Agilex5 FSBL is required to disable the power of unused peripheral SRAM
blocks to reduce power consumption.
Introducing a new power manager driver for Agilex5 which will be called
as part of Agilex5 SPL initialization process.
This driver will read the peripheral handoff data obtained from the
bitstream and will power off the specified peripheral's SRAM from the
handoff data values.
Signed-off-by: Alif Zakuan Yuslaimi <alif.zakuan.yuslaimi@altera.com>
Reviewed-by: Tien Fong Chee <tien.fong.chee@altera.com>
The X-Powers AXP323 is very close sibling to the AXP313A, only that it
adds support for dual-phasing the first two DC/DC converters.
We do not really care about this particular feature, so just add the new
compatible string and tie it to the existing AXP313A support code.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
CI: https://source.denx.de/u-boot/custodians/u-boot-imx/-/pipelines/27149
- Add support for the NXP imx93 frdm board.
- imx93_evk and phycore-imx93 cleanups.
- Convert imx6dl-sielaff to OF_UPSTREAM and fix serial download mode boot.
- Fix crash in imx power-domain.
- Migrate Phytec imx8mm boards to standard boot.
- Fix smatch warnings.
uclass_find_next_device always returns 0, so instead make it a void and
update calling sites.
Signed-off-by: Andrew Goodbody <andrew.goodbody@linaro.org>
In case of the i.MX8M power-domains (i.MX8MQ, MM, MN) there is only
one power-domain for each device. Therefore the 'id' field in struct
power_domain should always be zero.
Currently if a power-domain is accessed after the initial bind, the
'id' field is left uninitialized. This didn't cause any problems
until the following commits were introduced:
9086b64ca0 ("power-domain: Add support for refcounting (again)")
a785ef2448 ("imx: power-domain: Enable refcounting on imx8mp")
Now the 'id' field gets accessed in the power_domain_off() sequence
and the invalid value causes "Synchronous Abort" failures.
This was observed on a i.MX8MM board when running "usb start" and
then "usb stop".
Fix this issue by setting power_domain->id to '0' in
imx8m_power_domain_of_xlate().
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Fixes: d08a194871 ("imx: add support for i.MX8MQ power domain controller")
Fixes: 9086b64ca0 ("power-domain: Add support for refcounting (again)")
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
E Shattow <e@freeshell.de> says:
Make consistent use of lowercase hexadecimal prefix '0x' throughout U-Boot.
There are a few remaining uses of uppercase 'X' to denote hexadecimal prefix
or placeholder in documentation and error messages.
External devicetree-rebasing dts/upstream and the generated code of
xilinx/zynq are ignored for the series.
Link: https://lore.kernel.org/r/20250606224558.1117422-1-e@freeshell.de
Use consistent lowercase hex prefix style in drivers/*
Does not change hex prefix case in allcaps uppercase style error messages
Signed-off-by: E Shattow <e@freeshell.de>
The val (the bits to set) is the second member of the reg_data structure
and mask the third one. We obviously want to clear bits 6 and 7 in order
to only set bit 7 in there instead of only clearing bit 7 in order to
write bits 6 and 7 (which makes no sense).
Fortunately, according to the datasheet, bit 6 value doesn't matter when
bit 7 is set so this is essentially just a cosmetic change, no intended
change in behavior.
Fixes: f172575d92 ("power: rk8xx: add support for RK806")
Signed-off-by: Quentin Schulz <quentin.schulz@cherry.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Allows use of the regulator functions of the RK8XX PMIC in SPL, which is
necessary to support the functionality of the Rockchip IO-domain driver
on relevant platforms.
Signed-off-by: Justin Klaassen <justin@tidylabs.net>
Reviewed-by: Quentin Schulz <quentin.schulz@cherry.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The include file <command.h> does not need anything from <env.h>.
Furthermore, include/env.h itself includes other headers which can lead
to longer indirect inclusion paths. To prepare to remove <env.h> from
<command.h> fix all of the places which had relied on this indirect
inclusion to instead include <env.h> directly.
Reviewed-by: Mattijs Korpershoek <mkorpershoek@kernel.org> # android, bcb
Reviewed-by: Jerome Forissier <jerome.forissier@linaro.org> # spawn
Signed-off-by: Tom Rini <trini@konsulko.com>
This file was using IS_ENABLED() to test for CONFIG flags but omitted
the CONFIG_ prefix and so did not work as expected.
Signed-off-by: Tom Rini <trini@konsulko.com>
MAX8907 PMIC has embedded poweroff function used by some device to initiane
device power off. Implement it as optional sysreset driver guarded by
kconfig option and system-power-controller device tree property.
Tested-by: Ion Agorria <ion@agorria.com>
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Added a new regulator driver for the MAXIM MAX8907 PMIC, providing
essential regulator functionalities and incorporated the necessary binding
framework within the core PMIC driver.
Tested-by: Ion Agorria <ion@agorria.com>
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
If there is a SoC specific SCMI protocol driver, using
scmi_proto_driver_get() function can avoid to add SoC specific code to
scmi_agent-uclass.c.
Signed-off-by: Alice Guo <alice.guo@nxp.com>
AXP PMICs have a pin which can either report the USB VBUS state, or
driving a regulator that supplies USB VBUS. Add a regulator driver for
controlling this pin. The selection between input and output is done via
the x-powers,drive-vbus-en pin on the PMIC (parent) node.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Prevent enabling/disabling multiple times the same power domain to avoid
breakages due to the same power domains being referenced several times
by different device nodes.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
It is very surprising that such an uclass, specifically designed to
handle resources that may be shared by different devices, is not keeping
the count of the number of times a power domain has been
enabled/disabled to avoid shutting it down unexpectedly or disabling it
several times.
Doing this causes troubles on eg. i.MX8MP because disabling power
domains can be done in recursive loops were the same power domain
disabled up to 4 times in a row. PGCs seem to have tight FSM internal
timings to respect and it is easy to produce a race condition that puts
the power domains in an unstable state, leading to ADB400 errors and
later crashes in Linux.
Some drivers implement their own mechanism for that, but it is probably
best to add this feature in the uclass and share the common code across
drivers. In order to avoid breaking existing drivers, refcounting is
only enabled if the number of subdomains a device node supports is
explicitly set in the probe function. ->xlate() callbacks will return
the power domain ID which is then being used as the array index to reach
the correct refcounter.
As we do not want to break existing users while stile getting
interesting error codes, the implementation is split between:
- a low-level helper reporting error codes if the requested transition
could not be operated,
- a higher-level helper ignoring the "non error" codes, like EALREADY and
EBUSY.
CI tests using power domains are slightly updated to make sure the count
of on/off calls is even and the results match what we *now* expect. They
are also extended to test the low-level functions.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The current code attempts to bind scmi_voltage_domain to regulator subnode
of the SCMI protocol node, so scmi_voltage_domain can then bind regulators
directly to subnodes of its node. This kind of behavior should not be in
core code, move it into scmi_voltage_domain driver code. Let the driver
descend into regulator node and bind regulators to its subnodes.
Fixes: 1f213ee4db ("firmware: scmi: voltage regulator")
Signed-off-by: Marek Vasut <marex@denx.de>
[Alice Guo: Fix scmi_regulator_bind]
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The CPCAP is a Motorola/ST-Ericsson creation, a multifunctional IC whose
main purpose was power control. It was used in a wide variety of Motorola
products, both Tegra and OMAP based. The most notable devices using this
PMIC are the Motorola Droid 4, Atrix 4G, and Droid X2.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Tom Rini <trini@konsulko.com> says:
This series switches to always using $(PHASE_) in Makefiles when
building rather than $(PHASE_) or $(XPL_). It also starts on documenting
this part of the build, but as a follow-up we need to rename
doc/develop/spl.rst and expand on explaining things a bit.
Link: https://lore.kernel.org/r/20250401225851.1125678-1-trini@konsulko.com
It is confusing to have both "$(PHASE_)" and "$(XPL_)" be used in our
Makefiles as part of the macros to determine when to do something in our
Makefiles based on what phase of the build we are in. For consistency,
bring this down to a single macro and use "$(PHASE_)" only.
Signed-off-by: Tom Rini <trini@konsulko.com>
Qualcomm changes for v2025.07:
CI: https://source.denx.de/u-boot/custodians/u-boot-snapdragon/-/pipelines/25653
There's been a surprising amount of activity lately on the Qualcomm
side with the two oldest boards getting some fresh attention and a lot
of cleanup and polish going on across the board.
* SDM660 gets USB phy fixes and a pinctrl driver
* The recently added SA8775P/QCS9100 SoC gets a pinctrl driver
* The Qualcomm pinctrl driver now handles reserved pins correctly,
fixing crashes on some boards when running "gpio status -a"
* OF_UPSTREAM_BUILD_VENDOR is enabled in qcom_defconfig
* SDM845 and SC7280 get missing clocks added (since we're now stricter
about those). This gets USB working more reliably in more cases.
* DM_USB_GADGET is enabled for all boards using DWC3 and fasbtoot is
enabled too
* A bug in the livetree fixup code is fixed (making USB work on a lot
more platforms)
* Button label lookup is made case insensitive* bootretry becomes more dynamic, allowing it to be hijacked to make a
"persistent" boot menu that allows dropping to U-Boot shell later on
* A new qcom-phone.config fragment is added along with a phone-specific
default environment and phone-specific debugging/bringup docs. These
make U-Boot more usable on devices without a serial port or keyboard.
* The db820c gets fixed up and updated documentation
* The db410c also gets some love and modernisation as well as a new
reviewer.
* A new driver is added for the USB VBUS regulator found on various
Qualcomm PMICs
* The Qualcomm SPMI driver gets some fixes and cleanup for SPMI v5 and
v7 support.
Add support for the i.MX8 MEDIAMIX domain which is driving the power
over the whole display/rendering pipeline.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
It is very surprising that such an uclass, specifically designed to
handle resources that may be shared by different devices, is not keeping
the count of the number of times a power domain has been
enabled/disabled to avoid shutting it down unexpectedly or disabling it
several times.
Doing this causes troubles on eg. i.MX8MP because disabling power
domains can be done in recursive loops were the same power domain
disabled up to 4 times in a row. PGCs seem to have tight FSM internal
timings to respect and it is easy to produce a race condition that puts
the power domains in an unstable state, leading to ADB400 errors and
later crashes in Linux.
CI tests using power domains are slightly updated to make sure the count
of on/off calls is even and the results match what we *now* expect.
As we do not want to break existing users while stile getting
interesting error codes, the implementation is split between:
- a low-level helper reporting error codes if the requested transition
could not be operated,
- a higher-level helper ignoring the "non error" codes, like EALREADY and
EBUSY.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Currently in j721e_init.c we check which firewalls to remove using
the board configuration (e.g CONFIG_TARGET_J721E_R5_EVM). We do this
as J721e and J7200 have different IP and firewalls but use the same
SoC definition (SOC_K3_J721E) even though they are different SoCs.
The idea was they would be similar enough that they both could use
the same SoC config to help with common code sharing. Board checks
would then be used differentiate.
This has grown far too messy to maintain any more, especially now
that there is more than one board using J721e (EVM, SK, Beagle AI64).
As differentiation is done based on board, every one of these boards
would have to have checks added for them. Instead let's split J7200
support out from J721e like how normal new SoC support is done.
This patch touches several subsystems and could not be split much better
as when we add SOC_K3_J7200 we want to make use of it in all spots that
once used the combined SOC_K3_J721E so we can turn off SOC_K3_J721E when
building for J7200 boards.
Signed-off-by: Andrew Davis <afd@ti.com>
Manorit Chawdhry <m-chawdhry@ti.com> says:
The series adds support for J742S2 family of SoCs. Also adds J742S2 EVM
Support and re-uses most of the stuff from the superset device J784s4.
This device is a subset of J784S4 and shares the same memory map and
thus the code is being reused from J784S4 to avoid duplication.
It initially cleans up the J784s4 and AM69 files so that they can be
re-usable for j742s2 and then it introduces J742S2.
The DT for the following SoC will be coming to U-boot during 6.13 Sync
so the series is kept as RFC till then.
Here are some of the salient features of the J742S2 automotive grade
application processor:
The J742S2 SoC belongs to the K3 Multicore SoC architecture platform,
providing advanced system integration in automotive, ADAS and industrial
applications requiring AI at the network edge. This SoC extends the K3
Jacinto 7 family of SoCs with focus on raising performance and
integration while providing interfaces, memory architecture and compute
performance for multi-sensor, high concurrency applications.
Some changes that this devices has from J784S4 are:
* 4x Cortex-A72 vs 8x Cortex-A72
* 3x C7x DSP vs 4x C7x DSP
* 4 port ethernet switch vs 8 port ethernet switch
* 2 DDR controller vs 4 DDR controller
Test logs:
https://gist.github.com/manorit2001/f7df0e8cca1e9973b4361f0559c6f53d
Link: https://lore.kernel.org/r/20250317-b4-upstream-j742s2-v4-0-4ba88bfd357a@ti.com
Re-use j784s4 clocks and power domains for j742s2 family of device.
Reviewed-by: Udit Kumar <u-kumar1@ti.com>
Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
Some of the X-Power AXP PMICs can be ordered with an alternative I2C
address, for instance an AXP717 could be shipped with address 0x34 or
with address 0x35. Similarly the AXP803 lists two possible addresses.
For DM (DT) based drivers this is no problem, but the Allwinner SPL
code relies on exactly one hardcoded address per PMIC so far.
Add a Kconfig variable that holds the I2C address used by the PMIC
accessed in the SPL, and provide the (mostly only one) supported address
as its default, for the PMICs we use. Boards using the other address
can easily set this in their defconfig.
This effectively moves the hardcoding from C code to Kconfig.
That enables to use the AXP717 on some boards with the new Allwinner
A523 chip, which use the other I2C address there.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
The AXP803 has been around for about a decade now, but so far we didn't
need SPL support, since the DRAM rail was wired up correctly at reset.
Now some boards using the A133 SoC use the (compatible) AXP707 with DDR4
memory, which requires the SPL to set the required 1.1V voltage manually.
Add the descriptions for the DC/DC regulators of the AXP803, and enable
that when CONFIG_AXP803_POWER is enabled.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
As per TRM[0] Section 8.7.1 "TPS6594-Q1 Registers", LDOx_Vout
bit 6-1, define the NVM voltage settings.
Along side table 8-4 of above TRM, shows voltage to value mapping.
Driver wrongly using bits 5-1 to calculate voltage, and to convert
voltage to value driver was using buck's calculation.
So fix those calculation.
[0]: https://www.ti.com/lit/ds/symlink/tps6594-q1.pdf
Fixes: 5d7dbd22cf ("power: regulator: tps65941: use function callbacks for conversion ops")
Signed-off-by: Udit Kumar <u-kumar1@ti.com>
Reviewed-by: Neha Malcom Francis <n-francis@ti.com>
Bind SYSRESET child to parent node since it does not have
its own node in the device tree.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Bind GPIO and SYSRESET children to parent node since they
do not have their own nodes in the device tree.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Fix compatiable name for TPS65224 PMIC as defined in
dts/upstream/Bindings/mfd/ti,tps6594.yaml bindings.
Fixes: 1468fbba6d55("power: pmic: tps65941: Add TI TPS65224 PMIC")
Signed-off-by: Udit Kumar <u-kumar1@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Replace magic numbers in buckval2votl() & buckvolt2val() with macros to
help with clarity and correlate what the numbers correspond to in the
TPS65219 datasheet.
Signed-off-by: Shree Ramamoorthy <s-ramamoorthy@ti.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Replace printf() with pr_err() because pr_err() has a uniform print format
and takes into consideration the log levels supported.
Signed-off-by: Shree Ramamoorthy <s-ramamoorthy@ti.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
