The APQ8096 DB820c platform provides HDMI output. The MDSS block on
8x96 supports a direct HDMI out. Populate the MDSS, MDP and HDMI DT
nodes. Also, add the HDMI HPD and DDC pinctrl nodes with the bias
and driver strength specified for this platform.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Andy Gross <agross@kernel.org>
With the addition of "private_objs" in drm_atomic_state, we no longer
need to subclass drm_atomic_state to store state of share resources
that don't perfectly fit within planes/crtc/connector state information.
We can now save this state within drm_atomic_state itself using
the private objects.
Remove the infrastructure that allowed subclassing of drm_atomic_state
in the driver.
Changes in v3:
- Added to the msm atomic helper patch set
Changes in v4:
- None
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
This replaces the usage of the subclassed atomic state (mdp5_state)
with a private_obj state embedded within drm_atomic_state. The latter
method is the preferred approach, since it's simpler to implement
and less prone to errors.
The new API replaces the older and equivalent mdp5_state usage in the
following pattern:
- References to "mdp5_kms->state" (i.e, the old/existing state) is
replaced with mdp5_get_existing_global_state(). In the atomic_check
path, this should be called with the glob_state_lock drm_modeset_lock
alredy taken.
- References to "mdp5_get_state()" are replaced with
mdp5_get_global_state(). This acquires glob_state_lock and uses
drm_atomic_get_private_obj_state() to create a new duplicated state.
Changes in v3:
- Acquire glob_state_lock in mdp5_smp.c
- Added to the msm atomic helper patch set
Changes in v4:
- None
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Global shared resources (hwpipes, hwmixers and SMP) for MDP5 are
implemented as a part of atomic state by subclassing drm_atomic_state.
The preferred approach is to use the drm_private_obj infrastructure
available in the atomic core.
mdp5_global_state is introduced as a drm atomic private object. The two
funcs mdp5_get_global_state() and mdp5_get_existing_global_state() are
the two variants that will be used to access mdp5_global_state.
This will replace the existing mdp5_state struct (which subclasses
drm_atomic_state) and the funcs around it. These will be removed later
once we mdp5_global_state is put to use everywhere.
Changes in v3:
- Added glob_state_lock instead of pushing it into the core
- Added to the msm atomic helper patch set
Changes in v4:
- None
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Newer DSI host controllers (SDM845 in particular) require a new clock
called byte_intf_clk. A recent patch tried to add this as an optional
clock, but it still set 'ret' to an error number if it didn't find it.
This breaks the host's probe for all previous DSI host versions.
Instead of setting this up as an optional clock, try to get the clock
only for the DSI version that supports it.
Fixes: 56558fb ("drm/msm/dsi: Add byte_intf_clk")
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
SDM845 uses a newer revision (v2.0+) of the 6G DSI controller. This
revision has another clock input at the block boundary called the byte
interface clock. Specify this new clock in the binding.
A 10nm DSI PHY is used along with the controller. Add a compatible
string for it and specify its base address/regulator supply needs.
Cc: Rob Herring <robh@kernel.org>
Cc: devicetree@vger.kernel.org
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Add the compatible string for 14nm DSI PHY (used in MSM8996/APQ8096).
>From 14nm PHY onwards, the "dsi_phy_regulator" reg-name is not required,
but "dsi_phy_lane" reg-name is. Update the doc to specify the reg-names
each PHY revision needs.
Cc: Rob Herring <robh@kernel.org>
Cc: devicetree@vger.kernel.org
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
DSI6G v2.0+ blocks have a new clock input to them called
byte_intf_clk. It's rate is to be set as byte_clk / 2.
Within the clock controller (CC) subsystem, this clock is a
child/descendant of the byte_clk.
Set it up as an optional clock in the DSI host driver. Make sure
that we enable/set its rate only after we configure byte_clk.
This is required for the ancestor clocks in the CC to be
configured correctly.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
We try to get the interface clock in dsi_get_config early during DSI's
component bind. Try getting both the "iface" and "iface_clk" clock name
variants so that we are compatible with both new and legacy DT.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Populate the PHY ops with the downstream driver as reference.
There are a couple of TODOs which need to be resolved:
- The PHY timings are all hardcoded for now. This needs to be replaced
with automatic calculations once we get/understand them.
- There are some lane configuration registers which use a new
representation between physical and logical lane mappings. For now,
we've hardcoced them to follow the default mapping (i.e
logical 0 -> phy 0, logical 1 -> phy 1 etc).
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Populate PLL clock ops from downstream. This contains the VCO PLL
ops and the registration of standard clk_divider and clk_mux clocks.
Unlike 14nm PLL, the postdividers/mux of the slave PLL doesn't need
to be set to the same values of the postdivs/mux of the master PLL.
Hence, we don't need special postdivider clock ops like we did with
the 14nm PLL driver.
Like the previous PLL drivers, the implementation is slightly different
from downstream. We don't use shadow clocks, but have the ability to
reparent the RCGs to a different source.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Add new 10nm DSI PLL/PHY files that will be used on SDM845.
Just populate empty pll/phy funcs for now. These will be filled up
later.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
The msm/kms driver should work even if there is no GPU device specified
in DT. Currently, we get a NULL dereference crash in adreno_load_gpu
since the driver assumes that priv->gpu_pdev is non-NULL.
Perform an additional check on priv->gpu_pdev before trying to retrieve
the msm_gpu pointer from it.
v2: Incorporate Jordan's comments:
- Simplify the check to share the same error message.
- Use dev_err_once() to avoid an error message every time we open the
drm device fd.
Fixes: eec874ce5f (drm/msm/adreno: load gpu at probe/bind time)
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Acked-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
When a plane moves out of bounds (i.e, outside the crtc clip region), the
plane state's "visible" parameter changes to false. When this happens, we
(a) release the hwpipe resources away from it, and
(b) unstage the corresponding hwpipe(s) from the Layer Mixers in the CRTC.
(a) requires use to acquire the global atomic state and assign a new
hwpipe. (b) requires us to re-configure the Layer Mixer, which is done in
the CRTC. We don't want to do these things in the async plane update path,
so return an error if the new state's "visible" isn't the same as the
current state's "visible".
Cc: Gustavo Padovan <gustavo.padovan@collabora.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
MDP5 on newer SoCs support cursor planes (i.e, cursor SSPPs). They are a
separate entity unlike the cursors within LM.
Do not try to restore the MDP5 LM cursor registers, or the corresponding
CTL bits if we are not using LM cursors.
Also, since we've introduced a new variable 'lm_cursor_enabled', we can
now use it to avoid creating a different sets of crtc_funcs for CRTCs
with LM cursors and CRTCs with cursor planes.
Fixes: "drm/msm/mdp5: restore cursor state when enabling crtc"
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
We currently call mdp5_pipe_assign() twice to assign the left and right
hwpipes for our drm_plane. When merging 2 hwpipes, there are a few
constraints that we need to keep in mind:
- Only the same types of SSPPs are preferred. I.e, a RGB pipe should
be paired with another RGB pipe, VIG with VIG etc.
- The hwpipe staged on the left should have a higher priority than
the hwpipe staged on the right. The priorities are as follows:
VIG0 > VIG1 > VIG2 > VIG3
RGB0 > RGB1 > RGB2 > RGB3
DMA0 > DMA1
We can't apply these constraints easily if mdp5_pipe_assign() is
called twice. Update mdp5_pipe_assign() to find both hwpipes in
one go, and add the extra constraints needed.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
mdp5_pipe_assign currently returns the hwpipe pointer for the drm_plane.
Return it indirectly by setting a pointer passed as an argument. This
is needed because we want the func to find out the right hwpipe too.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
This was used as a placeholder. It was never really input to the MDSS/HDMI
clocks.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
While converting mdp5_enable/disable() calls to pm_runtime_get/put() API,
an extra call to pm_runtime_put_autosuspend() crept in
mdp5_crtc_cursor_set(). This results in calling the suspend handler
twice, and therefore clk_disables twice, which isn't a nice thing to do.
Fixes: d68fe15b18 (drm/msm/mdp5: Use runtime PM get/put API instead ...)
Reported-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
The DSI runtime PM suspend/resume callbacks check whether
msm_host->cfg_hnd is non-NULL before trying to enable the bus clocks.
This is done to accommodate early calls to these functions that may
happen before the bus clocks are even initialized.
Calling pm_runtime_put_autosuspend() in dsi_host_init() can result in
racy behaviour since msm_host->cfg_hnd is set very soon after. If the
suspend callback happens too late, we end up trying to disable clocks
that were never enabled, resulting in a bunch of WARN_ON splats.
Use pm_runtime_put_sync() so that the suspend callback is called
immediately.
Reported-by: Nicolas Dechesne <nicolas.dechesne@linaro.org>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
MDSS represents the top level wrapper that contains MDP5, DSI, HDMI and
other sub-blocks. W.r.t device heirarchy, it's the parent of all these
devices. The power domain of this device is actually tied to the GDSC
hw. When any sub-device enables its PD, MDSS's PD is also enabled.
The suspend/resume ops enable the top level clocks that end at the MDSS
boundary. For now, we're letting them all be optional, since the child
devices anyway hold a ref to these clocks.
Until now, we'd called a runtime_get() during probe, which ensured that
the GDSC was always on. Now that we've set up runtime PM for the children
devices, we can get rid of this hack.
Note: that the MDSS device is the platform_device in msm_drv.c. The
msm_runtime_suspend/resume ops call the funcs that enable/disable
the top level MDSS clocks. This is different from MDP4, where the
platform device created in msm_drv.c represents MDP4 itself. It would
have been nicer to hide these differences by adding new kms funcs, but
runtime PM needs to be enabled before kms is set up (i.e, msm_kms_init
is called).
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Requests for assigning/freeing SMP blocks by planes are collected during
the atomic check phase, and represented by mdp5_smp_state's 'assigned'
and 'released' members.
Once the atomic state is committed, these members are reset to 0,
indicating that the existing configuration satisfies all the planes.
Future atomic commits will copy the old mdp5_smp_state, and the 'assigned'
and 'released' members would be updated only if there was a change in
the plane configurations.
When we disable and re-enable display, we lose the values we wrote to the
SMP registers, but the code doesn't program the registers because there
isn't any change in mdp5_smp_state.
Fix this by writing to the registers irrespective of whether there was
a change in SMP state or not. We do this by keeping a cache of the
register values, and write them every time we commit a state.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
We shouldn't use use mode_set/mode_set_nofb helpers when we use runtime
PM. The registers configured in these funcs lose their state when we
eventually enable the display pipeline.
Do not implement these vfuncs in the helpers, and call them in the
crtc_enable/encoder_enable paths instead.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
The bus clocks are always enabled/disabled along with the power
domain, so move it to the runtime suspend/resume ops. This cleans
up the clock code a bit. Get rid of the clk_mutex mutex since it
isn't needed.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Call the pm_runtime_get/put API where we need the clocks enabled.
The main entry/exit points are 1) enabling/disabling the DSI bridge
and 2) Sending commands from the DSI host to the device.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Enable rudimentary runtime PM in the HDMI driver. We can't really do
agressive PM toggling at the moment because we need to leave the hpd
clocks enabled all the time. There isn't much benefit of creating
suspend/resume ops to toggle clocks either.
We just make sure that we configure the power domain in the HDMI bridge's
enable/disable paths, and the HDMI connector's detect() op.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
mdp5_enable/disable calls are scattered all around in the MDP5 code.
Use the pm_runtime_get/put calls here instead, and populate the
runtime PM suspend/resume ops to manage the clocks.
About the overall design: MDP5 is a child of the top level MDSS
device. MDSS is also the parent to DSI, HDMI and other interfaces. When
we enable MDP5's power domain, we end up enabling MDSS's PD too. It is
only MDSS's PD that actually controlls the GDSC HW. Therefore, calling
runtime_get/put on the MDP5 device is like just requesting a vote to
enable/disable the GDSC.
Functionally, replacing the clock enable/disable calls with the RPM API
can result in the power domain (GDSC) state being toggled if no other
child isn't powered on. This can result in the register context being lost.
We make sure (in future commits) that code paths don't end up configuring
registers and then later lose state, resulting in a bad HW state.
For now, we've replaced each mdp5_enable/disable with runtime_get/put API.
We could optimize things later by removing runtime_get/put calls which
don't really need to be there. This could prevent unnecessary toggling of
the power domain and clocks.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
msm_gpu's get_timestamp() op (called by the MSM_GET_PARAM ioctl) can
result in register accesses. We need our power domain and clocks to
be active for that. Make sure they are enabled here.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
We have upstream bindings (msm8916) that have the "_clk" suffix in the
clock names. The downstream bindings also require it.
We want to drop the "_clk" suffix and at the same time support existing
bindings. Update the MDP5 code with the the msm_clk_get() helper to
support both old and new clock names.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
The mdp5_cmd_encoder_disable is accidentally called in the encoder enable
path. We've not seen any problems since we haven't tested with command
mode panels in a while. Fix the copy-paste error.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
After the commit mentioned below, we start computing the byte and pixel
clocks (dsi_calc_clk_rate) in the DSI bridge's mode_set() op. The
calculation involves the number of DSI lanes being used by the
downstream bridge/panel.
If the downstream bridge/panel tries to change the number of DSI lanes
(as done in the ADV7533 driver) in its mode_set() op, then our DSI
host driver will not have the correct number of lanes when computing
byte/pixel clocks.
Fix this by delaying the clock rate calculation in the DSI bridge
enable path. In particular, compute the clock rates in
msm_dsi_host_get_phy_clk_req().
This fixes the DSI host error interrupts seen when we try to switch
between modes that require different number of lanes (4 to 3 lanes, or
vice versa) on db410c. The error interrupts occur since the byte/pixel
clock rates aren't according to what the DSI video mode timing engine
expects.
Fixes: b62aa70a98 ("drm/msm/dsi: Move PHY operations out of host")
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
A 2 pixel wide pink strip was observed on the left end of some HDMI
monitors configured in a HDMI mode.
It turned out that we were missing out on configuring AVI infoframes, and
unlike APQ8064, the 8x96 HDMI H/W seems to be sensitive to that.
Add configuration of AVI infoframes. While at it, make sure that
hdmi_audio_update is only called when we've detected that the monitor
supports HDMI.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Without doing anything in unprepare, the HDMI driver isn't able to
switch modes successfully. Calling set_rate with a new rate results
in an un-locked PLL.
If we reset the PLL in unprepare, the PLL is able to lock with the
new rate.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Currently, the duplicated sg table is freed in the detach() and
the error path of map_dma_buf() ion's dma_buf_ops.
If a call to dma_buf_map_attachment() fails, the importer is
expected to call dma_buf_detach() to remove the attachment. This
will result in us trying to free the duped sg table twice.
Don't call free_duped_table() in ion_map_dma_buf() to avoid this.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Acked-by: Laura Abbott <labbott@redhat.com>
Reviewed-by: Sumit Semwal <sumit.semwal@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A few members in ion_buffer struct are unused after features
like page faulting, ion_handle and ion_client were removed.
Remove these members and the leftover references to them.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Reviewed-by: Sumit Semwal <sumit.semwal@linaro.org>
Acked-by: Laura Abbott <labbott@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
3D mux is a small block placed after the DSPPs in MDP5. It can merge
2 LM/DSPP outputs and feed it to a single interface.
Enable 3D Mux if our mdp5_pipeline has 2 active LMs. This check
will need to be made more specific later when we add Dual DSI
support with source split enabled. In that use case, each LM feeds to a
separae INTF, so the 3D mux isn't needed.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Assigning LMs dynamically to CRTCs results in REG_MDP5_CTL_LAYER_REGs
and REG_MDP5_CTL_LAYER_EXT_REGs maintaining old values for a LM that
isn't used by our CTL instance anymore.
Clear the ctl's CTL_LAYER_REG and CTL_LAYER_EXT_REGs for all LM
instances. The ones that need to be configured are configured later
in this func.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Dynamically assign a right mixer to mdp5_crtc_state in the CRTC's
atomic_check path. Assigning the right mixer has some constraints,
i.e, only a few LMs can be paired together. Update mdp5_mixer_assign
to handle these constraints.
Firstly, we need to identify whether we need a right mixer or not.
At the moment, there are 2 scenarios where a right mixer might be
needed:
- If any of the planes connected to this CRTC is too wide (i.e, is
comprised of 2 hwpipes).
- If the CRTC's mode itself is too wide (i.e, a 4K mode on HDMI).
We implement both these checks in the mdp5_crtc_atomic_check(), and
pass 'need_right_mixer' to mdp5_setup_pipeline.
If a CRTC is already assigned a single mixer, and a new atomic commit
brings in a drm_plane that needs 2 hwpipes, we can successfully commit
this mode without requiring a full modeset, provided that we still use
the previously assigned mixer as the left mixer. If such an assignment
isn't possible, we'd need to do a full modeset. This scenario has been
ignored for now.
The mixer assignment code is a bit messy, considering we have at most
4 LM instances in hardware. This can probably be re-visited later with
simplified logic.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
If a CRTC comprises of 2 LMs, it is mandatory to enable border out
and assign it to the base stage.
We had to enable border out also when the base plane wasn't fullscreen.
Club these checks and put them in a separate function called
get_start_stage() that returns the starting stage for assigning planes.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Now that our mdp5_planes can consist of 2 hwpipes, update the
blend_setup() code to stage the right hwpipe to the left and
right LMs
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
In order to enable Source Split in HW, we need to add/modify
a few LM register configurations:
- Configure the LM width to be half the mode width, so that
each LM manages one half of the scanout.
- Tell the 'right' LM that it is configured to be the 'right'
LM in source split mode.
- Since we now have 2 places where REG_MDP5_LM_BLEND_COLOR_OUT is
configured, do a read-update-store for the register instead of
directly writing a value to it.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Now that we have a right hwpipe in mdp5_plane_state, configure it
mdp5_plane_mode_set(). The only parameters that vary between the
left and right hwpipes are the src_w, src_img_w, src_x and crtc_x
as we just even chop the fb into left and right halves.
Add a mdp5_plane_right_pipe() which will be used by the crtc code
to set up LM stages.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
If the drm_plane has a source width that's greater than the max width
supported by a SSPP (2560 pixels on 8x96), then we assign a 'r_hwpipe'
to it in mdp5_plane_atomic_check().
TODO: There are a few scenarios where the hwpipe assignments aren't
recommended by HW. For example, an assignment which results in a
drm_plane to of two different types of hwpipes (say RGB0 on left
and DMA1 on right) is not recommended.
Also, hwpipes have a priority mapping, where the higher priority pipe
needs to be staged on left LM, and the lower priority needs to be
staged on the right LM. For example, the priority order for VIG pipes
in decreasing order of priority is VIG0, VIG1, VIG2, and VIG3. So, VIG0
on left and VIG1 on right is a correct configuration, but VIG1 on left
and VIG0 on right isn't. These scenarios are ignored for now for the
sake of simplicity.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Refactor mdp5_plane_mode_set to call mdp5_hwpipe_mode_set. The latter
func takes in only the hwpipe and the parameters that need to be
programmed into the hwpipe registers. All the code that calculates these
parameters is left as is in mdp5_plane_mode_set.
In the future, when we let drm_plane be comprised of 2 hwpipes, this func
allow us to configure each pipe without adding redundant code.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Add another mdp5_hw_mixer pointer (r_mixer) in mdp5_crtc_state.
This mixer will be used to generate the right half of the scanout.
With Source Split, a SSPP can now be connected to 2 Layer Mixers, but
has to be at the same blend level (stage #) on both Layer Mixers.
A drm_plane that has a lesser width than the max width supported, will
comprise of a single SSPP/hwpipe, staged on both the Layer Mixers at
the same blend level. A plane that is greater than max width will comprise
of 2 SSPPs, with the 'left' SSPP staged on the left LM, and the 'right'
SSPP staged on the right LM at the same blend level.
For now, the drm_plane consists of only one SSPP, therefore, it
needs to be staged on both the LMs in blend_setup() and mdp5_ctl_blend().
We'll extend this logic to support 2 hwpipes per plane later.
The crtc cursor ops (using the LM cursors, not SSPP cursors) simply
return an error if they're called when the right mixer is assigned to
the CRTC state. With source split is enabled, we're expected to only
SSPP cursors.
This commit adds code that configures the right mixer, but the r_mixer
itself isn't assigned at the moment.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Some of the newer MDP5 versions support Source Split of SSPPs. It is a
feature that allows us to route the output of a hwpipe to 2 Layer
Mixers. This is required to achieve the following use cases:
- Dual DSI: For high res DSI panels (such as 2560x1600 etc), a single
DSI interface doesn't have the bandwidth to drive the required pixel
clock. We use 2 DSI interfaces to drive the left and right halves
of the panel (i.e, 1280x1600 each). The MDP5 pipeline here would look
like:
LM0 -- DSPP0 -- INTF1 -- DSI1
/
hwpipe--
\
LM1 -- DSPP1 -- INTF2 -- DSI2
A single hwpipe is used to scan out the left and right halves to DSI1
and DSI2 respectively. In order to do this, we need to configure the
2 Layer Mixers in Source Split mode.
- HDMI 4K: In order to support resolutions with width higher than the
max width supported by a hwpipe, we club 2 hwpipes together:
hwpipe1 --- LM0 -- DSPP0
- - \
- -- 3D Mux -- INTF0 -- HDMI
- - /
hwpipe2 --- LM1 -- DSPP1
hwpipe1 is staged on the 'left' Layer Mixer, and hwpipe2 is staged on
the 'right' Layer Mixer. An additional block called the '3D Mux' is
used to merge the output of the 2 DSPPs to a single interface.
In this use case, it is possible that a 4K surface is downscaled and
placed completely within one of the halves. In order to support such
scenarios (and keep the programming simple), Layer Mixers with Source
Split can be assigned 2 hw pipes per stage. While scanning out, the HW
takes care of fetching the pixels fom the correct pipe.
Add a MDP cap to tell whether the HW supports source split or not.
Add a MDP LM cap that tells whether a LM instance can operate in
source split mode (and generate the 'left' part of the display
output).
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
These are a part of CRTC state, it doesn't feel nice to leave them
hanging in mdp5_ctl struct. Pass mdp5_pipeline pointer instead
wherever it is needed.
We still have some params in mdp5_ctl like start_mask etc which
are derivative of atomic state, and should be rolled back if
a commit fails, but it doesn't seem to cause much trouble.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
In the last few commits, we've been adding params to mdp5_crtc_state, and
assigning them in the atomic_check() funcs. Now it's time to actually
start using them.
Remove the duplicated params from the mdp5_crtc struct, and start using
them in the mdp5_crtc code. The majority of the references to these params
is in code that executes after the atomic swap has occurred, so it's okay
to use crtc->state in them. There are a couple of legacy LM cursor ops that
may not use the updated state, but (I think) it's okay to live with that.
Now that we dynamically allocate a mixer to the CRTC, we can also remove
the static assignment to it in mdp5_crtc_init, and also drop the code that
skipped init-ing WB bound mixers (those will now be rejected by
mdp5_mixer_assign()).
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Things like vblank/err irq masks, mode of operation (command mode or not)
are derivative of the interface and mixer state. Therefore, they need to
be a part of the CRTC state too.
Add them to mdp5_crtc_state, and assign them in the CRTC's atomic_check()
func, so that it can be rolled back to a clean state.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
The INTF and CTL used in a display pipeline are going to be maintained as
a part of the CRTC state (i.e, in mdp5_crtc_state).
These entities, however, are currently statically assigned to drm_encoders
(i.e. mdp5_encoder). Since these aren't directly visible to the CRTC, we
assign them to the CRTC state in the encoder's atomic_check() op.
With this approach, we assign portions of CRTC state in two different
places: the layer mixer in CRTC's atomic_check(), and the INTF and CTL
pieces in the encoder's atomic_check() op.
We'd have more options here if the drm core maintained encoder state too,
but the current approach of clubbing everything in CRTC's state works just
fine.
Unlike hwpipes and mixers, we don't need to keep a track of INTF/CTL
assignments in the global atomic state. This is because they're currently
not sharable resources. For example, INTF0 and CTL0 will always be assigned
to one drm_encoder. This can change later when we implement writeback and
want a CRTC to use a CTL for a while, and then release it for others to use
it. Or, when a drm_encoder can switch between using a single INTF vs
2 INTFs.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Add the stuff needed to allow dynamically assigning a mixer to a CRTC.
Since mixers are a resource that can be shared across multiple CRTCs, we
need to maintain a 'hwmixer_to_crtc' map in the global atomic state,
acquire the mdp5_kms.state_lock modeset lock and so on.
The mixer is assigned in the CRTC's atomic_check() func, a failure will
result in the new state being cleanly rolled back.
The mixer assignment itself is straightforward, and almost identical to
what we do for hwpipes. We don't need to grab the old hwmixer_to_crtc
state like we do in hwpipes since we don't need to compare anything
with the old state at the moment.
The only LM capability we care about at the moment is whether the mixer
instance can be used to display stuff (i.e, connect to an INTF
downstream).
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Subclass drm_crtc_state so that we can maintain additional state for
our CRTCs.
Add mdp5_pipeline and mdp5_ctl pointers in the subclassed state.
mdp5_pipeline is a grouping of the HW entities that forms the downstream
pipeline for a particular CRTC. It currently contains pointers to
mdp5_interface and mdp5_hw_mixer tied to this CRTC. Later, we will
have 2 hwmixers in this struct. (We could also have 2 intfs if we want
to support dual DSI with Source Split enabled. Implementing that feature
isn't planned at the moment).
The mdp5_pipeline state isn't used at the moment. For now, we just
introduce mdp5_crtc_state and the crtc funcs needed to manage the
subclassed state.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
The mdp5_ctl has an 'op_mode' struct which contains info on
the downstream pipeline.
Grouping these params together in a struct doesn't serve much
purpose in the code. Maybe there was a plan to expand this
further that never happened.
Remove the op_mode struct, and place its members directly in
mdp5_ctl. This will help avoid confusion later when I introduce
my own verion of a mdp5 pipeline :)
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
mdp5_interface struct contains data corresponding to a INTF
instance in MDP5 hardware. This sturct is memcpy'd to the
mdp5_encoder struct, and then later to the mdp5_ctl struct.
Instead of copying around interface data, create mdp5_interface
instances in mdp5_init, like how it's done currently done for
pipes and layer mixers. Pass around the interface pointers to
mdp5_encoder and mdp5_ctl. This simplifies the code, and allows
us to decouple encoders from INTFs in the future if needed.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
PingPong ID for a Layer Mixer is already contained in
mdp5_hw_mixer.
This avoids the need to retrieve PP ID using macros
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Use the mdp5_hw_mixer struct in the mdp5_crtc and mdp5_ctl instead of
using the LM index.
Like before, the Layer Mixers are assigned statically to the CRTCs.
The hwmixer(s) will later be dynamically assigned to CRTCs.
For now, ignore the hwmixers that can only do WB.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Create a struct to represent MDP5 Layer Mixer instances. This will
eventually allow us to detach CRTCs from the Layer Mixers, and
generally clean things up a bit.
This is very similar to how hwpipes were previously abstracted away
from drm planes.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
The number of Layer Mixers and the downstream blocks (DSPPs and PPs)
connected to each LM can vary with different MDP5 revisions. These
parameters are also static.
Keep the per instance LM data in mdp5_cfg. This will avoid the need
to have macros which identify PP id or DSPP id the LM is connected
to. We don't configure DSPPs at the moment, but keeping the DSPP
instance # here might come handy later.
Also add a 'caps' field that identifies features supported by a
LM instance. Introduce the caps MDP_LM_CAP_DISPLAY and MDP_LM_CAP_WB
that identify whether a LM instance can be used for display or
writeback.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
We'd previously moved the pipe_lock spinlock to the hwpipe struct. Bring
it back to mdp5_plane. We will need this because an mdp5_plane in the
future could comprise of 2 hw pipes. It makes more sense to have a single
lock to protect the registers for the hw pipes used by a plane, rather
than trying to take individual locks per hwpipe when committing a
configuration.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
'SSPP_MAX + 1' is the max number of hwpipes that can be present on a
MDP5 platform. Recently, 2 new cursor hwpipes were added, which
caused overflows in arrays that used SSPP_MAX to represent the number
of elements. Update the SSPP_MAX value to incorporate the extra
hwpipes.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
A recent commit introduces a bug in dsi_mgr_phy_enable. In the non
dual DSI mode, we reset the mdsi (master DSI) PHY. This isn't right
since master and slave DSI exist only in dual DSI mode. For the normal
mode of operation, we should simply reset the PHY of the DSI device
(i.e. msm_dsi) corresponding to the current bridge.
Usage of the wrong DSI pointer also resulted in a static checker
warning. That too is resolved with this fix.
Fixes: b62aa70a98 (drm/msm/dsi: Move PHY operations out of host)
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Reviewed-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Rob Clark <robdclark@gmail.com>
'SSPP_MAX + 1' is the max number of hwpipes that can be present on a
MDP5 platform. Recently, 2 new cursor hwpipes were added, which
caused overflows in arrays that used SSPP_MAX to represent the number
of elements. Update the SSPP_MAX value to incorporate the extra
hwpipes.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
A recent commit introduces a bug in dsi_mgr_phy_enable. In the non
dual DSI mode, we reset the mdsi (master DSI) PHY. This isn't right
since master and slave DSI exist only in dual DSI mode. For the normal
mode of operation, we should simply reset the PHY of the DSI device
(i.e. msm_dsi) corresponding to the current bridge.
Usage of the wrong DSI pointer also resulted in a static checker
warning. That too is resolved with this fix.
Fixes: b62aa70a98 (drm/msm/dsi: Move PHY operations out of host)
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Reviewed-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Extend the DSI PHY/PLL drivers to support the DSI 14nm PHY/PLL
found on 8x96.
These are picked up from the downstream driver. The PHY part is similar
to the other DSI PHYs. The PLL driver requires some trickery so that
one DSI PLL can drive both the DSIs (i.e, dual DSI mode).
In the case of dual DSI mode. One DSI instance becomes the clock master,
and other the clock slave. The master PLL's output (Byte and Pixel clock)
is fed to both the DSI hosts/PHYs.
When the DSIs are configured in dual DSI mode, the PHY driver communicates
to the PLL driver using msm_dsi_pll_set_usecase() which instance is the
master and which one is the slave. When setting rate, the master PLL also
configures some of the slave PLL/PHY registers which need to be identical
to the master's for correct dual DSI behaviour.
There are 2 PLL post dividers that should have ideally been modelled as
generic clk_divider clocks, but require some customization for dual DSI.
In particular, when the master PLL's post-diviers are set, the slave PLL's
post-dividers need to be set too. The clk_ops for these use clk_divider's
helper ops and flags internally to prevent redundant code.
Cc: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
In case of dual DSI, some registers in PHY1 have been programmed
during PLL0 clock's set_rate. The PHY1 reset called by host1 later
will silently reset those PHY1 registers. This change is to reset
and enable both PHYs before any PLL clock operation.
[Originally worked on by Hai Li <hali@codeaurora.org>. Fixed up
by Archit Taneja <architt@codeaurora.org>]
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Create an init() op for dsi_phy which sets up things specific to
a given DSI PHY.
The dsi_phy driver probe expects every DSI version to get a
"dsi_phy_regulator" mmio base. This isn't the case for 8x96.
Creating an init() op will allow us to accommodate such
differences.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Add 8x96 DSI data in dsi_cfg. The downstream kernel's dsi_host driver
enables core_mmss_clk. We're seeing some branch clock warnings on
8x96 when enabling this. There doesn't seem to be any negative effect
with not enabling this clock, so use it once we figure out why we
get the warnings.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
The driver returns an error if a DSI DT node is populated, but no device
is connected to it or if the data-lane map isn't present. Ideally, such
a DSI node shouldn't be probed at all (i.e, its status should be set to
"disabled in DT"), but there isn't any harm in registering the DSI device
even if it doesn't have a bridge/panel connected to it.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
This code has been more or less picked up from the vc4 and intel
implementations of update_plane() funcs for cursor planes.
The update_plane() func is usually the drm_atomic_helper_update_plane
func that will issue an atomic commit with the plane updates. Such
commits are not intended to be done faster than the vsync rate.
The legacy cursor userspace API, on the other hand, expects the kernel
to handle cursor updates immediately.
Create a fast path in update_plane, which updates the cursor registers
and flushes the configuration. The fast path is taken when there is only
a change in the cursor's position in the crtc, or a change in the
cursor's crop co-ordinates. For anything else, we go via the slow path.
We take the slow path even when the fb changes, and when there is
currently no fb tied to the plane. This should hopefully ensure that we
always take a slow path for every new fb. This in turn should ensure that
the fb is pinned/prepared.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
In mdp5_plane_atomic_check, we get crtc_state from drm_plane_state.
Later, for cursor planes, we'll populate the update_plane() func that
takes a fast asynchronous path to implement cursor movements. There, we
would need to call a similar atomic_check func to validate the plane
state, but crtc_state would need to be derived differently.
Refactor mdp5_plane_atomic_check to mdp5_plane_atomic_check_with_state
such that the latter takes crtc_state as an argument.
This is similar to what the intel driver has done for async cursor
updates.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Register cursor drm_planes. The loop in modeset_init that inits the
planes and crtcs has to be refactored a bit. We first iterate all the
hwpipes to find the cursor planes. Then, we loop again to create
crtcs.
In msm_atomic_wait_for_commit_done, remove the check which bypasses
waiting for vsyncs if state->legacy_cursor_updates is true.
We will later create a fast path for cursor position changes in the
cursor plane's update_plane func that doesn't go via the regular
atomic commit path. For rest of cursor related updates, we will have
to wait for vsyncs, so ignore the legacy_cursor_updates flag.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
These are various changes added in preparation for cursor planes:
- Add a pipe_cursor block for 8x96 in mdp5_cfg.
- Add a new pipe CAP called MDP_PIPE_CAP_CURSOR. Use this to ensure we
assign a cursor SSPP for a drm_plane with type DRM_PLANE_TYPE_CURSOR.
- Update mdp5_ctl_blend_mask/ext_blend_mask funcs to incorporate cursor
SSPPs.
- In mdp5_ctl_blend, iterate through MAX_STAGES instead of stage_cnt,
we need to do this because we can now have empty stages in between.
- In mdp5_crtc_atomic_check, make sure that the cursor plane has the
highest zorder, and stage the cursor plane to the maximum stage #
present on the HW.
- Create drm_crtc_funcs that doesn't try to implement cursors using the
older LM cursor HW.
- Pass drm_plane_type in mdp5_plane_init instead of a bool telling
whether plane is primary or not.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
In MDP5 Layer Mixer HW, the blender output is only the blended color
components (i.e R, G and B, or COLOR0/1/2 in MDP5 HW terminology). This
is fed to the BG input of the next blender. We also need to provide an
alpha (COLOR3) value for the BG input at the next stage.
This is configured via using the REG_MDP5_LM_BLEND_COLOR_OUT register.
For each stage, we can propagate either the BG or FG alpha to the next
stage.
The approach taken by the driver is to propagate FG alpha, if the plane
staged on that blender has an alpha. If it doesn't, we try to propagate
the base layer's alpha.
This is borrowed from downstream MDP5 kernel driver. Without this, we
don't see any cursor plane content.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
The MDP5 plane's atomic_check ops doesn't perform clipping tests.
This didn't hurt us much in the past, but clipping becomes important
with cursor planes.
Use drm_plane_helper_check_state, the way rockchip/intel/mtk drivers
already do. Use these drivers as reference.
Clipping requires knowledge of the crtc width and height. This requires
us to call drm_atomic_helper_check_modeset before
drm_atomic_helper_check_planes in the driver's atomic_check op, because
check_modetest will populate the mode for the crtc, needed to populate
the clip rectangle.
We update the plane_enabled(state) local helper to use state->visible,
since state->visible and 'state->fb && state->crtc' represent the same
thing.
One issue with the existing code is that we don't have a way to disable
the plane when it's completely clipped out. Until there isn't an update
on the crtc (which would de-stage the plane), we would still see the
plane in its last 'visible' configuration.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Use SSPP_NONE in mdp5_plane_pipe() if there is now hwpipe allocated for
the drm_plane. Returning '0' means we are returning VIG0 pipe.
Also, use the mdp5_pipe enum to pass around the stage array. Initialize
the stage to SSPP_NONE by default.
We do the above because 1) Cursor plane has to be staged at the topmost
blender of the LM, which can result in empty stages in between 2) In
the future, when we support multiple LMs per CRTC. We could have stages
which don't have any pipe assigned to them.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
We currently create CRTCs equaling to the # of Layer Mixer blocks we
have on the MDP5 HW. This number is generally more than the # of encoders
(INTFs) we have in the MDSS HW. The number of encoders connected to
displays on the platform (as described by DT) would be even lesser.
Create only N drm_crtcs, where N is the number of drm_encoders
successfully registered. To do this, we call modeset_init_intf() before
we init the drm_crtcs and drm_planes.
Because of this change, setting encoder->possible_crtcs needs to be moved
from construct_encoder() to a later point when we know how many CRTCs we
have.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Count can't be non-zero. Changing to uint will also prevent future
warnings.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
For the DSI interfaces, the mdp5_kms core creates 2 encoders for video
and command modes.
Create only a single encoder per interface. When creating the encoder, set
the interface type to MDP5_INTF_MODE_NONE. It's the bridge (DSI/HDMI/eDP)
driver's responsibility to set a different interface type. It can use the
the kms func op set_encoder_mode to change the mode of operation, which
in turn would configure the interface type for the INTF.
In mdp5_cmd_encoder.c, we remove the redundant code, and make the commmand
mode funcs as helpers that are used in mdp5_encoder.c
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Rename the mdp5_encoder_* ops for active displays to
mdp5_vid_encoder_* ops.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
The mdp5 kms driver currently sets up multiple encoders per interface
(INTF), one for each kind of mode of operation it supports.
We create 2 drm_encoders for DSI, one for Video Mode and the other
for Command Mode operation. The reason behind this approach could have
been that we aren't aware of the DSI device's mode of operation when
we create the encoders.
This makes things a bit complicated, since these encoders have to
be further attached to the same DSI bridge. The easier way out is
to create a single encoder, and make the DSI driver set its mode
of operation when we know what the DSI device's mode flags are.
Start with providing a way to set the mdp5_intf_mode using a kms
func that sets the encoder's mode of operation. When constructing
a DSI encoder, we set the mode of operation to Video Mode as
default. When the DSI device is attached to the host, we probe the
DSI mode flags and set the corresponding mode of operation.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
We currently create 2 encoders for DSI interfaces, one for command
mode and other for video mode operation. This isn't needed as we
can't really use both the encoders at the same time. It also makes
connecting bridges harder.
Switch to creating a single encoder. For now, we assume that the
encoder is configured only in video mode. Later, the same encoder
would be usable in both modes.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
The commit "drm: bridge: Link encoder and bridge in core code" updated
the drm_bridge_attach() API to also include the drm_encoder pointer
the bridge attaches to.
The func msm_dsi_manager_bridge_init() now relies on the drm_encoder
pointer stored in msm_dsi->encoders to pass the encoder to the bridge
API.
msm_dsi->encoders is unfortunately set after this function is called,
resulting in us passing a NULL pointer to drm_brigde_attach. This
results in an error and the DSI driver probe fails.
Move the initialization of msm_dsi->encoders[] a bit up. Also, don't
try to set the encoder's bridge. That's now managed by the bridge
API.
Cc: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Define the block in advance so that the generated mdp5.xml.h doesn't
break build.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Archit Taneja