At some point things changed so that all the affinity bits can be set,
but cpus_full() macro is not true. This caused problems with the unit
selection logic on multi-unit (board) configurations.
Signed-off-by: Dave Olson <dave.olson@qlogic.com>
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Move the code that shuts down the IB link earlier in the unload
process, to be sure no new packets can arrive while we are unloading.
Signed-off-by: Dave Olson <dave.olson@qlogic.com>
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
To prevent random utility reads and writes of the diag interface to the
chip, we first require a handshake of reading from offset 0 and writing
to offset 0 before any other reads or writes can be done through the
diags device. Otherwise chip errors can be triggered.
Signed-off-by: Dave Olson <dave.olson@qlogic.com>
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
If the chip is no longer usable, LEDs should be turned off so system
can be found easily in the cluster.
Also some minor reorganizing so both chips print hardware error
message at same point and only if there were unrecovered errors
Signed-off-by: Dave Olson <dave.olson@qlogic.com>
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
If the module parameter "kpiobufs" is set too high, the calculation to
reset it to a sane value was incorrect.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
If a receive work request has been removed from the queue but has not
had a CQ entry generated for it and the QP is modified to the error
state, the completion entry generated is incorrect. This patch fixes
the problem.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Code was converted from a &= ~mask to clear_bit, but the bit was left
shifted instead of being used directly, so we were either trashing
memory several pages away, or sometimes taking a kernel page fault on
an invalid page.
Signed-off-by: Dave Olson <dave.olson@qlogic.com>
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Some types of packet errors are moderately common with longer IB
cables and large clusters, and are not reported with prints by other
IB HCA drivers. This suppresses those messages unless the new
__IPATH_ERRPKTDBG bit is set in ipath_debug. Reporting of temporarily
disabled frequent error interrupts was also made clearer
We also distinguish between chip errors, and bad packets sent or
received in the wording of the messages.
Signed-off-by: Dave Olson <dave.olson@qlogic.com>
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The chip documentation on the expected TID vs eager TID parity error
bits was reversed from what was implemented in the RTL, for both
chips. This corrects the definitions.
Signed-off-by: Dave Olson <dave.olson@qlogic.com>
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The loop which initializes the user memory region from an array of
pages was using the wrong limit for the array. This worked OK when
dma_map_sg() returned the same number as the number of pages. This
patch fixes the problem.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This is a sticky state. It is useful for diagnosing problems with
boards versus cable/switch problems.
Signed-off-by: Dave Olson <dave.olson@qlogic.com>
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Eric's changes to the htirq infrastructure require corresponding
modifications to the ipath HT driver code so that interrupts are still
delivered properly.
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Cc: Roland Dreier <rdreier@cisco.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The resize CQ function changes the memory used to store the queue.
Other routines need to honor the lock before accessing the pointer
to the queue and verify that the head and tail are in range.
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This change moves around port assignment so that it happens before any
memory is allocated. This allows memory to be allocated on an appropriate
CPU, which improves performance for users of /dev/ipath.
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The EEPROM is read via programmable I/O pins. When the driver
is compiled -Os, the CPU can speculatively read the I/O
value before it is valid. This patch fixes the problem.
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
We can sometimes trigger parity errors due to processor speculative
reads to our write-combined memory (mostly seen on Woodcrest). Add a
stats counter for these.
Factored out the sendbuffererror buffer cancellation code so it can be
used in the new handling; suppress likely subsequent error messages if
within two jiffies of the cancellation.
Also restore 2 dropped TXE lines on hwe_bitsextant noticed while
debugging.
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The system must be powercycled to clear a HT CRC error; reloading the
driver is not enough.
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
We were passing 0 for base and length, which worked on older kernels,
but it doesn't seem to any longer.
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
If the receiver goes into the error state, we need to flush the
posted receive WQEs.
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Prior to this change, the driver was not able to support a HT and PCIE
card simultaneously present in the same machine.
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Fixed mismatch in linkstate/trainingstate shifts and masks in the
IPATH_IBSTATE_MASK macro. It kept some linktrainingstates
from being printed correctly in debug; no functionality issue unless
I misread the code.
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Don't allow a write to the eeprom from ipathfs unless the write is exactly
128 bytes and starts at offset 0.
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Respond with an error to the SM if our GUID is 0, and don't allow the
user to set our GUID to 0.
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This gives upper-level protocols a chance to unregister while the device
is still usable.
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This allows multiple userspace processes to share a single hardware
context in a master/slave arrangement. It is backwards binary compatible
with existing userspace.
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
If the second allocation failed, the first structure allocated in this
routine was not freed.
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The sender requests an ACK every 1/2 MB to avoid retransmit timeouts that
were causing MVAPICH mod_bw to fail after a predictable number of sends.
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Also added the word "Hardware" after "Fatal" to make it more obvious
that it's hardware, not software.
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This patch only renames files, fixes product names, and updates
comments.
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
When we first submitted a userspace subnet management agent, it was
rejected, so we left it out of the final driver submission. This patch
removes a number of vestigial references to it.
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
A lot of ipath layer code was only called in one place. Now that the
ipath_core and ib_ipath drivers are merged, it's more sensible to simply
inline the simple stuff that the layer code was doing.
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
There is little point in keeping the two drivers separate, so we are
merging them.
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Some userlands try to mmap these pages read-write, so accommodate them.
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Change comment: no longer imply that user can set ipath_kpiobufs to zero.
Actually set ipath_kpiobufs from parameter. Previously only altered
per-device ipath_lastport_piobuf, which was over-written in chip init.
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Allocate enough pointers for all possible ports, to avoid problems in
cleanup/unload.
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Ordering of writethrough store buffers needs to be forced, and we need
to use ifdef to get writethrough behavior to InfiniPath buffers, because
there is no generic way to specify that at this time (similar to code
in char/drm/drm_vm.c and block/z2ram.c).
Signed-off-by: John Gregor <john.gregor@qlogic.com>
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Remove ips namespace from infinipath drivers. This renames ips_common.h to
ipath_common.h. Definitions, data structures, etc. that were not used by
kernel modules have moved to user-only headers. All names including ips have
been renamed to ipath. Some names have had an ipath prefix added.
Signed-off-by: Christian Bell <christian.bell@qlogic.com>
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Cc: "Michael S. Tsirkin" <mst@mellanox.co.il>
Cc: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
We can't tell for sure if any packets are in the infinipath receive buffer
when we shut down a chip port. Normally this is taken care of by orderly
shutdown, but when processes are terminated, or sending process has a bug, we
can continue to receive packets. So rather than writing zero to the address
registers for the closing port, we point it at a dummy memory.
Signed-off-by: Dave Olson <dave.olson@qlogic.com>
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Cc: "Michael S. Tsirkin" <mst@mellanox.co.il>
Cc: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
We do a few more explicit checks for specific models, and now also support the
old PathScale serial number style, or new QLogic style.
This is backwards compatible with previous versions of software and hardware.
That is, older software will see a plausible serial number and correct GUID
when used with a new board, while newer software will correctly handle an
older board.
Signed-off-by: Mike Albaugh <mike.albaugh@qlogic.com>
Signed-off-by: Dave Olson <dave.olson@qlogic.com>
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Cc: "Michael S. Tsirkin" <mst@mellanox.co.il>
Cc: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch separates QP state used for sending and receiving RC packets so the
processing in the receive interrupt handler can be done mostly without locks
being held. ACK packets are now sent without requiring synchronization with
the send tasklet.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Cc: "Michael S. Tsirkin" <mst@mellanox.co.il>
Cc: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The tail register read became redundant as the result of earlier receive
interrupt bug fixes.
Drop another unneeded register read.
And another line that got duplicated.
Signed-off-by: Dave Olson <dave.olson@qlogic.com>
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Cc: "Michael S. Tsirkin" <mst@mellanox.co.il>
Cc: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Do an extra check to see if in-memory tail changed while processing packets,
and if so, going back through the loop again (but only once per call to
ipath_kreceive()). In practice, this seems to be enough to guarantee that if
we crossed the clearing of an interrupt at start of ipath_intr with a
scheduled tail register update, that we'll process the "extra" packet that
lost the interrupt because we cleared it just as it was about to arrive.
Signed-off-by: Dave Olson <dave.olson@qlogic.com>
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Cc: "Michael S. Tsirkin" <mst@mellanox.co.il>
Cc: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The problem was that I was updating the head register multiple times in the
rcvhdrq processing loop, and setting the counter on each update. Since that
meant that the tail register was ahead of head for all but the last update, we
would get extra interrupts. The fix was to not write the counter value except
on the last update.
I also changed to update rcvhdrhead and rcvegrindexhead at most every 16
packets, if there were lots of packets in the queue (and of course, on the
last packet, regardless).
I also made some small cleanups while debugging this.
With these changes, xeon/monty typically sees two openib packets per interrupt
on sdp and ipoib, opteron/monty is about 1.25 pkts/intr.
I'm seeing about 3800 Mbit/s monty/xeon, and 5000-5100 opteron/monty with
netperf sdp. Netpipe doesn't show as good as that, peaking at about 4400 on
opteron/monty sdp. Plain ipoib xeon is about 2100+ netperf, opteron 2900+, at
128KB
Signed-off-by: olson@eng-12.pathscale.com
Signed-off-by: Bryan O'Sullivan <bos@pathscale.com>
Cc: "Michael S. Tsirkin" <mst@mellanox.co.il>
Cc: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Also count the number of interrupts where that works (fastrcvint). On any
interrupt where the port0 head and tail registers are not equal, just call the
ipath_kreceive code without reading the interrupt status, thus saving the
approximately 0.25usec processor stall waiting for the read to return. If any
other interrupt bits are set, or head==tail, take the normal path, but that
has been reordered to handle read ahead of pioavail. Also no longer call
ipath_kreceive() from ipath_qcheck(), because that just seems to make things
worse, and isn't really buying us anything, these days.
Also no longer loop in ipath_kreceive(); better to not hold things off too
long (I saw many cases where we would loop 4-8 times, and handle thousands (up
to 3500) in a single call).
Signed-off-by: Dave Olson <dave.olson@qlogic.com>
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Cc: "Michael S. Tsirkin" <mst@mellanox.co.il>
Cc: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Made in-memory rcvhdrq tail update be in dma_alloc'ed memory, not random user
or special kernel (needed for ppc, also "just the right thing to do").
Some cleanups to make unexpected link transitions less likely to produce
complaints about packet errors, and also to not leave SMA packets stuck and
unable to go out.
A few other random debug and comment cleanups.
Always init rcvhdrq head/tail registers to 0, to avoid race conditions (should
have been that way some time ago).
Signed-off-by: Dave Olson <dave.olson@qlogic.com>
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Cc: "Michael S. Tsirkin" <mst@mellanox.co.il>
Cc: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
These limits are somewhat artificial in that we don't actually have any
device limits. However, the verbs layer expects that such limits exist
and are enforced, so we make up arbitrary (but sensible) limits.
Signed-off-by: Robert Walsh <robert.walsh@qlogic.com>
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Cc: "Michael S. Tsirkin" <mst@mellanox.co.il>
Cc: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
There is no longer a /dev/ipath_diag file; instead, there's
/dev/ipath_diag0, 1, etc.
It's still not possible to have diags run on more than one unit at a time,
but that's easy to fix at some point.
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Cc: "Michael S. Tsirkin" <mst@mellanox.co.il>
Cc: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Bryan O'Sullivan