The mini u-boot is getting exception because of an initial
stack pointer address is used at near the top of memory,
and while executing u-boot is assigned pre-malloc and
global_data memory after initial stack pointer and updated
the stack pointer. Serial driver is used pre-malloc area
for serial operations before relocation. But pre-malloc area
is cleared while doing BSS at relocation time. The u-boot is
called board_init() function and doing printf, relocation serial
driver is not initialized yet, so it is using before relocation
serial operations but it is cleared by BSS and got the exception.
To fix, change an initial stack pointer address from near the
top of memory to near the relocation memory.
Fixes: 685874939a ("configs: versal: update initial stack pointer")
Signed-off-by: Padmarao Begari <padmarao.begari@amd.com>
Link: https://lore.kernel.org/r/20250407134544.3951763-1-padmarao.begari@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Add support for loading the secure & non-secure pdi images and PL
bitstream on the Versal Gen2 platform. The FPGA driver is enabled
to load the bitstream in PDI format on the AMD Versal Gen2 device.
PDI is the new programmable device image format for Versal Gen2,
and the bitstream for the Versal Gen2 platform is generated exclusively
in this format.
With the enhanced SMC format in TF-A ensuring transparent payload
forwarding for Versal Gen2, the u-boot driver must now handle the
word swapping of PDI address that was previously done in TF-A for
this API. The source code for the Versal2 loadpdi command and the
CONFIG_CMD_VERSAL2 configuration has been removed. It now utilizes
the fpga load <dev> <address> <length> command to load secure &
non-secure pdi images.
Signed-off-by: Prasad Kummari <prasad.kummari@amd.com>
Link: https://lore.kernel.org/r/20250327105200.1262615-3-prasad.kummari@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Add support for loading the secure & non-secure pdi images and
PL bitstream on the Versal NET platform. The FPGA driver is enabled
to load the bitstream in PDI format on the AMD Versal NET device.
PDI is the new programmable device image format for Versal NET,
and the bitstream for the Versal NET platform is generated exclusively
in this format.
The source code for the versalnet loadpdi command and the
CONFIG_CMD_VERSAL_NET configuration has been removed. It now utilizes
the fpga load <dev> <address> <length> command to load secure &
non-secure pdi images.
Signed-off-by: Prasad Kummari <prasad.kummari@amd.com>
Link: https://lore.kernel.org/r/20250327105200.1262615-2-prasad.kummari@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
This device uses the SCSI subsystem to interface with SATA devices.
Trying to use the sata command results in an unhandled exception.
This has the side effect of also causing bootflow scan to raise
an unhandled exception when it attempts to probe the SATA
subsystem. Disabling the sata command fixes this issue and does
not remove support for any boot devices.
Signed-off-by: Benjamin Schneider <ben@bens.haus>
Reviewed-by: Stefan Roese <sr@denx.de>
Testing has shown that loading large initramfs causes data corruption
where the kernel image had been loaded to.
Debian 12 installation using a 17M initramfs boots fine, but the final
system with an initramfs of 27M obscurely fails to boot with bootz
reporting "Bad magic!".
Inspecting kernel_addr_r after this failed boot attempt does show
garbage in place of the expected zimage header.
The problem seems to occur on armada 388 only when sdhci sdma is enabled
in defconfig. Other armada boards such as turris omnia did not enable
the option.
Remove sdhci sdma from defconfig for now as a workaround.
Signed-off-by: Josua Mayer <josua@solid-run.com>
Reviewed-by: Stefan Roese <sr@denx.de>
The Tegra Note 7 is a mini tablet computer and the second Tegra 4
based mobile device designed by Nvidia that runs the Android operating
system. The Tegra Note has a 7" IPS display with 1280 x 800 (217 ppi)
resolution. The 1 GB of RAM and 16 GB of internal memory can be
supplemented with a microSDXC card giving up to 64 GB of additional
storage.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
The ASUS Transformer Pad TF701T is an Android tablet computer made by
ASUS, successor to the ASUS Transformer Pad Infinity. The tablet includes
a Tegra 4 T114 processor clocked at 1.9 GHz, and an upgraded 2560×1600
pixel resolution screen, increasing the pixel density to 300 PPI and
a mobile dock. Transformers (t114) board derives from Nvidia Macallan
development board.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
The Motorola Atrix 4G (MB860) and Droid X2 (MB870) both featured a
dual-core NVIDIA Tegra 2 AP20H processor clocked at 1GHz, coupled with 1GB
of DDR2 RAM. Storage consisted of 16GB of internal flash memory, expandable
via microSD. The display was a 4.0-inch TFT LCD with a resolution of
960x540 pixels (qHD). The devices originally ran on Android up to 2.3
(Gingerbread).
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
GPIO reset and power-off functionality depends on device tree data, which
is often absent in SPL or TPL. To address this, incorporate PHASE_ into the
config option and add Kconfig option or each phase.
Adjust SYSRESET_GPIO and POWEROFF_GPIO uses to address possible
regressions.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
The number of memory banks in QEMU is not bounded by 1.
In this example we have two banks:
qemu-system-aarch64 \
-machine virt \
-nographic \
-cpu cortex-a72 \
-m 8G \
-smp 8,sockets=2,cores=4,threads=1 \
-object memory-backend-ram,id=mem0,size=4G \
-numa node,cpus=0-3,memdev=mem0 \
-object memory-backend-ram,id=mem1,size=4G \
-numa node,cpus=4-7,memdev=mem1 \
-bios u-boot.bin
Use the default value defined in /Kconfig as 4.
Suggested-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Suggested-by: Sughosh Ganu <sughosh.ganu@linaro.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
The AM62x uses the DA8XX (DaVinci) GPIO controller. Enable
CONFIG_DA8XX_GPIO to support GPIO access from the Cortex-A53.
Also enable the 'gpio' command to allow users to interact
with GPIOs from the U-Boot shell.
Signed-off-by: Daniel Schultz <d.schultz@phytec.de>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
This enables the 'rproc' command, allowing users to
start, stop, and manage co-processors as well as load firmware
images.
Useful for systems with auxiliary cores, such as the M4 core
in the AM62x soc.
Signed-off-by: Daniel Schultz <d.schultz@phytec.de>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
This enables the 'rproc' command, allowing users to
start, stop, and manage co-processors as well as load firmware
images.
Useful for systems with auxiliary cores, such as M4 or R5 cores
in the AM64x soc.
Signed-off-by: Daniel Schultz <d.schultz@phytec.de>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Qualcomm changes for v2025.07:
CI: https://source.denx.de/u-boot/custodians/u-boot-snapdragon/-/pipelines/25653
There's been a surprising amount of activity lately on the Qualcomm
side with the two oldest boards getting some fresh attention and a lot
of cleanup and polish going on across the board.
* SDM660 gets USB phy fixes and a pinctrl driver
* The recently added SA8775P/QCS9100 SoC gets a pinctrl driver
* The Qualcomm pinctrl driver now handles reserved pins correctly,
fixing crashes on some boards when running "gpio status -a"
* OF_UPSTREAM_BUILD_VENDOR is enabled in qcom_defconfig
* SDM845 and SC7280 get missing clocks added (since we're now stricter
about those). This gets USB working more reliably in more cases.
* DM_USB_GADGET is enabled for all boards using DWC3 and fasbtoot is
enabled too
* A bug in the livetree fixup code is fixed (making USB work on a lot
more platforms)
* Button label lookup is made case insensitive* bootretry becomes more dynamic, allowing it to be hijacked to make a
"persistent" boot menu that allows dropping to U-Boot shell later on
* A new qcom-phone.config fragment is added along with a phone-specific
default environment and phone-specific debugging/bringup docs. These
make U-Boot more usable on devices without a serial port or keyboard.
* The db820c gets fixed up and updated documentation
* The db410c also gets some love and modernisation as well as a new
reviewer.
* A new driver is added for the USB VBUS regulator found on various
Qualcomm PMICs
* The Qualcomm SPMI driver gets some fixes and cleanup for SPMI v5 and
v7 support.
Move the default bootcmd from the defconfig to the board environment in
preparation for RAUC support. No change in functionality.
Signed-off-by: Leonard Anderweit <l.anderweit@phytec.de>
Signed-off-by: Primoz Fiser <primoz.fiser@norik.com>
This is a new DM core helper. There is now a graph endpoint
representation in the sandbox test DTS, so we can just use it to verify
the helper proper behavior.
Suggested-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Add support for ethernet boot in the A53 SPL. Increase the SPL Size
limit and update SPL_STACK_R_ADDR.
Signed-off-by: Wadim Egorov <w.egorov@phytec.de>
Provide a defconfig for booting the phycore-am62x via Ethernet.
We need a separate defconfig because the AM62x has not enough internal
SRAM to support all boot sources.
Signed-off-by: Wadim Egorov <w.egorov@phytec.de>
Currently the msm_sdhci doesn't yet support DLL configurations which are
required to enable bus speeds greater that 100MHz. So disable HS200 mode
support as of now as it requires bus speeds of 200MHz.
This should fix eMMC issues reported on RB1/RB2 although it should fix
issues for all Qcom platforms but it's not seen there as mostly SD cards
available don't support HS200 mode. The SD cards usually works in high
speed mode whose performance remains unaffected by this change. It only
affects RB1/RB2 as eMMC flash on these support HS200 mode but the U-Boot
driver currently is incapable of supporting that.
Reviewed-by: Caleb Connolly <caleb.connolly@linaro.org>
Signed-off-by: Sumit Garg <sumit.garg@oss.qualcomm.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20250410080027.208674-2-sumit.garg@kernel.org
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Enable fastboot support over USB, using MMC as the backend. This will be
the internal eMMC on devices that have it, or the sdcard slot on devices
with UFS (if available).
We don't use a fixed address for the fastboot buffer because it's
allocated at runtime per-board. Entering fastboot mode should be done by
executing "run fastboot" or manually running:
fastboot -l $fastboot_addr_r usb 0
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20250324-sdm845-fixes-fastboot-v1-4-d177a10f336d@linaro.org
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Note that this undoes the changes of commit cf6d4535cc ("x86:
emulation: Disable bloblist for now") as that was intended only for the
release due to time.
Currently in j721e_init.c we check which firewalls to remove using
the board configuration (e.g CONFIG_TARGET_J721E_R5_EVM). We do this
as J721e and J7200 have different IP and firewalls but use the same
SoC definition (SOC_K3_J721E) even though they are different SoCs.
The idea was they would be similar enough that they both could use
the same SoC config to help with common code sharing. Board checks
would then be used differentiate.
This has grown far too messy to maintain any more, especially now
that there is more than one board using J721e (EVM, SK, Beagle AI64).
As differentiation is done based on board, every one of these boards
would have to have checks added for them. Instead let's split J7200
support out from J721e like how normal new SoC support is done.
This patch touches several subsystems and could not be split much better
as when we add SOC_K3_J7200 we want to make use of it in all spots that
once used the combined SOC_K3_J721E so we can turn off SOC_K3_J721E when
building for J7200 boards.
Signed-off-by: Andrew Davis <afd@ti.com>
MUX_MMIO is required in SPL stage in order to boot hyperflash
successfully. Add configs to enable MUX_MMIO in SPL stage.
Signed-off-by: Anurag Dutta <a-dutta@ti.com>
MUX_MMIO is required in SPL stage in order to boot hyperflash
successfully. Add configs to enable MUX_MMIO in SPL stage.
Signed-off-by: Anurag Dutta <a-dutta@ti.com>
