Kalle Valu says:
====================
wireless-drivers-next patches for 5.3
First set of patches for 5.3, but not that many patches this time.
This pull request fails to compile with the tip tree due to
ktime_get_boot_ns() API changes there. It should be easy for Linus to
fix it in p54 driver once he pulls this, an example resolution here:
https://lkml.kernel.org/r/20190625160432.533aa140@canb.auug.org.au
Major changes:
airo
* switch to use skcipher interface
p54
* support boottime in scan results
rtw88
* add fast xmit support
* add random mac address on scan support
rt2x00
* add software watchdog to detect hangs, it's disabled by default
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit ec8f24b7fa ("treewide: Add SPDX license identifier -
Makefile/Kconfig") marked various Makefiles and Kconfig files within ath
directories as GPL-2.0. But these modules and drivers are actually ISC:
* ath
* ar5523
* ath10k
* ath5k
* ath6kl
* ath9k
* wcn36xx
* wil6210
Fix SPDX tags accordingly.
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Integrated WiFi chipset ex:WCN399x supports fw logging
using WMI copy engine and shared mem DIAG based fw logging.
By default shared mem DIAG based fw logging is enabled.
To support WMI copy engine based fw logging add QMI
control message to enable WMI copy engine based fw logging.
Enable WMI based fw logging using fw_diag_log module parameter.
insmod ath10k_core.ko fw_diag_log=1
DIAG utility(https://github.com/andersson/diag) implements extraction
of diagnostics related messages between application processor and
various subsystems while shared mem DIAG based fw logging is enabled.
Testing: Tested on WCN3990/QCA6174 HW
Tested FW: WLAN.HL.3.1-00959-QCAHLSWMTPLZ-1
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Firmware will report flag with HTT_RX_IND_MPDU_STATUS_TKIP_MIC_ERR
if MIC error, the flag will be used in mac80211.
ieee80211_rx_h_michael_mic_verify will check the flag and start TKIP
countermeasures.
Now countermeasure tests pass both with WPA only and WPA2/WPA mixed
mode.
Tested with QCA6174 SDIO with firmware
WLAN.RMH.4.4.1-00007-QCARMSWP-1.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch will add the support to control the transmit power for traffic
to a station associated with the AP.
Underlying firmware will enforce that the maximum tx power will be based
on the regulatory requirements. If the user given transmit power is greater
than the allowed tx power in the given channel, then the firmware will use
the maximum tx power in the same channel.
Max and Min tx power values will depends on no of tx chain masks,
for QCA9984 allowed tx power range values from 6 to 23.
When 0 is sent to the firmware as tx power, it will revert to the default
tx power for the station.
Tested Hardware : QCA9984
Tested Firmware : 10.4-3.9.0.2-00046
Co-developed-by: Balaji Pothunoori <bpothuno@codeaurora.org>
Signed-off-by: Ashok Raj Nagarajan <arnagara@codeaurora.org>
Signed-off-by: Balaji Pothunoori <bpothuno@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Peer creation in firmware fails if last peer deletion is still
in progress.
The firmware sends a peer delete response event if it advertises
the service WMI_SERVICE_SYNC_DELETE_CMDS. This peer delete response
event is used to synchronize the peer deletion.
Add peer delete response event and wait for the event after
deleting every peer from host driver to synchronize with firmware.
Tested HW: WCN3990
Tested FW: WLAN.HL.2.0-01188-QCAHLSWMTPLZ-1
Signed-off-by: Dundi Raviteja <dundi@codeaurora.org>
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When we add an interface immediately after removing
the interface the vdev deletion in firmware might not
have been completed. We need to synchronize the vdev creation
with the firmware.
Wait for vdev delete response from firmware when we
remove an interface.
Tested HW: WCN3990
Tested FW: WLAN.HL.2.0-01188-QCAHLSWMTPLZ-1
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Observed PCIE device wake up failed after ~120 iterations of
soft-reboot test. The error message is
"ath10k_pci 0000:01:00.0: failed to wake up device : -110"
The call trace as below:
ath10k_pci_probe -> ath10k_pci_force_wake -> ath10k_pci_wake_wait ->
ath10k_pci_is_awake
Once trigger the device to wake up, we will continuously check the RTC
state until it returns RTC_STATE_V_ON or timeout.
But for QCA99x0 chips, we use wrong value for RTC_STATE_V_ON.
Occasionally, we get 0x7 on the fist read, we thought as a failure
case, but actually is the right value, also verified with the spec.
So fix the issue by changing RTC_STATE_V_ON from 0x5 to 0x7, passed
~2000 iterations.
Tested HW: QCA9984
Signed-off-by: Miaoqing Pan <miaoqing@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Currently, below fixed rate commands are broken,
iw wlanx set bitrates legacy-<2.4|5> ht-mcs-<2.4|5> vht-mcs-<2.4|5> \
<NSS:MCSx>
iw wlanx set bitrates legacy-<2.4|5> <legacy rate> ht-mcs-<2.4|5> \
vht-mcs-<2.4|5> <NSS:MCSx>
There are two methods to set fixed rate, both failed,
- Use vdev fixed rate command
This command only support one single rate, but it's broken due to
mac80211 change commit e8e4f5280d ("mac80211: reject/clear user
rate mask if not usable"), which requires user to specify at least
one legacy rate. So we can't use this command to set ht/vht single
rate any more.
- Use peer_assoc command
This command can update rx capability for multiple rates, it will
work fine for ht mcs rates, as each supported mcs can be advertised
in ht_mcs index mask. But this will not work with vht rates because,
as per the vht mcs capability advertisement, there are only two bits
to indicate the supported mcs. E.g. only support 0-7, 0-8, 0-9.
So introduced new WMI command: WMI_PEER_PARAM_FIXED_RATE. After peer
assoc, the peer fixed rate cmd will work for that specific peer.
Remaining peers will use auto rate. If both vdev fixed rate and peer
fixed rates are given, peer fixed rate will take effect to peers for
which this cmd is given. Remaining peers in that vdev, will use vdev
fixed rate.
Tested HW: QCA9984
Tested FW: 10.4-3.9.0.2-00035
Signed-off-by: Miaoqing Pan <miaoqing@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In function ath10k_sdio_mbox_rx_alloc() [sdio.c],
ath10k_sdio_mbox_alloc_rx_pkt() is called without handling the error cases.
This will make the driver think the allocation for skb is successful and
try to access the skb. If we enable failslab, system will easily crash with
NULL pointer dereferencing.
Call trace of CONFIG_FAILSLAB:
ath10k_sdio_irq_handler+0x570/0xa88 [ath10k_sdio]
process_sdio_pending_irqs+0x4c/0x174
sdio_run_irqs+0x3c/0x64
sdio_irq_work+0x1c/0x28
Fixes: d96db25d20 ("ath10k: add initial SDIO support")
Signed-off-by: Claire Chang <tientzu@chromium.org>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
For QCA988X target, pktlog gives details of the tx bitrate
which is used in the driver for station info.
Enabling pktlog by default will cause more interrupts
in target to host CE pipe, which can impact more CPU usage
for targets ex:WCN3990 and also not required for all other
platforms (eg: WCN3990), for getting tx bitrate.
Enable pktlog only for QCA988X based on hardware params.
Tested HW : WCN3990
Tested FW : WLAN.HL.3.1-00784-QCAHLSWMTPLZ-1
Fixes: e8123bb74c ("ath10k: add per peer tx stats support for 10.2.4")
Signed-off-by: Balaji Pothunoori <bpothuno@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Lockdep warns at lockdep_assert_held(&ar->data_lock) in
ath10k_htt_rx_pn_check_replay_hl(). Acquire ar->data_lock before calling
ath10k_htt_rx_pn_check_replay_hl() to fix it.
Call trace:
ath10k_htt_rx_pn_check_replay_hl+0x118/0x134 [ath10k_core]
ath10k_htt_rx_proc_rx_ind_hl+0xd8/0x250 [ath10k_core]
ath10k_htt_t2h_msg_handler+0x148/0xf30 [ath10k_core]
ath10k_htt_htc_t2h_msg_handler+0x24/0x40 [ath10k_core]
ath10k_sdio_irq_handler+0x374/0xaa4 [ath10k_sdio]
Fixes: 130c774957 ("ath10k: add PN replay protection for high latency devices")
Signed-off-by: Claire Chang <tientzu@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Firmware name for UTF mode of SDIO has changed from utf-2.bin to
utf-sdio-2.bin, so it need to change in ath10k, otherwise it will
fail for UTF mode.
After change the name in ath10k, it will success for UTF mode of
SDIO/USB.
Tested with QCA6174 SDIO with firmware
WLAN.RMH.4.4.1-00007-QCARMSWP-1.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The command to simulate firmware crash:
echo soft > /sys/kernel/debug/ieee80211/phy0/ath10k/simulate_fw_crash
It will send WMI_FORCE_FW_HANG_ASSERT to firmware, then it will trigger
CPU interrupt status register for SDIO chip, ath10k driver need to
configure it while enable SDIO interrupt, otherwise ath10k driver will
not get the assert error info.
After this change, it will success for simulate firmware crash.
Tested with QCA6174 SDIO with firmware
WLAN.RMH.4.4.1-00007-QCARMSWP-1.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Tested-by: Claire Chang <tientzu@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
ath10k_dbg() is called in ath10k_process_rx() with huge set of arguments
which is causing CPU overhead even when debug_mask is not set.
Good improvement was observed in the receive side performance when call
to ath10k_dbg() is avoided in the RX path.
Since currently all debug messages are sent via tracing infrastructure,
we cannot entirely avoid calling ath10k_dbg. Therefore, call to
ath10k_dbg() is made conditional based on tracing config in the driver.
Trasmit performance remains unchanged with this patch; below are some
experimental results with this patch and tracing disabled.
mesh mode:
w/o this patch with this patch
Traffic TP CPU Usage TP CPU usage
TCP 840Mbps 76.53% 960Mbps 78.14%
UDP 1030Mbps 74.58% 1132Mbps 74.31%
Infra mode:
w/o this patch with this patch
Traffic TP CPU Usage TP CPU usage
TCP Rx 1241Mbps 80.89% 1270Mbps 73.50%
UDP Rx 1433Mbps 81.77% 1472Mbps 72.80%
Tested platform : IPQ8064
hardware used : QCA9984
firmware ver : ver 10.4-3.5.3-00057
Signed-off-by: Kan Yan <kyan@chromium.org>
Signed-off-by: Venkateswara Naralasetty <vnaralas@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Without this op, it will not be possible to configure aggregation for
high latency devices.
Signed-off-by: Erik Stromdahl <erik.stromdahl@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This is done in order to make the *htt_h2t_aggr_cfg_msg* op align better
with the rest of the htt ops (whom all have inline wrappers).
It also adds support for the case when the op is missing (function
pointer is NULL).
As a result of this, the name of the 32 bit implementation in htt_tx.c
was changed and the function was made static.
Signed-off-by: Erik Stromdahl <erik.stromdahl@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Use 0600 as edcca file permission in mt76x02 debugfs
Fixes: 643749d4a8 ("mt76: mt76x02: disable ED/CCA by default")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Introduce a knob in mt7603 debugfs in order to enable/disable
energy detection based on CCA thresholds
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Run mt76x02_edcca_init atomically in mt76_edcca_set since it runs
concurrently with calibration work and mt76x2_set_channel.
Moreover perform phy calibration atomically
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This is a preliminary patch to run mt76x02_edcca_init atomically
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Remove mt76x02_edcca_init in mt76x2u_set_channel since it is already
run by mt76x2u_phy_channel_calibrate performing channel calibration
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Remove enable parameter from mt76x02_edcca_init routine signature since
it is always true
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Make mt7615_rx_poll_complete static since it is used just in pci.c
to initialize rx_poll_complete function pointer
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Run __mt76_mcu_send_msg instead of __mt7615_mcu_msg_send and remove
duplicated code.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Use common function wrapper in mt7615_mcu_exit since the code is shared
with m7603 driver
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Use __mt76_mcu_send_msg wrapper instead of mt7615_mcu_msg_send.
This is a preliminary patch for mt7615-mt7603 mcu code unification
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Use mt76 common signature for mt7615_mcu_msg_send. Move skb allocation
in mt7615_mcu_msg_send and remove duplicated code. Remove
__mt7615_mcu_set_wtbl and __mt7615_mcu_set_sta_rec since now are used
just to send mcu msgs. This is a preliminary patch for mt7615-mt7603 mcu
code unification
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Remove following struct no longer used:
- dev_info
- bss_info
- bss_info_tag_handler
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Remove function pointers in mt7615_mcu_set_bss_info and run function
directly. Moreover remove __mt7615_mcu_set_bss_info since it is run just
by mt7615_mcu_set_bss_info and remove duplicated istructions
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Unify mt7615_mcu_set_dev_info and __mt7615_mcu_set_dev_info since the
latter is run just by mt7615_mcu_set_dev_info
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Remove skb_ret parameter from mt7615_mcu_msg_send signature since it is
actually used just by mt7615_mcu_patch_sem_ctrl. This is a prelimanry
patch to use mt76 common mcu API
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Remove dest parameter from mt7615_mcu_msg_send/__mt7615_mcu_msg_send
routine signature since it can is always set to MCU_S2D_H2N
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Remove query parameter from mt7615_mcu_msg_send routine signature since
it can be obtained from cmd value
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Remove unused vif parameter in mt7615_mcu_del_wtbl signature
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Use proper mcu message size in mt7615_mcu_add_wtbl and do not
allocate a huge buffer. Moreover use stack memory instead of heap one
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Use proper mcu message size in mt7615_mcu_add_wtbl_bmc and do not
allocate a huge buffer. Moreover use stack memory instead of heap one
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Remove bss_info_convert_vif_type routine since it is run just in
mt7615_mcu_set_bss_info and the switch over vif->type is already there.
Simplify mt7615_mcu_set_bss_info routine
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Do not loop over cmd payload in __mt7615_mcu_set_sta_rec since it is
already done in before running __mt7615_mcu_set_sta_rec (e.g.
mt7615_mcu_set_sta_rec)
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Do not loop over cmd payload in __mt7615_mcu_set_wtbl since it is
already done in before running __mt7615_mcu_set_wtbl (e.g.
mt7615_mcu_set_wtbl_key)
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Fix sparse warning:
drivers/net/wireless/mediatek/mt76/mt7615/pci.c:37:13:
warning: symbol 'mt7615_irq_handler' was not declared. Should it be static?
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
We dereference "skb" when we assign:
req.pkt_len = cpu_to_le16(MT_TXD_SIZE + skb->len);
^^^^^^^^
So this patch just moves the dev_kfree_skb() down a bit to avoid the
use after free.
Fixes: 04b8e65922 ("mt76: add mac80211 driver for MT7615 PCIe-based chipsets")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The problem is that "mvif->omac_idx" is a u8 so it can't be negative
and the error handling won't work. The get_omac_idx() function returns
-1 on error.
Fixes: 04b8e65922 ("mt76: add mac80211 driver for MT7615 PCIe-based chipsets")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Felix Fietkau