Adjust legoev3_defconfig to reduce the binary output size.
As u-boot has bloated a bit over the years, the legoev3_defconfig can no
longer build something that fits in the 256kB size limit of the EV3.
This drops a few unused features, but the real difference-makers are
enabling thumb instructions and using link time optimization to reduce
the size.
This reduced u-boot.bin from 279,920 to 198,416 bytes on my local
machine with arm-none-eabi-gcc (15:13.2.rel1-2) 13.2.1 20231009.
HAS_BOARD_SIZE_LIMIT is also added to catch any future regressions.
Signed-off-by: David Lechner <david@lechnology.com>
The mx6sabresd U-Boot proper binary size has grown beyond the
CONFIG_BOARD_SIZE_LIMIT.
Reduce its size by removing the CONFIG_MULTI_DTB_FIT, BOOTM_PLAN9 and
BOOTM_RTEMS options.
According to doc/README.multi-dtb-fit:
"Usually the DTB is selected by the SPL and passed down to U-Boot. But some
platforms don't use the SPL. In this case MULTI_DTB_FIT can used to provide
U-Boot with a choice of DTBs"
mx6sabresd uses SPL, so MULTI_DTB_FIT can be safely dropped as the DTB
selection in SPL is done by board_fit_config_name_match().
Tested boot on the imx6dl and imx6q variants.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Select PINCTRL_TH1520 in CPU Kconfig entry and update defconfig for
existing TH1520-based boards to ensure PINCTRL is enabled.
Signed-off-by: Yao Zi <ziyao@disroot.org>
Acked-by: Leo Yu-Chi Liang <ycliang@andestech.com>
The commit c69103218e ("i2c: mxc_i2c: add DM_FLAG_PRE_RELOC flag")
has enabled by default the i2c initialization in the pre-relocation
phase.
It turned out that vf610 based boards had too small SYS_MALLOC_F_LEN
pool size.
As a solution the explicit value of CONFIG_SYS_MALLOC_F_LEN for all
vf610 based boards has been removed from their configs.
Instead, the default value of 0x2000 is now used, which causes boards
to work correctly again. This approach has been tested on BK4 device.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Capsule update is EFI based firmware update which is widely
used in various OS distributions. This feature is required
by ARM System-Ready compliance test. So
- Define image array and GUID
- Select configs for EFI Capsule update
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Capsule update is EFI based firmware update which is widely
used in various OS distributions. This feature is required
by ARM System-Ready compliance test. So
- Define image array and GUID
- Select configs for EFI Capsule update
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Capsule update is EFI based firmware update which is widely
used in various OS distributions. This feature is required
by ARM System-Ready compliance test. So
- Define image array and GUID
- Select configs for EFI Capsule update
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Capsule update is EFI based firmware update which is widely
used in various OS distributions. This feature is required
by ARM System-Ready compliance test. So
- Define image array and GUID
- Select configs for EFI Capsule update
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Capsule update is EFI based firmware update which is widely
used in various OS distributions. This feature is required
by ARM System-Ready compliance test. So
- Define image array and GUID
- Select configs for EFI Capsule update
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Ilias Apalodimas <ilias.apalodimas@linaro.org> says:
Instructions that lead ito an exception in the hypervisor can't modify two
CPU registers at once for the ARM ISA.
These instructions cannot be emulated by KVM as they do not produce
syndrome information data that KVM can use to infer the destination
register, the faulting address, whether it was a load or store, or
if it's a 32 or 64 bit general-purpose register.
As a result an external abort is injected from QEMU, via ext_dabt_pending.
Link: https://lore.kernel.org/r/20250618065828.1312146-1-ilias.apalodimas@linaro.org
We recently added IO accessors that will work with KVM for any MMIO
access that casues an exception to the hypervisor. Enable them by
default for QEMU.
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Tested-by: Mikko Rapeli <mikko.rapeli@linaro.org>
Enable support for R-Car Gen4 PCIe controller and NVMe storage
on Retronix R-Car V4H Sparrow Hawk board .
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Hrushikesh Salunke <h-salunke@ti.com> says:
This series adds support for the Endpoint mode on Cadence PCIe controller
on TI's K3 family of SoCs. The driver is an adaptation of the Linux
driver (drivers/pci/controller/cadence/pci-j721e.c) and has been
implemented specifically for Endpoint mode of operation on AM64X. A minor
set of changes will be sufficient to support other K3 SoCs as well.
This patch is tested on AM64X EVM. Following are the log corresponding
to this feature.
https://gist.github.com/hrushikesh221/e8557cbe7667877c50f7d7e9bb96d060
Link: https://lore.kernel.org/r/20250616164929.631791-1-h-salunke@ti.com
TI's AM64x SoC has a single instance of PCIe Controller namely PCIe0
which is a Cadence PCIe Controller. To support PCI Endpoint
functionality with the PCIe0 instance of PCIe, enable the corresponding
configs.
Signed-off-by: Hrushikesh Salunke <h-salunke@ti.com>
Use default value of malloc size coming from Kconfig, instead of
board specific override.
Signed-off-by: Udit Kumar <u-kumar1@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
This concludes support for the Allwinner A133 SoC, the biggest chunk of
which is the DRAM init code. Also includes support for a devboard using
this SoC, the DT of which got added to the kernel only recently. The
same is true for another H618 devboard, so add the respective devconfig
as well.
Gitlab CI passed, and I booted that briefly on those two boards.
This PR introduces 3 new platforms, two from the new Dragonwing IQx
series (QCS615 and QCS8300) as well as the IPQ5424.
Additionally:
* Support for booting downstream Android boot images on some phones is
added
* Capsule update support is expanded to be more generic, determining
which partition U-Boot was flashed to automatically and supporting
many more boards.
* Minor capsule update bugs are fixed
* A watchdog driver is added and gets timeout support
* Autoboot now requires pressing "space" specifically to stop booting as
a workaround for some boards getting rogue key presses which would
cause autoboot to fail
* Documentation is added for the Dragonwing boards
* The RB1/2 now use USB gadget mode rather than host
* A bug is fixed where GPIO reads could return incorrect values
The Chameleon board is an OpenHardware devboard made by YuzukiTsuru,
featuring an Allwinner H616 SoC. The form factor resembles the Raspberry
Pi Model A boards, though it differs significantly in its features.
Apart from the usual peripherals of those kind of boards (SD card, eMMC,
WiFi, HDMI), it features four USB-C 2.0 ports.
Add a defconfig for the board, the DRAM parameters have been extracted
from the firmware shipped with the board.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
The Liontron H-A133L is an industrial development board based on the
Allwinner A133 SoC. It uses LPDDR4 DRAM, eMMC, and an AXP707 PMIC.
Add a defconfig with the required DRAM settings.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
As stated in 5e847f7729 ("efi_loader: call efi_init_early() earlier"):
efi_init_early() creates an event hook for block device probing.
It has to be called before any block device is probed.
Indeed, efi_bl_init() registers EVT_DM_POST_PROBE event, which calls
efi_disk_probe() whenever any block device is probed. And to make that
hook work, the initialization of all block devices was put after
efi_init_early() in initcall_run_r():
INITCALL(efi_init_early);
INITCALL(initr_nand);
INITCALL(initr_onenand);
INITCALL(initr_mmc);
Because LDFW firmware is being read from MMC, attempt to load LDFW in
board_init() causes MMC driver to be probed. And because board_init() is
executed before efi_init_early(), the hook mentioned above won't work
for MMC devices anymore. So EFI disk objects won't be created, which in
turn makes the EFI subsystem non-functional, showing next symptoms:
- 'efidebug dh' output is empty
- attempt to add boot devices in 'eficonfig' shows this message:
"No block device found!"
- 'bootefi selftest $fdtcontroladdr' shows this warning:
"Cannot persist EFI variables without system partition"
- booting GRUB with 'bootefi' runs minimal GRUB shell which doesn't
see any block devices as well, probably because EFI vars weren't
passed
Load LDFW in board_late_init() instead, as it's called after
efi_init_early(). This fixes the described problem and makes it possible
to run EFI apps like GRUB correctly, add entries in 'eficonfig', and
makes 'efivar --list' command in Linux rootfs actually show EFI
variables.
The only user of LDFW at the moment is the TRNG driver, and it's probed
later, only when it's going to be used (e.g. on "rng" command). So it's
fine to load LDFW in board_late_init(). Now the corresponding call order
will look like this:
efi_init_early()
initr_mmc()
mmc_probe()
EVT_DM_POST_PROBE -> efi_disk_probe()
board_late_init()
load_ldfw() -> fs_read(), blk_dread()
exynos_trng_probe()
Fixes: ccfd8de541 ("board: samsung: e850-96: Report LDFW loading failures")
Fixes: f04e58cc97 ("board: samsung: e850-96: Load LDFW firmware on board init")
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Rename the variable and add ENV_ prefix, so that all configuration
options which are related to environment would have an CONFIG_ENV_
prefix. No functional change.
Also rename USE_DEFAULT_ENV_FILE to USE_ENV_DEFAULT_ENV_TEXT_FILE .
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Rename the variable and add ENV_ prefix, so that all configuration
options which are related to environment would have an CONFIG_ENV_
prefix. No functional change.
Use ENV_MMC_EMMC_HW_PARTITION to clarify this is the eMMC hardware
partition selector, not a software partition table entry selector.
Retain the ENV_MMC_ prefix to make it easier to search for all the
SD/MMC related ENV options. Update the help text accordingly.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Rename the variable and add ENV_ prefix, so that all configuration
options which are related to environment would have an CONFIG_ENV_
prefix. No functional change.
Use ENV_MMC_DEVICE_INDEX to clarify this is the SD/MMC device
index, a number, as enumerated by U-Boot. Update the help text
accordingly.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Rename the variable and add ENV_ prefix, so that all configuration
options which are related to environment would have an CONFIG_ENV_
prefix. No functional change.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Rename the variable and add ENV_ prefix, so that all configuration
options which are related to environment would have an CONFIG_ENV_
prefix. No functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Rename the variable and add ENV_ prefix, so that all configuration
options which are related to environment would have an CONFIG_ENV_
prefix. No functional change.
Reviewed-by: Quentin Schulz <quentin.schulz@cherry.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
The CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0xeb300000 does not make it into
board .config on either R-Car V4H White Hawk or Sparrow Hawk, remove
this configuration option. The early SPL stack is however pointing
into the RT-VRAM and may corrupt payload loaded into the RT-VRAM by
the BootROM. Set the early SPL stack at fixed location at the end of
System RAM instead, where it cannot interfere with the payload loaded
into RT-VRAM.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Raspberry Pi 5 can now have up to 16 GiB of RAM where the memory spans 8
DRAM banks in total. Increase the config value to 8 to initialize the
whole RAM. Without this change, kernel only sees 8 GiB of RAM on the 16
GiB CM5 as reported in [1].
[1] https://github.com/home-assistant/operating-system/issues/3989
Signed-off-by: Jan Čermák <sairon@sairon.cz>
Reviewed-by: Matthias Brugger <mbrugger@suse.com>
E Shattow <e@freeshell.de> says:
Make consistent use of lowercase hexadecimal prefix '0x' throughout U-Boot.
There are a few remaining uses of uppercase 'X' to denote hexadecimal prefix
or placeholder in documentation and error messages.
External devicetree-rebasing dts/upstream and the generated code of
xilinx/zynq are ignored for the series.
Link: https://lore.kernel.org/r/20250606224558.1117422-1-e@freeshell.de
When the toradex-smarc-imx8mp_defconfig file was first added, SPL_STACK
was set to 0x960000, but SPL_HAVE_INIT_STACK wasn't enabled.
This led to SPL_STACK being correctly dropped in commit 25fefa05d7
("configs: Resync with savedefconfig"), since SPL_HAVE_INIT_STACK was
missing, which ended up making the board not boot.
Fix this by adding SPL_STACK back and making sure SPL_HAVE_INIT_STACK is
enabled.
Fixes: dde53eae88 ("board: toradex: add Toradex SMARC iMX8MP")
Signed-off-by: Hiago De Franco <hiago.franco@toradex.com>
Acked-by: Francesco Dolcini <francesco.dolcini@toradex.com>
After enabling some options to support EEPROM read in SPL
(CONFIG_SPL_I2C_EEPROM), the following error appears:
alloc space exhausted
Increasing SYS_MALLOC_F_LEN from 8kB to 64kB fixes the problem.
But instead of manually increasing the value, adopt method used in
commit ce3f23404c ("board: bsh: imx8mn_bsh_smm_s2/s2pro: enlarge
CONFIG_SPL_SYS_MALLOC_F_LEN"):
Dropping CONFIG_SPL_SYS_MALLOC_F_LEN option allows it to be set to the
default value of CONFIG_SYS_MALLOC_F_LEN, which is set by default to 64kB
(0x10000) on i.MX8M platforms.
Suggested-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
