We need to enable status changes for the fixed power supply for the USB
controller.
Fixes: 1d272894ec ("ARM: davinci: omapl138-hawk: add a fixed regulator for ohci-da8xx")
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
We need to enable status changes for the fixed power supply for the USB
controller.
Fixes: 274e4c3361 ("ARM: davinci: da830-evm: add a fixed regulator for ohci-da8xx")
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Display support for rk3228/rk3229 (up to hdmi output) and more love
for rk3288-veyron boards.
* tag 'v5.3-rockchip-dts32-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
ARM: dts: rockchip: add display nodes for rk322x
ARM: dts: rockchip: fix vop iommu-cells on rk322x
clk: rockchip: add clock id for hdmi_phy special clock on rk3228
clk: rockchip: add clock id for watchdog pclk on rk3328
Revert "ARM: dts: rockchip: set PWM delay backlight settings for Minnie"
ARM: dts: rockchip: Configure BT_DEV_WAKE in on rk3288-veyron
ARM: dts: rockchip: Configure BT_HOST_WAKE as wake-up signal on veyron
Signed-off-by: Olof Johansson <olof@lixom.net>
mvebu fixes for 5.2 (part 2)
Use the armada-38x-uart compatible strings for Armada XP 98dx3236 SoCs
in order to not loose character anymore.
* tag 'mvebu-fixes-5.2-2' of git://git.infradead.org/linux-mvebu:
ARM: dts: armada-xp-98dx3236: Switch to armada-38x-uart serial node
Signed-off-by: Olof Johansson <olof@lixom.net>
The datasheet of S2MPS11 PMIC is slightly non-consistent in buck[78]
voltage regulators values.
1. The voltage tables for configuring their registers mention range of
voltages: 0.750 V to 3.55 V,
2. The constrains in electrical specifications say output voltage range
to be different (buck7: 1.2 V to 1.5 V, buck8: 1.8 V to 2.1 V).
Adjust the ranges to match the electrical specifications to stay on the
safe side. Anyway these regulators stay at default value so this should
not have effect.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
The datasheet of S2MPS11 PMIC is slightly non-consistent in buck[78]
voltage regulators values.
1. The voltage tables for configuring their registers mention range of
voltages: 0.750 V to 3.55 V,
2. The constrains in electrical specifications say output voltage range
to be different (buck7: 1.2 V to 1.5 V, buck8: 1.8 V to 2.1 V).
Adjust the ranges to match the electrical specifications to stay on the
safe side. Also change the name of regulators to match reality. Anyway
these regulators stay at default value so this should not have effect.
Reported-by: Anand Moon <linux.amoon@gmail.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Mali400 GPU hardware module is a standard hardware module integrated to
Exynos3210/4210/4412 SoCs, so it should reside under the "/soc" node.
The only SoC components which are placed in the DT root, are those, which
are a part of CPUs: like ARM architected timers and ARM performance
measurement units.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
The PMU module of Mali400 GPU is optional and it looks that it is not
present on Exynos4210, because any access to its registers causes external
abort. This patch removes "pmu" interrupt for Exynos4210 SoCs, so the
driver will skip the PMU module. This fixes following fault during kernel
boot:
Unhandled fault: imprecise external abort (0x1406) at 0x00000000
(lima_pmu_init) from [<c059e6f8>] (lima_device_init+0x244/0x5a0)
(lima_device_init) from [<c059e40c>] (lima_pdev_probe+0x7c/0xd8)
(lima_pdev_probe) from [<c05afcb8>] (platform_drv_probe+0x48/0x9c)
(platform_drv_probe) from [<c05ad594>] (really_probe+0x1c4/0x400)
(really_probe) from [<c05ad988>] (driver_probe_device+0x78/0x1b8)
(driver_probe_device) from [<c05add30>] (device_driver_attach+0x58/0x60)
(device_driver_attach) from [<c05ade34>] (__driver_attach+0xfc/0x160)
(__driver_attach) from [<c05ab650>] (bus_for_each_dev+0x68/0xb4)
(bus_for_each_dev) from [<c05ac734>] (bus_add_driver+0x104/0x20c)
(bus_add_driver) from [<c05aece0>] (driver_register+0x78/0x10c)
(driver_register) from [<c0103214>] (do_one_initcall+0x8c/0x430)
(do_one_initcall) from [<c0f01328>] (kernel_init_freeable+0x3c8/0x4d0)
(kernel_init_freeable) from [<c0ac3aa0>] (kernel_init+0x8/0x10c)
(kernel_init) from [<c01010b4>] (ret_from_fork+0x14/0x20)
The PMU module seems to work fine on Exynos4412 SoCs, so the patch also
moves the interrupt definitions to exynos4210.dtsi and exynos4412.dtsi
respectively, to keep only the common part in exynos4.dtsi.
Fixes: 13efd80aca ("ARM: dts: exynos: Add GPU/Mali 400 node to Exynos4")
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Felipe writes:
usb: changes for v5.3 merge window
The biggest part here is a set of patches removing unnecesary variables
from several drivers.
Meson-g12a's dwc3 glue implemented IRQ-based OTG/DRD role swap.
Qcom's dwc3 glue added support for ACPI, mainly for the AArch64-based
SoCs.
DWC3 also got support for Intel Elkhart Lake platforms.
* tag 'usb-for-v5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb: (30 commits)
usb: dwc3: remove unused @lock member of dwc3_ep struct
usb: dwc3: pci: Add Support for Intel Elkhart Lake Devices
usb: Replace snprintf with scnprintf in gether_get_ifname
usb: gadget: ether: Fix race between gether_disconnect and rx_submit
usb: gadget: storage: Remove warning message
usb: dwc3: gadget: Add support for disabling U1 and U2 entries
usb: gadget: send usb_gadget as an argument in get_config_params
doc: dt: bindings: usb: dwc3: Update entries for disabling U1 and U2
usb: dwc3: qcom: Use of_clk_get_parent_count()
usb: dwc3: Fix core validation in probe, move after clocks are enabled
usb: dwc3: qcom: Improve error handling
usb: dwc3: qcom: Start USB in 'host mode' on the SDM845
usb: dwc3: qcom: Add support for booting with ACPI
soc: qcom: geni: Add support for ACPI
Revert "usb: dwc2: host: Setting qtd to NULL after freeing it"
usb: gadget: net2272: remove redundant assignments to pointer 's'
usb: gadget: Zero ffs_io_data
USB: omap_udc: Remove unneeded variable
fotg210-udc: Remove unneeded variable
usb: gadget: at91_udc: Remove unneeded variable
...
Qualcomm Device Tree Changes for v5.3
* Add vibrator motor for MSM8974 based Fairphone 2
* tag 'qcom-dts-for-5.3-2' of git://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux:
ARM: dts: msm8974-FP2: Add vibration motor
Signed-off-by: Olof Johansson <olof@lixom.net>
The new route handling in ip_mc_finish_output() from 'net' overlapped
with the new support for returning congestion notifications from BPF
programs.
In order to handle this I had to take the dev_loopback_xmit() calls
out of the switch statement.
The aquantia driver conflicts were simple overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull ARM SoC fixes from Olof Johansson:
"A smaller batch of fixes, nothing that stands out as risky or scary.
Mostly DTS tweaks for a few issues:
- GPU fixlets for Meson
- CPU idle fix for LS1028A
- PWM interrupt fixes for i.MX6UL
Also, enable a driver (FSL_EDMA) on arm64 defconfig, and a warning and
two MAINTAINER tweaks"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc:
ARM: dts: imx6ul: fix PWM[1-4] interrupts
ARM: omap2: remove incorrect __init annotation
ARM: dts: gemini Fix up DNS-313 compatible string
ARM: dts: Blank D-Link DIR-685 console
arm64: defconfig: Enable FSL_EDMA driver
arm64: dts: ls1028a: Fix CPU idle fail.
MAINTAINERS: BCM53573: Add internal Broadcom mailing list
MAINTAINERS: BCM2835: Add internal Broadcom mailing list
ARM: dts: meson8b: fix the operating voltage of the Mali GPU
ARM: dts: meson8b: drop undocumented property from the Mali GPU node
ARM: dts: meson8: fix GPU interrupts and drop an undocumented property
If UHS speed modes are enabled, a compatible SD card switches down to
1.8V during enumeration. If after this a software reboot/crash takes
place and on-chip ROM tries to enumerate the SD card, the difference in
IO voltages (host @ 3.3V and card @ 1.8V) may end up damaging the card.
The fix for this is to have support for power cycling the card in
hardware (with a PORz/soft-reset line causing a power cycle of the
card). Because the beaglebone X15 (rev A,B and C), am57xx-idks and
am57xx-evms don't have this capability, disable voltage switching for
these boards.
The major effect of this is that the maximum supported speed
mode is now high speed(50 MHz) down from SDR104(200 MHz).
commit 88a748419b ("ARM: dts: am57xx-idk: Remove support for voltage
switching for SD card") did this only for idk boards. Do it for all
affected boards.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add display_subsystem, hdmi_phy, vop, and hdmi device nodes plus
a few hdmi pinctrl entries to allow for HDMI output.
Signed-off-by: Justin Swartz <justin.swartz@risingedge.co.za>
[added assigned-clock settings for hdmiphy output]
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Samsung mach/soc changes for v5.3
Only cleanups and minor fixes.
* tag 'samsung-soc-5.3' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
ARM: exynos: Cleanup cppcheck shifting warning
ARM: exynos: Only build MCPM support if used
ARM: exynos: Make ARCH_EXYNOS3 a default option
Signed-off-by: Olof Johansson <olof@lixom.net>
Samsung defconfig changes for v5.3
1. Trim several configs with savedefconfig.
2. Enable Lima and Panfrost drivers for Mali GPU.
* tag 'samsung-defconfig-5.3' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
ARM: exynos_defconfig: Enable Panfrost and Lima drivers
ARM: multi_v7_defconfig: Enable Panfrost and Lima drivers
ARM: defconfig: samsung: Cleanup with savedefconfig
ARM: exynos_defconfig: Trim and reorganize with savedefconfig
Signed-off-by: Olof Johansson <olof@lixom.net>
Samsung DTS ARM changes for v5.3, second round
1. Add camera flash to Galaxy S3 boards,
2. Fix PMU affinity interrupt warning on Exynos4,
3. Improve regulator configuration on Odroid XU3/XU4/HC1 family and
Arndale Octa by disabling unneeded regulators and adding suspend
configuration. The suspend configuration brings significant reduce of
energy usage in Suspend to RAM (e.g. 120 -> ~7 mA on Odroid HC1).
4. Add Mali nodes to Exynos3 and Exynos4.
* tag 'samsung-dt-5.3-2' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
ARM: dts: exynos: Add GPU/Mali 400 node to Exynos4
ARM: dts: exynos: Add GPU/Mali 400 node to Exynos3250
dt-bindings: gpu: mali: Add Samsung compatibles for Midgard and Utgard
ARM: dts: exynos: Use proper regulator for eMMC memory on Arndale Octa
ARM: dts: exynos: Add regulator suspend configuration to Odroid XU3/XU4/HC1 family
ARM: dts: exynos: Add regulator suspend configuration to Arndale Octa board
ARM: dts: exynos: Disable unused buck10 regulator on Odroid HC1 board
ARM: dts: exynos: Fix language typo and indentation
ARM: dts: exynos: Add PMU interrupt affinity to Exynos4 boards
ARM: dts: exynos: Add flash support to Galaxy S3 boards
Signed-off-by: Olof Johansson <olof@lixom.net>
UniPhier ARM SoC DT updates for v5.3
- Migrate to the new binding for the Denali NAND controller
* tag 'uniphier-dt-v5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-uniphier:
ARM: dts: uniphier: update to new Denali NAND binding
Signed-off-by: Olof Johansson <olof@lixom.net>
A recent change mistakenly added a second copy of these two options,
which kbuild warns about:
arch/arm/configs/multi_v5_defconfig:257:warning: override: reassigning
to symbol ASPEED_LPC_CTRL
arch/arm/configs/multi_v5_defconfig:258:warning: override: reassigning
to symbol ASPEED_LPC_SNOOP
Fixes: 2d8bf3404b ("ARM: configs: multi_v5: Add more ASPEED devices")
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Olof Johansson <olof@lixom.net>
This reverts commit 288ceb85b5.
The commit assumes that the minnie panel is a AUO B101EAN01.1 (LVDS
interface), however it is a AUO B101EAN01.8 (eDP interface). The eDP
panel doesn't need the 200 ms delay.
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
This is the other half of the hacky solution from commit f497ab6b4b
("ARM: dts: rockchip: Configure BT_HOST_WAKE as wake-up signal on
veyron"). Specifically the LPM driver that the Broadcom Bluetooth
expects to have (but is missing in mainline) has two halves of the
equation: BT_HOST_WAKE and BT_DEV_WAKE. The BT_HOST_WAKE (which was
handled in the previous commit) is the one that lets the Bluetooth
wake the system up. The BT_DEV_WAKE (this patch) tells the Bluetooth
that it's OK to go into a low power mode. That means we were burning
a bit of extra power in S3 without this patch. Measurements are a bit
noisy, but it appears to be a few mA worth of difference.
NOTE: Though these pins don't do much on systems with Marvell
Bluetooth, downstream kernels set it on all veyron boards so we'll do
the same.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The SNVS LPGPR hardware is present on several i.MX SoCs.
Select its driver by default.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Enable the OV2680 camera driver as it is used on the imx7s-warp board.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Enable CONFIG_THERMAL_STATISTICS to extend the sysfs interface
for thermal cooling devices and expose some useful statistics.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Fix warning from cppcheck tool:
"Shifting signed 32-bit value by 31 bits is undefined behaviour errors"
Signed-off-by: Phong Tran <tranmanphong@gmail.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Different mechanisms are used to test and set elf_hwcaps between ARM
and ARM64, this results in the use of ifdeferry in this file when
setting/testing for the EVTSTRM hwcap.
Let's improve readability by extracting this to an arch helper.
Signed-off-by: Andrew Murray <andrew.murray@arm.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
With commit d8e8fd0ebf ("mtd: rawnand: denali: decouple controller
and NAND chips"), the Denali NAND controller driver migrated to the
new controller/chip representation.
Update DT for it.
In the new binding, the number of connected chips are described in
DT instead of run-time probed.
I added just one chip to the reference boards, where we do not know
if the on-board NAND device is a single chip or multiple chips.
If we added too many chips into DT, it would end up with the timeout
error in nand_scan_ident().
I changed all the pinctrl properties to use the single CS.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
i.MX SoC changes for 5.3:
- Switch imx7d to imx-cpufreq-dt for speed-grading, as imx-cpufreq-dt
driver can handle speed grading bits on imx7d just like on imx8mq.
- Improve imx6 cpuidle driver to use raw_spinlock_t. The change makes
no difference for !RT build, but is required by RT kernel.
* tag 'imx-soc-5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: imx: Switch imx7d to imx-cpufreq-dt for speed-grading
ARM: imx6: cpuidle: Use raw_spinlock_t
Signed-off-by: Olof Johansson <olof@lixom.net>
This is the pxa changes for 5.3 cycle :
- a simple cleanup for lubbock
* tag 'pxa-for-5.3-2' of https://github.com/rjarzmik/linux:
ARM: pxa/lubbock: remove lubbock_set_misc_wr() from global view
Signed-off-by: Olof Johansson <olof@lixom.net>
AT91 SoC for 5.3
- fix a pm.c warning with W=1
* tag 'at91-5.3-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/at91/linux:
arm: add missing include platform-data/atmel.h
Signed-off-by: Olof Johansson <olof@lixom.net>
Renesas ARM Based SoC Updates for v5.3
* Auto-enable RZ/A1 IRQC on RZ/A1H and RZ/A2M
* Don't init CNTVOFF/counter if PSCI is available
* tag 'renesas-arm-soc-for-v5.3' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
soc: renesas: Enable RZ/A1 IRQC on RZ/A1H and RZ/A2M
ARM: mach-shmobile: Don't init CNTVOFF/counter if PSCI is available
Signed-off-by: Olof Johansson <olof@lixom.net>
This pull request has a patch to switch DA850 EVM GPIO LED support to use
GPIO lookup table
* tag 'davinci-for-v5.3/soc' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci:
ARM: davinci: Use GPIO lookup table for DA850 LEDs
Signed-off-by: Olof Johansson <olof@lixom.net>
ASPEED device tree updates for 5.3
Add new drivers to the ASPEED G4 and G5 defconfigs, and to the armv5
multi defconfig.
* tag 'aspeed-5.3-defconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/joel/aspeed:
ARM: configs: multi_v5: Add more ASPEED devices
ARM: configs: aspeed: Add new drivers
Signed-off-by: Olof Johansson <olof@lixom.net>
Renesas ARM Based SoC Defconfig Updates for v5.3
* Remove GENERIC_PHY from shmobile_defconfig as it is now selected
* tag 'renesas-arm-defconfig-for-v5.3' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: Remove GENERIC_PHY from shmobile_defconfig
Signed-off-by: Olof Johansson <olof@lixom.net>
Qualcomm ARM Based defconfig Updates for v5.3
* Add support for USB networking
* Add support for display related options
* tag 'qcom-defconfig-for-5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux:
ARM: qcom_defconfig: add support for USB networking
ARM: qcom_defconfig: add display-related options
Signed-off-by: Olof Johansson <olof@lixom.net>
i.MX arm32 DT changes for 5.3:
- New board support: iMX6-based Kontron SMARC-sAMX6i, i.MX7D based
Meerkat96 board, and NXP LS1021A-TSN board.
- A series from Andrey Smirnov to update vf610-zii-dev and
imx7d-zii-rpu2 board, fixing UART2 pin assignment and stdout-path,
adding QSPI device, and dropping unused pinmux.
- Update imx6sl and imx6qdl device tree to assign corresponding clocks
instead of dummy clock.
- Update i.MX6/7 boards from NXP to assign corresponding power supply
for LDOs.
- Update i.MX6/7 device trees to enable SNVS poweroff key support
according to board design.
- Update coresight DT binding for i.MX7 according to consolidations
for CoreSight replicator and funnel.
- A series from Marek Vasut to update M53Menlo board on various devices
like UART, USB, ethernet PHY, GPIOs etc.
- Enable USBOTG support for imx7ulp and evk board.
- A series from Peter Robinson to update imx6sx-udoo board, switching
to SPDX License Identifier, enabling I2C devices and bluetooth
support.
- Add video capture support for i.MX53 and imx53-smd board.
- Add PXP device for i.MX6UL.
- Other random small updates on various boards.
* tag 'imx-dt-5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: (46 commits)
ARM: dts: imx7ulp-evk: enable USBOTG1 support
ARM: dts: imx7ulp: add imx7ulp USBOTG1 support
ARM: dts: imx6qdl-kontron-samx6i: add Kontron SMARC SoM Support
ARM: dts: imx6qdl-kontron-samx6i: Add iMX6-based Kontron SMARC-sAMX6i module
ARM: dts: imx7d-zii-rpu2: Drop unused pinmux entries
ARM: dts: imx7d-zii-rpu2: Fix incorrrect 'stdout-path'
ARM: dts: Add support for 96Boards Meerkat96 board
ARM: dts: imx6ul: Add PXP node
ARM: dts: imx6sll: Enable SNVS poweroff according to board design
ARM: dts: imx7s: Enable SNVS power key according to board design
ARM: dts: imx6sll: Enable SNVS power key according to board design
ARM: dts: imx6ul: Enable SNVS power key according to board design
ARM: dts: imx6sx: Enable SNVS power key according to board design
ARM: dts: imx6qdl: Enable SNVS power key according to board design
ARM: dts: imx53: Bind CPLD on M53Menlo
ARM: dts: Introduce the NXP LS1021A-TSN board
ARM: dts: imx6ull-colibri: enable UHS-I for USDHC1
ARM: dts: imx7d: Update cpufreq OPP table
ARM: dts: imx6sx-udoo-neo: add bluetooth config to uart3
ARM: dts: imx6sx-udoo-neo: enable i2c-2 and i2c-4 for onboard sensors
...
Signed-off-by: Olof Johansson <olof@lixom.net>
This is the pxa devicetree changes for 5.3 cycle :
- devicetree pinmux support for bias on pxa3xx
- devicetree pinmux bias usage for raumfeld
* tag 'pxa-dt-5.3' of https://github.com/rjarzmik/linux:
ARM: dts: pxa300-raumfeld-speaker-one: add channel output mapping for STA320
ARM: pxa: raumfeld-common: fix comments in gpio_keys pinctrl node
ARM: pxa: raumfeld-controller: add pinctrl for charger pins
ARM: pxa: raumfeld-controller: fix 'dock detect' GPIO key
ARM: pxa3xx: dts: Add defines for pinctrl-single,bias-pull{up,down}
Signed-off-by: Olof Johansson <olof@lixom.net>
AT91 DT for 5.3
- switch to new sckc bindings
- convert soc bindings to json-schema
* tag 'at91-5.3-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/at91/linux:
dt-bindings: arm: Convert Atmel board/soc bindings to json-schema
ARM: dts: at91: sama5d3: switch to new sckc bindings
ARM: dts: at91: at91sam9rl: switch to new sckc bindings
ARM: dts: at91: at91sam9g45: switch to new sckc bindings
ARM: dts: at91: at91sam9x5: switch to new sckc bindings
ARM: dts: at91sam9261ek: remove unused chosen nodes
Signed-off-by: Olof Johansson <olof@lixom.net>
STM32 DT updates for v5.3, round 1
Highlights:
----------
MPU part:
-Add stm32mp157a-avenger board support:
This board embeds a STM32MP157a SOC with AC package (TFBGA361, 148 ios)
, 1024MB of DDR3 and STPMIC1A pmic . Several connections are available on this boards:
2x Type A (USB 2.0) Host and 1x Micro B (USB 2.0) OTG, ethernet
10/100/1000, WiFi 5 GHz & 2.4GHz, ...
-Add STMFX support en stm32mp157c-ev1 and enable joystick connected on
it.
-Add I2S and SAI support on stm32mp157c.
-Add and enable support of Vivante GPU on stm32mp157 ED1 and DK1 boards
(EV1 and DK2 inherit of it).
-Add camera support:
-Add DCMI support on stm32mp157c SOC
-Enabled OV5640 camera support on stm32mp157c-ev1 board
-Enable hdmi bridge sii9022 & display controller on stm32mp157c-dk1
board.
MCU part:
-Add STMFX support en stm32746g-eval and enable connections on it:
leds and joystick
* tag 'stm32-dt-for-v5.3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/atorgue/stm32: (27 commits)
ARM: dts: stm32: replace rgmii mode with rgmii-id on stm32mp15 boards
ARM: dts: stm32: Add Avenger96 devicetree support based on STM32MP157A
dt-bindings: arm: stm32: Document Avenger96 devicetree binding
dt-bindings: arm: stm32: Convert STM32 SoC bindings to DT schema
ARM: dts: stm32: Add missing pinctrl definitions for STM32MP157
ARM: dts: stm32: add sai id registers to stm32mp157c
ARM: dts: stm32: add power supply of rm68200 on stm32mp157c-ev1
ARM: dts: stm32: enable display on stm32mp157c-dk1 board
ARM: dts: stm32: Add I2C 1 config for stm32mp157a-dk1
ARM: dts: stm32: enable OV5640 camera on stm32mp157c-ev1 board
ARM: dts: stm32: add DCMI pins to stm32mp157c
ARM: dts: stm32: add DCMI camera interface support on stm32mp157c
ARM: dts: stm32: enable Vivante GPU support on stm32mp157a-dk1 board
ARM: dts: stm32: enable Vivante GPU support on stm32mp157c-ed1 board
ARM: dts: stm32: Add Vivante GPU support on STM32MP157c
ARM: dts: stm32: add i2s pins muxing on stm32mp157
ARM: dts: stm32: add i2s support on stm32mp157c
ARM: dts: stm32: add sai pins muxing on stm32mp157
ARM: dts: stm32: add sai support on stm32mp157c
ARM: dts: stm32: add jedec compatible for nor flash on stm32mp157c-ev1
...
Signed-off-by: Olof Johansson <olof@lixom.net>
mvebu dt for 5.3 (part 1)
Add LCD support on Netgear RN104
* tag 'mvebu-dt-5.3-1' of git://git.infradead.org/linux-mvebu:
ARM: dts: armada: netgear-rn104: Add LCD to RN104 dts.
Signed-off-by: Olof Johansson <olof@lixom.net>
This time we only have a single patch for our command branch between
arm and arm64, a fix for the array syntax raised by our DT schemas.
* tag 'sunxi-h3-h5-for-5.3-201906210812' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
ARM: dts: sunxi: h3/h5: Fix GPIO regulator state array
Signed-off-by: Olof Johansson <olof@lixom.net>
Bartosz Golaszewski