Add support for using the SCIx clock pin "(H)SCK" as an external clock
input on (H)SCI(F), providing the sampling clock.
Note that this feature is not yet supported on the select SCIFA variants
that also have it (e.g. sh7723, sh7724, and r8a7740).
On (H)SCIF variants with an External Baud Rate Generator (BRG), the
BRG Clock Select Register must be configured for the external clock.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Refactor the clock and baud rate parameter code to ease adding support
for multiple sampling clock sources.
sci_scbrr_calc() now returns the bit rate error, so it can be compared
to the bit rate error using other sampling clock sources.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The "renesas,scif" compatible value is currently used for the SCIF
variant in all Renesas SoCs of the R-Car family. However, the variant
used in the R-Car family is not the common "SH-4(A)" variant, but a
derivative with added "Baud Rate Generator for External Clock" (BRG),
which is also present in sh7734.
Use the family-specific SCIF compatible values for R-Car Gen1, Gen2, and
Gen3 SoCs to differentiate. The "renesas,scif" compatible value can
still be used as a common denominator for SCIF variants with the
"SH-4(A)" register layout (i.e. ignoring the "Serial Extension Mode
Register" (SCEMR) and the new BRG-specific registers).
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The "renesas,scif" compatible value is currently used for the SCIF
variant in all Renesas SoCs of the R-Car and RZ families. However, the
variant used in the RZ family is not the common "SH-4(A)" variant, but
the "SH-2(A) with FIFO data count register" variant, as it has the
"Serial Extension Mode Register" (SCEMR), just like on sh7203, sh7263,
sh7264, and sh7269.
Use the (already documented) SoC-specific "renesas,scif-r7s72100"
compatible value to differentiate. The "renesas,scif" compatible value
can still be used as a common denominator for SCIF variants with the
"SH-4(A)" register layout (i.e. ignoring the SCEMR register).
Note that currently both variants are treated the same, but this may
change if support for the SCEMR register is ever added.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Store the encoded port and register types directly in of_device_id.data,
instead of using a pointer to a structure.
This saves memory and simplifies the source code, especially when adding
more compatible entries later.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add register definitions for the Baud Rate Generator for External Clock
(BRG), as found in some SCIF and in HSCIF, including a new regtype for
the "SH-4(A)"-derived SCIF variant with BRG.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For low bit rates, the for-loop that reduces the divider returned by
sci_scbrr_calc() and picks the clock select value may terminate without
finding suitable values, leading to out-of-range divider and clock
select values.
sci_baud_calc_hscif() doesn't suffer from this problem, as it correctly
uses clamp().
Since there are only two relevant differences between HSCIF and other
variants w.r.t. bit rate configuration (fixed vs. variable sample rate,
and an additional factor of two), sci_scbrr_calc() and
sci_baud_calc_hscif() can be merged, fixing the issue with out-of-range
values.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When assuming D = 0.5 and F = 0, maximizing the receive margin M is
equivalent to maximizing the sample rate N.
Hence there's no need to calculate the receive margin, as we can obtain
the same result by iterating over all possible sample rates in reverse
order, and skipping parameter sets that don't provide a lower bit rate
error.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The algorithm to find the best parameters for the requested bit rate
calculates the relative bit rate error, using "(br * scrate) / 1000".
For small "br * scrate", this has two problems:
- The quotient may be zero, leading to a division by zero error,
- This may introduce a large rounding error.
Switch from relative to absolute bit rate error calculation to fix this.
The default baud rate generator values can be removed, as there will
always be one set of values that gives the smallest absolute error.
Print the best set of values when debugging.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If bps >= 1048576, the multiplication of the predivider and "bps" will
overflow, and both br and err will contain bogus values.
Skip the current and all higher clock select predividers when overflow
is detected. Simplify the calculations using intermediates while we're
at it.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move the -1 offset of br to the assignment to *brr, so br cannot become
negative anymore, and update the clamp() call. Now all unsigned values
in sci_baud_calc_hscif() can become unsigned.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Blindly writing the default configuration value into the SCSCR register
may change the clock selection bits, breaking the serial console if the
current driver settings differ from the default settings.
Keep the current clock selection bits to prevent this from happening
on e.g. r8a7791/koelsch when support for the BRG will be added.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As no platform defines an interface clock the SCI driver always falls
back to a clock named "peripheral_clk".
- On SH platforms that clock is the base clock for the SCI functional
clock and has the same frequency,
- On ARM platforms that clock doesn't exist, and clk_get() will return
the default clock for the device.
We can thus make the functional clock mandatory and drop the interface
clock.
EPROBE_DEFER is handled for clocks that may be referenced from DT (i.e.
"fck", and the deprecated "sci_ick").
Cc: devicetree@vger.kernel.org
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
[geert: Handle EPROBE_DEFER, reformat description, break long comment line]
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
To be able to make use of the mctrl-gpio helper from a module these
functions must be exported. This was forgotten in the commit introducing
support interrupt handling for these functions (while it was done for
mctrl_gpio_enable_ms, *sigh*).
Fixes: ce59e48fdb ("serial: mctrl_gpio: implement interrupt handling")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The tx_stop() call turns the interrupt off, but the tx_start() does not
check if the interrupt is enabled. Switch it back on if there is more
work to do.
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Tested-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As an attempt to stop issues with bad console output, ensure that both the
rx and tx interrupts are disabled during the console write to avoid any
problems with console and non-console being called together.
This should help with the SMP case as it should stop other cores being
signalled during the console write.
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Tested-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the meson_uart_tx_empty() instead of a direct read of the status
register. This is easier to read and will ensure the UART's transmit
state machine is idle when trying to update the baud rate.
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Tested-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since disabling the transmit state machine still allows characters to
be transmitted when written to the UART write FIFO, simply disable the
transmit interrupt when the UART port is stopped.
This has not shown an improvement with the console issues when running
systemd, but seems like it should be done.
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Reported-by: Edward Cragg <ed.cragg@codethink.co.uk>
Tested-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Ensure the UART's transmitter is enabled when meson_console_putchar is
called. If not, then the console output is corrupt (the hardware seems
to try and send /something/ even if the TX is disabled).
This fixes corrupt console output on events such as trying to reboot the
system since the console tx may be called after drivers shutdown method has
been called.
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Reported-by: Edward Cragg <edward.cragg@codethink.co.uk>
Tested-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The tx_empty() uart_op should only return empty if both the transmit fifo
and the transmit state-machine are both idle. Add a test for the hardware's
XMIT_BUSY flag.
Note, this is possibly related to an issue where the port is being shutdown
with paritally transmitted characters in it.
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Reported-by: Edward Cragg <edward.cragg@codethink.co.uk>
Tested-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the uart startup entry is called, do not reset the port as this
could cause issues with anything left in the FIFO from a previous operation
such as a console write. Move the hardware reset to probe time and simply
clear the errors before enabling the port.
This fixes the issue where the console could become corrupted as there
where characters left in the output or output fifo when a user process
such as systemd would open/close the uart to transmit characters.
For example, you get:
[ 3.252263] systemd[1]: Dete
instead of:
[ 3.338801] systemd[1]: Detected architecture arm.
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Tested-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The meson_uart_release_port() unmaps the register area but does not release
it. The meson_uart_request_port() calls devm_request_mem_region so the
release should call devm_release_mem_region() for that area so that anyt
subsequent use of these calls will work.
This fixes an issue where the addition of reset code before registering
the uart stops the console from working.
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Tested-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Using relaxed IO accessors allows GCC to better optimise this code
as we eliminate the heavy memory barriers - for example, GCC can now
cache the address of a register across a read-modify-write sequence,
rather than reloading the base address, offset and access size flag.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add (incomplete) support for the ZTE UART to the AMBA PL011 driver.
This is similar to the ARM and ST variants, except it has a different
register address layout, and requires 32-bit accesses to the registers.
Use the newly introduced register tables and access size support to
cope with these differences.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support for 32-bit register accesses to the AMBA PL011 UART. This
is needed for ZTE UARTs, which require 32-bit accesses as opposed to
the more normal 16-bit accesses.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As we can detect when the LCR register is split between TX and RX,
we don't need three entries in the table to deal with this. Reduce
this down to two entries by converting the REG_ST_LCRH_* entries to
standard REG_LCRH_* and remove REG_LCRH.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add the ST variant register offset table to the driver. Currently,
this is an identical copy of the standard version, but this will be
modified in the following changes.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add a temporary for the computed source address and substitute
where appropriate. No functional change.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Merge the multiple tty_copy_to_user() calls into a single copy
sequence within tty_copy_to_user().
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As the of-serial driver is now 8250 specific, we can move the
file to a more appropriate place in teh 8250 subdirectory and
adapt the Kconfig help text and file name.
I'm leaving the CONFIG_SERIAL_OF_PLATFORM symbol unchanged
to avoid breaking user configuration files unnecessarily.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The only other user of this code was the nwp-serial driver, but that
is now gone, so we can remove a couple of #ifdef statments in this
driver.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Geert Uytterhoeven