The mp2629 provides switching-mode battery charge management for
single-cell Li-ion or Li-polymer battery. Driver supports the
access/control input source and battery charging parameters.
Signed-off-by: Saravanan Sekar <sravanhome@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Edge interrupts from the charger may be lost or stuck in fault mode
since probe(). Check if something changed everytime userspace wants
some data.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Datasheet describes two modes for reading ADC measurements:
1. continuous, 1 Hz - enabled and started by CONV_RATE bit
2. one-shot - triggered by CONV_START bit
In continuous mode, CONV_START is read-only and signifies an ongoing
conversion.
Change the code to follow the datasheet and really disable continuous
mode for power saving.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Charge Current is more apropriately reflected by CURRENT_NOW property
(measured current) than CONSTANT_CURRENT_VOLTAGE (configured CC-phase
current limit). Fix the reference and make the sign reflect direction
of the current.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The framework is unhappy about them, because it uses the names in sysfs
attributes:
power_supply olpc-ac: hwmon: 'olpc-ac' is not a valid name attribute, please fix
power_supply olpc-battery: hwmon: 'olpc-battery' is not a valid name attribute, please fix
See also commit 648cd48c9e ("hwmon: Do not accept invalid name
attributes") and commit 74d3b64197 ("hwmon: Relax name attribute
validation for new APIs").
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
This delay-fix is picked up from downstream driver,
we measured that 25 - 35 ms delay ensure that we get required data.
Tested on SMB347 on Nexus 7 2012. Otherwise IRQSTAT_E fails to provide
correct information.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: David Heidelberg <david@ixit.cz>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Fix failure when USB cable is connected:
smb347 2-006a: reading IRQSTAT_D failed
Fixes: 1502cfe19b ("smb347-charger: Fix battery status reporting logic for charger faults")
Tested-by: David Heidelberg <david@ixit.cz>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: David Heidelberg <david@ixit.cz>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The ROHM BD99954 is a Battery Management LSI for 1-4 cell Lithium-Ion
secondary battery intended to be used in space-constraint equipment such
as Low profile Notebook PC, Tablets and other applications. BD99954
provides a Dual-source Battery Charger, two port BC1.2 detection and a
Battery Monitor.
Support ROHM BD99954 Charger IC.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
lib: Add linear ranges helper library and start using it
Series extracts a "linear ranges" helper out of the regulator
framework. Linear ranges helper is intended to help converting
real-world values to register values when conversion is linear. I
suspect this is useful also for power subsystem and possibly for clk.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
In the probe function, in case of error, resources allocated in
'lp8788_setup_adc_channel()' must be released.
This can be achieved easily by using the devm_ variant of
'iio_channel_get()'.
This has the extra benefit to simplify the remove function and to axe the
'lp8788_release_adc_channel()' function which is now useless.
Fixes: 98a2766493 ("power_supply: Add new lp8788 charger driver")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Fix the following warning:
drivers/power/supply/cw2015_battery.c:96:5: warning:
'cw_update_profile' was not declared. Should it be static?
drivers/power/supply/cw2015_battery.c:712:1: warning:
'cw_bat_pm_ops' was not declared. Should it be static?
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: ChenTao <chentao107@huawei.com>
Acked-by: Tobias Schramm <t.schramm@manjaro.org>
Tested-by: Tobias Schramm <t.schramm@manjaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
We introduced some new locking here, but need to update the error
paths so they unlock before returning.
Fixes: 72d9cd9cdc ("power: bq25890: protect view of the chip's state")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Add POWER_SUPPLY_TYPE to the uevent env for power supply. Type is a
property of all power supplies and there is a sysfs entry for it but it
is not included in the properties array of the power supply so
explicitly add it to the udev env.
Signed-off-by: Mathew King <mathewk@chromium.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Reduce the number of touch points to add a new enum property to the
power_supply class by mapping the array of text values to the device
attribute descriptor. A new enum property can now added by creating an
array with the text values named POWER_SUPPLY_${PROPNAME}_TEXT and
adding POWER_SUPPLY_ENUM_ATTR(${PROPNAME}) to the power_supply_attrs
array.
Signed-off-by: Mathew King <mathewk@chromium.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Use designated initializers for the sysfs power supply text values. This
will help ensure that the text values are kept in sync with the enum
values from power_supply.h.
Signed-off-by: Mathew King <mathewk@chromium.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Make the device attribute list used to create sysfs attributes more
robust by decoupling the list order from order of the enum defined in
power_supply.h. This is done by using a designated initializer in the
POWER_SUPPLY_ATTR macro.
Signed-off-by: Mathew King <mathewk@chromium.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Extend bq->lock over whole updating of the chip's state. Might get
useful later for switching ADC modes correctly.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
regmap initialization will check I2C adapter functionality.
Remove redundant check in the driver.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Driver rejects unknown chips early in the probe(), so when
bq25890_power_supply_get_property() is made reachable, bq->chip_version
will already be set to correct value - there is no need to check
it again.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
This patch adds a driver for the CellWise cw2015 fuel gauge.
The CellWise cw2015 is a shuntless, single-cell Li-Ion fuel gauge used
in the pine64 Pinebook Pro laptop and some Raspberry Pi UPS HATs.
Signed-off-by: Tobias Schramm <t.schramm@manjaro.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
In function power_supply_add_hwmon_sysfs(), psyhw->props is
allocated by bitmap_zalloc(). But this pointer is not deallocated
when devm_add_action fail, which lead to a memory leak bug. To fix
this, we replace devm_add_action with devm_add_action_or_reset.
Cc: stable@kernel.org
Fixes: e67d4dfc9f ("power: supply: Add HWMON compatibility layer")
Signed-off-by: Qiushi Wu <wu000273@umn.edu>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Rework power_supply_hwmon_read_string() to check it's parameters.
This allows to extend it later with labels for other types of
measurements.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Initialize num_properties with length of the copied array instead
of relying on previously memcpy'd value. This makes it clear how
the array and the counter are related.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Currently HWMON emulation shows all labels (temp and ambient temp)
regardless if power supply supports reading the values. Check that at
least one property is enabled for each label.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Reduce power_supply_show_usb_type() parameter count by folding
power_supply_desc dereference into the function. This makes following
patch making usb_types const easier.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The max170{42,47,50,55} family of fuel gauges all provide time-to-empty
estimation. As such, let's export this as a property.
Signed-off-by: Geordan Neukum <gneukum1@gmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The battery full capacity can be affected by the temperature or the
servicing time or other factors, so some platforms will track the
real battery full capacity in charger manager service. Thus we should
allow to change the battery full capacity by setting the
'POWER_SUPPLY_PROP_ENERGY_FULL_DESIGN' property as writeable.
Signed-off-by: Yuanjiang Yu <yuanjiang.yu@unisoc.com>
Signed-off-by: Baolin Wang <baolin.wang7@gmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Get rid of linux/vermagic.h includes, so that MODULE_ARCH_VERMAGIC from
the arch header arch/x86/include/asm/module.h won't be redefined.
In file included from ./include/linux/module.h:30,
from drivers/net/ethernet/3com/3c515.c:56:
./arch/x86/include/asm/module.h:73: warning: "MODULE_ARCH_VERMAGIC"
redefined
73 | # define MODULE_ARCH_VERMAGIC MODULE_PROC_FAMILY
|
In file included from drivers/net/ethernet/3com/3c515.c:25:
./include/linux/vermagic.h:28: note: this is the location of the
previous definition
28 | #define MODULE_ARCH_VERMAGIC ""
|
Fixes: 6bba2e89a8 ("net/3com: Delete driver and module versions from 3com drivers")
Co-developed-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Borislav Petkov <bp@suse.de>
Acked-by: Shannon Nelson <snelson@pensando.io> # ionic
Acked-by: Sebastian Reichel <sre@kernel.org> # power
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the pm860x_battery_probe(), when get irq failed, the function
platform_get_irq() logs an dev_err message, so remove redundant
message here.
Signed-off-by: Tang Bin <tangbin@cmss.chinamobile.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The Meegopad T02 is a PC in stick format and doesn't have a battery,
it is reported with a random and constant battery charge but as
discharging to userspace.
Add it to the blacklist to avoid the bogus battery status reporting.
Signed-off-by: Rafael Gandolfi <rafirafi.at@gmail.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Fix the following gcc warning:
drivers/power/supply/max14656_charger_detector.c:142:6: warning:
variable ‘ret’ set but not used [-Wunused-but-set-variable]
int ret = 0;
^~~
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Saravanan Sekar