After _gadget_stop_activity is executed, we can consider the hardware
operation for gadget has finished, and the udc can be stopped and enter
low power mode. So, any later hardware operations (from usb_ep_ops APIs
or usb_gadget_ops APIs) should be considered invalid, any deinitializatons
has been covered at _gadget_stop_activity.
I meet this problem when I plug out usb cable from PC using mass_storage
gadget, my callstack like: vbus interrupt->.vbus_session->
composite_disconnect ->pm_runtime_put_sync(&_gadget->dev),
the composite_disconnect will call fsg_disable, but fsg_disable calls
usb_ep_disable using async way, there are register accesses for
usb_ep_disable. So sometimes, I get system hang due to visit register
without clock, sometimes not.
The Linux Kernel USB maintainer Alan Stern suggests this kinds of solution.
See: http://marc.info/?l=linux-usb&m=138541769810983&w=2.
Cc: <stable@vger.kernel.org> #v4.9+
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Link: https://lore.kernel.org/r/20190820020503.27080-2-peter.chen@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
At imx7ulp, the USB related analog register is located in PHY register
region too, so we need to control PLL at PHY driver directly.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Enable USBOTG1 support for evk board, it is dual-role function
port.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
An endpoint conflict occurs when the USB is working in device mode
during an isochronous communication. When the endpointA IN direction
is an isochronous IN endpoint, and the host sends an IN token to
endpointA on another device, then the OUT transaction may be missed
regardless the OUT endpoint number. Generally, this occurs when the
device is connected to the host through a hub and other devices are
connected to the same hub.
The affected OUT endpoint can be either control, bulk, isochronous, or
an interrupt endpoint. After the OUT endpoint is primed, if an IN token
to the same endpoint number on another device is received, then the OUT
endpoint may be unprimed (cannot be detected by software), which causes
this endpoint to no longer respond to the host OUT token, and thus, no
corresponding interrupt occurs.
There is no good workaround for this issue, the only thing the software
could do is numbering isochronous IN from the highest endpoint since we
have observed most of device number endpoint from the lowest.
Cc: <stable@vger.kernel.org> #v3.14+
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Greg KH <gregkh@linuxfoundation.org>
Cc: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Cc: Jun Li <jun.li@nxp.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since the chipidea common code support get the USB PHY phandle from
"phys", the glue layer is not mandatory to get the "fsl,usbphy" phandle
any more.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
In this commit, we add CI_HDRC_PMQOS to avoid system entering idle,
at imx7ulp, if the system enters idle, the DMA will stop, so the USB
transfer can't work at this case.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
The calculation of packet number within microframe is different between
high-speed and super-speed endpoint, we add support for super-speed
in this patch.
Cc: Pawel Laszczak <pawell@cadence.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
For USB HSIC, the data and strobe pin needs to be pulled down
at default, we consider it as "idle" state. When the USB host
is ready to be used, the strobe pin needs to be pulled up,
we consider it as "active" state.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
The chipidea controller has some special requirements during
suspend/resume, override common ehci->hub_control to implement
it.
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Tested-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
To support imx HSIC, there are some special requirement:
- The HSIC pad is 1.2v, it may need to supply from external
- The data/strobe pin needs to be pulled down first, and after
host mode is initialized, the strobe pin needs to be pulled up
- During the USB suspend/resume, special setting is needed
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Tested-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
The TPL support is used to identify targeted devices during
EH2.0 and EH3.0 certification test, the user can add "tpl-support"
at dts to enable this feature.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The commit 4e88d4c083 ("usb: add a flag to skip PHY
initialization to struct usb_hcd") delete the assignment
for hcd->usb_phy, it causes usb_phy_notify_connect{disconnect)
are not called, the USB PHY driver is not notified of hot plug
event, then the disconnection will not be detected by hardware.
Fixes: 4e88d4c083 ("usb: add a flag to skip PHY initialization
to struct usb_hcd")
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reported-by: Mats Karrman <mats.dev.list@gmail.com>
Tested-by: Mats Karrman <mats.dev.list@gmail.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
The port->logbuffer_head may be wrong if the two processes enters
_tcpm_log at the mostly same time. The 2nd process enters _tcpm_log
before the 1st process update the index, then the 2nd process will
not allocate logbuffer, when the 2nd process tries to use log buffer,
the index has already updated by the 1st process, so it will get
NULL pointer for updated logbuffer, the error message like below:
tcpci 0-0050: Log buffer index 6 is NULL
Cc: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Jun Li <jun.li@nxp.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This issue is detected when the system has another device driver
which registers USB connector extcon device, fix it by adding
extcon device check.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
The controller driver may be NULL if the controller device
is the middle device between platform device and roothub.
This middle device may not need a device driver due to all
hardware control can be at platform device driver, this
platform device is usually a dual-role USB controller device.
The benefit of using this middle device is we can keep both
controller device's private data (known as struct usb_hcd)
for USB core use, and platform device's private data for
platform driver use.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Both xhci_hub_control and xhci_disable_slot tries to hold spinlock, the
spinlock recursion occurs when enters USB2 test mode. Fix it by unlock
spinlock before calling xhci_disable_slot.
Cc: <stable@vger.kernel.org>
Fixes: 0f1d832ed1 ("usb: xhci: Add port test modes support for usb2")
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
According to xHCI spec Figure 30: Interrupt Throttle Flow Diagram
If PCI Message Signaled Interrupts (MSI or MSI-X) are enabled,
then the assertion of the Interrupt Pending (IP) flag in Figure 30
generates a PCI Dword write. The IP flag is automatically cleared
by the completion of the PCI write.
the MSI enabled HCs don't need to clear interrupt pending bit, but
hcd->irq = 0 doesn't equal to MSI enabled HCD. At some Dual-role
controller software designs, it sets hcd->irq as 0 to avoid HCD
requesting interrupt, and they want to decide when to call usb_hcd_irq
by software.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
According to xHCI ch4.20 Scratchpad Buffers, the Scratchpad
Buffer needs to be zeroed.
...
The following operations take place to allocate
Scratchpad Buffers to the xHC:
...
b. Software clears the Scratchpad Buffer to '0'
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We already have sp_array to store each scratch buffer address for xHC,
it doesn't need another sp_dma_buffers array to store it.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Sometimes, the user needs to adjust some properties for controllers, eg
the role for controller, we add sysfs group for them.
The attribute 'role' is used to switch host/gadget role dynamically, the
uewr can read the current role, and write the other role compare to
current one to finish the switch.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Whether the USB port as a wakeup source should be determined by user,
but not enabled by default.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
There are only two requests for uac2, it may not be enough at high
loading system which usb interrupt handler can't be serviced on
time, then the data will be lost since it is isoc transfer for audio.
In this patch, we introduce a parameter for the number for usb request,
and the user can override it if current number for request is not enough
for his/her use case.
Besides, update this parameter for legacy audio gadget and documentation.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
At some situations, the vbus may already be there before starting
gadget. So we need to check vbus event after switching to gadget in
order to handle missing vbus event. The typical use cases are plugging
vbus cable before driver load or the vbus has already been there
after stopping host but before starting gadget.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Tested-by: Stephen Boyd <stephen.boyd@linaro.org>
Reported-by: Stephen Boyd <stephen.boyd@linaro.org>
At some systems, the pinctrl setting will be lost or needs to
set as "sleep" state to save power consumption. So, we need to
configure pinctrl as "sleep" state when system enters suspend,
and as "default" state after system resumes. In this way, the
pinctrl value can be recovered as "default" state after resuming.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
The USB core may call reset_resume when it fails to resume asix device.
And USB core can recovery this abnormal resume at low level driver,
the same .resume at asix driver can work too. Add .reset_resume can
avoid disconnecting after backing from system resume, and NFS can
still be mounted after this commit.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add clock operation at .set_suspend if the PHY has
suspend requirement, it can be benefit of power saving for
phy and the whole system (parent clock may also be disabled).
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
For isoc endpoint descriptor, the wMaxPacketSize is not real max packet
size (see Table 9-13. Standard Endpoint Descriptor, USB 2.0 specifcation),
it may contain the number of packet, so the real max packet should be
ep->desc->wMaxPacketSize && 0x7ff.
Cc: Felipe F. Tonello <eu@felipetonello.com>
Cc: Felipe Balbi <felipe.balbi@linux.intel.com>
Fixes: 16b114a6d7 ("usb: gadget: fix usb_ep_align_maybe
endianness and new usb_ep_aligna")
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
It is the 10th processor in the well-known imx6 series, and derived
from imx6ul but cost optimized. The more information about imx6ull
can be found at:
http://www.nxp.com/products/microcontrollers-and-processors/
arm-processors/i.mx-applications-processors/i.mx-6-processors
/i.mx6qp/i.mx-6ull-single-core-processor-with-arm-cortex-a7-core
:i.MX6ULL
imx6ul.dtsi is the SoC common stuff for both imx6ul and imx6ull;
imx6ul-14x14-evk.dts is the board common stuff for both imx6ul
and imx6ull 14x14 evk. In this patch, for SoC part, the
imx6ull.dtsi includes imx6ul.dtsi; for board part, imx6ull-14x14-evk.dts
includes imx6ul-14x14-evk.dts.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
We need to change trimming value (as a percentage) of the 17.78mA TX
reference current for better signal quality. With this change, we
can pass the eye-diagram test on this board.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
We need to change trimming value (as a percentage) of the 17.78mA TX
reference current for better signal quality. With this change, we
can pass the eye-diagram test on this board.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
With commit 851ce93224 ("usb: chipidea: otg: don't wait vbus
drops below BSV when starts host"), the driver can support
enabling vbus output without software control, so this board
(control vbus output through ID pin) can support dual-role now.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
of_node_put needs to be called when the device node which is got
from of_parse_phandle has finished using.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Since ulpi bus driver is located at usb/common/ulpi.c, whether it
is compiled or not depends on CONFIG_USB_COMMON which needs either
USB Host or USB Gadget is enabled, so even CONFIG_USB_ULPI_BUS is
chosen, its source may still not be compiled when both USB HOST
and USB gadget are disabled.
It fixed compile error with below configurations:
- # CONFIG_USB is not set
- # CONFIG_USB_GADGET is not set
- CONFIG_PHY_TUSB1210=m
- CONFIG_USB_ULPI_BUS=m
>> All errors (new ones prefixed by >>):
>>
>> ERROR: "ulpi_unregister_driver" [drivers/phy/phy-tusb1210.ko] undefined!
>> ERROR: "__ulpi_register_driver" [drivers/phy/phy-tusb1210.ko] undefined!
>> ERROR: "ulpi_write" [drivers/phy/phy-tusb1210.ko] undefined!
Fixes: ad764c49f6 ("usb: Kconfig: move ulpi bus support out of host")
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In eth_start_xmit, the socket buffer may be NULL. So, add NULL pointer
check at .wrap API.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
In eth_start_xmit, the socket buffer may be NULL. So, add NULL pointer
check at .wrap API.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
At imx6ul_init_machine, it calls imx6ul_pm_init which needs to find
platform device for ocram, but the default populate platform device is at
of_platform_default_populate_init, which is located at arch_initcall_sync,
and called later than arch_initcall (.init_machine is located at that).
So below warning message will be showed during boots up:
imx6q_suspend_init: failed to find ocram device!
imx6_pm_common_init: No DDR LPM support with suspend -19!
Due to lack of ocram device, the suspend mode "mem" which needs ocram to
store suspend routine code is invalid.
This commit populates platform device before imx6ul_pm_init like other
imx6 platforms do, and the suspend mode "mem" can work successfully.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Fixes: 850bea2335 ("arm: Remove unnecessary of_platform_populate with default match table")
Cc: Anson Huang <anson.huang@nxp.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Kefeng Wang <wangkefeng.wang@huawei.com>
Cc: Rob Herring <robh@kernel.org>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
There is a missing BM_CLPCR_BYP_MMDC_CH0_LPM_HS setting for imx6ul,
without it, the "standby" mode can't work well, the system can't be
resumed.
With this commit, the "standby" mode works well.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Cc: Anson Huang <anson.huang@nxp.com>
Cc: <stable@vger.kernel.org>
Fixes: ee4a5f838c ("ARM: imx: add suspend/resume support for i.mx6ul")
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The udc device needs to be deleted if error occurs
Fixes: 855ed04a37 ("usb: gadget: udc-core: independent registration of
gadgets and gadget drivers")
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
For case 14 and case 21, their correct return value is the number
of bytes transferred, so it is a positive integer. But in usbtest_ioctl,
it takes non-zero as false return value for usbtest_do_ioctl, so
it will treat the correct test as wrong test, then the time on
tests will be the minus value.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Cc: stable <stable@vger.kernel.org>
Fixes: 18fc4ebdc7 ("usb: misc: usbtest: Remove timeval usage")
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
dev->port_usb is checked for null pointer at above code, so dev->port_usb
might be null, fix it by adding null pointer check.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
cdev->config is checked for null pointer at above code, so cdev->config
might be null, fix it by adding null pointer check.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
For case 14 and case 21, their correct return value is the number
of bytes transferred, so it is a positive integer. But in usbtest_ioctl,
it takes non-zero as false return value for usbtest_do_ioctl, so
it will treat the correct test as wrong test, then the time on
tests will be the minus value.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Cc: stable <stable@vger.kernel.org>
Fixes: 18fc4ebdc7 ("usb: misc: usbtest: Remove timeval usage")
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
- USB test module
- USB gadget functions using configfs which are just ready within
several release cycles.
- USB audio gadget
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
of_node_put needs to be called when the device node which is got
from of_parse_phandle has finished using it.
Besides, of_address_to_resource always returns -EINVAL for error, delete
the assignment for ret.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
of_node_put needs to be called when the device node which is got
from of_parse_phandle has finished using.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
of_node_put needs to be called when the device node which is got
from of_parse_phandle has finished using.
This commit fixes both local (in stmmac_axi_setup) and global
(plat->phy_node) device_node for this issue, and using the
correct device node when tries to put node at stmmac_probe_config_dt
for error path.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
of_node_put needs to be called when the device node which is got
from of_parse_phandle has finished using.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
of_node_put needs to be called when the device node which is got
from of_parse_phandle has finished using.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
of_node_put needs to be called when the device node which is got
from of_parse_phandle has finished using.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
of_node_put needs to be called when the device node which is got
from of_parse_phandle has finished using.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
of_node_put needs to be called when the device node which is got
from of_parse_phandle has finished using.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
of_node_put needs to be called when the device node which is got
from of_parse_phandle has finished using.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
of_node_put needs to be called when the device node which is got
from of_parse_phandle has finished using.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
of_node_put needs to be called when the device node which is got
from of_parse_phandle has finished using.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
of_node_put needs to be called when the device node which is got
from of_parse_phandle has finished using.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
of_node_put needs to be called when the device node which is got
from of_parse_phandle has finished using.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
of_node_put needs to be called when the device node which is got
from of_parse_phandle (or of_node_get) has finished using.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
of_node_put needs to be called when the device node which is got
from of_parse_phandle has finished using.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
[rebased on top of Archit's DT rework, so looses one hunk]
Signed-off-by: Rob Clark <robdclark@gmail.com>
of_node_put needs to be called when the device node which is got
from of_parse_phandle has finished using, but current code only
calls it at error path, fix it by adding it at correct code path.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Stefan Agner <stefan@agner.ch>
of_node_put needs to be called when the device node which is got
from of_parse_phandle has finished using.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
of_node_put needs to be called when the device node which is got
from of_parse_phandle has finished using.
Cc: Alexey Brodkin <abrodkin@synopsys.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
of_node_put needs to be called when the device node which is got
from of_parse_phandle has finished using.
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
of_node_put needs to be called when the device node which is got
from of_parse_phandle has finished using.
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
of_node_put needs to be called when the device node which is got
from of_parse_phandle has finished using.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Peter Chen