The motion detection block requires 3 fields to create the motion vector
data. This means that using the default method the first progressive
frame is only generated after 3rd field is consumed.
Hence by default for N input field we would generate N - 2 progressive
frames.
In order to generate N progressive frames from N fields we use the
line averaging mode of the de-interlacer for the first 2 fields and then
revert back to the preferred Edge Directed Interpolation method (using
the motion vector).
Thus creating 2 line averaged frames + N - 2 motion based frames for a
total of N frames.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Nikhil Devshatwar <nikhil.nd@ti.com>
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add a 'port' parameter in dpi_select_source. The param tells the port
number of the DPI instance that we want to configure. We use this number
to select the overlay manager for that DPI instance.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Register DPI outputs, and assign the port_num to them as specified by the
'reg' property in the DPI ports in DT.
To support multiple DPI instances, dpi_get_channel needs to take the DPI
instance's port number to get the corresponding channel. Make it take this
argument. We just pass 0 in the non-DT path, since we don't support multiple
instances in the non-DT case.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
In omapdss_of_find_source_for_first_ep, we retrieve a source endpoint's DT node,
and then see what omapdss output has the matching device_node pointer in
omap_dss_find_output_by_node.
For all DPI and SDI outputs, the device_node pointer is set as the parent's DSS
device_node pointer. If the source is one of these outputs, the above method
won't work.
To get the correct output for ports within DSS(and in other cases in the future,
where multiple ports might be under one device), we require additional
information which is exclusive to the output port.
We create a new field in omap_dss_device called 'port_num', this provides port
number of the output port corresponding to this device. When searching for the
source endpoint in DT, we extract the 'reg' property from the port corresponding
to the endpoint source. From the list of registered outputs, we pick out that
output which has both dev->of_node and port_num matching with the device_node
pointer and 'reg' of the source endpoint node from DT.
For encoder blocks(the ones which have both an input and output port), we need
to set the port_num as the 'reg' property for the output port as defined in the
DT bindings. We set port_num to 1 in the tfp410 and tpd12s015 encoder drivers.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The init/uninit port functions are used to set up the DPI and SDI outputs under
the dss platform device. A 'reg' property is used to determine the port number
of the output. This tells us whether the port is DPI or SDI for OMAP34xx DSS
revision. For other DSS revisions, we only have DPI outputs under the dss
platform device.
For multiple DPI output instances(introduced in DRA7xx DSS), we will use the
the port number to specify which DPI output instance is being inited.
The current functions work fine if there is only one DPI output instance in
DSS. For multiple DPI instances, it would get complicated to figure out whether
port number was used to specify whether the output is SDI, or another DPI
instance.
We create a list of port types supported for each DSS rev, with the index of the
port in the list specifying the port number of the output for that DSS revision.
This allows us to have a more generic way to init/uninit ports within DSS, and
also support multiple DPI ports.
We make the uninit_port functions iterative since we will have multiple DPI
ports to uninit in the future.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
DPI and SDI ports are backed by only one parent DSS device. We don't have a
corresponding platform_device for ports under DSS. In order to support multiple
instances of DPI, we need to pass the driver data pointer through the DPI port's
private data ('data' member in device_node struct).
dpi_init_output/dpi_uninit_output are untouched and only used for non-DT case,
these are called when the DPI platform device probed/removed. These funcs will
be removed when non-DT mode is removed.
dpi_init_output_port/dpi_uninit_output_port are created and used for the DT
path, called when DSS inits/uninits it's ports. These new functions retrieve
the dpi_data pointer from 'port->data', and not from the platform device's
data(pdev->dev) like in the non-DT path.
We add some code in dss_uninit_ports() to pass a pointer to the DPI port in
dpi_uninit_port().
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Allocate driver data(dpi_data) for each DPI instance. It's allocated in
omap_dpi_probe() when DT isn't used, and in dpi_init_port() when DT is used.
The dpi_data struct instance is no longer global. In the case of DPI ops, it's
retrieved from dpi_get_data_from_dssdev(). 'dssdev' passed by the connected
encoder/panel driver is a pointer to the 'output' member in dpi_data, and thus
can be used to get the DPI instance's driver data. In the case of probe/ini_port
functions, it's set as DPI/DSS device's private data embedded in the
platform_device struct.
Having dpi_data as private data of the platform device will not work for
multiple DPI instances in the DT case. This is because there is no corresponding
platform_device for DPI or SDI, they exist only as ports under the parent DSS
platform_device in the DT case. The DPI port's private data('data' member in
device_node struct) will later be used to store dpi_data.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
DPI related data is currently a static global struct parameter. It is accessed
directly by functions in the driver.
This method won't work if we want the driver to support multiple DPI instances.
Create struct dpi_data, and pass its pointer to functions which need to use it.
We still have a static instance defined for dpi_data, which is accessed by top
level DPI ops. This will be removed when the driver dynamically allocates
dpi_data for each DPI instance.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
This removes the sparse warnings on arm platforms:
warning: cast removes address space of expression
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: H Hartley Sweeten <hsweeten at visionengravers.com>
Cc: Alexander Shiyan <shc_work@mail.ru>
Cc: Russell King <linux@arm.linux.org.uk>
Rename the memory block resource "vpe_csc" to "csc" since it also exists within
the VIP IP block. This would make the name more generic, and both VPE and VIP DT
nodes in the future can use it.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Add selection ioctl ops. For VPE, cropping makes sense only for the input to
VPE(or V4L2_BUF_TYPE_VIDEO_OUTPUT/MPLANE buffers) and composing makes sense
only for the output of VPE(or V4L2_BUF_TYPE_VIDEO_CAPTURE/MPLANE buffers).
For the CAPTURE type, V4L2_SEL_TGT_COMPOSE results in VPE writing the output
in a rectangle within the capture buffer. For the OUTPUT type, V4L2_SEL_TGT_CROP
results in selecting a rectangle region within the source buffer.
Setting the crop/compose rectangles should successfully result in
re-configuration of registers which are affected when either source or
destination dimensions change, set_srcdst_params() is called for this purpose.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Some parameters of the VPE descriptors were understood incorrectly. They are now
fixed. The fixes are explained as follows:
- When adding an inbound data descriptor to the VPDMA descriptor list, we intend
to use c_rect as the cropped region fetched by VPDMA. Therefore, c_rect->width
shouldn't be used to calculate the line stride, the original image width
should be used for that. We add a 'width' argument which gives the buffer
width in memory.
- frame_width and frame_height describe the complete width and height of the
client to which the channel is connected. If there are multiple channels
fetching data and providing to the same client, the above 2 arguments should
be the width and height of the region covered by all the channels. In the case
where there is only one channel providing pixel data to the client
(like in VPE), frame_width and frame_height should be the cropped width and
cropped height respectively. The calculation of these params is done in the
vpe driver now.
- start_h and start_v is also used in the case of multiple channels to describe
where each channel should start filling pixel data. We don't use this in VPE,
and pass 0s to the vpdma_add_in_dtd() helper.
- Some minor changes are made to the vpdma_add_out_dtd() helper. The c_rect
param is used for specifying the 'composition' target, and 'width' is added
to calculate the line stride.
Signed-off-by: Archit Taneja <archit@ti.com>
Acked-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
For OMAP and DRA7x, we generally allocate video and graphics buffers through
omapdrm since the corresponding omap-gem driver provides DMM-Tiler backed
contiguous buffers. omapdrm is a dma-buf exporter. These buffers are used by
other drivers in the video pipeline.
Add VB2_DMABUF flag to the io_modes of the vb2 output and capture queues. This
allows the driver to import dma shared buffers.
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
vpe fops(vpe_open in particular) should be called only when VPDMA firmware
is loaded. File operations on the video device are possible the moment it is
registered.
Currently, we register the video device for VPE at driver probe, after calling
a vpdma helper to initialize VPDMA and load firmware. This function is
non-blocking(it calls request_firmware_nowait()), and doesn't ensure that the
firmware is actually loaded when it returns.
We remove the device registration from vpe probe, and move it to a callback
provided by the vpe driver to the vpdma library, through vpdma_create().
The ready field in vpdma_data is no longer needed since we always have firmware
loaded before the device is registered.
A minor problem with this approach is that if the video_register_device
fails(which doesn't really happen), the vpe platform device would be registered.
however, there won't be any v4l2 device corresponding to it.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Add hwmod data for dss core, dispc dsi1, dsi2, rfbi and hdmi. It's more
or less similar to omap4 hwmod data.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Add a features struct to differentiate between the HDMI PLLs on OMAP4
and OMAP5. The OMAP5 PLL is more sensitive when it comes to locking. We
need to ensure that the DCO freq isn't too low for lower pixel clocks.
Modify the PLL computation slightly to ensure the HDMI PLL locks for lower
frequencies. This will be later replaced by a more complex computation
which makes sure all the PLL constraints are met.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
OMAP5 HDMI PHY has some differences compared to OMAP4 HDMI PHY. This
patch creates a features struct which help the driver configure the PHY
based on what SoC it is.
Some of the features aren't currenlty used, but will come in use later.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The HDMI core IP on OMAP5 has a wider address range for registers. The offsets
for the later registers can't fit into the u16 type currently used for hdmi
register read and write functions. Use u32 for offsets instead.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The support for simpler port/endpoint binding was removed in the merged version
of omapdss DT. But dss_init_ports still tries to get to an endpoint even if no
port exists. Remove this as this doesn't work.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The vblank_cb callback and the page_flip ioctl can occur together in different
CPU contexts. vblank_cb uses takes tje drm device's event_lock spinlock when
sending the vblank event and updating omap_crtc->event and omap_crtc->od_fb.
Use the same spinlock in page_flip, to make sure the above omap_crtc parameters
are configured sequentially.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
omap_crtc->old_fb is used to check whether the previous page flip has completed
or not. However, it's never initialized to anything, so it's always NULL. This
results in the check to always succeed, and the page_flip to proceed.
Initialize old_fb to the fb that we intend to flip to through page_flip, and
therefore prevent a future page flip to proceed if the last one didn't
complete.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The channel_names list didn't have a string populated for LCD3 manager, this
results in a crash when the display's output is connected to LCD3. Add an entry
for LCD3.
Reported-by: Somnath Mukherjee <somnath@ti.com>
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
A waiter of the type OMAP_GEM_READ should wait for a buffer to be completely
written, and only then proceed with reading it. A similar logic applies for
waiters with OMAP_GEM_WRITE flag.
Currently the function is_waiting() waits on the read_complete/read_target
counts in the sync object.
This should be the other way round, as a reader should wait for users who are
'writing' to this buffer, and vice versa.
Make readers of the buffer(OMAP_GEM_READ) wait on the write counters, and
writers to the buffer(OMAP_GEM_WRITE) wait on the read counters in is_waiting()
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The dequed CAPTURE_MPLANE type buffers don't contain the flags that the
originally queued OUTPUT_MPLANE type buffers have. This breaks compliance.
Copy the source v4l2_buffer flags to the destination v4l2_buffer flags before
they are dequed.
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The vpe driver wasn't setting the correct field parameter for dequed CAPTURE
type buffers for the case where the captured output is progressive.
Set the field to V4L2_FIELD_NONE for the completed destination buffers when
the captured output is progressive.
For OUTPUT type buffers, a queued buffer's field is forced to V4L2_FIELD_NONE
if the pixel format(configured through s_fmt for the buffer type
V4L2_BUF_TYPE_VIDEO_OUTPUT_MPLANE specifies) the field type isn't interlaced.
If the pixel format specified was V4L2_FIELD_ALTERNATE, and the queued buffer's
field isn't V4L2_FIELD_TOP or V4L2_FIELD_BOTTOM, the vb2 buf_prepare op returns
an error.
This ensures compliance, and that the dequeued output and captured buffers
contain the field type that the driver used internally.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Zero out the reserved formats in v4l2_pix_format_mplane and
v4l2_plane_pix_format members of the returned v4l2_format pointer when passed
through TRY_FMT ioctl.
This ensures that the user doesn't interpret the non-zero fields as some data
passed by the driver, and ensures compliance.
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The vpe output and capture queues are initially configured to default values in
vpe_open(). A G_FMT before any S_FMTs will result in these values being
populated.
The colorspace and bytesperline parameter of this initial configuration are
incorrect. This breaks compliance when as we get 'TRY_FMT(G_FMT) != G_FMT'.
Fix the initial queue configuration such that it wouldn't need to be fixed by
try_fmt.
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The bus_info parameter in v4l2_capabilities expects a 'platform_' prefix. This
wasn't done in the driver and hence was breaking compliance. Update the bus_info
parameter accordingly.
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
querycap currently returns V4L2_CAP_VIDEO_M2M as a capability, this should be
V4L2_CAP_VIDEO_M2M_MPLANE instead, as the driver supports multiplanar formats.
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The minimum width and height for VPE input/output was kept as 128 pixels. VPE
doesn't have a constraint on the image height, it requires the image width to
be at least 16 bytes.
Change the minimum supported dimensions to 32x32. This allows us to de-interlace
qcif content. A smaller image size than 32x32 didn't make much sense, so stopped
at this.
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The video_device struct is currently embedded in the driver data struct vpe_dev.
A vpe_dev instance is allocated by the driver, and the memory for the vfd is a
part of this struct.
The v4l2 core, however, manages the removal of the vfd region, through the
video_device's .release() op, which currently is the helper
video_device_release. This causes memory corruption, and leads to issues when
we try to re-insert the vpe module.
Use the video_device_release_empty helper function instead.
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
VPE has a ctrl parameter which decides how many mem to mem transactions the
active job from the job queue can perform.
The driver's job_ready() made sure that the number of ready source buffers are
sufficient for the job to execute successfully. But it didn't make sure if
there are sufficient ready destination buffers in the capture queue for the
VPE output.
If the time taken by VPE to process a single frame is really slow, then it's
possible that we don't need to imply such a restriction on the dst queue, but
really fast transactions(small resolution, no de-interlacing) may cause us to
hit the condition where we don't have any free buffers for the VPE to write on.
Add the extra check in job_ready() to make sure we have the sufficient amount
of destination buffers.
Acked-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Add Dynamic Memory Manager (DMM) bindings for OMAP4 and OMAP5 and DRA7x devices.
DMM only requires address and irq information.
Add documentation for the DMM bindings.
Originally worked on by Andy Gross <andygro@gmail.com>
Cc: Andy Gross <andygro@gmail.com>
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
DISPC pipeline DMAs preload some bytes of pixel data in the vertical blanking
region before the start of each frame. The preload ensures the pipeline doesn't
underflow when the active region of the display starts.
DISPC_GFX/VIDp_PRELOAD registers allow us to program how many bytes of data
should be preloaded for each pipeline. Calculating a precise preload value
would be a complex function of the pixel clock of the connected display, the
vertical blanking duration and the interconnect traffic at that instance. If
the register is left untouched, a default value is preloaded.
We observe underflows for OMAP4+ SoCs for certain bandwidth intensive use cases
with many other initiators active, and in situations where memory access isn't
very efficient(like accessing Tiler mapped buffers and EMIF configured in
non-interleaved more). The cause of the underflow is because the default preload
value isn't sufficient for the DMA to reach a steady state. We configure the
PRELOAD register such that the pipelines preload data up to the high threshold
of the FIFO.
Preloading lot of data for older SoCs can have a negative impact. Due to slower
interconnects, it's possible that the DISPC DMA cannot preload up to the high
threshold within the vertical blanking region of the panel. We leave the PRELOAD
registers to their reset values since we haven't faced underflows with these
SoCs because of low value of PRELOAD.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The hdmi4 driver currently rejects any timing which is not from the CEA or VESA
standards. This leads hdmi rejecting any non-standard mode. A non standard
timing may not have a valid code corresponding to it. In such cases, the HDMI
spec suggests to set the code to 0.
Modify the driver to check if the timings fall within the range of the DISPC
TV overlay manager, and remove the check for an invalid code. Add a debug print
specifying the mode and code in hdmi_display_set_timing.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Enable use of DT for DMM/Tiler.
Originally worked on by Andy Gross <andygro@gmail.com>
Cc: Andy Gross <andygro@gmail.com>
Cc: DRI Development <dri-devel@lists.freedesktop.org>
Signed-off-by: Archit Taneja <archit@ti.com>
[tomi.valkeinen@ti.com: use of_match_ptr()]
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The current dev_unload order uninits the irqs too early.
In the current sequence, it's possible that a crtc queues work(apply_worker)
to display a buffer, which registers to omap_crtc_apply_irq to notfiy the
completion of the configuration we applied.
Calling drm_vblank_cleanup and omap_drm_irq_uninstall here causes the crtc's
apply handler to never get called, which results in an incorrect state of the
apply_irq.registered parameter.
This condition occurs where there is no mode set via omapdrm, and dev_lastclose
tries to set a default fb mode via drm_fb_helper_restore_fbdev_mode. The apply
work scheduled by restore_fbdev_mode is very close in time to the disabling of
the irq handler, and hence leads to a race condition. We move the irq cleanup
at the end of the unload sequence to prevent this.
Also, the call to flush_workqueue is removed since it's called internally by
destroy_workqueue.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Currently, an encoder is disabled only when an apply work is queued for the
corresponding crtc. This works fine for the paths where userspace explicitly
disables crtc, this results in disabling the omapdss device in the crtc's
pre_apply function.
However, when the omapdrm module is removed, there is no work queued to ensure
that the encoder is disabled. This can result in an enabled omapdss device when
removing omapdrm. omapdss is left in an inconsistent state, and that prevents us
from using that omapdss device being used again.
Disable enabled encoders in omap_encoder_destroy, we could consider a better
place for doing this later.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
At omapdrm probe, we install manager ops and connect omapdss devices. This
needs to be undone when omapdrm module is removed so that omapdss is in a
clean state. This ensures that we can re-insert omapdrm module, or some other
module which uses omapdss(like omapfb/omap_vout).
Currently, omapdrm's remove neither uninstalls manager ops, or disconnects
omapdss devices. We make sure that this is done in pdev_remove.
omapdrm establishes connections for omap_dss_device devices when probed. It
should also be responsible to disconnect the devices. Keeping the devices
connected can prevent the panel driver modules from unloading, it also causes
issues when we try to remove or re-insert omapdrm module.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
With the omapdss device model changes. omapdrm is required to call dssdriver's
connect() op to register a panel. This is currently done in omap_modeset_init()
A call to connect() can fail if the omapdss panels or the encoders(HDMI/DPI)
they connect to have some resource(like regulators, I2C adapter) missing. If
this happens, the correct approach is to defer omapdrm's probe.
omapdrm currently ignores those panels which return a non zero value when
connected. This could result in omapdrm ignoring all panels on an omap board.
The right approach would be for omapdrm to request for probe deferral when a
panel's connect op returns -EPROBE_DEFER.
In order to do this, we need to call connect() much earlier during omapdrm's
probe to prevent too many things are already done by then. We now connect the
panels during pdev_probe(), before anything else is initialized, so that we
don't need to undo too many things if a defer was requested.
Now when we enter omap_modeset_init(), we have a set of panels that have been
connected. We now proceed with registering only those panels that are already
connected.
A special case has to be considered when no panels are available to connect when
omapdrm probes. In this case too, we defer probe and expect that a panel will be
available to connect the next time.
Checking whether the panel has a driver or whether it has get_timing/read_edid
ops in omap_modeset_init() are redundant with the new display model. These can
be removed since a dssdev device will always have a driver associated with it,
and all dssdev drivers have a get_timings op.
This will mainly fix cases when omapdrm is built-in the kernel, since that's
generally where resources like regulators or I2C are unavailable because of
probe order dependencies.
In particular this fixes boot with omapdrm built-in on an omap4 panda ES board.
The regulators used by HDMI(provided by I2C based TWL regulators) aren't
initialized because I2C isn't initialized, I2C isn't initialized as it's pins
are not configured because pinctrl is yet to probe.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The struct vpdma_data_format holds the color format depth and the data_type
value needed to be programmed in the data descriptors. However, it doesn't
tell what type of color format is it, i.e, whether it is RGB, YUV or Misc.
This information is needed when by vpdma library when forming descriptors. We
modify the depth parameter for the chroma portion of the NV12 format. For this,
we check if the data_type value is C420. This isn't sufficient as there are
many YUV and RGB vpdma formats which have the same data_type value. Hence, we
need to hold the type of the color format for the above case, and possibly more
cases in the future.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Use the csc library functions to configure the CSC block in VPE.
Some changes are required in try_fmt to handle the pix->colorspace parameter
more correctly. Previously, we copied the source queue colorspace to the
destination queue colorspace as we didn't support RGB formats. Now, we configure
pix->colorspace based on the color format set(and the height of the image if
it's a YUV format).
Add basic RGB color formats to the list of supported vpe formats.
If the destination format is RGB colorspace, we also need to use the RGB output
port instead of the Luma and Chroma output ports. This requires configuring the
output data descriptors differently.
Also, make the default colorspace V4L2_COLORSPACE_SMPTE170M as that resembles
the Standard Definition colorspace more closely.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The CSC block can be used for color space conversion between YUV and RGB
formats.
It is configurable via a programmable set of coefficients. Add functionality to
choose the appropriate CSC coefficients and program them in the CSC registers.
We take the source and destination colorspace formats as the arguments, and
choose the coefficient table accordingly.
YUV to RGB coefficients are provided for standard and high definition
colorspaces. The coefficients can also be limited or full range. For now, only
full range coefficients are chosen. We would need some sort of control ioctl for
the user to specify the range needed. Not sure if there is a generic control
ioctl for this already?
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
VPE and VIP IPs in DAR7x contain a color space converter(CSC) sub block. Create
a library which will perform CSC related configurations and hold CSC register
definitions. The functions provided by this library will be called by the vpe
and vip drivers using a csc_data handle.
The vpe_dev holds the csc_data handle. The handle represents an instance of the
CSC hardware, and the vpe driver uses it to access the CSC register offsets or
helper functions to configure these registers.
The CSC register offsets are now relative to the CSC block itself, so we need
to use the macro GET_OFFSET_TOP to get the CSC register offset relative to the
VPE IP in the vpe driver.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Add the required SC register configurations which lets us perform linear scaling
for the supported range of horizontal and vertical scaling ratios.
The horizontal scaler performs polyphase scaling using it's 8 tap 32 phase
filter, decimation is performed when downscaling passes beyond 2x or 4x.
The vertical scaler performs polyphase scaling using it's 5 tap 32 phase filter,
it switches to a simpler form of scaling using the running average filter when
the downscale ratio is more than 4x.
Many of the SC features like peaking, trimming and non-linear scaling aren't
implemented for now. Only the minimal register fields required for basic scaling
operation are configured.
The function to configure SC registers takes the sc_data handle, the source and
destination widths and heights, and the scaler address data block offsets for
the current context so that they can be configured.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Make the driver allocate dma buffers to store horizontal and scaler coeffs.
Use the scaler library api to choose and copy scaler coefficients to a
the above buffers based on the scaling ratio. Since the SC block comes after
the de-interlacer, make sure that the source height is doubled if de-interlacer
was used.
These buffers now need to be used by VPDMA to load the coefficients into the
SRAM within SC.
In device_run, add configuration descriptors which have payloads pointing to
the scaler coefficients in memory. Use the members in sc_data handle to prevent
addition of these descriptors if there isn't a need to re-load coefficients into
SC. This comes helps unnecessary re-loading of the coefficients when we switch
back and forth between vpe contexts.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The SC block in VPE/VIP contains a SRAM within it. This internal memory
requires to be loaded with appropriate scaler coefficients from a contiguous
block of memory through VPDMA.
The horizontal and vertical scaler each require 2 sets of scaler coefficients
for luma and chroma scaling. The horizontal polyphase scaler requires
coefficients for a 32 phase and 8 tap filter. Similarly, the vertical scaler
requires coefficients for a 5 tap filter.
The choice of the scaler coefficients depends on the scaling ratio. Add
coefficient tables for different scaling ratios in sc_coeffs.h. In the case of
horizontal downscaling, we need to consider the change in ratio caused by
decimation performed by the horizontal scaler.
In order to load the scaler coefficients via VPDMA, a configuration descriptor
is used in block mode. The payload for the descriptor is the scaler coefficients
copied to memory. Coefficients for each phase have to be placed in memory in a
particular order understood by the scaler hardware.
The choice of the scaler coefficients, and the loading of the coefficients from
our tables to a contiguous buffer is managed by the functions
sc_set_hs_coefficients and sc_set_vs_coefficients.
The sc_data handle is now added with some parameters to describe the state of
the coefficients loaded in the SC block. 'loaded_coeff_h' and 'loaded_coeff_v'
hold the address of the last dma buffer which was used by VPDMA to copy
coefficients. This information can be used by a vpe mem-to-mem context to decide
whether it should load coefficients or not. 'hs_index' and 'vs_index' provide
some optimization by preventing loading of coefficients if the scaling ratio
didn't change between 2 contexts. 'load_coeff_h' and 'load_coeff_v' tell the
vpe/vip driver whether we need to load the coefficients through VPDMA or not.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
VPE and VIP IPs in DAR7x contain a scaler(SC) sub block. Create a library which
will perform scaler block related configurations and hold SC register
definitions. The functions provided by this library will be called by the vpe
and vip drivers using a sc_data handle.
The vpe_dev holds the sc_data handle. The handle represents an instance of the
SC hardware, and the vpe driver uses it to access the scaler register offsets
or helper functions to configure these registers.
We move the SC register definitions to sc.h so that they aren't specific to
VPE anymore. The register offsets are now relative to the sub-block, and not the
VPE IP as a whole. In order for VPDMA to configure registers, it requires it's
offset from the top level VPE module. A macro called GET_OFFSET_TOP is added to
return the offset of the register relative to the VPE IP.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
When VPDMA fetches or writes to an image buffer, the line stride must be a
multiple of 16 bytes. If it isn't, VPDMA HW will write/fetch until the next
16 byte boundry. This causes VPE to work incorrectly for source or destination
widths which don't satisfy the above alignment requirement.
In order to prevent this, we now make sure that when we set pix format for the
input and output buffers, the VPE source and destination image line strides are
16 byte aligned. Also, the motion vector buffers for the de-interlacer are
allocated in such a way that it ensures the same alignment.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The data_type value to be programmed in the data descriptors to fetch/write a
UYVY buffer was not mentioned correctly in the older DRA7x documentation. This
caused VPE to fail with UYVY color formats.
Update the data_type value to fix functionality when UYVY format is used.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Add support for the de-interlacer block in VPE. For de-interlacer to
work, we need to enable 2 more sets of VPE input ports which fetch data
from the 'last' and 'last to last' fields of the interlaced video. Apart
from that, we need to enable the Motion vector output and input ports,
and also allocate DMA buffers for them.
We need to make sure that two most recent fields in the source queue are
available and in the 'READY' state. Once a mem2mem context gets access
to the VPE HW(in device_run), it extracts the addresses of the 3
buffers, and provides it to the data descriptors for the 3 sets of input
ports((LUMA1, CHROMA1), (LUMA2, CHROMA2), and (LUMA3, CHROMA3))
respectively for the 3 consecutive fields. The motion vector and output
port descriptors are configured and the list is submitted to VPDMA.
Once the transaction is done, the v4l2 buffer corresponding to the
oldest field(the 3rd one) is changed to the state 'DONE', and the
buffers corresponding to 1st and 2nd fields become the 2nd and 3rd field
for the next de-interlace operation. This way, for each deinterlace
operation, we have the 3 most recent fields. After each transaction, we
also swap the motion vector buffers, the new input motion vector buffer
contains the resultant motion information of all the previous frames,
and the new output motion vector buffer will be used to hold the updated
motion vector to capture the motion changes in the next field. The
motion vector buffers are allocated using the DMA allocation API.
The de-interlacer is removed from bypass mode, it requires some extra
default configurations which are now added. The chrominance upsampler
coefficients are added for interlaced frames. Some VPDMA parameters like
frame start event and line mode are configured for the 2 extra sets of
input ports.
Signed-off-by: Archit Taneja <archit@ti.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
VPE is a block which consists of a single memory to memory path which
can perform chrominance up/down sampling, de-interlacing, scaling, and
color space conversion of raster or tiled YUV420 coplanar, YUV422
coplanar or YUV422 interleaved video formats.
We create a mem2mem driver based primarily on the mem2mem-testdev
example. The de-interlacer, scaler and color space converter are all
bypassed for now to keep the driver simple. Chroma up/down sampler
blocks are implemented, so conversion beteen different YUV formats is
possible.
Each mem2mem context allocates a buffer for VPE MMR values which it will
use when it gets access to the VPE HW via the mem2mem queue, it also
allocates a VPDMA descriptor list to which configuration and data
descriptors are added.
Based on the information received via v4l2 ioctls for the source and
destination queues, the driver configures the values for the MMRs, and
stores them in the buffer. There are also some VPDMA parameters like
frame start and line mode which needs to be configured, these are
configured by direct register writes via the VPDMA helper functions.
The driver's device_run() mem2mem op will add each descriptor based on
how the source and destination queues are set up for the given ctx, once
the list is prepared, it's submitted to VPDMA, these descriptors when
parsed by VPDMA will upload MMR registers, start DMA of video buffers on
the various input and output clients/ports.
When the list is parsed completely(and the DMAs on all the output ports
done), an interrupt is generated which we use to notify that the source
and destination buffers are done. The rest of the driver is quite
similar to other mem2mem drivers, we use the multiplane v4l2 ioctls as
the HW support coplanar formats.
Signed-off-by: Archit Taneja <archit@ti.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Create functions which the VPE driver can use to create a VPDMA
descriptor and add it to a VPDMA descriptor list. These functions take a
pointer to an existing list, and append the configuration/data/control
descriptor header to the list.
In the case of configuration descriptors, the creation of a payload
block may be required(the payloads can hold VPE MMR values, or scaler
coefficients). The allocation of the payload buffer and it's content is
left to the VPE driver. However, the VPDMA library provides helper
macros to create payload in the correct format.
Add debug functions to dump the descriptors in a way such that it's easy
to see the values of different fields in the descriptors.
Signed-off-by: Archit Taneja <archit@ti.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The primary function of VPDMA is to move data between external memory
and internal processing modules(in our case, VPE) that source or sink
data. VPDMA is capable of buffering this data and then delivering the
data as demanded to the modules as programmed. The modules that source
or sink data are referred to as clients or ports. A channel is setup
inside the VPDMA to connect a specific memory buffer to a specific
client. The VPDMA centralizes the DMA control functions and buffering
required to allow all the clients to minimize the effect of long latency
times.
Add the following to the VPDMA helper:
- A data struct which describe VPDMA channels. For now, these channels
are the ones used only by VPE, the list of channels will increase when
VIP(Video Input Port) also uses the VPDMA library. This channel
information will be used to populate fields required by data
descriptors.
- Data structs which describe the different data types supported by
VPDMA. This data type information will be used to populate fields
required by data descriptors and used by the VPE driver to map a V4L2
format to the corresponding VPDMA data type.
- Provide VPDMA register offset definitions, functions to read, write
and modify VPDMA registers.
- Functions to create and submit a VPDMA list. A list is a group of
descriptors that makes up a set of DMA transfers that need to be
completed. Each descriptor will either perform a DMA transaction to
fetch input buffers and write to output buffers(data descriptors), or
configure the MMRs of sub blocks of VPE(configuration descriptors), or
provide control information to VPDMA (control descriptors).
- Functions to allocate, map and unmap buffers needed for the descriptor
list, payloads containing MMR values and scaler coefficients. These use
the DMA mapping APIs to ensure exclusive access to VPDMA.
- Functions to enable VPDMA interrupts. VPDMA can trigger an interrupt
on the VPE interrupt line when a descriptor list is parsed completely
and the DMA transactions are completed. This requires masking the events
in VPDMA registers and configuring some top level VPE interrupt
registers.
- Enable some VPDMA specific parameters: frame start event(when to start
DMA for a client) and line mode(whether each line fetched should be
mirrored or not).
- Function to load firmware required by VPDMA. VPDMA requires a firmware
for it's internal list manager. We add the required request_firmware
apis to fetch this firmware from user space.
- Function to dump VPDMA registers.
- A function to initialize and create a VPDMA instance, this will be
called by the VPE driver with it's platform device pointer, this
function will take care of loading VPDMA firmware and returning a
vpdma_data instance back to the VPE driver. The VIP driver will also
call the same init function to initialize it's own VPDMA instance.
Signed-off-by: Archit Taneja <archit@ti.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The OMAP4 HDMI encoder driver(hdmi4.c) contains timings tables, and helper
functions which can be used as is by the OMAP5/DRA7x encoder driver. Move these
to hdmi_common.c so that it's not replicated in the future.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The hdmi4 driver has edid macros that aren't used at all. Remove them.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Replace the ti_hdmi_4xxx* notation for OMAP4 HDMI driver with hdmi4. Rename
the hdmi.c encoder driver to hdmi4.c. Rename ti_hdmi.h to hdmi.h
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Add flags for the interrupts present in HDMI wrapper block, these will be used
to configure HDMI_IRQENABLE_SET/CLEAR and HDMI_IRQSTATUS registers.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Keep only OMAP4 HDMI core block related structs and enums in ti_hdmi_4xxx_ip.h,
move the rest to ti_hdmi.h. This holds all library specific data which will be
shared between OMAP4 and OMAP5/DRA7x HDMI encoder drivers.
Move the duplicate register read/write/wait_for_bit_change functions in the hdmi
library files to ti_hdmi.h
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The struct hdmi_ip_data contains information related to HDMI wrapper, PLL, PHY
and core sub-blocks. Now that each of these sub blocks has it's own struct,
hdmi_ip_data serves no purpose. The mutex lock in the struct was also never
used.
Remove this struct to make things cleaner.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
After removing wrapper, pll and phy funcs from ti_hdmi_4xxx_ip.c, we are left
with OMAP4 HDMI core functions. Use these directly in hdmi.c rather than using
hdmi_ip_ops. Rename the core functions with a 'hdmi4' suffix.
We used to have hdmi_ip_ops so that one could support HDMI within a TI SoC which
had a non-DSS display subsytem. This however never got put into use, and hence
these ops aren't useful any more.
The DT/hwmod information for hdmi doesn't split the address space according to
the required sub blocks. Keep the address offset and size information in the
driver for now. This will be removed when the driver gets the information
correctly from DT/hwmod.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
HDMI PHY is a block common to DSS in OMAP4, OMAP5 and DRA7x. Move the
existing functions from ti_hdmi_4xxx_ip.c to a separate file. These funcs are
called directly from the hdmi driver rather than hdmi_ip_ops function pointer
calls.
Add the PHY library function declarations to ti_hdmi.h. These will be shared
amongst the omap4/5 hdmi platform drivers. Remove the PHY function pointer ops
from the ti_hdmi_ip_ops struct.
The DT/hwmod information for hdmi doesn't split the address space according to
the required sub blocks. Keep the address offset and size information in the
driver for now. This will be removed when the driver gets the information
correctly from DT/hwmod.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
HDMI PLL is a block common to DSS in OMAP4, OMAP5 and DRA7x. Move the
existing PLL functions from ti_hdmi_4xxx_ip.c and hdmi.c to a separate file.
These funcs are called directly from the hdmi driver rather than hdmi_ip_ops
function pointer calls.
Add the PLL library function declarations to ti_hdmi.h. These will be shared
amongst the omap4/5 hdmi platform drivers. Remove the PLL function pointer ops
from the ti_hdmi_ip_ops struct. These will be shared amongst the omap4/5 hdmi
platform drivers and other libraries.
The DT/hwmod information for hdmi doesn't split the address space according to
the required sub blocks. Keep the address offset and size information in the
driver for now. This will be removed when the driver gets the information
correctly from DT/hwmod.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
HDMI wrapper is a block common to DSS in OMAP4, OMAP5 and DRA7x. Move the
existing functions from ti_hdmi_4xxx_ip.c to a separate file. These funcs are
called directly from the hdmi driver rather than hdmi_ip_ops funtion pointer
calls.
Add new wrapper funcs which can be used by other hdmi libraries like core, pll
and phy. Move some of the enums, structs and funcs related to the wrapper from
ti_hdmi_4xxx_ip.h to ti_hdmi.h. These will be shared amongst the omap4/5 hdmi
platform drivers and other libraries.
The old hdmi_wp_init() is removed since it didn't do anything. Timing parameters
like interlace, hsync_level and vsync_level weren't copied correctly before.
Those are copied correctly now.
The DT/hwmod information for hdmi doesn't split the address space according to
the required sub blocks. Keep the address offset and size information in the
driver for now. This will be removed when the driver gets the information
correctly from DT/hwmod.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Move omap_vout device creation inside the omap_display_init so that we can
correctly create the device based on the presence of omapdss within the
platform.
For example, on a kernel image supporting multiple platforms, omap_init_vout
will create a omapdrm platform device on a AM33xx platform even though it
doesn't have a DSS block.
Signed-off-by: Archit Taneja <archit@ti.com>
Acked-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Move omapfb and omapvrfb device creation inside the omap_display_init so that
we can correctly create the device based on the presence of omapdss within the
platform.
For example, on a kernel image supporting multiple platforms, omap_init_vrfb and
omap_init_fb will create omapvrfb and omapfb platform devices respectively on a
AM33xx platform even though it doesn't have a VRFB or DSS block.
Signed-off-by: Archit Taneja <archit@ti.com>
Acked-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Move omapdrm device creation inside the omap_display_init so that we can
correctly create the device based on the presence of omapdss within the
platform.
For example, on a kernel image supporting multiple platforms, omap_init_drm
will create a omapdrm platform device on a AM33xx platform even though it
doesn't have a DSS block.
Originally worked on by Andy Gross.
Cc: Andy Gross <andygro@gmail.com>
Signed-off-by: Archit Taneja <archit@ti.com>
Acked-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
DMM exists on omap4+ platforms, these platforms are always expected to boot with
DT. Remove the current method of searching the dmm hwmod and building an
omap_device for dmm.
For OMAP4, the address and irq data for DMM hwmod(along with other blocks) were
removed, so the current method fails in the dmm driver's probe anyway.
The addition of DMM nodes in DT will ensure that a DMM device is built
correctly.
Cc: Andy Gross <andygro@gmail.com>
Signed-off-by: Archit Taneja <archit@ti.com>
Acked-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
drm_framebuffer_lookup() does a kref_get() for the framebuffer if it finds one
corresponding to the fb id passed to it. Use drm_framebuffer_reference() instead
for clarity since it's the function used in other places to take a reference.
Signed-off-by: Archit Taneja <archit@ti.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The omapdrm driver currently takes a config/module arg to figure out the number
of crtcs it needs to create. We could create as many crtcs as there are overlay
managers in the DSS hardware, but we don't do that because each crtc eats up
one DSS overlay, and that reduces the number of planes we can attach to a single
crtc.
Since the number of crtcs may be lesser than the number of hardware overlay
managers, we need to figure out which overlay managers to use for our crtcs. The
current approach is to use pipe2chan(), which returns a higher numbered manager
for the crtc.
The problem with this approach is that it assumes that the overlay managers we
choose will connect to the encoders the platform's panels are going to use,
this isn't true, an overlay manager connects only to a few outputs/encoders, and
choosing any overlay manager for our crtc might lead to a situation where the
encoder cannot connect to any of the crtcs we have chosen. For example, an
omap5-panda board has just one hdmi output. If num_crtc is set to 1, with the
current approach, pipe2chan will pick up the LCD2 overlay manager, which cannot
connect to the hdmi encoder at all. The only manager that could have connected
to hdmi was the TV overlay manager.
Therefore, there is a need to choose our overlay managers keeping in mind the
panels we have on that platform. The new approach iterates through all the
available panels, creates encoders and connectors for them, and then tries to
get a suitable overlay manager to create a crtc which can connect to the
encoders.
We use the dispc_channel field in omap_dss_output to retrieve the desired
overlay manager's channel number, we then check whether the manager had already
been assigned to a crtc or not. If it was already assigned to a crtc, we assume
that out of all the encoders which intend use this crtc, only one will run at a
time. If the overlay manager wan't assigned to a crtc till then, we create a
new crtc and link it with the overlay manager.
This approach just looks for the best dispc_channel for each encoder. On DSS HW,
some encoders can connect to multiple overlay managers. Since we don't try
looking for alternate overlay managers, there is a greater possibility that 2
or more encoders end up asking for the same crtc, causing only one encoder to
run at a time.
Also, this approach isn't the most optimal one, it can do either good or bad
depending on the sequence in which the panels/outputs are parsed. The optimal
way would be some sort of back tracking approach, where we improve the set of
managers we use as we iterate through the list of panels/encoders. That's
something left for later.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
When userspace calls SET_PLANE ioctl, drm core takes a reference of the fb and
passes control to the update_plane op defined by the drm driver.
In omapdrm, we have a worker thread which queues framebuffers objects received
from update_plane and displays them at the appropriate time.
It is possible that the framebuffer is destoryed by userspace between the time
of calling the ioctl and apply-worker being scheduled. If this happens, the
apply-worker holds a pointer to a framebuffer which is already destroyed.
Take an extra refernece/unreference of the fb in omap_plane_update() to prevent
this from happening. A reference is taken of the fb passed to update_plane(),
the previous framebuffer (held by plane->fb) is unreferenced. This will prevent
drm from destroying the framebuffer till the time it's unreferenced by the
apply-worker.
This is in addition to the exisitng reference/unreference in update_pin(),
which is taken for the scanout of the plane's current framebuffer, and an
unreference the previous framebuffer.
Signed-off-by: Archit Taneja <archit@ti.com>
Reviewed-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The omapdrm driver requires omapdss panel drivers to expose ops like detect,
set_timings and check_timings. These can be NULL for fixed panel DPI, DBI, DSI
and SDI drivers. At some places, there are no checks to see if the panel driver
has these ops or not, and that leads to a crash.
The following things are done to make fixed panels work:
- The omap_connector's detect function is modified such that it considers panel
types which are generally fixed panels as always connected(provided the panel
driver doesn't have a detect op). Hence, the connector corresponding to these
panels is always in a 'connected' state.
- If a panel driver doesn't have a check_timings op, assume that it supports the
mode passed to omap_connector_mode_valid(the 'mode_valid' drm helper function)
- The function omap_encoder_update shouldn't really do anything for fixed
resolution panels, make sure that it calls set_timings only if the panel
driver has one.
Signed-off-by: Archit Taneja <archit@ti.com>
Reviewed-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
modeset_init iterates through all the registered omapdss devices and has some
initial checks to see if the panel has a driver and the required driver ops for
it to be usable by omapdrm.
The function bails out from modeset_init if a panel doesn't meet the
requirements, and stops the registration of the future panels and encoders which
come after it, that isn't the correct thing to do, we should go through the rest
of the panels. Replace the 'return's with 'continue's.
Signed-off-by: Archit Taneja <archit@ti.com>
Reviewed-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Use devm_clk_get() instead of clk_get() for dss, and for outputs hdmi
and venc. This reduces code and simplifies error handling.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
DISPC on OMAP5 has a more optimised mechanism of asserting Mstandby to achieve
more power savings when DISPC is configured in Smart Standby mode. This
mechanism leads to underflows when multiple DISPC pipes are enabled.
There is a register field which can let us revert to the older mechanism of
asserting Mstandby. Configure this field to prevent underflows.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
When using a DISPC video pipeline to a fetch a NV12 buffer in a 2D container, we
need to set set a doublestride bit in the video pipe's ATTRIBUTES register. This
is needed because the stride for the UV plane(using a 16 bit Tiler container) is
double the stride for the Y plane(using a 8 bit Tiler container) for the 0 or
180 degree views. The ROW_INC register is meant for the Y plane, and the HW will
calculate the row increment needed for the UV plane by using double the stride
value based on whether this bit is set or not.
Set the bit when we are using a 2D Tiler buffer and when rotation is 0 or 180
degrees. The stride value is the same for 90 and 270 degree Tiler views, hence
the bit shouldn't be set.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Increase the DSS_FCLK and DSI_FCLK max supported frequencies, these come because
some frequencies were increased from OMAP5 ES1 to OMAP5 ES2. We support only
OMAP5 ES2 in the kernel, so replace the ES1 values with ES2 values. Increase the
DSI PLL Fint range, this was previously just copied from the OMAP4 param range
struct.
Fix the maximum DSS_FCLK on OMAP2, it's 133 Mhz according to the TRM.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Each version of OMAP has a limitation on the maximum pixel clock frequency
supported by an overlay manager. This limit isn't checked by omapdss. Add
dispc feats for lcd and tv managers and check whether the target timings can
be supported or not.
The pixel clock limitations are actually more complex. They depend on which OPP
OMAP is in, and they also depend on which encoder is the manager connected to.
The OPP dependence is ignored as DSS forces the PM framework to be on OPP100
when DSS is enabled, and the encoder dependencies are ignored by DISPC for now.
These limits should come from the encoder driver.
The OMAP2 TRM doesn't mention the maximum pixel clock limit. This value is left
as half of DSS_FCLK, as OMAP2 requires the PCD to be atleast 2.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
gpio reset info is passed to the tfp410 panel driver via the panel's platform
data struct 'tfp410_platform_data'. The tfp driver doesn't use the reset_gpio
field in the omap4_panda_dvi_device struct. Remove this field.
Signed-off-by: Archit Taneja <archit@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
The omap_dss_device's platform_enable/disable callbacks don't do anything for
any of the boards. The platform calls from the VENC driver will also be removed
in the future. Remove these calls from the board which have a VENC device.
Signed-off-by: Archit Taneja <archit@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
The dss-common file currently requests gpios required by the picodlp DPI
panel on the 4430sdp/blaze board. It also requests DISPLAY_SEL_GPIO and
DLP_POWER_ON_GPIO gpios which are board specific gpios to switch between lcd2
panel and picodlp, and setting intermediate power supplies for picodlp
respectively. These gpios are toggled through platform_enable/disable functions
called by the picodlp driver.
Remove the gpio requests for the gpios which are already requested by the panel
driver, and remove the platform callback functions and set the platform specific
gpios in such a way that lcd2 panel is selected for the LCD2 overlay manager and
the power supplies for picodlp are disabled.
Note: We need to revisit this so that we can enable and switch to picodlp if
that's the only panel driver available for the LCD2 overlay manager.
Signed-off-by: Archit Taneja <archit@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
The omap3pandora board file currently passes the reset gpio number to the
tpo-td043mtea1 panel driver via the reset_gpio field in omap_dss_device.
Platform related information should be passed via the panel driver's platform
data struct.
Add the reset gpio information to panel_tpo_td043_data so that it's passed to
the panel driver.
Signed-off-by: Archit Taneja <archit@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
The zoom board file currently requests gpios required by the nec-nl8048hl11-01
dpi panel, and provides dummy platform_enable/disable callbacks.
gpio request and configuration have been moved to the nec-nl8048hl11-01 panel
driver itself and shouldn't be done in the board files.
Remove the gpio requests and the platform callbacks from the board file. Add the
gpio information to panel_nec_nl8048_data so that it's passed to the panel
driver.
Signed-off-by: Archit Taneja <archit@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
The rx-51 board file currently requests gpios required by the acx565akm panel,
and provides platform_enable/disable callbacks to configure them.
These tasks have been moved to the acx565akm panel driver itself and shouldn't
be done in the board files.
Remove the gpio requests and the platform callbacks from the board file. Pass
the panel_acx565akm_data instance 'lcd_data' to omap_dss_device instead of
passing the gpio number in omap_dss_device's reset_gpio.
Add the gpio information to panel_acx565akm_data so that it's passed to the
panel driver.
Signed-off-by: Archit Taneja <archit@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
The omap3430sdp board file currently requests gpios required by the sharp_ls dpi
panel, and provides platform_enable/disable callbacks to configure them.
These tasks have been moved to the sharp_ls panel driver itself and shouldn't
be done in the board files.
Remove the gpio requests and the platform callbacks from the board file.
Add the gpio information to panel_sharp_ls037v7dw01_data so that it's
passed to the panel driver.
Out of sharp panel's configurable pins, all apart from resb_gpio are managed by
a CPLD on the display and set to a default value. Only the configurable pin is
passed to platform data.
The backlight GPIO doesn't go directly to the sharp panel, it is used to set up
a voltage supply which goes to the LED+ pin of the panel, hence it isn't passed
to panel as platform data, and configured in the board file itself. The
backlight used to previously toggle through the platform_enable/disable
callbacks, but now it is always on. This needs to be revisited.
Signed-off-by: Archit Taneja <archit@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
The omap3evm board file currently requests gpios required by the sharp_ls dpi
panel, and provides platform_enable/disable callbacks to configure them.
These tasks have been moved to the sharp_ls panel driver itself and shouldn't
be done in the board files.
Remove the gpio requests and the platform callbacks from the board file.
Add the gpio information to panel_sharp_ls037v7dw01_data so that it's passed
to the panel driver.
Note: The GPIOs OMAP3EVM_LCD_PANEL_ENVDD and OMAP3EVM_LCD_PANEL_BKLIGHT_GPIO
aren't directly connected to the sharp panel, hence they aren't passed to the
panel driver as platform data. These are set to a default value such that LCD
is enabled and backlight is on. These used to previously toggle through the
platform_enable/disable callbacks, but now these are always on. This needs to
be revisited.
Signed-off-by: Archit Taneja <archit@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
The overo board file currently requests gpios required by the lb035q02 panel,
and provides platform_enable/disable callbacks to configure them.
These tasks have been moved to the lb035q02 dpi panel driver itself and should
be removed from the board files.
The lb035q02 panel driver uses generic dpi panel's platform data struct
internally. Remove the gpio requests and the platform callbacks from the board
file. Add the gpio information to the generic dpi panel platform data struct so
that it's passed to the panel driver.
Signed-off-by: Archit Taneja <archit@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
The ldp board file currently requests gpios required to configure the NEC DPI
panel, and provides platform_enable/disable callbacks to configure them.
These tasks have been moved to the generic dpi panel driver itself and shouldn't
be done in the board files.
Remove the gpio requests and the platform callbacks from the board file.
Configure the gpio information in generic dpi panel's platform data so that it's
passed to the panel driver.
Signed-off-by: Archit Taneja <archit@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
The am3517 board file currently requests gpios required to configure the sharp
lq DPI panel, and provides platform_enable/disable callbacks to configure them.
These tasks have been moved to the generic dpi panel driver itself and shouldn't
be done in the board files.
Remove the gpio requests and the platform callbacks from the board file.
Add the gpio information to generic dpi panel's platform data so that it's
passed to the panel driver.
Note: It's not clear why the GPIOs were muxed as input signals in PULL down mode
in am3517_evm_display_init(). Also, only the LCD_PANEL_PWR was toggled in the
platform_enable/disable calls, the generic DPI panel driver will now toggle all
the three gpios on panel's disable/enable. We need to test if these changes to
see if they have any impact or not.
Signed-off-by: Archit Taneja <archit@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Vaibhav Hiremath <hvaibhav@ti.com>
The devkit8000 board file currently requests gpios required to configure the
innolux DPI panel, and provides platform_enable/disable callbacks to configure
them.
These tasks have been moved to the generic dpi panel driver itself and should
be removed from the board files.
Remove the gpio request and the platform callbacks from the board file.
Configure the gpio information in generic dpi panel's platform data so that it's
passed to the panel driver.
Signed-off-by: Archit Taneja <archit@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
The 2430sdp board file currently requests gpios required to configure the NEC
DPI panel, and provides platform_enable/disable callbacks to configure them.
These tasks have been moved to the generic dpi panel driver itself and shouldn't
be done in the board files.
Remove the gpio requests and the platform callbacks from the board file.
Add the gpio information to generic dpi panel's platform data so that it's
passed to the panel driver.
Signed-off-by: Archit Taneja <archit@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
The platform_enable/disable callbacks in board files for VENC omap_dss_device
instances don't do anything. Hence, we can remove these callbacks from the VENC
driver.
Signed-off-by: Archit Taneja <archit@ti.com>
The n8x0 panel driver now manages the gpios required to configure the panel.
This was previously done in panel_n8x0_data's platform_enable/disable callbacks
defined in board files using this panel.
All the board files using this panel now pass the gpio information as platform
data via the panel_n8x0_data struct, which is needed by the panel driver to
configure the gpios connected to the panel. Hence, the uses of
platform_enable/disable ops can be safely removed now.
Signed-off-by: Archit Taneja <archit@ti.com>
The n8x0 panel driver leaves gpio configurations to the platform_enable and
disable calls in the platform's board file. These should happen in the panel
driver itself.
A platform data struct called panel_n8x0_data already exists to hold gpio
numbers and other platform data. However, the gpio requests are expected to be
done in the board file and not the panel driver.
Request all the gpios in the panel driver so that the board files which use
the the panel don't need to do it. This will help in removing the need for the
panel drivers to have platform related callbacks.
Signed-off-by: Archit Taneja <archit@ti.com>
The picodlp panel driver now manages the gpios required to configure the
panel. This was previously done in omap_dss_device's platform_enable/disable
callbacks defined in board files using this panel.
All the board files using this panel now pass the gpio information as platform
data via the panel_generic_dpi_data struct, which is needed by the panel driver
to configure the gpios connected to the panel. Hence, the
platform_enable/disable ops can be safely removed now.
Signed-off-by: Archit Taneja <archit@ti.com>
The picodlp panel driver leaves gpio requests to the platform's board file.
These should happen in the panel driver itself.
A platform data struct called picodlp_panel_data already exists to hold gpio
numbers and other platform data. Request all the gpios in the panel driver so
that the board files which use the the panel don't need to do it.
This will help in removing the need for the panel drivers to have platform
related callbacks.
Signed-off-by: Archit Taneja <archit@ti.com>
The tpo-td043 panel driver now manages the gpios required to configure the panel.
This was previously done in omap_dss_device's platform_enable/disable callbacks
defined in board files using this panel.
All the board files using this panel now pass the gpio information as platform
data via the panel_tpo_td043_data struct, which is needed by the panel driver to
configure the gpios connected to the panel. Hence, the platform_enable/disable
ops can be safely removed now.
Signed-off-by: Archit Taneja <archit@ti.com>
The tpo-td043mtea1 panel driver leaves gpio configurations to the
platform_enable and disable calls in the platform's board file. These should
happen in the panel driver itself.
Create a platform data struct for the panel, this contains the reset gpio
number used by the panel driver, this struct will be passed to the panel driver
as platform data. The driver will request and configure the reset gpio rather
than leaving it to platform callbacks in board files.
This will help in removing the need for the panel drivers to have platform
related callbacks.
Signed-off-by: Archit Taneja <archit@ti.com>
The nec-nl8048 panel driver now manages the gpios required to configure the
panel. This was previously done in omap_dss_device's platform_enable/disable
callbacks defined in board files using this panel.
All the board files using this panel now pass the gpio information as platform
data via the panel_nec_nl8048_data struct, which is needed by the panel driver
to configure the gpios connected to the panel. Hence, the
platform_enable/disable ops can be safely removed now.
Signed-off-by: Archit Taneja <archit@ti.com>
The nec-nl8048hl11-01 panel driver leaves gpio configurations to the
platform_enable and disable calls in the platform's board file. These should
happen in the panel driver itself.
Create a platform data struct for the panel, this contains the gpio numbers
used by the panel driver, this struct will be passed to the panel driver as
platform data. The driver will request and configure these gpios rather than
leaving it to platform callbacks in board files.
This will help in removing the need for the panel drivers to have platform
related callbacks.
Signed-off-by: Archit Taneja <archit@ti.com>
Archit Taneja