Provide a way for the user to select which storage to load the LDFW
firmware from, by setting the corresponding environment variables:
- bootdev: block device interface name
- bootdevnum: block device number
- bootdevpart: partition number
This might be useful when the OS is flashed and booted from a different
storage device than eMMC (e.g. USB flash drive). In this case it should
be sufficient to just set:
=> setenv bootdev usb
=> env save
assuming that the USB drive layout follows the same partitioning scheme
as defined in $partitions.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Make it possible to provide the information about storage device where
LDFW firmware resides to the firmware loading routine. The firmware
loader code shouldn't have that data hard-coded anyway, and it also
allows for implementing more dynamic behavior later, like choosing the
storage device containing LDFW via some environment variables.
No functional change.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Make use of PMIC configuration routines and enable all LDOs that might
be useful for bootloader and kernel. The most crucial regulator being
enabled at the moment is LDO24 which provides power to LAN9514 chip.
That makes Ethernet controller and USB hub functional.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Add functions for configuring voltage regulators on S2MPU12 PMIC chip
for E850-96 board. The chip is accessed by commanding APM core (via
ACPM IPC protocol) to perform corresponding transfers over I3C bus.
The most important regulator being set up is LDO24 used for LAN9514 chip
power. As LAN9514 implements USB hub and Ethernet controller
functionality, it's crucial to enable and configure LDO24 to be able to
use it further. While at it, configure the rest of regulators that might
be needed later, both in the bootloader and in kernel.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Add functions to access I3C bus via APM (Active Power Management) core
by using ACPM IPC protocol. It will be further used for configuring PMIC
chip voltage regulators.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Set the environment variable for Ethernet MAC address (ethaddr). Use the
SoC ID to make sure it's unique. It'll be formatted in a way that
follows the consecutive style of the serial number ("serial#" variable),
i.e.:
OTP_CHIPID0 = 0xf51c8113
OTP_CHIPID1 = 0x236
get_chip_id() = 0x236f51c8113
serial# = 00000236f51c8113
ethaddr = 02:36:f5:1c:81:13
where corresponding bytes of the MAC address are:
mac_addr[0] = 0x02 // OTP_CHIPID1[15:8]
mac_addr[1] = 0x36 // OTP_CHIPID1[7:0]
mac_addr[2] = 0xf5 // OTP_CHIPID0[31:24]
mac_addr[3] = 0x1c // OTP_CHIPID0[23:16]
mac_addr[4] = 0x81 // OTP_CHIPID0[15:8]
mac_addr[5] = 0x13 // OTP_CHIPID0[7:0]
because OTP_CHIPID1 has only 16 significant bits (with actual ID
values), and all 32 bits of OTP_CHIPID0 are significant.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
In exynos7420_peric1_get_rate the variable ret is declared as an
'unsigned int' but is then used to receive the return value of
clk_get_by_index which returns an int. The value of ret is then tested
for being less than 0 which will always fail for an unsigned variable.
Fix this by declaring ret as an 'int' so that the test for the error
condition is valid.
This issue was found by Smatch.
Signed-off-by: Andrew Goodbody <andrew.goodbody@linaro.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
The existing compatible name for U-Boot's k3 system controller driver
i.e "ti,am625-system-controller" has been added to linux[1] device-tree.
This compatible in kernel is meant for configuring the Control Module
registers (CTRL_MMR0).
However in U-Boot, the matching driver was being used to load the system
firmware on the secure M-cores by the R5 SPL and therefore must be
updated to a different compatible to avoid conflicts.
Therefore, this patch renames all references of the compatible to
"ti,am654-tisci-rproc-r5". The "-r5" is appended so as to avoid any
future conflicts since r5 specific compatibles should only be useful for
U-Boot.
[1]: 5959618631fe ("dt-bindings: mfd: ti,j721e-system-controller: Add compatible string for AM654")
https://lore.kernel.org/r/20250421214620.3770172-2-afd@ti.com
Signed-off-by: Anshul Dalal <anshuld@ti.com>
Add rauc to bootmeths variable if BOOTMETH_RAUC is enabled.
This is setting a proper default for RAUC enabled systems.
Signed-off-by: Wadim Egorov <w.egorov@phytec.de>
Reviewed-by: Martin Schwan <m.schwan@phytec.de>
Since the bootmeth "rauc" is not a global boot method, do not select the
corresponding BOOTMETH_GLOBAL option.
Signed-off-by: Martin Schwan <m.schwan@phytec.de>
Initially, only one STM32MP25 based board was available, the
stm32mp257f-ev1 board which was set by default in stm32mp25_defconfig.
Since commit 79f3e77133 ("Subtree merge tag 'v6.16-dts' of dts repo [1] into dts/upstream")
we inherited of a second MP25 based board which is the stm32mp257f-dk board.
Enable OF_UPSTREAM_BUILD_VENDOR and set OF_UPSTREAM_VENDOR to allow all
STMicroelectronics DT compilation.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Avoid unlimited while loop by adding a timeout. The timeout is
calculated based on a minimal throughput of 256 KB/s.
The timeout is set at least to 2 seconds.
Signed-off-by: Christophe Kerello <christophe.kerello@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
File system such as YAFFS2 need to know the number of available
OOB bytes per page to be able to choose if they should locate their
metadata in the data area or in the spare area.
Signed-off-by: Christophe Kerello <christophe.kerello@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
In zynqmp_pinconf_set if param is PIN_CFG_IOSTANDARD or
PIN_CONFIG_POWER_SOURCE and zynqmp_pm_pinctrl_get_config returns an
error then value will not be assigned to when its value is tested to be
not equal to arg. Add code to only test value not equal to arg if ret is
false.
This issue was found by Smatch.
Signed-off-by: Andrew Goodbody <andrew.goodbody@linaro.org>
Link: https://lore.kernel.org/r/20250807-pinctrl_misc-v1-4-eeb564a1b032@linaro.org
Signed-off-by: Michal Simek <michal.simek@amd.com>
Use GUSBCFG_FORCEHOSTMODE to detected the HOST forced mode as it is done
in the Linux driver drivers/usb/dwc2/core.c:dwc2_core_reset().
The host polling must be executed only if the current mode is host,
either due to the force HOST mode (which persists after core reset)
or the connector id pin.
The GUSBCFG_FORCEDEVMODE bits is used to force the device mode (for
example used on STM32MP1x platform) and when it is activated the DWC2 reset
failed with the trace:
"dwc2_core_reset: Waiting for GINTSTS_CURMODE_HOST timeout"
Fixes: c5d685b899 ("usb: dwc2: Unify flush and reset logic with v4.20a support")
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Junhui Liu <junhui.liu@pigmoral.tech>
Tested-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Marek Vasut <marek.vasut@mailbox.org>
When the usb node is defined dr_mode="otg" ehci_usb_phy_mode() is called
to determine the mode from status registers.
The IMX95RM does not currently define the USBNC STATUS register but it is
assumed to be an omission as the first three registers are defined.
It has been expirimentally verified that the USBNC_PHY_STATUS register
at offset 0x23C bit4 (USBNC_PHYSTATUS_ID_DIG) reads 0 when USB_ID is GND
and 1 when floating.
Use is_imx9() as this driver works for i.MX91, i.MX93 and i.MX95 and all
of these determine the role based on the USBNC_PHY_STATUS register.
Fixes: 801b5fafd3 "(usb: ehci-mx6: Add i.MX95 support")
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Alice Guo <alice.guo@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Add initial support for i.MX95 USB.30 PHY, which is similar to
the i.MX8MQ and i.MX8MP USB PHY.
The i.MX95 USB3 PHY has a Type-C Assist block (TCA) consisting of two
functional blocks (XBar assist and VBus assist) and is documented
in the i.MX95 RM Chapter 163.3.8 Type-C assist (TCA) block.
Instead of relying on an external MUX for Type-C plug orientation the
XBar can handle the flip internally.
Add initial support for i.MX95 by:
- allowing the driver to be enabled i.MX95
- resetting the XBar
- configuring the TCA in System Configuration mode (which was determined
to be necessary to enable the PHY in device-mode)
Follow-on support will need to be added to steer the XBar based on
either board design (if only one pair is brought out) or if used with a
Type-C controller.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Tested-by: Alice Guo <alice.guo@nxp.com>
In nanddev_init mtd and memorg are assigned values that dereference nand
but this happens before a NULL check for nand. Move the assignments
after the NULL check.
This issue was found by Smatch.
Signed-off-by: Andrew Goodbody <andrew.goodbody@linaro.org>
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Linux features a flash_speed speed test from the mtd-utils suite, U-Boot
does not. Benchmarks are useful for speed improvement developments as
well as troubleshooting or regression testing sometimes.
Enable a benchmark option to enable this feature.
Example of output on a Nuvoton platform:
MA35D1> mtd read nor0 0x81000000 0 0x10000
Reading 65536 byte(s) at offset 0x00000000
MA35D1> mtd read.benchmark nor0 0x81000000 0 0x10000
Reading 65536 byte(s) at offset 0x00000000
Read speed: 3752kiB/s
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
bug fix MTD_OOB_AUTO to MTD_OPS_AUTO_OOB since MTD_OOB_AUTO does not exist
Fixes: dfe64e2c89 ("mtd: resync with Linux-3.7.1")
Signed-off-by: david regan <dregan@broadcom.com>
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
The driver currently does:
mtd->dev->parent = cadence->dev;
This works in Linux because `struct mtd_info` embeds a `struct device`,
so `mtd->dev` is always valid and its `.parent` can be set.
In U-Boot, however, `mtd->dev` is only a pointer to a `struct udevice`.
Dereferencing it before assignment is invalid, which breaks the device
hierarchy. As a result, consumers relying on `mtd->dev` (e.g. partition
parser, reset and re-init paths) operate on a dangling pointer. This
leads to failures during warm reset when the NAND device is accessed
again.
Fix by assigning the device pointer directly:
mtd->dev = cadence->dev;
This matches U-Boot’s device model, preserves a valid hierarchy, and
resolves the warm reset issue on Cadence NAND.
Fixes: ebc41cad ("drivers: mtd: nand: Add driver for Cadence Nand")
Signed-off-by: Dinesh Maniyam <dinesh.maniyam@altera.com>
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Because the early malloc pool size is set to 0x18000, so using this
start address may cause conflict with ATF, then corrupt the heap data.
So we delete the definition to use the default early malloc pool from
CONFIG_SPL_STACK to avoid any conflict
Signed-off-by: Ye Li <ye.li@nxp.com>
Cherry picked from nxp-imx/uboot-imx commit
1ba675df122627a19debe1d807877052705372c6
Jérémie Dautheribes: applied the same patch to the frdm and qsb
imx93-based boards
Signed-off-by: Jérémie Dautheribes <jeremie.dautheribes@bootlin.com>
Fix PHYTEC EEPROM bus mismatch between SPL and U-Boot proper by enabling
CONFIG_SPL_DM_SEQ_ALIAS=y on phyCORE-i.MX93 boards. This way, both the
SPL and U-Boot proper will respect the device-tree aliases for I2C devs
and use the same I2C bus number for phytec_eeprom_data_setup() function
calls. This makes code less confusing and more robust.
Fixes an issue apparent since commit 79f3e77133 ("Subtree merge tag
'v6.16-dts' of dts repo [1] into dts/upstream") where SPL would spew the
following error:
phytec_eeprom_read: i2c EEPROM not found: -110.
phytec_eeprom_data_setup: EEPROM data init failed
While later in U-Boot proper, EEPROM would be successfully read out.
This happens because Linux device-tree for phyBOARD-Segin-i.MX93 since
aforementioned commit enables I2C bus 2 (lpi2c2 is used for audio codec
and RTC) which breaks SPL I2C bus number ordering and I2C EEPROM bus is
shifted by +1. Now, lets prevent this from happening again by utilizing
device-tree aliases also in the SPL.
Signed-off-by: Primoz Fiser <primoz.fiser@norik.com>
On i.MX9 platforms, when booting from USB, the U-Boot environment is
always assumed to be in RAM. However, this causes the boot to hang when
`CONFIG_ENV_IS_NOWHERE` is not enabled. The boot also hangs even if the
environment is present in another storage media (for example, eMMC). Fix
the issue by correctly handling the U-Boot environment's location when
booting from USB. Also for i.MX95, set the environment location based on
the ENV config and not solely based on the boot device type.
Suggested-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: João Paulo Gonçalves <joao.goncalves@toradex.com>
Martin Schwan <m.schwan@phytec.de> says:
This series fixes a segfault, that would occur at the end of scanning a
device, which does not contain the required partition layout scheme for
a RAUC system.
With this series, a "bootflow scan" should now correctly scan the
specified devices with boot method "rauc" without crashing on invalid
partition schemes.
Link: https://lore.kernel.org/r/20250813-wip-bootmeth-rauc-priv-free-v1-0-1ef928169469@phytec.de
The private data struct can be freed when loading the boot script, as we
don't need the slot information anymore at this point.
Signed-off-by: Martin Schwan <m.schwan@phytec.de>
Tested-by: Wadim Egorov <w.egorov@phytec.de>
Move freeing a distro_rauc_priv struct to a new, separate function for
better reuse.
Signed-off-by: Martin Schwan <m.schwan@phytec.de>
Tested-by: Wadim Egorov <w.egorov@phytec.de>
Don't null bootflow->bootmeth_priv, as the private struct is freed later
on by the bootflow.
Signed-off-by: Martin Schwan <m.schwan@phytec.de>
Tested-by: Wadim Egorov <w.egorov@phytec.de>
