pm_runtime_autosuspend_expiration calls ktime_get_mono_fast_ns()
even when its returned value may be unused. Therefore get the
current time later and remove gotos while there.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Vincent Guittot <vincent.guittot@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
PM-runtime now uses the hrtimers infrastructure for autosuspend, however
comments still reference 'jiffies'.
Fixes: 8234f6734c (PM-runtime: Switch autosuspend over to using hrtimers)
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Driver rewritten, assign copyright notice and change module author
as original one remains silent and I want to be notified about bugs.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Sound capture and line bypass currently do not work as well as
some mixer controls. Fix that by building proper audio paths and
adjusting volume controls to match datasheet.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Drop "Common NI Values Table" and calculate LRCLK divider, then
add allowed rate constraints based on master clock frequency.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Implement set_bias_level to drive shutdown bit, so device is
put to sleep when unused.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Remove duplicated entry and add missing zero in rate constraints.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Allocating memory to store clk array together with driver
data simplifies error unwinding and allows deleting memory
allocation failure message as there is now only single point
of failure already covered by allocation failure report.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
[Markus Elfring: simplified error unwinding, error message removal]
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Acked-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Driver bails out with -EINVAL when no polling specififaion is requested.
Fix that by verifing polling interval only if polling_mode is different
from CM_POLL_DISABLE.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Power supply property is in fact enum, so reflect it in code.
Also use switch statement in show property function as is done
for storing property.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Driver generates lots of alignment trap exceptions on ARM.
Fix that by replacing typecasting of odd addresses with
byte shifting and remove uneccessary typecasting.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Cc: Bernie Thompson <bernie@plugable.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Platform data are now used only during probe time, so remove
them from gpio_charger structure and consolidate probing
function accordingly.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
[Replace of_property_read_string with dev_property_read_string]
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Setting GPIOF_ACTIVE_LOW flag based on platform data gpio_active_low
makes return value of gpiod_get_value_cansleep directly usable.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
As devm_ioremap_resource() checks for valid resource,
make use of it instead of testing ourselves. As a bonus
memory region is requested.
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Driver probe function has no use and can be deleted.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Codes is stereo only with playback and capture streams bind
to the same rate.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Tell user what are clock rate limits and reindent log messages.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Invalid value silently disables use of the prescaler.
Use -1 explicitely for that purpose and error out on
invalid value.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Reorder omap_dm_timer_set_source internals to get
source verification more straightforward.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
As dmtimer no longer exports functions, make those previously
exported static (this requires few functions to be moved around
as their prototypes were deleted).
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
In the case of device tree boot the device platform data is usually
NULL so hook the platform data obtained from the match.
As part of un-constify the platform_data pointer.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Keerthy <j-keerthy@ti.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Simplify error unwinding using devm_* allocators. This also
makes driver remove function empty, so remove it.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
pinctrl/devinfo.h is using forward declaration from pinctrl/consumer.h
for configurations with CONFIG_PINCTRL defined, however nothing declares
it in the opposite case. Fix this by adding a forward declaration.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
dev_err already provides messages with prefix, so drop 'ASoC'
prefix.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use dev_*() logging functions instead of plain printk and as
messages are now properly prefixed drop 'ASoC' prefix as well.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use dev_err() and dev_info() instead of pr_err() and pr_info().
USB device is used as argument to dev_*() functions for probe
and urb manipulation, FB device for framebuffer related info.
Also noisy device probe output was partly removed as idVendor,
idProduct, name and serial are already printed by usb core,
and partly turned into debug output.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Cc: Bernie Thompson <bernie@plugable.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Both dlfb_fix and fb_device_attrs are never written to, so
it is safe to make them const.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Cc: Bernie Thompson <bernie@plugable.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Variable 'dev' is usually used for 'struct device'. Therefore
rename driver private data to dlfb to avoid confusion once
driver will be using dev_*() logging functions.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Cc: Bernie Thompson <bernie@plugable.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
These warnings comes from times of driver development and do
not carry any usefull debugging information.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Cc: Bernie Thompson <bernie@plugable.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Move away from platform data configuration and use pure DT approach.
Use generic probe function to deal with OneNAND node and remove now useless
gpmc_probe_onenand_child function. Import sync mode timing calculation
function from mach-omap2/gpmc-onenand.c
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Reviewed-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Acked-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
INT pin (gpio_irq) is not really needed for DMA but only for notification
when a command that needs wait has completed. DMA memcpy can be still used
even without gpio_irq available, so enable it unconditionally.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Reviewed-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Acked-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Second commit in driver history (782b7a367d: "[MTD] [OneNAND] OMAP3:
add delay for GPIO") added quirk for waiting until GPIO line settle.
As DMA was disabled for OMAP2 boards, chances are this problem was
not OMAP3 specific and as it is just one register read, previous
test for SoC type is approximately as expensive as read itself.
Make delay unconditional, which allows removing SoC specific code
alltogether.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Reviewed-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Acked-by: Roger Quadros <rogerq@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Samsung E-die SLC NAND manufactured using 21nm process (K9F1G08U0E)
does not support partial page programming, so disable subpage writes
for it. Manufacturing process is stored in lowest two bits of 5th ID
byte.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Error out only if both 'bank-width' and 'gpmc,device-width' are missing.
As 'bank-width' is mostly used for NOR devices and all other devices must
use 'gpmc,device-width' update the error message accordingly.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Roger Quadros <rogerq@ti.com>
While usb_control_msg function expects timeout in miliseconds, a value
of HZ is used. Replace it with USB_CTRL_GET_TIMEOUT and also fix error
message which looks like:
udlfb: Read EDID byte 78 failed err ffffff92
as error is either negative errno or number of bytes transferred use %d
format specifier.
Returned EDID is in second byte, so return error when less than two bytes
are received.
Fixes: 18dffdf891 ("staging: udlfb: enhance EDID and mode handling support")
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Cc: Bernie Thompson <bernie@plugable.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Deprecated gpmc_update_nand_reg() is no longer used, remove.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Roger Quadros <rogerq@ti.com>
commit 67ce04bf27 ("mtd: nand: add OMAP2/OMAP3 NAND driver") assigned
pointer to omap_nand_info to the platform drvdata in probe function
just to be reasigned later to the pointer to mtd_info, which is
what remove function expects it to be. Remove useless assignment.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Acked-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The 0-day robot reports:
drivers/media/rc/gpio-ir-recv.c: In function 'gpio_ir_recv_irq':
>> drivers/media/rc/gpio-ir-recv.c:38:8: error: implicit declaration of function 'gpiod_get_value' [-Werror=implicit-function-declaration]
Fixes: eed008e605 ("[media] media: rc: gpio-ir-recv: use gpiolib API")
For some reason only partial patch was applied. Also include
gpio/consumer.h otherwise compile test fails.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Acked-by: Sean Young <sean@mess.org>
gpio_ir_recv_platform_data are not used anywhere in kernel tree,
so remove it.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Use of devm_request_irq simplifies error unwinding and as
free_irq was the last user of driver remove function,
remove it too.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Requesting any context irq is not actually great idea since threaded
interrupt handler is run at too unpredictable time which turns
timing information wrong. Fix it by requesting regular interrupt.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Using explicit struct device variable makes code a bit more readable.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
As user's guide "ADS1015EVM, ADS1115EVM, ADS1015EVM-PDK, ADS1115EVM-PDK
User Guide (Rev. B)" (http://www.ti.com/lit/ug/sbau157b/sbau157b.pdf)
states at page 16:
"Note that both the ADS1115 and ADS1015 have internal clocks with a ±10%
accuracy. If performing FFT tests, frequencies may appear to be incorrect
as a result of this tolerance range.", add those 10% to converion wait
time.
Cc: Daniel Baluta <daniel.baluta@gmail.com>
Cc: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Reviewed-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
In order to support LTC2942 which has temperature registers
at different offsets than LTC2943 use following register naming
scheme (prefixes):
- LTC294X_ common registers
- LTC2942_ chips specific registers
- LTC2943_ specific registers
LTC2944 is compatible with LTC2943 but uses different constants
to compute voltage and current, so replace num_regs misused
for device indentification with real device id to discriminate
between those two.
There are no functional changes.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Acked-by: Dragos Bogdan <dragos.bogdan@analog.com>
Tested-by: Dragos Bogdan <dragos.bogdan@analog.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Add OneNAND node for IGEP and leave it disabled by default. It is up
to bootloader to enable proper node. Timing just works, but values are
copied over from N900 as I was unable to find chip datasheet.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This code is no longer used and can be removed as we
are using device tree.
Removing this code also removes a dependency between
drivers/mtd and arch/arm/mach-omap2 making furhter driver
changes easier.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
[tony@atomide.com: removed from header too, updated comments]
Signed-off-by: Tony Lindgren <tony@atomide.com>
gpmc_probe_onenand_child returns success even on gpmc_onenand_init
failure. Fix that.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Acked-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
FDT harcoded partition table does not match that one in historical
TI's 2.6.37 kernel and non legacy kernels even use different ECC scheme,
yet noone complained, so remove it altogether.
Also, UBI volumes instead of partitions are used since u-boot-2016.09.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Don't complain on -EPROBE_DEFER when initializing controller,
the driver probe will be retried later.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Read urbs are submitted back only on success, causing read pipe
running out of urbs after few errors. No more characters can
be read from tty device then until it is reopened and no errors
are reported.
Fix that by always submitting urbs back and clearing stall on
-EPIPE.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Acked-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move urb killing code into separate function and use it
instead of copying that code pattern over.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Acked-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Ladislav Michl