In cases where PHY register access is not supported, don't mislead
a caller into thinking that it is supported by returning a PHY
address. Instead, return -EOPNOTSUPP when PHY access is not
supported.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The thermal sensor event logic is messed up, because it can execute
the code when there is no thermal event. The current logic is that
it will exit when !capable && !event whereas it really should exit
when !capable || !event. For one thing, it means that the service
task is doing too much work. It probably has some other symptoms as
well. So, correct the logic, simplifying to only execute when there
is a thermal event. The capable check is redundant.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There are two problems with EEPROM access. One is that it needs to
hold the semaphore until the entire response is read or else the
response can be corrupted by other firmware accesses. The second
problem is that acquiring and releasing the semaphore is slow, so
it should be taken and released once when multiple EEPROM accesses
will be done.
Both of these issues can be solved by adding a new function,
ixgbe_hic_unlocked, to issue firmware commands that will assume
that the caller has acquired the needed semaphore.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The msix_entries memory can be freed by a previous suspend or
remove, so don't crash on close when it isn't there. Also only
clear the interrupts when the interface is up, because there
aren't any when it is not up.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
All the MACs supported by ixgbe support pause frames, so indicate
that support in ethtool. Also set advertising according to requested
mode.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Somehow the wrong fc_setup function was used for x550em_a, so
correct that. Also set setup_link to NULL as its value is
determined later, just like it is with X550EM_x.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Use a new register to wait for previous register writes to complete
before issuing a register read. This is needed when slower links
are in use.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add support for x550em_a 10G MAC type to the ixgbe driver. The new
MAC includes new firmware commands that need to be used to control
PHY and IOSF access, so that support is also added. The interface
supported is a native SFP+ interface.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We need to take the manageability semaphore when issuing firmware
commands to avoid problems. With this in place, the semaphore is
no longer taken in the ixgbe_set_fw_drv_ver_generic function, since
it will now always be taken by the ixgbe_host_interface_command
function.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Clean up the interface for issuing firmware commands to use a
void * instead of a u32 *. This eliminates a number of casts.
Also clean up ixgbe_host_interface_command in a few other ways,
eliminating comparisons with 0, redundant parens and minor
formatting issues.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The function ixgbe_host_interface_command actually uses a multiple
of word sized buffer to do its business, but only checks against
the actual length passed in. This means that on read operations it
could be possible to modify locations beyond the length passed in.
Change the check to round up in the same way, just to avoid any
possible hazard.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Xeon D KR backplane is different from other backplanes,
in that we can't use auto-negotiation to determine the
mode. Instead, use whatever the user configured.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The source for the ops structure contents are const, so make them
so. Copy them in place with structure assignments instead of memcpys.
Make the mbx_ops accessed by reference instead of making a copy of
the source structure. Update copyright date on the touched files.
Reported-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Right now ATR is not handling IPv6 extended headers, so ATR is not
being performed on such packets. Fix that by skipping extended
headers when they are present. This also fixes a problem where
the ATR code was not checking that the inner protocol was actually
TCP before setting up the signature rules. Since the protocol check
is intimately involved with the extended header processing as well,
this all gets fixed together.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If an outer UDP checksum is set, pass the skb up with CHECKSUM_NONE
so that the stack will check the checksum. Do not increment an
error counter, because we don't know that there is an actual error.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The X550EM_x revision check needs to check a value, not just a bit.
Use a mask and check the value. Also remove the redundant check
inside the ixgbe_enter_lplu_t_x550em, because it can only be called
when both the mac type and revision check pass.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Clean up minor redundancy in the setting of hw_enc_features that
makes it appears that X550 uniquely has more encapsulation features
than other devices. The driver only supports one more feature, so
make it look that way. No longer set NETIF_F_SG since that is set
by the register_netdev call. Thanks to Alex Duyck for noticing this
slight confusion.
Reported-by: Alexander Duyck <aduyck@mirantis.com>
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Check for and handle IPv6 extended headers so that Tx checksum
offload can be done. Also use skb_checksum_help for unexpected
cases. Thanks to Tom Herbert for noticing these problems. Thanks
to Alexander Duyck for seeing how to coalesce the error handling
into one location.
Reported-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Darin Miller <darin.j.miller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Instead of inhibiting PHY power control when manageability is
present, only inhibit turning PHY power off when manageability
is present. Consequently, PHY power will always be turned on when
requested. Without this patch, some systems with X540 or X550
devices in some conditions will never get link.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Check for and handle IPv6 extended headers so that Tx checksum
offload can be done. Also use skb_checksum_help for unexpected
cases. Thanks to Tom Herbert for noticing these problems. Thanks
to Alexander Duyck for recognizing problems with the first version
of this patch and recognizing how to coalesce error conditions
into a single location.
Reported-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Save VF device pointers and take references to speed accesses used
to monitor the device behavior to avoid slot resets. The saved
information avoids lock contention during the search used to access
each of the VFs.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Darin Miller <darin.j.miller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The ixgbe driver was violating the specification in the datasheet
by not waiting 1ms before checking for the reset bit clearing. This
is called out for devices supported by ixgbe, so implement the
required delay.
Reported-by: Dan Streetman <dan.streetman@canonical.com>
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Darin Miller <darin.j.miller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The X550EM_x devices handle clocking differently, so update the
PTP implementation to accommodate them. This involves significant
changes to ixgbe's PTP code to accommodate the new range of
behaviors including things like non-power-of-2 clock wrapping.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Darin Miller <darin.j.miller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Make some minor cleanups, such as simplifying return paths, deleting
unneeded initializations, return values more directly and so forth.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Darin Miller <darin.j.miller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Use a private workqueue to avoid hangs that were otherwise possible
when performing stress tests, such as creating and destroying many
VFS repeatedly.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Darin Miller <darin.j.miller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Use a private workqueue to avoid hangs that were otherwise possible
when performing stress tests, such as creating and destroying many
VFS repeatedly.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Darin Miller <darin.j.miller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The newer copper PHY implementation used with newer X550EM_x
devices uses a different thermal alarm type than the earlier
one. Make changes to support both types.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Darin Miller <darin.j.miller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch removes KR PHY reset from ixgbe_init_phy_ops_x550em,
since this function is meant to initialize function pointers for
the detected PHY type. Internal PHY reset was moved to
ixgbe_setup_internal_phy_t_x550em which will now detect which
mode the internal PHY operates in and set it up as required.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Darin Miller <darin.j.miller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If the reset never completes, it is necessary to retake the
semaphore before returning, because the caller will release
the semaphore.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Darin Miller <darin.j.miller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
With the addition of X550em_x SFP+ support, the driver is now
functionally equivalent to what will be the 4.2.1 driver when
released, so change the version to match.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The X540 thermal interrupt (IXGBE_EIMS_TS) is not an SDP, so it
doesn't need to be enabled in ixgbe_setup_gpie(). In fact the
value is simply not for the GPIE register at all.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The 82599 and X540 datasheets require that FCRTH be "set" for Tx
switching (VM-to-VM loopback) but it did not previously specify what
the value should be set to. It has now been determined that
the correct value is RXPBSIZE - (24*1024).
This setting is also required for later devices.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
A logic error here results in the adapter_stopped flag only being
cleared when ixgbe_setup_fc returns an error. Correct the logic.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change does two things. First, it makes it so that we always
set the relaxed ordering bits related to the DCA registers even if
DCA is not enabled. Second, it moves the configuration out of the
ixgbe_down function and into the ixgbe_configure function before
enabling the Rx and Tx rings. This ensures that DCA is configured
correctly before starting to process packets.
Thanks to Alex Duyck for this fix.
CC: Alex Duyck <aduyck@mirantis.com>
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch skips the PCI transactions pending check in
ixgbe_disable_pcie_master. This is done to addresses a known HW
issue where the PCI transactions pending bit sticks high when there
are pending transactions. HW engineering instructed to workaround
this issue by wait and then continue with our reset flow.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Take control of an I2C mux that selects which SFP is attached to
the I2C bus. The control of the mux is captured in the taking and
releasing of the related semaphore. Because only port 1 can control
the mux, port 1 always leaves the mux set to select port 0.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Reduce the frequency of polling for SFP modules. Because the
service task sometimes runs at high rates, we can poll for
SFPs too often. When an SFP is not present, the I2C timeouts
that result are very costly. So, prevent SFP polling from
being done more than once every two seconds. To reduce latency,
the poll time is cleared in a couple of cases to permit the
next service task execution to poll the SFP module.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Configures the CS4227 correctly for both 1G and 10G operation,
by moving the code to ixgbe_setup_mac_link_sfp_x550em(). It
needs to be in this function because we need both the module
type and the speed, and this is the only function in the init
flow that knows the speed. In contrast,
ixgbe_setup_sfp_modules_X550em() does not know the speed, so we
can't do anything useful here. This is a fundamental difference
from the previous flow, and is due to the way the CS4227 is
implemented.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds X550EM_x SFP+ dual-speed support. 82599 fiber link
code was moved from ixgbe_82599.c to ixgbe_common.c for use by
X550EM. SFP MAC link code is added to x550EM.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Reduce the number of retries during PHY detection. This reduces
pauses when no SFP is present. Once an SFP is detected, the normal
retry count will be used.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Clear the destination location for I2C data initially so that
the received data will not be affected by previous attempts.
This could have returned wrong data in certain retry sequences.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Set the bit banging mode in the hardware when performing bit banging
I2C operations on X550. Also control the output enable on both the
clock and data lines.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The lan_id is being set after a previous I2C eeprom access which
makes no sense because it needs to be set before any access. Move
the setting to before the access.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Most I2C accesses take and release semaphores for each access. Now
there is a reason to perform multiple I2C operations under the same
holding of the semaphore, so provide unlocked I2C methods for that
purpose.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When an SFP not present error is returned by the reset_hw method,
accept it and go on, since an SFP can still be inserted. Previously
it was only accepted for 82598 devices.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Now that we can do 2.5G link speed, we need to be able to report it.
Also change the nested triadic involved in creating the log message
to instead use a simpler switch statement to set a string pointer.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Avoid a needless PHY access on copper phys to save the 10ms wait
time for each PHY access. A helper function is introduced to
actually do the register access and process the contents.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
By using GSO for UDP-encapsulated packets, all ixgbe devices can
be directed to generate checksums for the inner headers because
the outer UDP checksum can be zero. So point the machinery at the
inner headers and have the hardware generate the checksum.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Simplify port-specific macros by eliminating explicit comparison
with 0. More importantly, enclose formal parameter in parens to
eliminate the risk of an operator precedence surprise.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Set the PCI_DEV_FLAGS_VPD_REF_F0 flag on all Intel Ethernet device
functions other than function 0, so that on multi-function devices, we will
always read VPD from function 0 instead of from the other functions.
[bhelgaas: changelog]
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Alexander Duyck <alexander.h.duyck@redhat.com>
CC: stable@vger.kernel.org
Add a dev_flags bit, PCI_DEV_FLAGS_VPD_REF_F0, to access VPD through
function 0 to provide VPD access on other functions. This is for hardware
devices that provide copies of the same VPD capability registers in
multiple functions. Because the kernel expects that each function has its
own registers, both the locking and the state tracking are affected by VPD
accesses to different functions.
On such devices for example, if a VPD write is performed on function 0,
*any* later attempt to read VPD from any other function of that device will
hang. This has to do with how the kernel tracks the expected value of the
F bit per function.
Concurrent accesses to different functions of the same device can not only
hang but also corrupt both read and write VPD data.
When hangs occur, typically the error message:
vpd r/w failed. This is likely a firmware bug on this device.
will be seen.
Never set this bit on function 0 or there will be an infinite recursion.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Alexander Duyck <alexander.h.duyck@redhat.com>
CC: stable@vger.kernel.org
Because error codes are negative, it only makes sense to
consistently use signed types when handling them. Also remove
some explicit comparisons with 0 on these variables.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
IOSF is the Intel On-chip System Fabric used in SOCs. IOSF SB is
the IOSF SideBand message interface. This patch serializes IOSF SB
access using both phy bits in the SWFW_SEMAPHORE register. It also
adds a helper function to wait for IOSF SB accesses to complete.
Use the new function to perform this wait before each access, as
specified in the datasheet, in addition to using it to wait for
IOSF SB read/write completion.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Resolve some missing-field-initializers warnings by using
designated initialization.
[hch: W=2 with modern gcc warns about this. Pretty pointless to me, but
I'd prefer to keep us warning free]
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Resolve "logical 'and' applied to non-boolean constant" warnings"
that appear in W=2 builds by adding !! to a bit test.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Resolve some shadow warnings produced in W=2 builds by changing the name
of some parameters and local variables. Change instances of "s64"
because that clashes with the well-known typedef. Also change a local
variable with the name "up" because that clashes with the name of of the
"up" function for semaphores. These are hazards so eliminate the
hazards by renaming them.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Resolve shadow warnings that are produced in W=2 builds by renaming a
global with a too-generic name and renaming a formal parameter.
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
It is a really bad idea to declare variables or parameters that
have the same name as common types. It is valid C, but it gets
surprising if a macro expansion attempts to declare an inner
local with that type. Change the local names to eliminate the
hazard.
Change s16 => str16, s8 => str8.
This resolves warnings seen when using W=2 during make, for instance:
drivers/firmware/efi/vars.c: In function ‘dup_variable_bug’:
drivers/firmware/efi/vars.c:324:44: warning: declaration of ‘s16’ shadows a global declaration [-Wshadow]
static void dup_variable_bug(efi_char16_t *s16, efi_guid_t *vendor_guid,
drivers/firmware/efi/vars.c:328:8: warning: declaration of ‘s8’ shadows a global declaration [-Wshadow]
char *s8;
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
If a hardware Tx timestamp is requested, an uninitialized
workqueue entry may be scheduled, especially on an 82598 adapter.
Add a check for a PTP clock to avoid that. Also only apply the
unlikely to the first term of the conditional. That will make the
rest of the checks be in the cold path.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Acked-by: Matthew Vick <matthew.vick@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Mark D Rustad