caused the tail element to still be processed even if it was
returned in advance.
So I've made the following change:
Put VSTART_CHECK_EARLY_EXIT(env) at the beginning of the vext_vx_rm_2 function,
so that the VSTART register is checked correctly.
Fixes: df4252b2ec ("target/riscv/vector_helpers: do early exit when
vstart >= vl")
Signed-off-by: Chao Liu <lc00631@tecorigin.com>
Reviewed-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Message-ID: <b2649f14915150be4c602d63cd3ea4adf47e9d75.1741573286.git.lc00631@tecorigin.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
(cherry picked from commit 4e9e2478df)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Some vector instructions are special, such as the vlm.v instruction,
where setting its vl actually sets evl = (vl + 7) >> 3. To improve
maintainability, we will uniformly use VSTART_CHECK_EARLY_EXIT() to
check for the condition vstart >= vl. This function will also handle
cases involving evl.
Fixes: df4252b2ec ("target/riscv/vector_helpers: do early exit when
vstart >= vl")
Signed-off-by: Chao Liu <lc00631@tecorigin.com>
Reviewed-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Message-ID: <f575979874e323a9e0da7796aa391c7d87e56f88.1741573286.git.lc00631@tecorigin.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
(cherry picked from commit e83845316a)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Facility interrupt checks in general should come after the ISA version
check, because the facility interrupt and facility type themselves are
ISA dependent and should not appear on CPUs where the instruction does
not exist at all.
This resolves a QEMU crash booting NetBSD/macppc due to
qemu: fatal: Raised an exception without defined vector 94
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/2741
Cc: Chinmay Rath <rathc@linux.ibm.com>
Cc: qemu-stable@nongnu.org
Debugged-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Fixes: aa0f34ec3f ("target/ppc: implement vrlq")
Fixes: 7419dc5b2b ("target/ppc: Move VSX vector storage access insns to decodetree.")
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
(cherry picked from commit 8defe9da08)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Clang on LoongArch only accepts fp register names in the dollar-prefixed
form, while GCC allows omitting the dollar. Change registers in ASM
clobbers to the dollar-prefixed form to make user emulators buildable
with Clang on loongarch64. No functional change invovled.
Cc: qemu-stable@nongnu.org
Fixes: adc8467e69 ("host/include/loongarch64: Add atomic16 load and store")
Signed-off-by: Yao Zi <ziyao@disroot.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Bibo Mao <maobibo@loongson.cn>
Signed-off-by: Bibo Mao <maobibo@loongson.cn>
(cherry picked from commit ca2737d6ec)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Commit f06bfe3dc3 ("target/riscv: implement zicfiss instructions") adds
`ssamoswap` instruction. `ssamoswap` takes the code-point from existing
reserved encoding (and not a zimop like other shadow stack instructions).
If shadow stack is not enabled (via xenvcfg.SSE) and effective priv is
less than M then `ssamoswap` must result in an illegal instruction
exception. However if effective priv is M, then `ssamoswap` results in
store/AMO access fault. See Section "22.2.3. Shadow Stack Memory
Protection" of priv spec.
Fixes: f06bfe3dc3 ("target/riscv: implement zicfiss instructions")
Reported-by: Ved Shanbhogue <ved@rivosinc.com>
Signed-off-by: Deepak Gupta <debug@rivosinc.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-ID: <20250306064636.452396-2-debug@rivosinc.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
(cherry picked from commit d2c5759c8d)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Commit:8205bc1 ("target/riscv: introduce ssp and enabling controls for
zicfiss") introduced CSR_SSP but it mis-interpreted the spec on access
to CSR_SSP in M-mode. Gated to CSR_SSP is not gated via `xSSE`. But
rather rules clearly specified in section "22.2.1. Shadow Stack Pointer
(ssp) CSR access contr" in the priv spec.
Fixes: 8205bc127a ("target/riscv: introduce ssp and enabling controls
for zicfiss". Thanks to Adam Zabrocki for bringing this to attention.
Reported-by: Adam Zabrocki <azabrocki@nvidia.com>
Signed-off-by: Deepak Gupta <debug@rivosinc.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-ID: <20250306064636.452396-1-debug@rivosinc.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
(cherry picked from commit 86c78b2806)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Add .set_vnet_le() function that always returns success, assuming that
vDPA h/w always implements LE data format. Otherwise, QEMU disables vDPA and
outputs the message:
"backend does not support LE vnet headers; falling back on userspace virtio"
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Eugenio Pérez <eperezma@redhat.com>
Signed-off-by: Konstantin Shkolnyy <kshk@linux.ibm.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
(cherry picked from commit b027f55a99)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
The check for fp_excp_el in assert_fp_access_checked is
incorrect. For SME, with StreamingMode enabled, the access
is really against the streaming mode vectors, and access
to the normal fp registers is allowed to be disabled.
C.f. sme_enabled_check.
Convert sve_access_checked to match, even though we don't
currently check the exception state.
Cc: qemu-stable@nongnu.org
Fixes: 3d74825f4d ("target/arm: Add SME enablement checks")
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20250307190415.982049-2-richard.henderson@linaro.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
(cherry picked from commit 298a04998f)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
On ARM hosts with CTR_EL0.DIC and CTR_EL0.IDC set, this would only cause
an ISB to be executed during cache maintenance, which could lead to QEMU
executing TBs containing garbage instructions.
This seems to be because the ISB finishes executing instructions and
flushes the pipeline, but the ISB doesn't guarantee that writes from the
executed instructions are committed. If a small enough TB is created, it's
possible that the writes setting up the TB aren't committed by the time the
TB is executed.
This function is intended to be a port of the gcc implementation
(https://github.com/gcc-mirror/gcc/blob/85b46d0795ac76bc192cb8f88b646a647acf98c1/libgcc/config/aarch64/sync-cache.c#L67)
which makes the first DSB unconditional, so we can fix the synchronization
issue by doing that as well.
Cc: qemu-stable@nongnu.org
Fixes: 664a79735e ("util: Specialize flush_idcache_range for aarch64")
Signed-off-by: Joe Komlodi <komlodi@google.com>
Message-id: 20250310203622.1827940-2-komlodi@google.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
(cherry picked from commit e6c38d2ab5)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Block drivers assume in their .bdrv_open() implementation that their
state in bs->opaque has been zeroed; it is initially allocated with
g_malloc0() in bdrv_open_driver().
bdrv_snapshot_goto() needs to make sure that it is zeroed again before
calling drv->bdrv_open() to avoid that block drivers use stale values.
One symptom of this bug is VMDK running into a double free when the user
tries to apply an internal snapshot like 'qemu-img snapshot -a test
test.vmdk'. This should be a graceful error because VMDK doesn't support
internal snapshots.
==25507== Invalid free() / delete / delete[] / realloc()
==25507== at 0x484B347: realloc (vg_replace_malloc.c:1801)
==25507== by 0x54B592A: g_realloc (gmem.c:171)
==25507== by 0x1B221D: vmdk_add_extent (../block/vmdk.c:570)
==25507== by 0x1B1084: vmdk_open_sparse (../block/vmdk.c:1059)
==25507== by 0x1AF3D8: vmdk_open (../block/vmdk.c:1371)
==25507== by 0x1A2AE0: bdrv_snapshot_goto (../block/snapshot.c:299)
==25507== by 0x205C77: img_snapshot (../qemu-img.c:3500)
==25507== by 0x58FA087: (below main) (libc_start_call_main.h:58)
==25507== Address 0x832f3e0 is 0 bytes inside a block of size 272 free'd
==25507== at 0x4846B83: free (vg_replace_malloc.c:989)
==25507== by 0x54AEAC4: g_free (gmem.c:208)
==25507== by 0x1AF629: vmdk_close (../block/vmdk.c:2889)
==25507== by 0x1A2A9C: bdrv_snapshot_goto (../block/snapshot.c:290)
==25507== by 0x205C77: img_snapshot (../qemu-img.c:3500)
==25507== by 0x58FA087: (below main) (libc_start_call_main.h:58)
This error was discovered by fuzzing qemu-img.
Cc: qemu-stable@nongnu.org
Closes: https://gitlab.com/qemu-project/qemu/-/issues/2853
Closes: https://gitlab.com/qemu-project/qemu/-/issues/2851
Reported-by: Denis Rastyogin <gerben@altlinux.org>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Message-ID: <20250310104858.28221-1-kwolf@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
(cherry picked from commit b75c5f9879)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
For accesses to the 91c111 data register, the address within the
packet's data frame is determined by a combination of the pointer
register and the offset used to access the data register, so that you
can access data at effectively wider than byte width. The pointer
register's pointer field is 11 bits wide, which is exactly the size
to index a 2048-byte data frame.
We weren't quite getting the logic right for ensuring that we end up
with a pointer value to use in the s->data[][] array that isn't out
of bounds:
* we correctly mask when getting the initial pointer value
* for the "autoincrement the pointer register" case, we
correctly mask after adding 1 so that the pointer register
wraps back around at the 2048 byte mark
* but for the non-autoincrement case where we have to add the
low 2 bits of the data register offset, we don't account
for the possibility that the pointer register is 0x7ff
and the addition should wrap
Fix this bug by factoring out the "get the p value to use as an array
index" into a function, making it use FIELD macro names rather than
hard-coded constants, and having a utility function that does "add a
value and wrap it" that we can use both for the "autoincrement" and
"add the offset bits" codepaths.
Cc: qemu-stable@nongnu.org
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/2758
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-ID: <20250228191652.1957208-1-peter.maydell@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
(cherry picked from commit 700d3d6dd4)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
When the smc91c111 transmits a packet, it must read a control byte
which is at the end of the data area and CRC. However, we don't
sanitize the length field in the packet buffer, so if the guest sets
the length field to something large we will try to read past the end
of the packet data buffer when we access the control byte.
As usual, the datasheet says nothing about the behaviour of the
hardware if the guest misprograms it in this way. It says only that
the maximum valid length is 2048 bytes. We choose to log the guest
error and silently drop the packet.
This requires us to factor out the "mark the tx packet as complete"
logic, so we can call it for this "drop packet" case as well as at
the end of the loop when we send a valid packet.
Cc: qemu-stable@nongnu.org
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/2742
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-ID: <20250228174802.1945417-3-peter.maydell@linaro.org>
[PMD: Update smc91c111_do_tx() as len > MAX_PACKET_SIZE]
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
(cherry picked from commit aad6f264ad)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
The smc91c111 uses packet numbers as an index into its internal
s->data[][] array. Valid packet numbers are between 0 and 3, but
the code does not generally check this, and there are various
places where the guest can hand us an arbitrary packet number
and cause an out-of-bounds access to the data array.
Add validation of packet numbers. The datasheet is not very
helpful about how guest errors like this should be handled:
it says nothing on the subject, and none of the documented
error conditions are relevant. We choose to log the situation
with LOG_GUEST_ERROR and silently ignore the attempted operation.
In the places where we are about to access the data[][] array
using a packet number and we know the number is valid because
we got it from somewhere that has already validated, we add
an assert() to document that belief.
Cc: qemu-stable@nongnu.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-ID: <20250228174802.1945417-2-peter.maydell@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
(cherry picked from commit 2fa3a5b946)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
The commit to fix the OCC common area sensor mappings didn't update the
register offsets to match.
Before this change, skiboot reports:
[ 0.347100086,3] OCC: Chip 0 sensor data invalid
Afterward, there is no error and the sensor_groups directory appears
under /sys/firmware/opal/.
The SLW_IMAGE_BASE address looks like a workaround to intercept firmware
memory accesses, but that does not seem to be required now (and would
have been broken by the OCC common area region mapping change anyway).
So it can be removed.
Fixes: 3a1b70b66b ("ppc/pnv: Fix OCC common area region mapping")
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
(cherry picked from commit 29c041ca7f)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Commit a0d7215e33 ("vhost-vdpa: do not cleanup the vdpa/vhost-net
structures if peer nic is present") effectively delayed the backend
cleanup, allowing the frontend or the guest to access it resources as
long as the frontend is still visible to the guest.
However it does not clean up the resources until the qemu process is
over. This causes an effective leak if the device is deleted with
device_del, as there is no way to close the vdpa device. This makes
impossible to re-add that device to this or other QEMU instances until
the first instance of QEMU is finished.
Move the cleanup from qemu_cleanup to the NIC deletion and to
net_cleanup.
Fixes: a0d7215e33 ("vhost-vdpa: do not cleanup the vdpa/vhost-net structures if peer nic is present")
Reported-by: Lei Yang <leiyang@redhat.com>
Signed-off-by: Eugenio Pérez <eperezma@redhat.com>
Signed-off-by: Jonah Palmer <jonah.palmer@oracle.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
(cherry picked from commit e7891c575f)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
This change is used in later commits so we can avoid the removal of the
netclient if it is delayed.
No functional change intended.
Reviewed-by: Si-Wei Liu <si-wei.liu@oracle.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Eugenio Pérez <eperezma@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
(cherry picked from commit db0d4017f9)
(Mjt: pick this one up for the following change,
"net: move backend cleanup to NIC cleanup")
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Currently we call icount_start_warp_timer() from timerlist_rearm().
This produces incorrect behaviour, because timerlist_rearm() is
called, for instance, when a timer callback modifies its timer. We
cannot decide here to warp the timer forwards to the next timer
deadline merely because all_cpu_threads_idle() is true, because the
timer callback we were called from (or some other callback later in
the list of callbacks being invoked) may be about to raise a CPU
interrupt and move a CPU from idle to ready.
The only valid place to choose to warp the timer forward is from the
main loop, when we know we have no outstanding IO or timer callbacks
that might be about to wake up a CPU.
For Arm guests, this bug was mostly latent until the refactoring
commit f6fc36deef ("target/arm/helper: Implement
CNTHCTL_EL2.CNT[VP]MASK"), which exposed it because it refactored a
timer callback so that it happened to call timer_mod() first and
raise the interrupt second, when it had previously raised the
interrupt first and called timer_mod() afterwards.
This call seems to have originally derived from the
pre-record-and-replay icount code, which (as of e.g. commit
db1a49726c in 2010) in this location did a call to
qemu_notify_event(), necessary to get the icount code in the vCPU
round-robin thread to stop and recalculate the icount deadline when a
timer was reprogrammed from the IO thread. In current QEMU,
everything is done on the vCPU thread when we are in icount mode, so
there's no need to try to notify another thread here.
I suspect that the other reason why this call was doing icount timer
warping is that it pre-dates commit efab87cf79 from 2015, which
added a call to icount_start_warp_timer() to main_loop_wait(). Once
the call in timerlist_rearm() has been removed, if the timer
callbacks don't cause any CPU to be woken up then we will end up
calling icount_start_warp_timer() from main_loop_wait() when the rr
main loop code calls rr_wait_io_event().
Remove the incorrect call from timerlist_rearm().
Cc: qemu-stable@nongnu.org
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/2703
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Tested-by: Alex Bennée <alex.bennee@linaro.org>
Message-id: 20250210135804.3526943-1-peter.maydell@linaro.org
(cherry picked from commit 02ae315467)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Our STRD implementation doesn't correctly implement the requirement:
* if the address is 8-aligned the access must be a 64-bit
single-copy atomic access, not two 32-bit accesses
Rewrite the handling of STRD to use a single tcg_gen_qemu_st_i64()
of a value produced by concatenating the two 32 bit source registers.
This allows us to get the atomicity right.
As with the LDRD change, now that we don't update 'addr' in the
course of performing the store we need to adjust the offset
we pass to op_addr_ri_post() and op_addr_rr_post().
Cc: qemu-stable@nongnu.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20250227142746.1698904-3-peter.maydell@linaro.org
(cherry picked from commit ee786ca115)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Our LDRD implementation is wrong in two respects:
* if the address is 4-aligned and the load crosses a page boundary
and the second load faults and the first load was to the
base register (as in cases like "ldrd r2, r3, [r2]", then we
must not update the base register before taking the fault
* if the address is 8-aligned the access must be a 64-bit
single-copy atomic access, not two 32-bit accesses
Rewrite the handling of the loads in LDRD to use a single
tcg_gen_qemu_ld_i64() and split the result into the destination
registers. This allows us to get the atomicity requirements
right, and also implicitly means that we won't update the
base register too early for the page-crossing case.
Note that because we no longer increment 'addr' by 4 in the course of
performing the LDRD we must change the adjustment value we pass to
op_addr_ri_post() and op_addr_rr_post(): it no longer needs to
subtract 4 to get the correct value to use if doing base register
writeback.
STRD has the same problem with not getting the atomicity right;
we will deal with that in the following commit.
Cc: qemu-stable@nongnu.org
Reported-by: Stu Grossman <stu.grossman@gmail.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20250227142746.1698904-2-peter.maydell@linaro.org
(cherry picked from commit cde3247651)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
When FEAT_SEL2 was implemented the SEL2 timers were missed. This
shows up when building the latest Hafnium with SPMC_AT_EL=2. The
actual implementation utilises the same logic as the rest of the
timers so all we need to do is:
- define the timers and their access functions
- conditionally add the correct system registers
- create a new accessfn as the rules are subtly different to the
existing secure timer
Fixes: e9152ee91c (target/arm: add ARMv8.4-SEL2 system registers)
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20250204125009.2281315-7-peter.maydell@linaro.org
Cc: qemu-stable@nongnu.org
Cc: Andrei Homescu <ahomescu@google.com>
Cc: Arve Hjønnevåg <arve@google.com>
Cc: Rémi Denis-Courmont <remi.denis.courmont@huawei.com>
[PMM: CP_ACCESS_TRAP_UNCATEGORIZED -> CP_ACCESS_UNDEFINED;
offset logic now in gt_{indirect,direct}_access_timer_offset() ]
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
(cherry picked from commit f9f99d7ca5)
(Mjt: CP_ACCESS_UNDEFINED -> CP_ACCESS_TRAP_UNCATEGORIZED)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
When reading or writing the timer registers, sometimes we need to
apply one of the timer offsets. Specifically, this happens for
direct reads of the counter registers CNTPCT_EL0 and CNTVCT_EL0 (and
their self-synchronized variants CNTVCTSS_EL0 and CNTPCTSS_EL0). It
also applies for direct reads and writes of the CNT*_TVAL_EL*
registers that provide the 32-bit downcounting view of each timer.
We currently do this with duplicated code in gt_tval_read() and
gt_tval_write() and a special-case in gt_virt_cnt_read() and
gt_cnt_read(). Refactor this so that we handle it all in a single
function gt_direct_access_timer_offset(), to parallel how we handle
the offset for indirect accesses.
The call in the WFIT helper previously to gt_virt_cnt_offset() is
now to gt_direct_access_timer_offset(); this is the correct
behaviour, but it's not immediately obvious that it shouldn't be
considered an indirect access, so we add an explanatory comment.
This commit should make no behavioural changes.
(Cc to stable because the following bugfix commit will
depend on this one.)
Cc: qemu-stable@nongnu.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-id: 20250204125009.2281315-6-peter.maydell@linaro.org
(cherry picked from commit 02c648a0a1)
(Mjt: context fix in target/arm/internals.h)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Currently we handle CNTV_TVAL_EL02 by calling gt_tval_read() for the
EL1 virt timer. This is almost correct, but the underlying
CNTV_TVAL_EL0 register behaves slightly differently. CNTV_TVAL_EL02
always applies the CNTVOFF_EL2 offset; CNTV_TVAL_EL0 doesn't do so if
we're at EL2 and HCR_EL2.E2H is 1.
We were getting this wrong, because we ended up in
gt_virt_cnt_offset() and did the E2H check.
Factor out the tval read/write calculation from the selection of the
offset, so that we can special case gt_virt_tval_read() and
gt_virt_tval_write() to unconditionally pass CNTVOFF_EL2.
Cc: qemu-stable@nongnu.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-id: 20250204125009.2281315-5-peter.maydell@linaro.org
(cherry picked from commit 4aecd4b442)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
When we added Secure EL2 support, we missed that this needs an update
to the access code for the EL3 physical timer registers. These are
supposed to UNDEF from Secure EL1 when Secure EL2 is enabled.
(Note for stable backporting: for backports to branches where
CP_ACCESS_UNDEFINED is not defined, the old name to use instead
is CP_ACCESS_TRAP_UNCATEGORIZED.)
Cc: qemu-stable@nongnu.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-id: 20250204125009.2281315-4-peter.maydell@linaro.org
(cherry picked from commit bdd641541f)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
When we are calculating timer deadlines, the correct definition of
whether or not to apply an offset to the physical count is described
in the Arm ARM DDI4087 rev L.a section D12.2.4.1. This is different
from when the offset should be applied for a direct read of the
counter sysreg.
We got this right for the EL1 physical timer and for the EL1 virtual
timer, but got all the rest wrong: they should be using a zero offset
always.
Factor the offset calculation out into a function that has a comment
documenting exactly which offset it is calculating and which gets the
HYP, SEC, and HYPVIRT cases right.
Cc: qemu-stable@nongnu.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-id: 20250204125009.2281315-2-peter.maydell@linaro.org
(cherry picked from commit db6c219283)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
This error was discovered by fuzzing qemu-img.
In the QED block driver, the need_check_timer timer is freed in
bdrv_qed_detach_aio_context, but the pointer to the timer is not
set to NULL. This can lead to a use-after-free scenario
in bdrv_qed_drain_begin().
The need_check_timer pointer is set to NULL after freeing the timer.
Which helps catch this condition when checking in bdrv_qed_drain_begin().
Closes: https://gitlab.com/qemu-project/qemu/-/issues/2852
Signed-off-by: Denis Rastyogin <gerben@altlinux.org>
Message-ID: <20250304083927.37681-1-gerben@altlinux.org>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
(cherry picked from commit 2ad638a3d1)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Instead of migrating the raw tick_offset, goldfish_rtc migrates a
recalculated value based on QEMU_CLOCK_VIRTUAL. As QEMU_CLOCK_VIRTUAL
stands still across a save-and-restore cycle, the guest RTC becomes out
of sync with the host RTC when the VM is restored.
As described in the bug description, it looks like this calculation was
copied from pl031 RTC, which had its tick_offset migration fixed by
Commit 032cfe6a79 ("pl031: Correctly migrate state when using -rtc
clock=host").
Migrate the tick_offset directly, adding it as a version-dependent field
to VMState. Keep the old behavior when migrating from previous versions.
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/2033
Signed-off-by: Rodrigo Dias Correa <r@drigo.nl>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-ID: <20250114212150.228241-1-r@drigo.nl>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
(cherry picked from commit 3521f9cadc)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
In the RISC-V privileged ISA section 3.1.15 table 15, it is determined
that a debug exception that is triggered from a load/store has a higher
priority than a possible fault that this access might trigger.
This is not the case ATM as shown in [1]. Adding a breakpoint in an
address that deliberately will fault is causing a load page fault
instead of a debug exception. The reason is that we're throwing in the
page fault as soon as the fault occurs (end of riscv_cpu_tlb_fill(),
raise_mmu_exception()), not allowing the installed watchpoints to
trigger.
Call cpu_check_watchpoint() in the page fault path to search and execute
any watchpoints that might exist for the address, never returning back
to the fault path. If no watchpoints are found cpu_check_watchpoint()
will return and we'll fall-through the regular path to
raise_mmu_exception().
[1] https://gitlab.com/qemu-project/qemu/-/issues/2627
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/2627
Signed-off-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-ID: <20250121170626.1992570-3-dbarboza@ventanamicro.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
(cherry picked from commit c86edc5476)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
The mcontrol select bit (19) is always zero, meaning our triggers will
always match virtual addresses. In this condition, if the user does not
specify a size for the trigger, the access size defaults to XLEN.
At this moment we're using def_size = 8 regardless of CPU XLEN. Use
def_size = 4 in case we're running 32 bits.
Fixes: 95799e36c1 ("target/riscv: Add initial support for the Sdtrig extension")
Signed-off-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-ID: <20250121170626.1992570-2-dbarboza@ventanamicro.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
(cherry picked from commit 3fba76e61c)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
In prop_vlen_set function, there is an incorrect comparison between
vlen(bit) and vlenb(byte).
This will cause unexpected error when user applies the `vlen=1024` cpu
option with a vendor predefined cpu type that the default vlen is
1024(vlenb=128).
Fixes: 4f6d036ccc ("target/riscv/cpu.c: remove cpu->cfg.vlen")
Signed-off-by: Max Chou <max.chou@sifive.com>
Reviewed-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Message-ID: <20250124090539.2506448-1-max.chou@sifive.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
(cherry picked from commit bf3adf93f1)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
According to the Vector Reduction Operations section in the RISC-V "V"
Vector Extension spec,
"If vl=0, no operation is performed and the destination register is not
updated."
The vd should be updated when vl is larger than 0.
Fixes: fe5c9ab1fc ("target/riscv: vector single-width integer reduction instructions")
Fixes: f714361ed7 ("target/riscv: rvv-1.0: implement vstart CSR")
Signed-off-by: Max Chou <max.chou@sifive.com>
Reviewed-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Message-ID: <20250124101452.2519171-1-max.chou@sifive.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
(cherry picked from commit ffd455963f)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
In the syndrome value for a data abort, bit 21 is SSE, which is
set to indicate that the abort was on a sign-extending load. When
we handle the data abort from the guest via address_space_read(),
we forgot to handle this and so would return the wrong value if
the guest did a sign-extending load to an MMIO region. Add the
sign-extension of the returned data.
Cc: qemu-stable@nongnu.org
Signed-off-by: Joelle van Dyne <j@getutm.app>
Message-id: 20250224184123.50780-1-j@getutm.app
[PMM: Drop an unnecessary check on 'len'; expand commit message]
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
(cherry picked from commit 12c365315a)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
macOS 15.2's Hypervisor.framework exposes SME feature on M4 Macs.
However, QEMU's hvf accelerator code does not properly support it
yet, causing QEMU to fail to start when hvf accelerator is used on
these systems, with the error message:
qemu-aarch64-softmmu: cannot disable sme4224
All SME vector lengths are disabled.
With SME enabled, at least one vector length must be enabled.
Ideally we would have SME support on these hosts; however, until that
point, we must suppress the SME feature in the ID registers, so that
users can at least run non-SME guests.
Cc: qemu-stable@nongnu.org
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/2665
Signed-off-by: Joelle van Dyne <j@getutm.app>
Message-id: 20250224165735.36792-1-j@getutm.app
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
[PMM: expanded commit message, comment]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
(cherry picked from commit fd207677a8)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
It is possible to start QEMU with a confidential-guest-support object
even in TCG mode. While there is already a check in qemu_machine_creation_done:
if (machine->cgs && !machine->cgs->ready) {
error_setg(errp, "accelerator does not support confidential guest %s",
object_get_typename(OBJECT(machine->cgs)));
exit(1);
}
the creation of RAMBlocks happens earlier, in qemu_init_board(), if
the command line does not override the default memory backend with
-M memdev. Then the RAMBlock will try to use guest_memfd (because
machine_require_guest_memfd correctly returns true; at least correctly
according to the current implementation) and trigger the assertion
failure for kvm_enabled(). This happend with a command line as
simple as the following:
qemu-system-x86_64 -m 512 -nographic -object sev-snp-guest,reduced-phys-bits=48,id=sev0 \
-M q35,kernel-irqchip=split,confidential-guest-support=sev0
qemu-system-x86_64: ../system/physmem.c:1871: ram_block_add: Assertion `kvm_enabled()' failed.
Cc: Xiaoyao Li <xiaoyao.li@intel.com>
Cc: qemu-stable@nongnu.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Pankaj Gupta <pankaj.gupta@amd.com>
Reviewed-by: Xiaoyao Li <xiaoyao.li@intel.com>
Link: https://lore.kernel.org/r/20250217120812.396522-1-pbonzini@redhat.com
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
(cherry picked from commit 6debfb2cb1)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Write operation with R32 (orig_a0) and R34 (CSR_BADV) is discarded on
gdbstub implementation for LoongArch system. And return value should
be register size rather than 0, since it is used to calculate offset of
next register such as R33 (PC) in function handle_write_all_regs().
Cc: qemu-stable@nongnu.org
Fixes: ca61e75071 ("target/loongarch: Add gdb support.")
Signed-off-by: Bibo Mao <maobibo@loongson.cn>
Reviewed-by: Bibo Mao <maobibo@loongson.cn>
(cherry picked from commit 7bd4eaa847)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Use virtio_get_config_size() rather than sizeof(struct
virtio_snd_config) for the config_size in the vhost-user-snd frontend.
The frontend shall rely on device features for the size of the device
configuration space. The presence of `controls` in the config space
depends on VIRTIO_SND_F_CTLS according to the specification (v1.3):
`
5.14.4 Device Configuration Layout
...
controls
(driver-read-only) indicates a total number of all available control
elements if VIRTIO_SND_F_CTLS has been negotiated.
`
This fixes an issue introduced by commit ab0c7fb2 ("linux-headers:
update to current kvm/next") in which the optional field `controls` is
added to the virtio_snd_config structure. This breaks vhost-user-device
backends that do not implement the `controls` field.
Fixes: ab0c7fb22b ("linux-headers: update to current kvm/next")
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/2805
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Suggested-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: Matias Ezequiel Vara Larsen <mvaralar@redhat.com>
Message-Id: <20250217131255.829892-1-mvaralar@redhat.com>
Cc: qemu-stable@nongnu.org
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Reviewed-by: Dorinda Bassey <dbassey@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
(cherry picked from commit e87b6efb11)
(Mjt: context fix for 9.2)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
When we return a response packet from NSM, we need to indicate its
length according to the content of the response. Prior to this patch, we
returned the length of the source buffer, which may confuse guest code
that relies on the response size.
Fix it by returning the response payload size instead.
Fixes: bb154e3e0c ("device/virtio-nsm: Support for Nitro Secure Module device")
Reported-by: Vikrant Garg <vikrant1garg@gmail.com>
Signed-off-by: Alexander Graf <graf@amazon.com>
Message-Id: <20250213114541.67515-1-graf@amazon.com>
Reviewed-by: Dorjoy Chowdhury <dorjoychy111@gmail.com>
Fixes: bb154e3e0c ("device/virtio-nsm: Support for Nitro Secure Module device")<br>
Reported-by: Vikrant Garg <vikrant1garg@gmail.com>
Signed-off-by: Alexander Graf <graf@amazon.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Tested-by: Vikrant Garg <vikrant1garg@gmail.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
(cherry picked from commit 131fe64e63)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
The function `vhost_dev_init()` expects the `struct vhost_dev`
(passed as a parameter) to be fully initialized. This is important
because some parts of the code check whether `vhost_dev->config_ops`
is NULL to determine if it has been set (e.g. later via
`vhost_dev_set_config_notifier`).
To ensure this initialization, it’s better to allocate the entire
`CryptoDevBackendVhost` structure (which includes `vhost_dev`) using
`g_mem0()`, following the same approach used for other vhost devices,
such as in `vhost_net_init()`.
Fixes: 042cea274c ("cryptodev: add vhost-user as a new cryptodev backend")
Cc: qemu-stable@nongnu.org
Reported-by: myluo24@m.fudan.edu.cn
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Message-Id: <20250211135523.101203-1-sgarzare@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
(cherry picked from commit 83cb18ac45)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
AMD IOMMU provides the base address of control registers through
IVRS table and PCI capability. Since this base address is of 64 bit,
use 32 bits mask (instead of 16 bits) to set BAR low and high.
Fixes: d29a09ca68 ("hw/i386: Introduce AMD IOMMU")
Signed-off-by: Sairaj Kodilkar <sarunkod@amd.com>
Reviewed-by: Vasant Hegde <vasant.hegde@amd.com>
Message-Id: <20250207045354.27329-3-sarunkod@amd.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
(cherry picked from commit 3684717b74)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Interrupt passthrough is determine by the bits 191,190,187-184.
These bits are part of the 3rd quad word (i.e. index 2) in DTE. Hence
replace dte[3] by dte[2].
Fixes: b44159fe0 ("x86_iommu/amd: Add interrupt remap support when VAPIC is not enabled")
Signed-off-by: Sairaj Kodilkar <sarunkod@amd.com>
Reviewed-by: Vasant Hegde <vasant.hegde@amd.com>
Message-Id: <20250207045354.27329-2-sarunkod@amd.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
(cherry picked from commit 63dc0b8647)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
QEMU currently crashes when you try to inspect the properties of the
microvm machine:
$ echo '{ "execute": "qmp_capabilities" }
{ "execute": "qom-list-properties","arguments":
{ "typename": "microvm-machine"}}' | \
./qemu-system-x86_64 -qmp stdio
{"QMP": {"version": {"qemu": {"micro": 50, "minor": 2, "major": 9},
"package": "v9.2.0-1072-g60af367187-dirty"}, "capabilities": ["oob"]}}
{"return": {}}
qemu-system-x86_64: ../qemu/hw/i386/acpi-microvm.c:250:
void acpi_setup_microvm(MicrovmMachineState *):
Assertion `x86ms->fw_cfg' failed.
Aborted (core dumped)
This happens because the microvm machine adds a machine_done (and a
powerdown_req) notifier in their instance_init function - however, the
instance_init of machines are not only called for machines that are
realized, but also for machines that are introspected, so in this case
the listener is added for a microvm machine that is never realized. And
since there is already a running machine, the listener function is
triggered immediately, causing a crash since it was not for the right
machine it was meant for.
Such listener functions must never be installed from an instance_init
function. Let's do it from microvm_machine_state_init() instead - this
function is the MachineClass->init() function instead, i.e. guaranteed
to be only called once in the lifetime of a QEMU process.
Since the microvm_machine_done() and microvm_powerdown_req() were
defined quite late in the microvm.c file, we have to move them now
also earlier, so that we can get their function pointers from
microvm_machine_state_init() without having to introduce a separate
prototype for those functions earlier.
Reviewed-by: Sergio Lopez <slp@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20250123204708.1560305-1-thuth@redhat.com>
Reviewed-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
(cherry picked from commit 38ef383073)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
QEMU currently crashes when you try to inspect the machines based on
TYPE_PC_MACHINE for their properties:
$ echo '{ "execute": "qmp_capabilities" }
{ "execute": "qom-list-properties","arguments":
{ "typename": "pc-q35-10.0-machine"}}' \
| ./qemu-system-x86_64 -M pc -qmp stdio
{"QMP": {"version": {"qemu": {"micro": 50, "minor": 2, "major": 9},
"package": "v9.2.0-1070-g87e115c122-dirty"}, "capabilities": ["oob"]}}
{"return": {}}
Segmentation fault (core dumped)
This happens because TYPE_PC_MACHINE machines add a machine_init-
done_notifier in their instance_init function - but instance_init
of machines are not only called for machines that are realized,
but also for machines that are introspected, so in this case the
listener is added for a q35 machine that is never realized. But
since there is already a running pc machine, the listener function
is triggered immediately, causing a crash since it was not for the
right machine it was meant for.
Such listener functions must never be installed from an instance_init
function. Let's do it from pc_basic_device_init() instead - this
function is called from the MachineClass->init() function instead,
i.e. guaranteed to be only called once in the lifetime of a QEMU
process.
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/2779
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20250117192106.471029-1-thuth@redhat.com>
Reviewed-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
(cherry picked from commit de538288e4)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
When an eBPF program cannot be attached, virtio_net_load_ebpf() returns
false, and virtio_net_device_realize() enters the code path to handle
errors because of this, but it causes NULL dereference because no error
is generated.
Change virtio_net_load_ebpf() to return false only when a fatal error
occurred.
Fixes: b5900dff14 ("hw/net: report errors from failing to use eBPF RSS FDs")
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Message-Id: <20250116-software-v1-1-9e5161b534d8@daynix.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
(cherry picked from commit bc82af6b0d)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
TYPE_CHIPIDEA models an IP block which is also used in TYPE_ZYNQ_MACHINE which
itself is not an IMX device. CONFIG_ZYNQ selects CONFIG_USB_EHCI_SYSBUS while
TYPE_CHIPIDEA is a separate compilation unit, so only works by accident if
CONFIG_IMX is given. Fix that by extracting CONFIG_USB_CHIPIDEA from CONFIG_IMX.
cc: qemu-stable@nongnu.org
Fixes: 616ec12d0f "hw/arm/xilinx_zynq: Fix USB port instantiation"
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Message-id: 20250209103604.29545-1-shentey@gmail.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
(cherry picked from commit 464ce71a96)
(Mjt: context fixup due to missing
v9.2.0-1303-g1b326f278d05 "hw/pci-host/designware: Expose MSI IRQ")
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
The code for WFI/WFE trapping has several errors:
* it wasn't using arm_sctlr(), so it would look at SCTLR_EL1
even if the CPU was in the EL2&0 translation regime
* it was raising UNDEF, not Monitor Trap, for traps to
AArch32 EL3 because of SCR.{TWE,TWI}
* it was not honouring SCR.{TWE,TWI} when running in
AArch32 at EL3 not in Monitor mode
* it checked SCR.{TWE,TWI} even on v7 CPUs which don't have
those bits
Fix these bugs.
Cc: qemu-stable@nongnu.org
Fixes: b1eced713d ("target-arm: Add WFx instruction trap support")
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20250130182309.717346-15-peter.maydell@linaro.org
(cherry picked from commit 2b95a2d01b)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
There are not many traps in AArch32 which should trap to Monitor
mode, but these trap bits should trap not just lower ELs to Monitor
mode but also the non-Monitor modes running at EL3 (i.e. Secure
System, Secure Undef, etc).
We get this wrong because the relevant access functions implement the
AArch64-style logic of
if (el < 3 && trap_bit_set) {
return CP_ACCESS_TRAP_EL3;
}
which won't trap the non-Monitor modes at EL3.
Correct this error by using arm_is_el3_or_mon() instead, which
returns true when the CPU is at AArch64 EL3 or AArch32 Monitor mode.
(Since the new callsites are compiled also for the linux-user mode,
we need to provide a dummy implementation for CONFIG_USER_ONLY.)
This affects only:
* trapping of ERRIDR via SCR.TERR
* trapping of the debug channel registers via SDCR.TDCC
* trapping of GICv3 registers via SCR.IRQ and SCR.FIQ
(which we already used arm_is_el3_or_mon() for)
This patch changes the handling of SCR.TERR and SDCR.TDCC. This
patch only changes guest-visible behaviour for "-cpu max" on
the qemu-system-arm binary, because SCR.TERR
and SDCR.TDCC (and indeed the entire SDCR register) only arrived
in Armv8, and the only guest CPU we support which has any v8
features and also starts in AArch32 EL3 is the 32-bit 'max'.
Other uses of CP_ACCESS_TRAP_EL3 don't need changing:
* uses in code paths that can't happen when EL3 is AArch32:
access_trap_aa32s_el1, cpacr_access, cptr_access, nsacr_access
* uses which are in accessfns for AArch64-only registers:
gt_stimer_access, gt_cntpoff_access, access_hxen, access_tpidr2,
access_smpri, access_smprimap, access_lor_ns, access_pauth,
access_mte, access_tfsr_el2, access_scxtnum, access_fgt
* trap bits which exist only in the AArch64 version of the
trap register, not the AArch32 one:
access_tpm, pmreg_access, access_dbgvcr32, access_tdra,
access_tda, access_tdosa (TPM, TDA and TDOSA exist only in
MDCR_EL3, not in SDCR, and we enforce this in sdcr_write())
Cc: qemu-stable@nongnu.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20250130182309.717346-8-peter.maydell@linaro.org
(cherry picked from commit 4d436fb05c)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
In the gicv3_{irq,fiq,irqfiq}_access() functions, there is a check
which downgrades a CP_ACCESS_TRAP_EL3 to CP_ACCESS_TRAP if EL3 is not
AArch64. This has been there since the GIC was first implemented,
but it isn't right: if we are trapping because of SCR.IRQ or SCR.FIQ
then we definitely want to be going to EL3 (doing
AArch32.TakeMonitorTrapException() in pseudocode terms). We might
want to not take a trap at all, but we don't ever want to go to the
default target EL, because that would mean, for instance, taking a
trap to Hyp mode if the trapped access was made from Hyp mode.
(This might have been an attempt to work around our failure to
properly implement Monitor Traps.)
Remove the bogus check.
Cc: qemu-stable@nongnu.org
Fixes: 359fbe65e0 ("hw/intc/arm_gicv3: Implement GICv3 CPU interface registers")
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20250130182309.717346-7-peter.maydell@linaro.org
(cherry picked from commit d04c6c3c00)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
In system register access pseudocode the common pattern for
AArch32 registers with access traps to EL3 is:
at EL1 and EL2:
if HaveEL(EL3) && !ELUsingAArch32(EL3) && (SCR_EL3.TERR == 1) then
AArch64.AArch32SystemAccessTrap(EL3, 0x03);
elsif HaveEL(EL3) && ELUsingAArch32(EL3) && (SCR.TERR == 1) then
AArch32.TakeMonitorTrapException();
at EL3:
if (PSTATE.M != M32_Monitor) && (SCR.TERR == 1) then
AArch32.TakeMonitorTrapException();
(taking as an example the ERRIDR access pseudocode).
This implements the behaviour of (in this case) SCR.TERR that
"Accesses to the specified registers from modes other than Monitor
mode generate a Monitor Trap exception" and of SCR_EL3.TERR that
"Accesses of the specified Error Record registers at EL2 and EL1
are trapped to EL3, unless the instruction generates a higher
priority exception".
In QEMU we don't implement this pattern correctly in two ways:
* in access_check_cp_reg() we turn the CP_ACCESS_TRAP_EL3 into
an UNDEF, not a trap to Monitor mode
* in the access functions, we check trap bits like SCR.TERR
only when arm_current_el(env) < 3 -- this is correct for
AArch64 EL3, but misses the "trap non-Monitor-mode execution
at EL3 into Monitor mode" case for AArch32 EL3
In this commit we fix the first of these two issues, by
making access_check_cp_reg() handle CP_ACCESS_TRAP_EL3
as a Monitor trap. This is a kind of exception that we haven't
yet implemented(!), so we need a new EXCP_MON_TRAP for it.
This diverges from the pseudocode approach, where every access check
function explicitly checks for "if EL3 is AArch32" and takes a
monitor trap; if we wanted to be closer to the pseudocode we could
add a new CP_ACCESS_TRAP_MONITOR and make all the accessfns use it
when appropriate. But because there are no non-standard cases in the
pseudocode (i.e. where either it raises a Monitor trap that doesn't
correspond to an AArch64 SystemAccessTrap or where it raises a
SystemAccessTrap that doesn't correspond to a Monitor trap), handling
this all in one place seems less likely to result in future bugs
where we forgot again about this special case when writing an
accessor.
(The cc of stable here is because "hw/intc/arm_gicv3_cpuif: Don't
downgrade monitor traps for AArch32 EL3" which is also cc:stable
will implicitly use the new EXCP_MON_TRAP code path.)
Cc: qemu-stable@nongnu.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20250130182309.717346-6-peter.maydell@linaro.org
(cherry picked from commit 4cf4948651)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
The pseudocode for AT S1E2R and AT S1E2W says that they should be
UNDEFINED if executed at EL3 when EL2 is not enabled. We were
incorrectly using CP_ACCESS_TRAP and reporting the wrong exception
syndrome as a result. Use CP_ACCESS_TRAP_UNCATEGORIZED.
Cc: qemu-stable@nongnu.org
Fixes: 2a47df9532 ("target-arm: Wire up AArch64 EL2 and EL3 address translation ops")
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20250130182309.717346-4-peter.maydell@linaro.org
(cherry picked from commit ccda792945)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
R_NYXTL says that these AT insns should be UNDEFINED if they
would operate on an EL lower than EL3 and SCR_EL3.{NSE,NS} is
set to the Reserved {1, 0}. We were incorrectly reporting
them with the wrong syndrome; use CP_ACCESS_TRAP_UNCATEGORIZED
so they are reported as UNDEFINED.
Cc: qemu-stable@nongnu.org
Fixes: 1acd00ef14 ("target/arm/helper: Check SCR_EL3.{NSE, NS} encoding for AT instructions")
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20250130182309.717346-3-peter.maydell@linaro.org
(cherry picked from commit 1960d9701e)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
The access pseudocode for the CNTPS_TVAL_EL1, CNTPS_CTL_EL1 and
CNTPS_CVAL_EL1 secure timer registers says that they are UNDEFINED
from EL2 or NS EL1. We incorrectly return CP_ACCESS_TRAP from the
access function in these cases, which means that we report the wrong
syndrome value to the target EL.
Use CP_ACCESS_TRAP_UNCATEGORIZED, which reports the correct syndrome
value for an UNDEFINED instruction.
Cc: qemu-stable@nongnu.org
Fixes: b4d3978c2f ("target-arm: Add the AArch64 view of the Secure physical timer")
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20250130182309.717346-2-peter.maydell@linaro.org
(cherry picked from commit b819fd6994)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Update the code in net/slirp.c to be compatible with
libslirp 4.9.0, which deprecated slirp_pollfds_fill()
and started using slirp_os_socket type for sockets
(which is a 64-bit integer on win64) for all callbacks
starting with version 6 of the interface.
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Reviewed-by: Samuel Thibault <samuel.thibault@ens-lyon.org>
Message-ID: <20250130123253.864681-1-mjt@tls.msk.ru>
[thuth: Added some spaces to make checkpatch.pl happy]
Signed-off-by: Thomas Huth <thuth@redhat.com>
(cherry picked from commit f141caa270)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
The gdbstub implementation for the Sparc architecture would
incorrectly calculate the the floating point register offset.
This resulted in, for example, registers f32 and f34 to point to
the same value.
The issue was caused by the confusion between even register numbers
and even register indexes. For example, the register index of f32 is 64
and f34 is 65.
Cc: qemu-stable@nongnu.org
Fixes: 30038fd818 ("target-sparc: Change fpr representation to doubles.")
Signed-off-by: Mikael Szreder <git@miszr.win>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-ID: <20250214070343.11501-1-git@miszr.win>
(cherry picked from commit 7a74e46808)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
When complying with the alignment requested in the ELF and unmapping
the excess reservation, having align_end not aligned to the guest page
causes the unmap to be rejected by the alignment check at
target_munmap and later brk adjustments hit an EEXIST.
Fix by aligning the start of region to be unmapped.
Fixes: c81d1fafa6 ("linux-user: Honor elf alignment when placing images")
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/1913
Signed-off-by: Fabiano Rosas <farosas@suse.de>
[rth: Align load_end as well.]
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-ID: <20250213143558.10504-1-farosas@suse.de>
(cherry picked from commit 4b7b20a3b7)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
The SMC91C111 includes an MMU Command register which permits
the guest to remove entries from the RX FIFO. The datasheet
does not specify what happens if the guest tries to do this
when the FIFO is already empty; there are no status registers
containing error bits which might be applicable.
Currently we don't guard at all against pop of an empty
RX FIFO, with the result that we allow the guest to drive
the rx_fifo_len index to negative values, which will cause
smc91c111_receive() to write to the rx_fifo[] array out of
bounds when we receive the next packet.
Instead ignore attempts to pop an empty RX FIFO.
Cc: qemu-stable@nongnu.org
Fixes: 80337b66a8 ("NIC emulation for qemu arm-softmmu")
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/2780
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-ID: <20250207151157.3151776-1-peter.maydell@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
(cherry picked from commit 937df81af6)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
The current logic scans qemu.git/subprojects/ from *.wrap files to
determine whether or not to include the associated directories in the
release tarballs. However, the script assumes that it is being run from
the top-level of the source directory, which may not always be the case.
In particular, when generating releases via, e.g.:
make qemu-9.2.1.tar.xz
the $CWD will either be an arbitrary external build directory, or
qemu.git/build, and the exclusions will not be processed as expected.
Fix this by using the $src parameter passed to the script as the root
directory for the various subproject/ paths referenced by this logic.
Also, the error case at the beginning of the subproject_dir() will not
result in the error message being printed, and will instead produce an
error message about "error" not being a valid command. Fix this by using
basic shell commands.
Fixes: be27b5149c ("make-release: only leave tarball of wrap-file subprojects")
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Michael Tokarev <mjt@tls.msk.ru>
Cc: qemu-stable@nongnu.org
Signed-off-by: Michael Roth <michael.roth@amd.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
(cherry picked from commit b79b05d1a0)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Windows only:
The libSDL2 Windows message loop needs the libSDL2 Windows low
level keyboard hook procedure to grab the left and right Windows
keys correctly. Reenable the SDL2 Windows keyboard hook procedure.
Since SDL2 2.30.4 the SDL2 keyboard hook procedure also filters
out the special left Control key event for every Alt Gr key event
on keyboards with an international layout. This means the QEMU low
level keyboard hook procedure is no longer needed. Remove the QEMU
Windows keyboard hook procedure.
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/2139
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/2323
Signed-off-by: Volker Rümelin <vr_qemu@t-online.de>
Link: https://lore.kernel.org/r/20241231115950.6732-1-vr_qemu@t-online.de
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
(cherry picked from commit 4dafba778a)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
(Mjt: context fix in ui/sdl2.c (includes))
Commit 7452162ade introduced 'qom-path' argument to BLOCK_IO_ERROR
event but when the event is instantiated in 'send_qmp_error_event()' the
arguments for 'device' and 'qom_path' in
qapi_event_send_block_io_error() were reversed :
Generated code for sending event:
void qapi_event_send_block_io_error(const char *qom_path,
const char *device,
const char *node_name,
IoOperationType operation,
[...]
Call inside send_qmp_error_event():
qapi_event_send_block_io_error(blk_name(blk),
blk_get_attached_dev_path(blk),
bs ? bdrv_get_node_name(bs) : NULL, optype,
[...]
This results into reporting the QOM path as the device alias and vice
versa which in turn breaks libvirt, which expects the device alias being
either a valid alias or empty (which would make libvirt do the lookup by
node-name instead).
Cc: qemu-stable@nongnu.org
Fixes: 7452162ade ("qapi: add qom-path to BLOCK_IO_ERROR event")
Signed-off-by: Peter Krempa <pkrempa@redhat.com>
Message-ID: <09728d784888b38d7a8f09ee5e9e9c542c875e1e.1737973614.git.pkrempa@redhat.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
(cherry picked from commit 107c551de0)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
ASAN detected a leak when running the ahci-test
/ahci/io/dma/lba28/retry:
Direct leak of 35 byte(s) in 1 object(s) allocated from:
#0 in malloc
#1 in __vasprintf_internal
#2 in vasprintf
#3 in g_vasprintf
#4 in g_strdup_vprintf
#5 in g_strdup_printf
#6 in object_get_canonical_path ../qom/object.c:2096:19
#7 in blk_get_attached_dev_id_or_path ../block/block-backend.c:1033:12
#8 in blk_get_attached_dev_path ../block/block-backend.c:1047:12
#9 in send_qmp_error_event ../block/block-backend.c:2140:36
#10 in blk_error_action ../block/block-backend.c:2172:9
#11 in ide_handle_rw_error ../hw/ide/core.c:875:5
#12 in ide_dma_cb ../hw/ide/core.c:894:13
#13 in dma_complete ../system/dma-helpers.c:107:9
#14 in dma_blk_cb ../system/dma-helpers.c:129:9
#15 in blk_aio_complete ../block/block-backend.c:1552:9
#16 in blk_aio_write_entry ../block/block-backend.c:1619:5
#17 in coroutine_trampoline ../util/coroutine-ucontext.c:175:9
Plug the leak by freeing the device path string.
Signed-off-by: Fabiano Rosas <farosas@suse.de>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-ID: <20241111145214.8261-1-farosas@suse.de>
[PMD: Use g_autofree]
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-ID: <20241111170333.43833-3-philmd@linaro.org>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
(cherry picked from commit 23ea425c14)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
When a packet is sent with QEMU_NET_PACKET_FLAG_RAW by QEMU it
never includes virtio-net header even if qemu_get_vnet_hdr_len()
is not 0, and filter-dump is not managing this case.
The only user of QEMU_NET_PACKET_FLAG_RAW is announce_self,
we can show the problem using it and tcpddump:
- QEMU parameters:
.. -monitor stdio \
-netdev bridge,id=netdev0,br=virbr0 \
-device virtio-net,mac=9a:2b:2c:2d:2e:2f,netdev=netdev0 \
-object filter-dump,netdev=netdev0,file=log.pcap,id=pcap0
- HMP command:
(qemu) announce_self
- TCP dump:
$ tcpdump -nxr log.pcap
without the fix:
08:00:06:04:00:03 > 2e:2f:80:35:00:01, ethertype Unknown (0x9a2b), length 50:
0x0000: 2c2d 2e2f 0000 0000 9a2b 2c2d 2e2f 0000
0x0010: 0000 0000 0000 0000 0000 0000 0000 0000
0x0020: 0000 0000
with the fix:
ARP, Reverse Request who-is 9a:2b:2c:2d:2e:2f tell 9a:2b:2c:2d:2e:2f, length 46
0x0000: 0001 0800 0604 0003 9a2b 2c2d 2e2f 0000
0x0010: 0000 9a2b 2c2d 2e2f 0000 0000 0000 0000
0x0020: 0000 0000 0000 0000 0000 0000 0000
Fixes: 481c52320a ("net: Strip virtio-net header when dumping")
Cc: akihiko.odaki@daynix.com
Signed-off-by: Laurent Vivier <lvivier@redhat.com>
Reviewed-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Reviewed-by: Michael Tokarev <mjt@tls.msk.ru>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
(cherry picked from commit c6a1b591a6)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
b9ad513e18 ("net: Remove receive_raw()") adds an iovec entry
in qemu_deliver_packet_iov() to add the virtio-net header
in the data when QEMU_NET_PACKET_FLAG_RAW is set but forgets
to increase the number of iovec entries in the array, so
receive_iov() will only send the first entry (the virtio-net
entry, full of 0) and no data. The packet will be discarded.
The only user of QEMU_NET_PACKET_FLAG_RAW is announce_self.
We can see the problem with tcpdump:
- QEMU parameters:
.. -monitor stdio \
-netdev bridge,id=netdev0,br=virbr0 \
-device virtio-net,mac=9a:2b:2c:2d:2e:2f,netdev=netdev0 \
- HMP command:
(qemu) announce_self
- TCP dump:
$ sudo tcpdump -nxi virbr0
without the fix:
<nothing>
with the fix:
ARP, Reverse Request who-is 9a:2b:2c:2d:2e:2f tell 9a:2b:2c:2d:2e:2f, length 46
0x0000: 0001 0800 0604 0003 9a2b 2c2d 2e2f 0000
0x0010: 0000 9a2b 2c2d 2e2f 0000 0000 0000 0000
0x0020: 0000 0000 0000 0000 0000 0000 0000
Reported-by: Xiaohui Li <xiaohli@redhat.com>
Bug: https://issues.redhat.com/browse/RHEL-73891
Fixes: b9ad513e18 ("net: Remove receive_raw()")
Cc: akihiko.odaki@daynix.com
Signed-off-by: Laurent Vivier <lvivier@redhat.com>
Reviewed-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Reviewed-by: Michael Tokarev <mjt@tls.msk.ru>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
(cherry picked from commit 84dfdcbff3)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Node.js crashes in qemu-system-s390x with random SIGSEGVs / SIGILLs.
The v8 JIT used by Node.js can garbage collect and overwrite unused
code. Overwriting is performed by WritableJitAllocation::CopyCode(),
which ultimately calls memcpy(). For certain sizes, memcpy() uses the
MVC instruction.
QEMU implements MVC and other similar instructions using helpers. While
TCG store ops invalidate affected translation blocks automatically,
helpers must do this manually by calling probe_access_flags(). The MVC
helper does this using the access_prepare() -> access_prepare_nf() ->
s390_probe_access() -> probe_access_flags() call chain.
At the last step of this chain, the store size is replaced with 0. This
causes the probe_access_flags() -> notdirty_write() ->
tb_invalidate_phys_range_fast() chain to miss some translation blocks.
When this happens, QEMU executes a mix of old and new code. This
quickly leads to either a SIGSEGV or a SIGILL in case the old code
ends in the middle of a new instruction.
Fix by passing the true size.
Reported-by: Berthold Gunreben <azouhr@opensuse.org>
Cc: Sarah Kriesch <ada.lovelace@gmx.de>
Cc: qemu-stable@nongnu.org
Closes: https://bugzilla.opensuse.org/show_bug.cgi?id=1235709
Signed-off-by: Ilya Leoshkevich <iii@linux.ibm.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: David Hildenbrand <david@redhat.com>
Fixes: e2faabee78 ("accel/tcg: Forward probe size on to notdirty_write")
Message-ID: <20250128001338.11474-1-iii@linux.ibm.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
(cherry picked from commit e43ced8be1)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
qemu_ram_alloc_from_fd allocates space if file_size == 0. If non-zero,
it uses the existing space and verifies it is large enough, but the
verification was broken when the offset parameter was introduced. As
a result, a file smaller than offset passes the verification and causes
errors later. Fix that, and update the error message to include offset.
Peter provides this concise reproducer:
$ touch ramfile
$ truncate -s 64M ramfile
$ ./qemu-system-x86_64 -object memory-backend-file,mem-path=./ramfile,offset=128M,size=128M,id=mem1,prealloc=on
qemu-system-x86_64: qemu_prealloc_mem: preallocating memory failed: Bad address
With the fix, the error message is:
qemu-system-x86_64: mem1 backing store size 0x4000000 is too small for 'size' option 0x8000000 plus 'offset' option 0x8000000
Cc: qemu-stable@nongnu.org
Fixes: 4b870dc4d0 ("hostmem-file: add offset option")
Signed-off-by: Steve Sistare <steven.sistare@oracle.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Acked-by: David Hildenbrand <david@redhat.com>
Link: https://lore.kernel.org/r/1736967650-129648-3-git-send-email-steven.sistare@oracle.com
Signed-off-by: Fabiano Rosas <farosas@suse.de>
(cherry picked from commit 719168fba7)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
When USBPacket in OUT direction has larger payload
than the ep_out_buffer (of size 512), a buffer overflow
would occur.
It could be fixed by limiting the size of usb_packet_copy
to be at most buffer size. Further optimization gets rid
of the ep_out_buffer and directly uses ep_out as the target
buffer.
This is reported by a security researcher who artificially
constructed an OUT packet of size 2047. The report has gone
through the QEMU security process, and as this device is for
testing purpose and no deployment of it in virtualization
environment is observed, it is triaged not to be a security bug.
Cc: qemu-stable@nongnu.org
Fixes: d7d3491855 ("hw/usb: Add CanoKey Implementation")
Reported-by: Juan Jose Lopez Jaimez <thatjiaozi@gmail.com>
Signed-off-by: Hongren Zheng <i@zenithal.me>
Message-id: Z4TfMOrZz6IQYl_h@Sun
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
(cherry picked from commit 664280abdd)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
The pseudocode ResetSVEState() does:
FPSR = ZeroExtend(0x0800009f<31:0>, 64);
but QEMU's arm_reset_sve_state() called vfp_set_fpcr() by accident.
Before the advent of FEAT_AFP, this was only setting a collection of
RES0 bits, which vfp_set_fpsr() would then ignore, so the only effect
was that we didn't actually set the FPSR the way we are supposed to
do. Once FEAT_AFP is implemented, setting the bottom bits of FPSR
will change the floating point behaviour.
Call vfp_set_fpsr(), as we ought to.
(Note for stable backports: commit 7f2a01e736 moved this function
from sme_helper.c to helper.c, but it had the same bug before the
move too.)
Cc: qemu-stable@nongnu.org
Fixes: f84734b874 ("target/arm: Implement SMSTART, SMSTOP")
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20250124162836.2332150-4-peter.maydell@linaro.org
(cherry picked from commit 1edc3d43f2)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Configuring "--enable-user --disable-system --enable-tools" causes the
build failure with the following information:
/usr/bin/ld: libhwcore.a.p/hw_core_qdev.c.o: in function `device_finalize':
/qemu/build/../hw/core/qdev.c:688: undefined reference to `qapi_event_send_device_deleted'
collect2: error: ld returned 1 exit status
To fix the above issue, add qdev.c stub when build with `have_tools`.
With this fix, QEMU could be successfully built in the following cases:
--enable-user --disable-system --enable-tools
--enable-user --disable-system --disable-tools
--enable-user --disable-system
Cc: qemu-stable@nongnu.org
Fixes: 388b849fb6 ("stubs: avoid duplicate symbols in libqemuutil.a")
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/2766
Signed-off-by: Zhao Liu <zhao1.liu@intel.com>
Link: https://lore.kernel.org/r/20250121154318.214680-1-zhao1.liu@intel.com
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
(cherry picked from commit 8113dbbcda)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
We're seeing periodic reports of errors like:
$ qemu-img create -f luks --object secret,data=123456,id=sec0 \
-o key-secret=sec0 luks-info.img 1M
Formatting 'luks-info.img', fmt=luks size=1048576 key-secret=sec0
qemu-img: luks-info.img: Unable to get accurate CPU usage
This error message comes from a recent attempt to workaround a
kernel bug with measuring rusage in long running processes:
commit c72cab5ad9
Author: Tiago Pasqualini <tiago.pasqualini@canonical.com>
Date: Wed Sep 4 20:52:30 2024 -0300
crypto: run qcrypto_pbkdf2_count_iters in a new thread
Unfortunately this has a subtle bug on machines which are very fast.
On the first time around the loop, the 'iterations' value is quite
small (1 << 15), and so will run quite fast. Testing has shown that
some machines can complete this benchmarking task in as little as
7 milliseconds.
Unfortunately the 'getrusage' data is not updated at the time of
the 'getrusage' call, it is done asynchronously by the scheduler.
The 7 millisecond completion time for the benchmark is short
enough that 'getrusage' sometimes reports 0 accumulated execution
time.
As a result the 'delay_ms == 0' sanity check in the above commit
is triggering non-deterministically on such machines.
The benchmarking loop intended to run multiple times, increasing
the 'iterations' value until the benchmark ran for > 500 ms, but
the sanity check doesn't allow this to happen.
To fix it, we keep a loop counter and only run the sanity check
after we've been around the loop more than 5 times. At that point
the 'iterations' value is high enough that even with infrequent
updates of 'getrusage' accounting data on fast machines, we should
see a non-zero value.
Fixes: https://lore.kernel.org/qemu-devel/ffe542bb-310c-4616-b0ca-13182f849fd1@redhat.com/
Fixes: https://bugzilla.redhat.com/show_bug.cgi?id=2336437
Reported-by: Thomas Huth <thuth@redhat.com>
Reported-by: Richard W.M. Jones <rjones@redhat.com>
Tested-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Daniel P. Berrangé <berrange@redhat.com>
Message-ID: <20250109093746.1216300-1-berrange@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
(cherry picked from commit 145f12ea88)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
The QEMU source archive is including the sources downloaded from crates.io
in both tarball form (in subprojects/packagecache) and expanded/patched
form (in the subprojects directory). The former is the more authoritative
form, as it has a hash that can be verified in the wrap file and checked
against the download URL, so keep that one only. This works also with
--disable-download; when building QEMU for the first time from the
tarball, Meson will print something like
Using proc-macro2-1-rs source from cache.
for each subproject, and then go on to extract the tarball and apply the
overlay or the patches in subprojects/packagefiles.
Reported-by: Michael Tokarev <mjt@tls.msk.ru>
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/2719
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
(cherry picked from commit be27b5149c)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
This assertion always happens when we sanitize the CXL memory device.
$ echo 1 > /sys/bus/cxl/devices/mem0/security/sanitize
It is incorrect to register an MSIX number beyond the device's capability.
Increase the device's MSIX number to cover the mailbox msix number(9).
Fixes: 43efb0bfad ("hw/cxl/mbox: Wire up interrupts for background completion")
Signed-off-by: Li Zhijian <lizhijian@fujitsu.com>
Message-Id: <20250115075834.167504-1-lizhijian@fujitsu.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
(cherry picked from commit 1ce979e726)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Current versions of Windows call _DSM(func=7) regardless
of whether it is supported or not. It leads to NICs having bogus
'PCI Label Id = 0', where none should be set at all.
Also presence of 'PCI Label Id' triggers another Windows bug
on localized versions that leads to hangs. The later bug is fixed
in latest updates for 'Windows Server' but not in consumer
versions of Windows (and there is no plans to fix it
as far as I'm aware).
Given it's easy, implement Microsoft suggested workaround
(return invalid Package) so that affected Windows versions
could boot on QEMU.
This would effectvely remove bogus 'PCI Label Id's on NICs,
but MS teem confirmed that flipping 'PCI Label Id' should not
change 'Network Connection' ennumeration, so it should be safe
for QEMU to change _DSM without any compat code.
Smoke tested with WinXP and WS2022
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/774
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <20250115125342.3883374-3-imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
(cherry picked from commit 0b05339198)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
The end vector calculation has a bug that results in polling fewer
than required vectors when reading at a non-zero offset in PBA memory.
Fixes: bbef882cc1 ("msi: add API to get notified about pending bit poll")
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Message-Id: <20241212120402.1475053-1-npiggin@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
(cherry picked from commit 42e2a7a0ab)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
PCI hotplug for downstream endpoints on arm fails because Linux'
PCIe hotplug driver doesn't like the QEMU provided LNKSTA:
pcieport 0000:08:01.0: pciehp: Slot(2): Card present
pcieport 0000:08:01.0: pciehp: Slot(2): Link Up
pcieport 0000:08:01.0: pciehp: Slot(2): Cannot train link: status 0x2000
There's 2 cases where LNKSTA isn't setup properly:
* the downstream device has no express capability
* max link width of the bridge is 0
Move the sanity checks added via 88c869198a
("pci: Sanity test minimum downstream LNKSTA") outside of the
branch to make sure downstream ports always have a valid LNKSTA.
Signed-off-by: Sebastian Ott <sebott@redhat.com>
Tested-by: Zhenyu Zhang <zhenyzha@redhat.com>
Message-Id: <20241203121928.14861-1-sebott@redhat.com>
Reviewed-by: Alex Williamson <alex.williamson@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
(cherry picked from commit 694632fd44)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
QEMU would crash with a failed assertion if the XHCI controller
attempted to raise the interrupt on an interrupter corresponding
to a MSI vector with a higher index than the highest configured
for the device by the guest driver.
This behaviour is correct on the MSI/PCI side: per PCI 3.0 spec,
devices must ensure they do not send MSI notifications for
vectors beyond the range of those allocated by the system/driver
software. Unlike MSI-X, there is no generic way for handling
aliasing in the case of fewer allocated vectors than requested,
so the specifics are up to device implementors. (Section
6.8.3.4. "Sending Messages")
It turns out the XHCI spec (Implementation Note in section 4.17,
"Interrupters") requires that the host controller signal the MSI
vector with the number computed by taking the interrupter number
modulo the number of enabled MSI vectors.
This change introduces that modulo calculation, fixing the
failed assertion. This makes the device work correctly in MSI mode
with macOS's XHCI driver, which only allocates a single vector.
Signed-off-by: Phil Dennis-Jordan <phil@philjordan.eu>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-ID: <20250112210056.16658-2-phil@philjordan.eu>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
(cherry picked from commit bb5b7fced6)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
In ufs_write_attr_value(), the value parameter is handled in the CPU's
endian format but provided in big-endian format by the caller. Thus, it
is converted to the CPU's endian format. The related test code is also
fixed to reflect this change.
Fixes: 7c85332a2b ("hw/ufs: minor bug fixes related to ufs-test")
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Keoseong Park <keosung.park@samsung.com>
Reviewed-by: Jeuk Kim <jeuk20.kim@samsung.com>
Message-ID: <20250107084356epcms2p2af4d86432174d76ea57336933e46b4c3@epcms2p2>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
(cherry picked from commit 4572dacc33)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
When QPL compression is enabled on the migration channel and the same
dirty page changes from a normal page to a zero page in the iterative
memory copy, the dirty page will not be updated to a zero page again
on the target side, resulting in incorrect memory data on the source
and target sides.
The root cause is that the target side does not record the normal pages
to the receivedmap.
The solution is to add ramblock_recv_bitmap_set_offset in target side
to record the normal pages.
Signed-off-by: Yuan Liu <yuan1.liu@intel.com>
Reviewed-by: Jason Zeng <jason.zeng@intel.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Message-Id: <20241218091413.140396-4-yuan1.liu@intel.com>
Signed-off-by: Fabiano Rosas <farosas@suse.de>
(cherry picked from commit a523bc5216)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
When QPL compression is enabled on the migration channel and the same
dirty page changes from a normal page to a zero page in the iterative
memory copy, the dirty page will not be updated to a zero page again
on the target side, resulting in incorrect memory data on the source
and target sides.
The root cause is that the target side does not record the normal pages
to the receivedmap.
The solution is to add ramblock_recv_bitmap_set_offset in target side
to record the normal pages.
Signed-off-by: Yuan Liu <yuan1.liu@intel.com>
Reviewed-by: Jason Zeng <jason.zeng@intel.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Message-Id: <20241218091413.140396-3-yuan1.liu@intel.com>
Signed-off-by: Fabiano Rosas <farosas@suse.de>
(cherry picked from commit 2588a5f99b)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
When compression is enabled on the migration channel and
the pages processed are all zero pages, these pages will
not be sent and updated on the target side, resulting in
incorrect memory data on the source and target sides.
The root cause is that all compression methods call
multifd_send_prepare_common to determine whether to compress
dirty pages, but multifd_send_prepare_common does not update
the IOV of MultiFDPacket_t when all dirty pages are zero pages.
The solution is to always update the IOV of MultiFDPacket_t
regardless of whether the dirty pages are all zero pages.
Fixes: 303e6f54f9 ("migration/multifd: Implement zero page transmission on the multifd thread.")
Cc: qemu-stable@nongnu.org #9.0+
Signed-off-by: Yuan Liu <yuan1.liu@intel.com>
Reviewed-by: Jason Zeng <jason.zeng@intel.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Message-Id: <20241218091413.140396-2-yuan1.liu@intel.com>
Signed-off-by: Fabiano Rosas <farosas@suse.de>
(cherry picked from commit cdc3970f85)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Currently, if an array of pointers contains a NULL pointer, that
pointer will be encoded as '0' in the stream. Since the JSON writer
doesn't define a "pointer" type, that '0' will now be an uint8, which
is different from the original type being pointed to, e.g. struct.
(we're further calling uint8 "nullptr", but that's irrelevant to the
issue)
That mixed-type array shouldn't be compressed, otherwise data is lost
as the code currently makes the whole array have the type of the first
element:
css = {NULL, NULL, ..., 0x5555568a7940, NULL};
{"name": "s390_css", "instance_id": 0, "vmsd_name": "s390_css",
"version": 1, "fields": [
...,
{"name": "css", "array_len": 256, "type": "nullptr", "size": 1},
...,
]}
In the above, the valid pointer at position 254 got lost among the
compressed array of nullptr.
While we could disable the array compression when a NULL pointer is
found, the JSON part of the stream still makes part of downtime, so we
should avoid writing unecessary bytes to it.
Keep the array compression in place, but if NULL and non-NULL pointers
are mixed break the array into several type-contiguous pieces :
css = {NULL, NULL, ..., 0x5555568a7940, NULL};
{"name": "s390_css", "instance_id": 0, "vmsd_name": "s390_css",
"version": 1, "fields": [
...,
{"name": "css", "array_len": 254, "type": "nullptr", "size": 1},
{"name": "css", "type": "struct", "struct": {"vmsd_name": "s390_css_img", ... }, "size": 768},
{"name": "css", "type": "nullptr", "size": 1},
...,
]}
Now each type-discontiguous region will become a new JSON entry. The
reader should interpret this as a concatenation of values, all part of
the same field.
Parsing the JSON with analyze-script.py now shows the proper data
being pointed to at the places where the pointer is valid and
"nullptr" where there's NULL:
"s390_css (14)": {
...
"css": [
"nullptr",
"nullptr",
...
"nullptr",
{
"chpids": [
{
"in_use": "0x00",
"type": "0x00",
"is_virtual": "0x00"
},
...
]
},
"nullptr",
}
Reviewed-by: Peter Xu <peterx@redhat.com>
Message-Id: <20250109185249.23952-7-farosas@suse.de>
Signed-off-by: Fabiano Rosas <farosas@suse.de>
(cherry picked from commit 35049eb0d2)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
QEMU plays a trick with null pointers inside an array of pointers in a VMSD
field. See 07d4e69147 ("migration/vmstate: fix array of ptr with
nullptrs") for more details on why. The idea makes sense in general, but
it may overlooked the JSON writer where it could write nothing in a
"struct" in the JSON hints section.
We hit some analyze-migration.py issues on s390 recently, showing that some
of the struct field contains nothing, like:
{"name": "css", "array_len": 256, "type": "struct", "struct": {}, "size": 1}
As described in details by Fabiano:
https://lore.kernel.org/r/87pll37cin.fsf@suse.de
It could be that we hit some null pointers there, and JSON was gone when
they're null pointers.
To fix it, instead of hacking around only at VMStateInfo level, do that
from VMStateField level, so that JSON writer can also be involved. In this
case, JSON writer will replace the pointer array (which used to be a
"struct") to be the real representation of the nullptr field.
Signed-off-by: Peter Xu <peterx@redhat.com>
Message-Id: <20250109185249.23952-6-farosas@suse.de>
Signed-off-by: Fabiano Rosas <farosas@suse.de>
(cherry picked from commit 9867c3a7ce)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Rename vmstate_info_nullptr from "uint64_t" to "nullptr". This vmstate
actually reads and writes just a byte, so the proper name would be
uint8. However, since this is a marker for a NULL pointer, it's
convenient to have a more explicit name that can be identified by the
consumers of the JSON part of the stream.
Change the name to "nullptr" and add support for it in the
analyze-migration.py script. Arbitrarily use the name of the type as
the value of the field to avoid the script showing 0x30 or '0', which
could be confusing for readers.
Reviewed-by: Peter Xu <peterx@redhat.com>
Message-Id: <20250109185249.23952-5-farosas@suse.de>
Signed-off-by: Fabiano Rosas <farosas@suse.de>
(cherry picked from commit f52965bf0e)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
The parsing for the S390StorageAttributes section is currently leaving
an unconsumed token that is later interpreted by the generic code as
QEMU_VM_EOF, cutting the parsing short.
The migration will issue a STATTR_FLAG_DONE between iterations, which
the script consumes correctly, but there's a final STATTR_FLAG_EOS at
.save_complete that the script is ignoring. Since the EOS flag is a
u64 0x1ULL and the stream is big endian, on little endian hosts a byte
read from it will be 0x0, the same as QEMU_VM_EOF.
Fixes: 81c2c9dd5d ("tests/qtest/migration-test: Fix analyze-migration.py for s390x")
Reviewed-by: Peter Xu <peterx@redhat.com>
Message-Id: <20250109185249.23952-4-farosas@suse.de>
Signed-off-by: Fabiano Rosas <farosas@suse.de>
(cherry picked from commit 69d1f78456)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
The analyze-migration script was seen failing in s390x in misterious
ways. It seems we're reaching the VMSDFieldStruct constructor without
any fields, which would indicate an empty .subsection entry, a
VMSTATE_STRUCT with no fields or a vmsd with no fields. We don't have
any of those, at least not without the unmigratable flag set, so this
should never happen.
Add some debug statements so that we can see what's going on the next
time the issue happens.
Reviewed-by: Peter Xu <peterx@redhat.com>
Message-Id: <20250109185249.23952-2-farosas@suse.de>
Signed-off-by: Fabiano Rosas <farosas@suse.de>
(cherry picked from commit 86bee9e0c7)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Commit f5f48a7891 ("migration/multifd: Separate SYNC request with
normal jobs") changed the multifd source side to stop sending data
along with the MULTIFD_FLAG_SYNC, effectively introducing the concept
of a SYNC-only packet. Relying on that, commit d7e58f412c
("migration/multifd: Don't send ram data during SYNC") later came
along and skipped reading data from SYNC packets.
In a versions timeline like this:
8.2 f5f48a7 9.0 9.1 d7e58f41 9.2
The issue arises that QEMUs < 9.0 still send data along with SYNC, but
QEMUs > 9.1 don't gather that data anymore. This leads to various
kinds of migration failures due to desync/missing data.
Stop checking for a SYNC packet on the destination and unconditionally
unfill the packet.
>From now on:
old -> new:
the source sends data + sync, destination reads normally
new -> new:
source sends only sync, destination reads zeros
new -> old:
source sends only sync, destination reads zeros
CC: qemu-stable@nongnu.org
Fixes: d7e58f412c ("migration/multifd: Don't send ram data during SYNC")
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/2720
Reviewed-by: Peter Xu <peterx@redhat.com>
Signed-off-by: Fabiano Rosas <farosas@suse.de>
Message-Id: <20241213160120.23880-2-farosas@suse.de>
Signed-off-by: Fabiano Rosas <farosas@suse.de>
(cherry picked from commit b93d897ea2)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
TCG trace-events were deprecated before the v6.2 release,
and removed for v7.0.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Michael Tokarev <mjt@tls.msk.ru>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
(cherry picked from commit b4859e8f33)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Hardcoded 32 bytes is used for vbsrl emulation check, there is
problem when options lsx=on,lasx=off is used for vbsrl.v instruction
in TCG mode. It injects LASX exception rather LSX exception.
Here actual operand size is used.
Cc: qemu-stable@nongnu.org
Fixes: df97f33807 ("target/loongarch: Implement xvreplve xvinsve0 xvpickve")
Signed-off-by: Bibo Mao <maobibo@loongson.cn>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
(cherry picked from commit d41989e754)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
KVM is not happy when starting a VM with weird RAM sizes:
# qemu-system-s390x --enable-kvm --nographic -m 1234K
qemu-system-s390x: kvm_set_user_memory_region: KVM_SET_USER_MEMORY_REGION
failed, slot=0, start=0x0, size=0x244000: Invalid argument
kvm_set_phys_mem: error registering slot: Invalid argument
Aborted (core dumped)
Let's handle that in a better way by rejecting such weird RAM sizes
right from the start:
# qemu-system-s390x --enable-kvm --nographic -m 1234K
qemu-system-s390x: ram size must be multiples of 1 MiB
Message-ID: <20241219144115.2820241-2-david@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Eric Farman <farman@linux.ibm.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Acked-by: Janosch Frank <frankja@linux.ibm.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
(cherry picked from commit 14e568ab48)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
In the section "4.7 Precise effects on interrupt-pending bits"
of the RISC-V AIA specification defines that:
"If the source mode is Level1 or Level0 and the interrupt domain
is configured in MSI delivery mode (domaincfg.DM = 1):
The pending bit is cleared whenever the rectified input value is
low, when the interrupt is forwarded by MSI, or by a relevant
write to an in_clrip register or to clripnum."
Update the riscv_aplic_set_pending() to match the spec.
Fixes: bf31cf06eb ("hw/intc/riscv_aplic: Fix setipnum_le write emulation for APLIC MSI-mode")
Signed-off-by: Yong-Xuan Wang <yongxuan.wang@sifive.com>
Acked-by: Alistair Francis <alistair.francis@wdc.com>
Message-ID: <20241029085349.30412-1-yongxuan.wang@sifive.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
(cherry picked from commit 0d0141fadc)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Since commit 5286c36622 ("target/i386: properly reset TSC on reset")
QEMU writes the special value of "1" to each online vCPU TSC on VM reset
to reset it.
However parked vCPUs don't get that handling and due to that their TSCs
get desynchronized when the VM gets reset.
This in turn causes KVM to turn off PVCLOCK_TSC_STABLE_BIT in its exported
PV clock.
Note that KVM has no understanding of vCPU being currently parked.
Without PVCLOCK_TSC_STABLE_BIT the sched clock is marked unstable in
the guest's kvm_sched_clock_init().
This causes a performance regressions to show in some tests.
Fix this issue by writing the special value of "1" also to TSCs of parked
vCPUs on VM reset.
Reproducing the issue:
1) Boot a VM with "-smp 2,maxcpus=3" or similar
2) device_add host-x86_64-cpu,id=vcpu,node-id=0,socket-id=0,core-id=2,thread-id=0
3) Wait a few seconds
4) device_del vcpu
5) Inside the VM run:
# echo "t" >/proc/sysrq-trigger; dmesg | grep sched_clock_stable
Observe the sched_clock_stable() value is 1.
6) Reboot the VM
7) Once the VM boots once again run inside it:
# echo "t" >/proc/sysrq-trigger; dmesg | grep sched_clock_stable
Observe the sched_clock_stable() value is now 0.
Fixes: 5286c36622 ("target/i386: properly reset TSC on reset")
Signed-off-by: Maciej S. Szmigiero <maciej.szmigiero@oracle.com>
Link: https://lore.kernel.org/r/5a605a88e9a231386dc803c60f5fed9b48108139.1734014926.git.maciej.szmigiero@oracle.com
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
(cherry picked from commit 3f2a05b31e)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
The macOS builds in our CI (and possibly other very recent distros)
are currently broken since the update to libnfs version 6 there.
That version apparently comes with a big API breakage. v5.0.3 was
the final release of the old API (see the libnfs commit here:
https://github.com/sahlberg/libnfs/commit/4379837 ).
Disallow version 6.x for now to get the broken CI job working
again. Once somebody had enough time to adapt our code in
block/nfs.c, we can revert this change again.
Message-ID: <20241218065157.209020-1-thuth@redhat.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Thomas Huth <thuth@redhat.com>
(cherry picked from commit e2d98f2571)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
In the GICv3 ITS model, we have a common coding pattern which has a
local C struct like "DTEntry dte", which is a C representation of an
in-guest-memory data structure, and we call a function such as
get_dte() to read guest memory and fill in the C struct. These
functions to read in the struct sometimes have cases where they will
leave early and not fill in the whole struct (for instance get_dte()
will set "dte->valid = false" and nothing else for the case where it
is passed an entry_addr implying that there is no L2 table entry for
the DTE). This then causes potential use of uninitialized memory
later, for instance when we call a trace event which prints all the
fields of the struct. Sufficiently advanced compilers may produce
-Wmaybe-uninitialized warnings about this, especially if LTO is
enabled.
Rather than trying to carefully separate out these trace events into
"only the 'valid' field is initialized" and "all fields can be
printed", zero-init all the structs when we define them. None of
these structs are large (the biggest is 24 bytes) and having
consistent behaviour is less likely to be buggy.
Cc: qemu-stable@nongnu.org
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/2718
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-id: 20241213182337.3343068-1-peter.maydell@linaro.org
(cherry picked from commit 9678b9c505)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
If the binary loaded via -kernel is *not* a linux kernel (in which
case protocol == 0), do not patch the linux kernel header fields.
It's (a) pointless and (b) might break binaries by random patching
and (c) changes the binary hash which in turn breaks secure boot
verification.
Background: OVMF happily loads and runs not only linux kernels but
any efi binary via direct kernel boot.
Note: Breaking the secure boot verification is a problem for linux
kernels too, but fixed that is left for another day ...
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Message-ID: <20240905141211.1253307-3-kraxel@redhat.com>
(cherry picked from commit 57e2cc9abf)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
The released fix for this CVE:
f6b0de53fb ("9pfs: prevent opening special files (CVE-2023-2861)")
caused a regression with security_model=passthrough. When handling a
'Tmknod' request there was a side effect that 'Tmknod' request could fail
as 9p server was trying to adjust permissions:
#6 close_if_special_file (fd=30) at ../hw/9pfs/9p-util.h:140
#7 openat_file (mode=<optimized out>, flags=2228224,
name=<optimized out>, dirfd=<optimized out>) at
../hw/9pfs/9p-util.h:181
#8 fchmodat_nofollow (dirfd=dirfd@entry=31,
name=name@entry=0x5555577ea6e0 "mysocket", mode=493) at
../hw/9pfs/9p-local.c:360
#9 local_set_cred_passthrough (credp=0x7ffbbc4ace10, name=0x5555577ea6e0
"mysocket", dirfd=31, fs_ctx=0x55555811f528) at
../hw/9pfs/9p-local.c:457
#10 local_mknod (fs_ctx=0x55555811f528, dir_path=<optimized out>,
name=0x5555577ea6e0 "mysocket", credp=0x7ffbbc4ace10) at
../hw/9pfs/9p-local.c:702
#11 v9fs_co_mknod (pdu=pdu@entry=0x555558121140,
fidp=fidp@entry=0x5555574c46c0, name=name@entry=0x7ffbbc4aced0,
uid=1000, gid=1000, dev=<optimized out>, mode=49645,
stbuf=0x7ffbbc4acef0) at ../hw/9pfs/cofs.c:205
#12 v9fs_mknod (opaque=0x555558121140) at ../hw/9pfs/9p.c:3711
That's because server was opening the special file to adjust permissions,
however it was using O_PATH and it would have not returned the file
descriptor to guest. So the call to close_if_special_file() on that branch
was incorrect.
Let's lift the restriction introduced by f6b0de53fb such that it would
allow to open special files on host if O_PATH flag is supplied, not only
for 9p server's own operations as described above, but also for any client
'Topen' request.
It is safe to allow opening special files with O_PATH on host, because
O_PATH only allows path based operations on the resulting file descriptor
and prevents I/O such as read() and write() on that file descriptor.
Fixes: f6b0de53fb ("9pfs: prevent opening special files (CVE-2023-2861)")
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/2337
Reported-by: Dirk Herrendorfer <d.herrendoerfer@de.ibm.com>
Signed-off-by: Christian Schoenebeck <qemu_oss@crudebyte.com>
Reviewed-by: Greg Kurz <groug@kaod.org>
Tested-by: Dirk Herrendorfer <d.herrendoerfer@de.ibm.com>
Message-Id: <E1tJWbk-007BH4-OB@kylie.crudebyte.com>
(cherry picked from commit d06a9d843f)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
2024-12-13 00:21:17 +03:00
212 changed files with 2170 additions and 1115 deletions
Some files were not shown because too many files have changed in this diff
Show More
Reference in New Issue
Block a user
Blocking a user prevents them from interacting with repositories, such as opening or commenting on pull requests or issues. Learn more about blocking a user.
Michael Tokarev
Icenowy