Currently, whenever we idle a device _idle_sysc() is called and writes to the
devices SYSCONFIG register to set the idle mode. A lot devices are using the
smart-idle mode and so the write to the SYSCONFIG register is programming the
same value that is already stored in the register.
Writes to the devices SYSCONFIG register can be slow, for example, writing to
the DMTIMER SYSCONFIG register takes 3 interface clock cycles and 3 functional
clock cycles. If the DMTIMER is using the slow 32kHz functional clock this can
take ~100us.
Furthermore, during boot on an OMAP4430 panda board, I see that there are 100
calls to _idle_sysc(), however, only 3 out of the 100 calls actually write
the SYSCONFIG register with a new value.
Therefore, to avoid unnecessary writes to device SYSCONFIG registers when
idling the device, only write the value if the value has changed. It should be
safe to do this on idle as the context of the register will never be lost while
the device is active.
Verified that suspend, CORE off and retention states are working with this
change on OMAP3430 Beagle board.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
[paul@pwsan.com: updated to apply]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Commit 8c8a777 (ARM: OMAP2+: Add function to read GPMC settings from
device-tree) added a device-tree property "gpmc,device-nand" to indicate
is the GPMC child device is NAND. This commit should have updated the
GPMC NAND documentation (Documentation/devicetree/bindings/mtd/gpmc-nand.txt)
to list the property "gpmc,device-nand" as a required property and also
updated the example. However, this property is redundant and not needed
because the GPMC child device node for NAND is called "nand". Therefore,
remove this property.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Commit a2797be (gpio/omap: force restore if context loss is not
detectable) broke gpio support for OMAP when booting with device-tree
because a restore of the gpio context being performed without ever
initialising the gpio context. In other words, the context restored was
bad.
This problem could also occur in the non device-tree case, however, it
is much less likely because when booting without device-tree we can
detect context loss via a platform specific API and so context restore
is performed less often.
Nevertheless we should ensure that the gpio context is initialised
on the first pm-runtime resume for gpio banks that could lose their
state regardless of whether we are booting with device-tree or not.
The context loss count was being initialised on the first pm-runtime
suspend following a resume, by populating the get_count_loss_count()
function pointer after the first pm-runtime resume. To make the code
more readable and logical, initialise the context loss count on the
first pm-runtime resume if the context is not yet valid.
Reported-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Acked-by: Santosh Shilimkar<santosh.shilimkar@ti.com>
Reviewed-by: Kevin Hilman <khilman@linaro.org>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Commit ff5c9059 (ARM: dts: OMAP3+: Correct gpio #interrupts-cells
property) updated the number of interrupt cells required for configuring
gpios as interrupts for other devices (such as ethernet controllers).
This update allowed the interrupt type (edge, level, etc) to be
configured via device-tree (as described in the
Documentation/devicetree/bindings/gpio/gpio-omap.txt).
This broke ethernet support on the OMAP4 SDP board that defines a gpio
as the ethernet IRQ because the interrupt type (level, edge, etc) was
not getting configured correctly. This board use the ks8851 ethernet
chip which has an active low interrupt. Fix this by defining the gpio
interrupt as active-low in the device-tree binding.
Please note that the OMAP4-VAR-SOM also uses the same ethernet
controller and it is expected it will have the same problem. So the
same fix is also applied to this board.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The GPMC timing properties for device-tree have been updated
by adding a "-ns" or "-ps" suffix to indicate the units of
time the property represents. Therefore, update the timing
property names for TI GPMC NAND example.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
If the device-tree blob is present during boot, then register the SDMA
controller with the device-tree DMA driver so that we can use device-tree
to look-up DMA client information.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
When booting with device-tree the function pointer for detecting context
loss is not populated. Ideally, the pm_runtime framework should be
enhanced to allow a means for reporting context/state loss and we could
avoid populating such function pointers altogether. In the interim until
a generic non-device specific solution is in place, force a restore of
the gpio bank when enabling the gpio controller.
Adds a new device-tree property for the OMAP GPIO controller to indicate
if the GPIO controller is located in a power-domain that never loses
power and hence will always maintain its logic state.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The OMAP GPIO interrupt service routine is checking each bit in the
GPIO interrupt status register to see which bits are set. It is not
efficient to check every bit especially if only a few bits are set.
Therefore, instead of checking every bit use the __ffs() function,
which returns the location of the first set bit, to find all the set
bits.
This optimisation was suggested-by and developed in collaboration
with Felipe Balbi.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Currently the IRQ domain is not freed once allocated, in the case where
omap_gpio_probe() fails. Therefore, ensure we free the domain if the
probe does fail. Furthermore, the local variable "ret" is not needed
and so remove this.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add device-tree node for the 128MB NOR on the OMAP3430-SDP board.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
The GPMC timing properties for device-tree have been updated by adding
a "-ns" or "-ps" suffix to indicate the units of time the property
represents (as suggested by Rob Herring). Therefore, update the timing
property names for the OMAP3430 SDP NAND and ONENAND devices.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
Add the "ti,gpio-always-on" property to the appropriate GPIO banks to
indicate which banks are always powered and will never lose logic state.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
Currently the DMTIMER errata flags are not being populated when using
device-tree. Add static platform data to populate errata flags when
using device-tree.
Please note that DMTIMER erratum i767 is applicable to OMAP3-5 devices
as well as AM335x devices.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
Update the DMTIMER compatibility property to reflect the register level
compatibilty between devices and update the various OMAP/AM timer
bindings with the appropriate compatibility string.
By doing this we can add platform specific data applicable to specific
timer versions to the driver. For example, errata flags can be populated
for the timer versions that are impacted.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
Add a function so that OMAP dmtimers can be requested by device-tree
node. This allows for devices, such as the internal DSP, or drivers,
such as PWM, to reference a specific dmtimer node via the device-tree.
Given that there are several APIs available for requesting dmtimers
(by ID, by capability or by node) consolidate the code for all these
functions into a single helper function that can be used by these
request functions.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
When booting with device-tree the function pointer for detecting context
loss is not populated. Ideally, the pm_runtime framework should be
enhanced to allow a means for reporting context/state loss and we could
avoid populating such function pointers altogether. In the interim until
a generic non-device specific solution is in place, force a restore of
the dmtimer when enabling the timer.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
Adds basic device-tree support for OMAP3430 SDP board which has 256MB
of RAM, 128MB ONENAND flash, 256MB NAND flash and uses the TWL4030
power management IC.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
The OMAP3 gpio bindings are currently missing the reg and interrupt
properties and so add these properties.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
The OMAP gpio binding documention [1] states that the #interrupts-cells
property for gpio controllers should be 2. Currently, for OMAP3+ devices
the #interrupt-cells is set to 1. By setting this property to 2, it
allows clients to pass a 2nd parameter indicating the sensitivity (level
or edge) and polarity (high or low) of the interrupt. The OMAP gpio
controllers support these options and so update the #interrupt-cells
property for OMAP3+ devices to 2.
[1] Documentation/devicetree/bindings/gpio/gpio-omap.txt
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
Add the device-tree node for GPMC on OMAP2, OMAP4 and OMAP5 devices.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
Add SDMA controller binding for OMAP2+ devices and populate DMA client
information for SPI and MMC peripheral on OMAP3+ devices. Please note
that OMAP24xx devices do not have SPI and MMC bindings available yet and
so DMA client information is not populated.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
Add PMU nodes for OMAP2, OMAP3 and OMAP4460 devices.
Please note that the node for OMAP4460 has been placed in a separate
header file for OMAP4460, because the node is not compatible with
OMAP4430. The node for OMAP4430 is not included because PMU is not
currently supported on OMAP4430 due to the absence of a cross-trigger
interface driver.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
If device-tree is present, then do not create the PMU device from within
the OMAP specific PMU code. This is required to allow device-tree to
create the PMU device from the PMU device-tree node.
PMU is not currently supported for OMAP4430 (due to a dependency on
having a cross-trigger interface driver) and so ensure that this
indicated on boot with or without device-tree.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
When the GPMC driver is probed, we call gpmc_mem_init() to see which
chip-selects have already been configured and enabled by the boot-loader
and allocate space for them. If we fail to allocate space for one
chip-select, then we return failure from the probe and the GPMC driver
will not be available.
Rather than render the GPMC useless for all GPMC devices, if we fail to
allocate space for one chip-select print a warning and disable the
chip-select. This way other GPMC clients can still be used.
There is no downside to this approach, because all GPMC clients need to
request a chip-select before they can use the GPMC and on requesting a
chip-select, if memory has not already been reserved for the chip-select
then it will be.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Tested-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
With commit 21cc2bd (ARM: OMAP2+: Remove apollon board support) the
variable "boot_rom_space" is now not needed and the code surrounding
this variable can be cleaned up and simplified. Remove unnecessary
definitions and clean-up the comment as well.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Tested-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Each GPMC chip-select can be configured to map 16MB, 32MB, 64MB or 128MB
of address space. The physical base address where a chip-select starts
is also configurable and must be aligned on a boundary that is equal to
or greater than the size of the address space mapped bt the chip-select.
When enabling a GPMC chip-select, ensure that the base address is aligned
to the appropriate boundary.
Reported-by: Mark Jackson <mpfj-list@mimc.co.uk>
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Tested-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
When booting with device-tree, retrieve GPMC settings for ONENAND from
the device-tree blob. This will allow us to remove all static settings
stored in the gpmc-nand.c in the future once the migration to
device-tree is complete.
The user must now specify the ONENAND device width in the device-tree
binding so that the GPMC can be programmed correctly. Therefore, update
the device-tree binding documentation for ONENAND devices connected to
the GPMC to reflect this.
Please note that this does not include GPMC timings for ONENAND. The
timings are being calculated at runtime.
There is some legacy code that only enables read wait monitoring for
non-OMAP3 devices. There are no known OMAP3 device issues that prevent
this feature being enabled and so when booting with device-tree use the
wait-monitoring settings described in the device-tree blob.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Tested-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
When booting with device-tree, retrieve GPMC settings for NAND from
the device-tree blob. This will allow us to remove all static settings
stored in the gpmc-nand.c in the future once the migration to
device-tree is complete.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Tested-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
NOR flash is not currently supported when booting with device-tree
on OMAP2+ devices. Add support to detect and configure NOR devices
when booting with device-tree.
Add documentation for the TI GPMC NOR binding.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Tested-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Some of the GPMC timings parameters are currently missing from the GPMC
device-tree binding. Add these parameters to the binding documentation
as well as code to read them. Also add either "-ps" or "-ns" suffix to
the GPMC timing properties to indicate whether the timing is in
picoseconds or nanoseconds.
The existing code in gpmc_read_timings_dt() is checking the value of
of_property_read_u32() and only is successful storing the value read
in the gpmc_timings structure. Checking the return value in this case
is not necessary and we can simply read the value, if present, and
store directly in the gpmc_timings structure. Therefore, simplify the
code by removing these checks.
The comment in the gpmc_read_timings_dt() function, "only for OMAP3430"
is also incorrect as it is applicable to all OMAP3+ devices. So correct
this too.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Tested-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Adds a function to read the various GPMC chip-select settings from
device-tree and store them in the gpmc_settings structure.
Update the GPMC device-tree binding documentation to describe these
options.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Tested-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
With the addition of the gpmc_cs_program_settings(), we no longer need
or use gpmc_cs_configure() to configure some of the GPMC chip-select
options. So rename the function to gpmc_configure() and remove code that
modifies options in the CONFIG1 register.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Tested-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Convert the OMAP2+ TUSB code to use the gpmc_cs_program_settings()
function for configuring the various GPMC options instead of directly
programming the CONFIG1 register.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Tested-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Convert the OMAP2+ SMC91x code to use the gpmc_cs_program_settings()
function for configuring the various GPMC options instead of directly
programming the CONFIG1 register.
Move configuration of the GPMC settings outside retime function and
this does not need to be done if the timings are changed dynamically
at runtime.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Tested-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Convert the OMAP2+ NAND code to use the gpmc_cs_program_settings()
function for configuring the various GPMC options instead of directly
programming the CONFIG1 register.
This moves the configuration of some GPMC options outside the
nand_gpmc_retime() because these options should only need to be set once
regardless of whether the gpmc timing is changing dynamically at runtime.
The programming of where the wait-pin is also moved slightly, but this
will not have any impact to existing devices as no boards are currently
setting the dev_ready variable.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Tested-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Convert the OMAP2+ ONENAND code to use the gpmc_cs_program_settings()
function for configuring the various GPMC options instead of directly
programming the CONFIG1 register.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Tested-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
The GPMC has various different configuration options such as bus-width,
synchronous or asychronous mode selection, burst mode options etc.
Currently, there is no common function for configuring these options and
various devices set these options by either programming the GPMC CONFIG1
register directly or by calling gpmc_cs_configure() to set some of the
options.
Add a new function for configuring all of the GPMC options. Having a common
function for configuring this options will simplify code and ease the
migration to device-tree.
Also add a new capability flag to detect devices that support the
address-address-data multiplexing mode.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Tested-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
The GPMC has various different configuration options such as bus-width,
synchronous or asychronous mode selection, burst mode options etc.
Currently, there is no central structure for storing all these options
when configuring the GPMC for a given device. Some of the options are
stored in the GPMC timing structure and some are directly programmed
into the GPMC configuration register. Add a new structure to store
these options and convert code to use this structure. Adding this
structure will allow us to create a common function for configuring
these options.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Tested-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
The GPMC has wait-pin signals that can be assigned to a chip-select
to monitor the ready signal of an external device. Add a variable to
indicate the total number of wait-pins for a given device. This will
allow us to detect if the wait-pin being selected is valid or not.
When booting with device-tree read the number of wait-pins from the
device-tree blob. When device-tree is not used set the number of
wait-pins to 4 which is valid for OMAP2-5 devices. Newer devices
that have less wait-pins (such as AM335x) only support booting with
device-tree and so hard-coding the wait-pin number when not using
device-tree is fine.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Tested-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
The OMAP2+ code that configures the GPMC for ONENAND devices is copying
structures between functions unnecessarily. Avoid this by passing
pointers instead and simplify the code.
A pointer to structure "omap_onenand_platform_data" is passed to the
function omap2_onenand_calc_sync_timings(), but only the flags member
of the structure is used. Simplify the code by only passing the flags
member and not the entire structure.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Tested-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Commit 6bb27d7 (ARM: delete struct sys_timer) changed the function
created by the macro OMAP_SYS_32K_TIMER_INIT from static void to void.
For OMAP4+ devices this created the following sparse warning ...
arch/arm/mach-omap2/timer.c:585:1: warning: symbol
'omap4_sync32k_timer_init' was not declared. Should it be static?
The function omap4_sync32k_timer_init() is not referenced outside of the
file timer.c and so make this function static.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Currently, the timer ID is being passed to the function
omap_dm_timer_init_one(). Instead of passing the ID separately, store it
in the omap_dm_timer structure, that is also passed, and access the ID
from this structure.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
When booting with device-tree for OMAP3 and AM335x devices and a gptimer
is used as the clocksource (which is always the case for AM335x), a
gptimer located in a power domain that is not always-on is selected.
Ideally we should use a gptimer for clocksource that is located in a
power domain that is always on (such as the wake-up domain) so that time
can be maintained during a kernel suspend without keeping on additional
power domains unnecessarily.
In order to fix this so that we can select a gptimer located in a power
domain that is always-on, the following changes were made ...
1. Currently, only when selecting a gptimer to use for a clockevent
timer, do we pass a timer property that can be used to select a
specific gptimer. Change this so that we can pass a property when
selecting a gptimer to use for a clocksource timer too.
2. Currently, when selecting either a gptimer to use for a clockevent
timer or a clocksource timer and no timer property is passed, then
the first available timer is selected regardless of the properties
it has. Change this so that if no properties are passed, then a timer
that does not have additional features (such as always-on, dsp-irq,
pwm, and secure) is selected.
For OMAP3 and AM335x devices that use a gptimer for clocksource, change
the selection of the gptimer so that by default the gptimer located in
the always-on power domain is used for clocksource instead of
clockevents.
Please note that using a gptimer for both clocksource and clockevents
can have a system power impact during idle. The reason being is that
OMAP and AMxxx devices typically only have one gptimer in a power domain
that is always-on. Therefore when the kernel is idle both the clocksource
and clockevent timers will be active and this will keep additional power
domains on. During kernel suspend, only the clocksource timer is active
and therefore, it is better to use a gptimer in a power domain that is
always-on for clocksource.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
There is a lot of redundancy in the definitions for the various system
timers for OMAP2+ devices. For example, the omap3_am33xx_gptimer_timer_init()
function is the same as the omap3_gp_gptimer_timer_init() function and the
function omap4_sync32k_timer_init() can be re-used for OMAP5 devices.
Therefore, consolidate the definitions to simplify the code.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
In commit c59b537 (ARM: OMAP2+: Simplify dmtimer clock aliases), new
clock aliases for dmtimers were added to simplify the code. These clock
aliases can also be used when configuring the system timers and allow us
to remove the current definitions, simplifying the code.
Please note that for OMAP4/5 devices (unlike OMAP2/3 devices), there is
no clock alias for "timer_sys_ck" with NULL as the device name. Therefore
we still need to use the alias "sys_clkin_ck" for these devices.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Currently, when configuring the clock-events and clock-source timers
for OMAP2+ devices, we check whether the timer ID is 12 before
attempting to set the parent clock for the timer.
This test was added for OMAP3 general purpose devices (no security
features enabled) that a 12th timer available but unlike the other
timers only has a single functional clock source. Calling
clk_set_parent() for this 12th timer would always return an error
because there is only one choice for a parent clock. Therefore,
this hard-coded timer ID test was added.
To avoid this timer ID test, simply check to see if the timer's current
parent clock is the desired parent clock and only call clk_set_parent()
if this is not the case.
Also if clk_get() fails, then use PTR_ERR() to return the error code.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Currently on boot, when displaying the name of the gptimer used for
clockevents and clocksource timers, the timer ID is shown. However,
when booting with device-tree, the timer ID is not used to select a
gptimer but a timer property. Hence, it is possible that the timer
selected when booting with device-tree does not match the ID shown.
Therefore, instead display the HWMOD name of the gptimer and use
the HWMOD name as the name of clockevent and clocksource timer (if a
gptimer is used).
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Some versions of the u-boot bootloader do not lock the USB DPLL and
when the USB DPLL is not locked, then it is observed that the L3INIT
power domain does not transition to retention state during kernel
suspend on OMAP4 devices. Fix this by locking the USB DPLL at 960 MHz
on kernel boot.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
For OMAP devices, if a gpio is being used as an interrupt source but has
not been requested by calling gpio_request(), a call to request_irq()
may cause the kernel hang because the gpio bank may be disabled and
hence the register access will fail. To prevent such hangs, test for
this case and warn if this is detected.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Kevin Hilman <khilman@linaro.org>
Tested-by: Javier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Currently the OMAP GPIO driver uses a legacy mapping for the GPIO IRQ
domain. This is not necessary because we do not need to assign a
specific interrupt number to the GPIO IRQ domain. Therefore, convert
the OMAP GPIO driver to use a linear mapping instead.
Please note that this also allows to simplify the logic in the OMAP
gpio_irq_handler() routine, by using irq_find_mapping() to obtain the
virtual irq number from the GPIO bank and bank index.
Reported-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Kevin Hilman <khilman@linaro.org>
Tested-by: Javier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Commit 6797b4fe (ARM: OMAP2+: Prevent potential crash if GPMC probe fails)
added code to ensure that GPMC chip-selects could not be requested until the
device probe was successful. The chip-selects should have been
unreserved at the end of the probe function, but the code to unreserve
them appears to have ended up in the gpmc_calc_timings() function and
hence, this is causing problems requesting chip-selects. Fix this merge
error by unreserving the chip-selects at the end of the probe, but
before we call the gpmc child probe functions (for device-tree) which
request a chip-select.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Tested-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Tested-by: Philip Avinash <avinashphilip@ti.com>
Tested-by: Grazvydas Ignotas <notasas@gmail.com>
[tony@atomide.com: updated description to add breaking commit id]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Commit 8a6aaa3 (mfd: twl-core: Collect global variables behind one
private structure (global)) removed the variable "inuse" that is used
to determine if the device has been initialised and now use the
twl_priv structure instead. This is causing the kernel to panic on
OMAP3+ devices using the twl driver, because we try to access the
twl_priv->ready member before checking if twl_priv is initialised. Fix
this and move this test to the beginning of the twl_i2c_read/write
function because twl_get_last_module() also uses the twl_priv structure.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Commit 9725f44 (ARM: OMAP: Add DT support for timer driver) added
device-tree support for selecting a clockevent timer by property.
However, the code is currently ignoring the property passed and
selecting the first available timer found. Hence, for the OMAP3 beagle
board timer-12 is not being selected as expected. Fix this problem
by ensuring the timer property is passed to omap_get_timer_dt().
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Vaibhav Bedia <vaibhav.bedia@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
If the GPMC probe fails, devices that use the GPMC (such as ethernet
chips, flash memories, etc) can still allocate a GPMC chip-select and
register the device. On the OMAP2420 H4 board, this was causing the
kernel to crash after the gpmc probe failed and the board attempted
to start networking. Prevent this by marking all the chip-selects as
reserved by default and only make them available for devices to request
if the GPMC probe succeeds.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
During the migration to the common clock framework, calls to the
functions omap2xxx_clkt_vps_late_init() were not preserved for
OMAP2420 and OMAP2430. This causes the variables "sys_ck_rate" and
"curr_prcm_set" to be uninitialised on boot. On reboot, this causes the
following error message to be displayed because the appropriate MPU
clock frequency (derived from sys_ck_rate) cannot be found.
"Could not set MPU rate to 4294MHz"
Fix this by adding back calls to omap2xxx_clkt_vps_late_init() in the
OMAP2420 and OMAP2430 clock initialisation code.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
[paul@pwsan.com: dropped the duplicated call to
omap2xxx_clkt_vps_check_bootloader_rates() after consultation with Jon;
updated patch description]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
In the current implementation of the OF DMA helpers, read-copy-update (RCU)
linked lists are being used for storing and accessing the DMA controller data.
This part of implementation is based upon V2 of the DMA helpers by Nicolas [1].
During a recent review of RCU, it became apparent that the code is missing the
required rcu_read_lock()/unlock() calls as well as synchronisation calls before
freeing any memory protected by RCU.
Having looked into adding the appropriate RCU calls to protect the DMA data it
became apparent that with the current DMA helper implementation, using RCU is
not as attractive as it may have been before. The main reasons being that ...
1. We need to protect the DMA data around calls to the xlate function.
2. The of_dma_simple_xlate() function calls the DMA engine function
dma_request_channel() which employs a mutex and so could sleep.
3. The RCU read-side critical sections must not sleep and so we cannot hold
an RCU read lock around the xlate function.
Therefore, instead of using RCU, an alternative for this use-case is to employ
a simple spinlock inconjunction with a usage count variable to keep track of
how many current users of the DMA data structure there are. With this
implementation, the DMA data cannot be freed until all current users of the
DMA data are finished.
This patch is based upon the DMA helpers fix for potential deadlock [2].
[1] http://article.gmane.org/gmane.linux.ports.arm.omap/73622
[2] http://marc.info/?l=linux-arm-kernel&m=134859982520984&w=2
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
In the latest version of the OF dma handlers I added support (rather hastily)
to exhaustively search for an available dma slave channel, for the use-case
where we have alternative slave channels that can be used. In the current
implementation a deadlock scenario can occur causing the CPU to loop forever.
The scenario is as follows ...
1. There are alternative channels avaialble
2. The first channel that is found by calling of_dma_find_channel() is not
available and so the call to the xlate function returns NULL. In this case
we will call of_dma_find_channel() again but we will return the same channel
that we found the first time and hence, again the xlate will return NULL and
we will loop here forever.
Fix this potential deadlock by just using a single for-loop and not a for-loop
nested in a do-while loop. This change also replaces the function
of_dma_find_channel() with of_dma_match_channel() which performs a simple check
to see if a DMA channel matches the name specified.
I have tested this implementation on an OMAP4 panda board by adding a dummy
DMA specifier, that will cause the xlate function to return NULL, to the
beginning of a list of DMA specifiers for a DMA client.
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Benoit Cousson <b-cousson@ti.com>
Cc: Stephen Warren <swarren@nvidia.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Vinod Koul <vinod.koul@intel.com>
Cc: Dan Williams <djbw@fb.com>
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
This is based upon the work by Benoit Cousson [1] and Nicolas Ferre [2]
to add some basic helpers to retrieve a DMA controller device_node and the
DMA request/channel information.
Aim of DMA helpers
- The purpose of device-tree is to describe the capabilites of the hardware.
Thinking about DMA controllers purely from the context of the hardware to
begin with, we can describe a device in terms of a DMA controller as
follows ...
1. Number of DMA controllers
2. Number of channels (maybe physical or logical)
3. Mapping of DMA requests signals to DMA controller
4. Number of DMA interrupts
5. Mapping of DMA interrupts to channels
- With the above in mind the aim of the DT DMA helper functions is to extract
the above information from the DT and provide to the appropriate driver.
However, due to the vast number of DMA controllers and not all are using a
common driver (such as DMA Engine) it has been seen that this is not a
trivial task. In previous discussions on this topic the following concerns
have been raised ...
1. How does the binding support devices with multiple DMA controllers?
2. How to support both legacy DMA controllers not using DMA Engine as
well as those that support DMA Engine.
3. When using with DMA Engine how do we support the various
implementations where the opaque filter function parameter differs
between implementations?
4. How do we handle DMA channels that are identified with a string
versus a integer?
- Hence the design of the DMA helpers has to accomodate the above or align on
an agreement what can be or should be supported.
Design of DMA helpers
1. Registering DMA controllers
In the case of DMA controllers that are using DMA Engine, requesting a
channel is performed by calling the following function.
struct dma_chan *dma_request_channel(dma_cap_mask_t mask,
dma_filter_fn filter_fn,
void *filter_param);
The mask variable is used to match a type of the device controller in a list
of controllers. The filter_fn and filter_param are used to identify the
required dma channel and return a handle to the dma channel of type dma_chan.
From the examples I have seen, the mask and filter_fn are constant
for a given DMA controller and therefore, we can specify these as controller
specific data when registering the DMA controller with the device-tree DMA
helpers.
The filter_param variable is of an unknown type and is typically specific
to the DMA engine implementation for a given DMA controller. To allow some
flexibility in the type and formating of this filter_param we employ an
xlate to translate the device-tree binding information into the appropriate
format. The xlate function used for a DMA controller can also be specified
when registering the DMA controller with the device-tree DMA helpers.
Based upon the above, a function for registering the DMA controller with the
DMA helpers now looks like the below. The data variable is used to pass a
pointer to DMA controller specific data used by the xlate function.
int of_dma_controller_register(struct device_node *np,
struct dma_chan *(*of_dma_xlate)
(struct of_phandle_args *, struct of_dma *),
void *data)
For example, in the case where DMA engine is used, we define the following
structure (that stores the DMA engine capability mask and filter function)
and pass this to the data variable in the above function.
struct of_dma_filter_info {
dma_cap_mask_t dma_cap;
dma_filter_fn filter_fn;
};
2. Representing and requesting channel information
Please see the dma binding documentation included in this patch for a
description of how DMA controllers and client information should be
represented with device-tree. For more information on how this binding
came about please see [3]. In addition to this, feedback received from
the Linux kernel summit showed a consensus (among those who attended) to
use a name to identify DMA client information [4].
A DMA channel can be requested by calling the following function, where name
is a required parameter used for identifying a DMA channel. This function
has been designed to return a structure of type dma_chan to work with the
DMA engine driver. Note that if DMA engine is used then drivers should be
using the DMA engine API dma_request_slave_channel() (implemented in part 2
of this series, "dmaengine: add helper function to request a slave DMA
channel") which will in turn call the below function if device-tree is
present. The aim being to have a common DMA engine interface regardless of
whether device tree is being used.
struct dma_chan *of_dma_request_slave_channel(struct device_node *np,
char *name)
3. Supporting legacy devices not using DMA Engine
These devices present a problem, as there may not be a uniform way to easily
support them with regard to device tree. Ideally, these should be migrated
to DMA engine. However, if this is not possible, then they should still be
able to use this binding, the only constaint imposed by this implementation
is that when requesting a DMA channel via of_dma_request_slave_channel(), it
will return a type of dma_chan.
This implementation has been tested on OMAP4430 using the kernel v3.6-rc5. I
have validated that MMC is working on the PANDA board with this implementation.
My development branch for testing on OMAP can be found here [5].
v6: - minor corrections in DMA binding documentation
v5: - minor update to binding documentation
- added loop to exhaustively search for a slave channel in the case where
there could be alternative channels available
v4: - revert the removal of xlate function from v3
- update the proposed binding format and APIs based upon discussions [3]
v3: - avoid passing an xlate function and instead pass DMA engine parameters
- define number of dma channels and requests in dma-controller node
v2: - remove of_dma_to_resource API
- make property #dma-cells required (no fallback anymore)
- another check in of_dma_xlate_onenumbercell() function
[1] http://article.gmane.org/gmane.linux.drivers.devicetree/12022
[2] http://article.gmane.org/gmane.linux.ports.arm.omap/73622
[3] http://marc.info/?l=linux-omap&m=133582085008539&w=2
[4] http://pad.linaro.org/arm-mini-summit-2012
[5] https://github.com/jonhunter/linux/tree/dev-dt-dma
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Benoit Cousson <b-cousson@ti.com>
Cc: Stephen Warren <swarren@nvidia.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Vinod Koul <vinod.koul@intel.com>
Cc: Dan Williams <djbw@fb.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Reviewed-by: Stephen Warren <swarren@wwwdotorg.org>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
Currently slave DMA channels are requested by calling dma_request_channel()
and requires DMA clients to pass various filter parameters to obtain the
appropriate channel.
With device-tree being used by architectures such as arm and the addition of
device-tree helper functions to extract the relevant DMA client information
from device-tree, add a new function to request a slave DMA channel using
device-tree. This function is currently a simple wrapper that calls the
device-tree of_dma_request_slave_channel() function.
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Benoit Cousson <b-cousson@ti.com>
Cc: Stephen Warren <swarren@nvidia.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Vinod Koul <vinod.koul@intel.com>
Cc: Dan Williams <djbw@fb.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Reviewed-by: Stephen Warren <swarren@wwwdotorg.org>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
The ETM/ETB drivers for OMAP3, enable the emu_src_ck clock in order
to access the ETM/ETB hardware. The emu_src_ck should enable the EMU
clock domain so that the ETM/ETB hardware is accessible. However,
currently when enabling the emu_src_ck the EMU clock domain is not
being enabled and so the ETM/ETB drivers are failing. Add enable/disable
clock functions to enable the EMU clock domain when enabling the
emu_src_ck.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Commit 2ac29a1 (ARM: PMU: fix runtime PM enable) moved the call to
pm_runtime_enable() from the OMAP2+ PMU code into the ARM PERF core
code. However, header for pm_runtime which should have been removed
from the OMAP2+ PMU code was not. It is no longer necessary to include
this header in the OMAP2+ PMU code and so remove it.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Commit d043d87 (ARM: OMAP2+: clockdomain: bypass clockdomain handling
when disabling unused clks) skips the decrementing of a clock-domains
use count if the clocks use count is zero. However, for OMAP4 devices
this is causing the EMU clock-domain to be stuck ON as the use count is
not getting decremented correctly.
The scenario that leads to this problem is described below ...
omap_hwmod_setup_all
--> _setup
--> clkdm_hwmod_enable
--> EMU clock domain usecount = 1
--> _enable_clocks
--> clk_enable
--> trace_clk_div_div usecount = 1
--> clkdm_hwmod_enable
--> EMU clock domain usecount = 2
--> _idle
--> _disable_clocks
--> clk_disable
--> trace_clk_div_div usecount = 0
--> clkdm_hwmod_disable
--> skips decrement of EMU clock domain usecount
because trace_clk_div_div is 0!
--> EMU clock domain usecount = 2
--> clkdm_hwmod_disable
--> EMU clock domain usecount = 1
Hence, due to the order that a clocks use count is decremented and the
clock domain is disabled, it is possible that the clock domain can have
a non-zero use count when the actual clock has a use count of 0.
Therefore, we should only bypass the clock-domain handling when both the
clock-domain and clock in the clock-domain have a use count of 0 and
warn when the clock-domain has a zero use count and the clock has a
non-zero use count.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
[paul@pwsan.com: fixed checkpatch warning]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
With the latest mainline u-boot bootloader (v2012.10), timers (5-8) in
the ABE power domain are failing to turn-on. The timers never come out
of the disabled state when setting the module-mode field to enable.
The problem was exposed when u-boot was updated to NOT configure and
lock the ABE DPLL on start-up. If the ABE DPLL is configured and locked
by u-boot the problem does not occur. However, if the ABE DPLL is in the
idle low-power bypass state and we attempt to enable a timer in the ABE
power domain, it remains stuck in the disabled state. It appears to be a
problem the timer interface clock as this comes from the ABE DPLL.
If we place the ABE DPLL in the MN-bypass state and not the idle
low-power state, then this problem is not seen.
This problem only appears to occur on OMAP4460 and not OMAP4430.
Workaround this problem by locking the ABE DPLL for OMAP4460 in the
kernel on boot. By locking the ABE DPLL, when clocks from the ABE DPLL
are not being requested the DPLL will transition into a low-power stop
mode.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
On OMAP4 devices, the ABE DPLL has an internal 4X multiplier that can
be enabled or disabled in addition to the standard configurable
multiplier (M) for OMAP DPLLs. When configuring the ABE DPLL the 4X
multiplier is accounted for by checking to see whether it is enabled or
not. However, when calculating a new rate we only check to see if the
rate can be achieved with the current setting for the 4X multiplier.
Enhance the round_rate() function for such DPLLs to see if the rate
can be achieved with the 4X multiplier if it cannot be achieved without
the 4X multiplier.
This change is necessary, because when using the 32kHz clock as the
source clock for the ABE DPLL, the default DPLL frequency for the ABE
DPLL cannot be achieved without enabling the 4X multiplier.
When using the 32kHz clock as the source clock for the ABE DPLL and
attempting to lock the DPLL to 98.304MHz (default frequency), it was
found that the DPLL would fail to lock if the low-power mode for the DPLL
was not enabled. From reviewing boot-loader settings that configure the
ABE DPLL it was found that the low-power mode is enabled when using the
32kHz clock source, however, the documentation for OMAP does not state
that this is a requirement. Therefore, introduce a new function for
OMAP4 devices to see if low-power mode can be enabled when calculating a
new rate to ensure the DPLL will lock.
New variables for the last calculated 4X multiplier and low-power
setting have been added to the dpll data structure as well as variables
defining the bit mask for enabling these features via the DPLL's
control_reg. It is possible that we could eliminate these bit masks from
the dpll data structure as these bit masks are not unique to OMAP4, if
it is preferred.
The function omap3_noncore_program_dpll() has been updated to avoid
passing the calculated values for the multiplier (M) and divider (N) as
these are stored in the clk structure.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Currently all OMAP4 non-core DPLLs use the same function table for
configuring DPLLs. For these DPLLs, the function
omap4_dpll_regm4xen_recalc() is used to recalculate the DPLL rate and
the function omap4_dpll_regm4xen_round_rate() is used to calculate the
closest rate to that requested. However, these omap4_dpll_regm4xen_xxx()
functions are only applicable to the ABE DPLL and not the other non-core
DPLLs. Therefore, add a new function table for non-core DPLLs that do
not include the 4X-multiplier (M4X).
Please note that using these omap4_dpll_regm4x_xxx() function works for
the non-M4X DPLLs today because we only check to see if the 4X
multiplier is enabled when calculating the rate. However, it is planned
that the dpll functions will be enhanced to enable the 4X multiplier as
necessary (in order to achieve the requested rate) and so calling these
functions for non-M4X dplls will no longer work.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Commit "ARM: dts: OMAP4: Update timer addresses" updated the device-tree
names of the OMAP4 timers 5-7 because the default address for the timers
was changed from the L3 address to the MPU private address. When booting
with device-tree, this introduces a regression when attempting to set
the parent clock of timers 5-7 to the sys_clk_div_ck. Therefore, update
the clock aliases for timer 5-7 to reflect the updated device-tree name
for the timers.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
[paul@pwsan.com: updated to apply after the CCF conversion]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Commit 0d9250c (ARM: dts: omap4-panda: Add pinmux configuration for
HDMI) added a new device-tree source file for Rev A4 of the OMAP4430
Panda board but it did not add this version to the makefile. Hence,
add this file to the makefile.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The system memory node for the OMAP2420 H4 was incorrectly defined as
start address followed by end address, instead of start address and
size. No noticable side-effects were observed but fix this for
correctness.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The OMAP2420 H4 board was the only board using the
plat-omap/debug-devices.c code for configuring ethernet support. Now
that OMAP2420 H4 has been migrated to use the generic gpmc code for
configuring ethernet support, the debug-devices.c file is no longer
used and so remove it and its header file.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Ethernet is not currently working on the OMAP2420 H4 board. In commit
f604931 (ARM: OMAP: abstract debug card setup (smc, leds)) the function
h4_init_smc91x() that initialised the ethernet controller was renamed to
h4_init_debug() but was never called when initialising the board.
Adding a call to h4_init_debug() fixes ethernet support, however,
instead of using the legacy H4 code migrate the H4 to use the
gpmc_smc91x_init() function instead and remove the legacy H4 code.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
When compiling the kernel with configuration options ...
# CONFIG_ARCH_OMAP2 is not set
# CONFIG_ARCH_OMAP3 is not set
# CONFIG_ARCH_OMAP4 is not set
# CONFIG_SOC_OMAP5 is not set
CONFIG_SOC_AM33XX=y
... the following build warning is seen.
CC arch/arm/mach-omap2/timer.o
arch/arm/mach-omap2/timer.c:395:19: warning: ‘omap2_sync32k_clocksource_init’
defined but not used [-Wunused-function]
This issue was introduced by commit 6f80b3b (ARM: OMAP2+: timer: remove
CONFIG_OMAP_32K_TIMER) where the omap2_sync32k_clocksource_init() is no
longer referenced by the timer initialisation function for the AM335x
device as it has no 32k-sync timer.
Fix this by adding the "__maybe_unused" compiler directive to the
omap2_sync32k_clocksource_init() function to indicate that this function
may be used for certain configurations.
Cc: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
In commit fa6d79d (ARM: OMAP: Add initialisation for the real-time
counter), the function realtime_counter_init() was added. However, if
the kernel configuration option CONFIG_SOC_OMAP5 is not selected then
the following compiler warning is observed.
CC arch/arm/mach-omap2/timer.o
arch/arm/mach-omap2/timer.c:489:20: warning: ‘realtime_counter_init’
defined but not used [-Wunused-function]
Commit fa6d79d also introduced the kernel configuration option
CONFIG_SOC_HAS_REALTIME_COUNTER. If this option is not selected then the
a stub function for realtime_counter_init() is defined.
For non-OMAP5 devices, there is no realtime counter and so
realtime_counter_init() function and stub function are not used for
these devices. Therefore, fix this warning by only allowing the kernel
configuration option CONFIG_SOC_HAS_REALTIME_COUNTER to be enabled for
OMAP5 devices.
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reported-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Acked-by Santosh Shilimkar <santosh.shilimkar@ti.com>
Commit "ARM: OMAP2+: Add device-tree support for 32kHz counter"
added structure omap_counter_match to the OMAP2 timer code. When
CONFIG_OMAP_32K_TIMER is not defined this structure generates the
following as it is not used.
CC arch/arm/mach-omap2/timer.o
arch/arm/mach-omap2/timer.c:163:28: warning: 'omap_counter_match'
defined but not used [-Wunused-variable]
Move the definition of omap_counter_match to avoid this warning when
CONFIG_OMAP_32K_TIMER is not set.
Thanks to Kevin Hilman for tracking down and reporting this problem.
Reported-by: Kevin Hilam <khilman@deeprootsystems.com>
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Some source files are including dmtimer.h but not actually using any dmtimer
definitions or functions. Therefore, remove the inclusion dmtimer.h from these
source files.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Acked-by: Omar Ramirez Luna <omar.luna@linaro.org>
Remove unnecessary declaration of structure omap_dm_timer from dmtimer.h and
move the actual declaration of structure omap_dm_timer towards top of dmtimer.h
to avoid any compilation errors.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
The function omap_dm_timer_init_one() declares two local variables of
type int that are used to store the return value of functions called.
One such local variable is sufficient and so remove one of these local
variables.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
The OMAP2+ system timer code stores the physical address of the timer
but never uses it. Remove this and clean-up the code by removing the
local variable "size" and changing the names of the local variables
mem_rsrc and irq_rsrc to mem and irq, respectively.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
The omap_dm_timer_prepare function is a local function only used in the
dmtimer.c file. Therefore, make this a static function and remove its
declaration from the dmtimer.h file.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Only OMAP1 devices use the omap_dm_timer_reset() and so require the
omap_dm_timer_wait_for_reset() and __omap_dm_timer_reset() functions.
Therefore combine these into a single function called omap_dm_timer_reset()
and simplify the code.
The omap_dm_timer_reset() function is now the only place that is using the
omap_dm_timer structure member "sys_stat". Therefore, remove this member and
just use the register offset definition to simplify and clean-up the code. The
TISTAT register is only present on revision 1 timers and so check for this in
the omap_dm_timer_reset() function.
Please note that for OMAP1 devices, the TIOCP_CFG register does not have the
clock-activity field and so when we reset the timer for an OMAP1 device we
only need to configure the idle-mode field in the TIOCP_CFG register.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
The __omap_dm_timer_set_source() function is only used by the system timer
(clock-events and clock-source) code for OMAP2+ devices. Therefore, we can
remove this code from the dmtimer driver and move it to the system timer
code for OMAP2+ devices.
The current __omap_dm_timer_set_source() function calls clk_disable() before
calling clk_set_parent() and clk_enable() afterwards. We can avoid these calls
to clk_disable/enable by moving the calls to omap_hwmod_setup_one() and
omap_hwmod_enable() to after the call to clk_set_parent() in
omap_dm_timer_init_one().
The function omap_hwmod_setup_one() will enable the timers functional clock
and therefore increment the use-count of the functional clock to 1.
clk_set_parent() will fail if the use-count is not 0 when called. Hence, if
omap_hwmod_setup_one() is called before clk_set_parent(), we will need to call
clk_disable() before calling clk_set_parent() to decrement the use-count.
Hence, avoid these extra calls to disable and enable the functional clock by
moving the calls to omap_hwmod_setup_one() and omap_hwmod_enable() to after
clk_set_parent().
We can also remove the delay from the __omap_dm_timer_set_source() function
because enabling the clock will now be handled via the HWMOD framework by
calling omap_hwmod_setup_one(). Therefore, by moving the calls to
omap_hwmod_setup_one() and omap_hwmod_enable() to after the call to
clk_set_parent(), we can simply replace __omap_dm_timer_set_source() with
clk_set_parent().
It should be safe to move these hwmod calls to later in the
omap_dm_timer_init_one() because other calls to the hwmod layer that occur
before are just requesting resource information.
Testing includes boot testing on OMAP2420 H4, OMAP3430 SDP and OMAP4430 Blaze
with the following configurations:
1. CONFIG_OMAP_32K_TIMER=y
2. CONFIG_OMAP_32K_TIMER=y and boot parameter "clocksource=gp_timer"
3. CONFIG_OMAP_32K_TIMER not set
4. CONFIG_OMAP_32K_TIMER not set and boot parameter "clocksource=gp_timer"
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Whenever we call the function omap_dm_timer_set_source() to set the clock
source of a dmtimer we look-up the dmtimer functional clock source by
calling clk_get(). This is not necessary because on requesting a dmtimer
we look-up the functional clock source and store it in the omap_dm_timer
structure. So instead of looking up the clock again used the clock handle
that stored in the omap_dm_timer structure.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
The OMAP dmtimer driver does not currently have a function to disable the
timer interrupts. For some timer instances the timer interrupt enable
function can be used to disable the interrupts because the same interrupt
enable register is used to disable interrupts. However, some timer instances
have separate interrupt enable/disable registers and so this will not work.
Therefore, add a dedicated function to disable interrupts.
This change is required for OMAP4+ devices. For OMAP4, all timers apart from 1,
2 and 10 need this function and for OMAP5 all timers need this function.
Please note that the interrupt disable function has been written so that it
can be used by all OMAP devices.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
The OMAP DMTIMERs can generate an interrupt when the timer counter value
matches the value stored in the timer's match register. When using this
feature spurious interrupts were seen, because the compare logic is being
enabled before the match value is loaded and according to the documentation
the match value must be loaded before the compare logic is enable.
The reset value for the timer counter and match registers is 0 and hence,
by enabling the compare logic before the actual match value is loaded a
spurious interrupt can be generated as the reset values match.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Restoring the timer interrupt status is not possible because writing a 1 to any
bit in the register clears that bit if set and writing a 0 has no affect.
Furthermore, if an interrupt is pending when someone attempts to disable a
timer, the timer will fail to transition to the idle state and hence it's
context will not be lost. Users should take care to service all interrupts
before disabling the timer.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
The timer TISTAT register is a read-only register and therefore restoring the
context is not needed. Furthermore, the context of TISTAT is never saved
anywhere in the current code. The TISTAT register is read-only for all OMAP
devices from OMAP1 to OMAP4. OMAP5 timers no longer have this register.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
In commit e32f7ec2 (ARM: OMAP: Fix 32 kHz timer and modify GP timer to use GPT1)
a fix was added to prevent timer1 being reset in the function
omap_dm_timer_reset() because timer1 was being used as the system timer for
OMAP2 devices. Although timer1 is still used by most OMAP2+ devices as a system
timer, the function omap_dm_timer_reset() is now only being called for OMAP1
devices and OMAP1 does not use timer1 as a system timer. Therefore, remove the
check in omap_dm_timer_reset() so that timer1 is reset for OMAP1 devices.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Currently OMAP2+ devices are using the function __omap_dm_timer_reset() to
configure the clock-activity, idle, wakeup-enable and auto-idle fields in the
timer OCP_CFG register. The name of the function is mis-leading because this
function does not actually perform a reset of the timer.
For OMAP2+ devices, HWMOD is responsible for reseting and configuring the
timer OCP_CFG register. Therefore, do not use __omap_dm_timer_reset() for
OMAP2+ devices and rely on HWMOD. Furthermore, some timer instances do not
have the fields clock-activity, wakeup-enable and auto-idle and so this
function could configure the OCP_CFG register incorrectly.
Currently HWMOD is not configuring the clock-activity field in the OCP_CFG
register for timers that have this field. Commit 0f0d080 (ARM: OMAP: DMTimer:
Use posted mode) configures the clock-activity field to keep the f-clk enabled
so that the wake-up capability is enabled. Therefore, add the appropriate flags
to the timer HWMOD structures to configure this field in the same way.
For OMAP2/3 devices all dmtimers have the clock-activity field, where as for
OMAP4 devices, only dmtimer 1, 2 and 10 have the clock-activity field.
Verified on OMAP2420 H4, OMAP3430 Beagle and OMAP4430 Panda that HWMOD is
configuring the dmtimer OCP_CFG register as expected for clock-events timer.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
For OMAP2/3 devices, the HWMOD data does not define a software reset status
field for the DMTIMERs. Therefore, when HWMOD performs a soft-reset of the
DMTIMER we don't check and wait for the reset to complete. For OMAP2/3 devices,
the software reset status for a DMTIMER can be read from bit 0 of the DMTIMER
TISTAT register (referred to as the SYSS register in HWMOD). Add the
appropriate HWMOD definitions so that HWMOD will check the software reset
status when performing a software reset of the DMTIMER.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Currently, the OMAP3 HWMOD data defines two TIOCP_CFG register structures
(referred to as the SYSC register in the HWMOD data) where timers 1, 2 and 10
use one of the defintions and the other timers use the other definition. For
OMAP3 devices the structure of the DMTIMER TIOCP_CFG register is the same for
all 12 instances of the DMTIMER. Please note that this is a difference between
OMAP3 and OMAP4 and could be the source of the confusion.
For OMAP3 devices, the DMTIMER TIOCP_CFG register has the fields,
clock-activity, emufree, idlemode, enwakeup, softreset and autoidle for all
12 timers. Therefore, remove one of the SYSC register definitions for the
DMTIMERs and ensure the appropriate register fields are defined for all
DMTIMERs.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Currently the dmtimer posted mode is being enabled when the function
omap_dm_timer_enable_posted() is called. This function is only being called
for OMAP1 timers and OMAP2+ timers that are being used as system timers. Hence,
for OMAP2+ timers that are NOT being used as a system timer, posted mode is
not enabled but the "timer->posted" variable is still set (incorrectly) in
the omap_dm_timer_prepare() function.
This is a regression introduced by commit 3392cdd3 (ARM: OMAP: dmtimer:
switch-over to platform device driver) which was before the
omap_dm_timer_enable_posted() function was introduced. Although this is a
regression from the original code it only impacts performance and so is not
needed for stable.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Errata Titles:
i103: Delay needed to read some GP timer, WD timer and sync timer
registers after wakeup (OMAP3/4)
i767: Delay needed to read some GP timer registers after wakeup (OMAP5)
Description (i103/i767):
If a General Purpose Timer (GPTimer) is in posted mode
(TSICR [2].POSTED=1), due to internal resynchronizations, values read in
TCRR, TCAR1 and TCAR2 registers right after the timer interface clock
(L4) goes from stopped to active may not return the expected values. The
most common event leading to this situation occurs upon wake up from
idle.
GPTimer non-posted synchronization mode is not impacted by this
limitation.
Workarounds:
1). Disable posted mode
2). Use static dependency between timer clock domain and MPUSS clock
domain
3). Use no-idle mode when the timer is active
Workarounds #2 and #3 are not pratical from a power standpoint and so
workaround #1 has been implemented. Disabling posted mode adds some CPU
overhead for configuring and reading the timers as the CPU has to wait
for accesses to be re-synchronised within the timer. However, disabling
posted mode guarantees correct operation.
Please note that it is safe to use posted mode for timers if the counter
(TCRR) and capture (TCARx) registers will never be read. An example of
this is the clock-event system timer. This is used by the kernel to
schedule events however, the timers counter is never read and capture
registers are not used. Given that the kernel configures this timer
often yet never reads the counter register it is safe to enable posted
mode in this case. Hence, for the timer used for kernel clock-events,
posted mode is enabled by overriding the errata for devices that are
impacted by this defect.
For drivers using the timers that do not read the counter or capture
registers and wish to use posted mode, can override the errata and
enable posted mode by making the following function calls.
__omap_dm_timer_override_errata(timer, OMAP_TIMER_ERRATA_I103_I767);
__omap_dm_timer_enable_posted(timer);
Both dmtimers and watchdogs are impacted by this defect this patch only
implements the workaround for the dmtimer. Currently the watchdog driver
does not read the counter register and so no workaround is necessary.
Posted mode will be disabled for all OMAP2+ devices (including AM33xx)
using a GP timer as a clock-source timer to guarantee correct operation.
This is not necessary for OMAP24xx devices but the default clock-source
timer for OMAP24xx devices is the 32k-sync timer and not the GP timer
and so should not have any impact. This should be re-visited for future
devices if this errata is fixed.
Confirmed with Vaibhav Hiremath that this bug also impacts AM33xx
devices.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
For OMAP2+ devices, when using DMTIMERs for system timers (clock-events and
clock-source) the posted mode configuration of the timers is used. To allow
the compiler to optimise the functions for configuring and reading the system
timers, the posted flag variable is hard-coded with the value 1. To make it
clear that posted mode is being used add some definitions so that it is more
readable.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Commit 7be2958 (ARM: PMU: Add runtime PM Support) updated the ARM PMU code to
use runtime PM which was prototyped and validated on the OMAP devices. In this
commit, there is no call pm_runtime_enable() and for OMAP devices
pm_runtime_enable() is currently being called from the OMAP PMU code when the
PMU device is created. However, there are two problems with this:
1. For any other ARM device wishing to use runtime PM for PMU they will need
to call pm_runtime_enable() for runtime PM to work.
2. When booting with device-tree and using device-tree to create the PMU
device, pm_runtime_enable() needs to be called from within the ARM PERF
driver as we are no longer calling any device specific code to create the
device. Hence, PMU does not work on OMAP devices that use the runtime PM
callbacks when using device-tree to create the PMU device.
Therefore, call pm_runtime_enable() directly from the ARM PMU driver when
registering the device. For platforms that do not use runtime PM,
pm_runtime_enable() does nothing and for platforms that do use runtime PM but
may not require it specifically for PMU, this will just add a little overhead
when initialising and uninitialising the PMU device.
Tested with PERF on OMAP2420, OMAP3430 and OMAP4460.
Acked-by: Kevin Hilman <khilman@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
For OMAP devices, the 32kHz counter is the default clock-source for the kernel.
However, this is not the only possible clock-source the kernel can use for OMAP
devices.
When booting with device-tree, if the 32kHz counter is the desired clock-source
for the kernel, then parse the device-tree blob to ensure that the counter is
present and if so map memory for the counter using the device-tree of_iomap()
function so we are no longer reliant on the OMAP HWMOD framework to do this for
us.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
In order to add device-tree support to the timer driver the following changes
were made ...
1. Allocate system timers (used for clock-events and clock-source) based upon
timer properties rather than using an hard-coded timer instance ID. To allow
this a new helper function called omap_dmtimer_find_by_property() has been
added for finding a timer with the particular properties in the device-tree
blob. Please note that this is an internal helper function for system timers
only to find a timer in the device-tree blob. This cannot be used by device
drivers, another API has been added for that (see below). Timers that are
allocated for system timers are dynamically disabled at boot time by adding
a status property with the value "disabled" to the timer's device-tree node.
Please note that when allocating system timers we now pass a timer ID and
timer property. The timer ID is only be used for allocating a timer when
booting without device-tree. Once device-tree migration is complete, all
the timer ID references will be removed.
2. System timer resources (memory and interrupts) are directly obtained from
the device-tree timer node when booting with device-tree, so that system
timers are no longer reliant upon the OMAP HWMOD framework to provide these
resources.
3. If DT blob is present, then let device-tree create the timer devices
dynamically.
4. When device-tree is present the "id" field in the platform_device structure
(pdev->id) is initialised to -1 and hence cannot be used to identify a timer
instance. Due to this the following changes were made ...
a). The API omap_dm_timer_request_specific() is not supported when using
device-tree, because it uses the device ID to request a specific timer.
This function will return an error if called when device-tree is present.
Users of this API should use omap_dm_timer_request_by_cap() instead.
b). When removing the DMTIMER driver, the timer "id" was used to identify the
timer instance. The remove function has been modified to use the device
name instead of the "id".
5. When device-tree is present the platform_data structure will be NULL and so
check for this.
6. The OMAP timer device tree binding has the following optional parameters ...
a). ti,timer-alwon --> Timer is in an always-on power domain
b). ti,timer-dsp --> Timer can generate an interrupt to the on-chip DSP
c). ti,timer-pwm --> Timer can generate a PWM output
d). ti,timer-secure --> Timer is reserved on a secure OMAP device
Search for the above parameters and set the appropriate timer attribute
flags.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Jon Hunter