Cooling-maps doesn't have to be a required property because there may
be no cooling device on system, or there are no enough cooling devices for
each thermal zone in multiple thermal zone cases since cooling devices
can't be shared.
So make this property optional to remove such limitations.
For thermal zones with no cooling-maps, there could be critic trips
that can trigger CPU reset or shutdown. So they still can take actions.
Signed-off-by: Yuantian Tang <andy.tang@nxp.com>
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200309045411.21859-1-andy.tang@nxp.com
Include Cadence core DT schema and define the Cadence platform DT schema
for both Host and Endpoint mode. Note: The Cadence core DT schema could
be included for other platforms using Cadence PCIe core.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Add PCIe Host (RC) and Endpoint (EP) device tree schema for Cadence
PCIe core library. Platforms using Cadence PCIe core can include the
schemas added here in the platform specific schemas.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
The new format is called V4L2_PIX_FMT_Y14. Like V4L2_PIX_FMT_Y10 and
V4L2_PIX_FMT_Y12 it is stored in two bytes per pixel but has only two
unused bits at the top.
Signed-off-by: Daniel Glöckner <dg@emlix.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add an ioctl FS_IOC_GET_ENCRYPTION_NONCE which retrieves the nonce from
an encrypted file or directory. The nonce is the 16-byte random value
stored in the inode's encryption xattr. It is normally used together
with the master key to derive the inode's actual encryption key.
The nonces are needed by automated tests that verify the correctness of
the ciphertext on-disk. Except for the IV_INO_LBLK_64 case, there's no
way to replicate a file's ciphertext without knowing that file's nonce.
The nonces aren't secret, and the existing ciphertext verification tests
in xfstests retrieve them from disk using debugfs or dump.f2fs. But in
environments that lack these debugging tools, getting the nonces by
manually parsing the filesystem structure would be very hard.
To make this important type of testing much easier, let's just add an
ioctl that retrieves the nonce.
Link: https://lore.kernel.org/r/20200314205052.93294-2-ebiggers@kernel.org
Reviewed-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Eric Biggers <ebiggers@google.com>
Johan Hedberg says:
====================
pull request: bluetooth-next 2020-03-19
Here's the main bluetooth-next pull request for the 5.7 kernel.
- Added wideband speech support to mgmt and the ability for HCI drivers
to declare support for it.
- Added initial support for L2CAP Enhanced Credit Based Mode
- Fixed suspend handling for several use cases
- Fixed Extended Advertising related issues
- Added support for Realtek 8822CE device
- Added DT bindings for QTI chip WCN3991
- Cleanups to replace zero-length arrays with flexible-array members
- Several other smaller cleanups & fixes
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
In Certain QCOM SoCs like ipq8064, apq8064, msm8960, msm8974
that has KRAIT processors the voltage/current value of each OPP
varies based on the silicon variant in use.
The required OPP related data is determined based on
the efuse value. This is similar to the existing code for
kryo cores. So adding support for krait cores here.
Signed-off-by: Sricharan R <sricharan@codeaurora.org>
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
i.MX8/8X SCU MU is dedicated for communication between SCU
and Cortex-A cores from hardware design, it could not be reused
for other purpose. To use SCU MU more effectivly, add "fsl,imx8-scu-mu"
compatile to support fast IPC.
Reviewed-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
This mailbox hardware is present in Allwinner sun6i, sun8i, sun9i, and
sun50i SoCs. Add a device tree binding for it.
Acked-by: Maxime Ripard <mripard@kernel.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
The sram property was incorrectly added to the GMU binding when it
really belongs with the GPU binding instead. Let's go ahead and
move it.
While changes are being made here, let's update the sram property
description to mention that this property is only valid for a3xx and
a4xx GPUs. The a3xx/a4xx example in the GPU is replaced with what was
in the GMU.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Fixes: 198a72c8f9 ("dt-bindings: display: msm: gmu: add optional ocmem property")
Acked-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Fix a couple of dangling links to core-api/namespaces.rst by turning them
into proper references. Enable the autosection extension (available since
Sphinx 1.4) to make this work.
Co-developed-by: Federico Vaga <federico.vaga@vaga.pv.it>
Fixes: fcfacb9f83 ("doc: move namespaces.rst from kbuild/ to core-api/")
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Pull Kbuild fixes from Masahiro Yamada:
- fix __uint128_t capability test in Kconfig when GCC that defaults to
32-bit is used to build the 64-bit kernel
- suppress new noisy Clang warnings -Wpointer-to-enum-cast
- move the namespace field in Module.symvers for the backward
compatibility reason for the depmod tool
- use available compression for initramdisk when INTRAMFS_SOURCE is
defined, which was the original behavior
- fix modpost to handle correct large section numbers when it refers to
modversion CRCs and module namespaces
- fix comments and documents
* tag 'kbuild-fixes-v5.6-3' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
scripts/kallsyms: fix wrong kallsyms_relative_base
modpost: Get proper section index by get_secindex() instead of st_shndx
initramfs: restore default compression behavior
modpost: move the namespace field in Module.symvers last
kbuild: Disable -Wpointer-to-enum-cast
kbuild: doc: fix references to other documents
int128: fix __uint128_t compiler test in Kconfig
kconfig: introduce m32-flag and m64-flag
kbuild: Fix inconsistent comment
UAPI Changes:
On i915 we have a new UAPI to allow userspace to specify CS ring buffer size on
construction (I915_CONTEXT_PARAM_RINGSIZE) and also new sysfs entries exposing
various engine properties
GVT Changes:
VFIO edid getting expanded to all platforms and a big cleanup around attr
group, unused vblank complete, kvmgt, Intel engine and dev_priv usages.
i915 Changes:
- new UAPI to allow userspace to specify CS ring buffer size on construction
(I915_CONTEXT_PARAM_RINGSIZE) - (Chris)
- New sysfs entries exposing various engine properties (Chris)
- Tiger Lake is out of require_force_probe protection (Jose)
- Changes in many places around active requests, reset and heartbeat (Chris)
- Stop assigning drm-dev_private pointer (Jani)
- Many code refactor in many places, including intel_modeset_init,
increasing use of intel_uncore_*, vgpu, and gvt stuff (Jani)
- Fixes around display pipe iterators (Anshuman)
- Tigerlake enabling work (Matt Ropper, Matt Atwood, Ville, Lucas, Daniele,
Jose, Anusha, Vivek, Swathi, Caz. Kai)
- Code clean-up like reducing use of drm/i915_drv.h, removing unused
registers, removing garbage warns, and some other code polishing (Jani, Lucas,
Ville)
- Selftests fixes, improvements and additions (Chris, Dan, Aditya, Matt Auld)
- Fix plane possible_crtcs bit mask (Anshuman)
- Fixes and cleanup on GLK pre production identification and w/a (Ville)
- Fix display orientation on few cases (Hans, Ville)
- dbuf clean-up and improvements for slice arrays handling (Ville)
- Improvement around min cdclk calculation (Stanislav)
- Fixes and refactor around display PLLs (Imre)
- Other execlists and perf fixes (Chris)
- Documentation fixes (Jani, Chris)
- Fix build issue (Anshuman)
- Many more fixes around the locking mechanisms (Chris)
- Other fixes and debugability info around preemption (Chris, Tvrtko)
- Add mechanism to submit a context WA on ring submission (Mika)
- Clear all Eu/L3 resitual context (Prathap)
- More changes around local memory (Abdiel, Matt, Chris)
- Fix RPS (Chris)
- DP MST fix (Lyude)
- Display FBC fixes (Jose, RK)
- debugfs cleanup (Tvrtko)
- More convertion towards drm_debive based loggin (Wambui, Ram)
- Avoid potential buffer overflow (Takashi)
- Ice Lake and Elkhart Lake workarounds (Matt Roper)
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200314001535.GA2969344@intel.com
Jonathan writes:
First set of new IIO device support, fatures and cleanups for the 5.7 cycle
Includes changes for the counter subsystem
Core Feature
* Explicitly handle sysfs values in dB, including correctly handling the
needed postfix dB.
* Add a TODO to suggest suitable activities for new contributors to IIO now
the vast majority of drivers are out of staging (and the remaining ones
there are 'hard'). Also update the TODO in staging to remove stale entries.
Staging graduations
* ad7192 ADC.
New device support
* ad5770r
- New driver for this 6 channel DAC including DT bindings.
* ad8366
- Add supprot for the hmc1119 attenuator.
* al3010
- New driver supporting this Dyna-image light sensors.
- Power management and DT bindings added in additional patches.
* atlas-sensor
- Add support for atlas DO-SM device. Reads disolved oxygen in a solution.
* gpap002x00f
- New driver and bindings to support the GP2AP002A00F and GP2AP002S00F light
and proximity sensors. There is some limited existing support in
input. The intent is to drop this driver once IIO driver is in place.
* hmc425a
- New driver for this attenuator.
* icp10100
- New driver for this presure sensor.
* ltc2632
- Add support for the ltc2636 8 channel DAC. Includes bindings and some
tidying up of the driver.
* inv_mpu6050
- Support IAM20680, ICM20609, ICM20689 and ICM20690.
Includes related tidy up and rework of low pass filter bandwidth
handling to give suitable values for all chips.
Binding conversions to yaml or missing bindings docs.
* atlas-sensor, including consolidation of previous 3 separate docs into 1.
* ad7923, previously no doc.
* max1363, split into max1238 and max1363 to simplify yaml.
* stm32-adc
Features
* (counter) 104-quad-8
- Support a filter clock prescaler.
- Support reporting of encoder cable status.
* ad7124
- Low pass filter support.
- Debugfs interface to access registers directly.
* ad8366
- Support control of hardware gain.
* inv_mpu6050
- Runtime pm with autosuspend.
* npcm adc
- Add reset support. This is a breaking change if DT is not in sync,
however this device is a BMC so the ecosystem is closed enought that
this should not be a problem.
* srf04
- Add power management with DT bindings for the GPIO.
* stm32-timer-trigger
- Power management.
* (counter) stm32-timer-cnt
- Power management.
* vcnl4000
- Enable runtime PM for devices that don't use on demand measurement.
Cleanups and minor fixes
* core
- Avoid double read when using debugfs. Whilst we provide no guarantees
on lack of side effects using the debugfs interfaces, this one is
generate unexpected results so let us tidy it up.
* dac/Kconfig
- Alphabetic order.
* ad5755
- Grammar and minor other fixes.
* ad7124
- Fail probe if get_voltage fails as no meaningful readings can be had
without knowing the external reference.
- Switch to selection between different channel attributes rather than
building the arrays at runtime.
- Remove the spi_device_id table as the driver cannot be probled without
more information that can be provided without dt.
- Update sysfs docs to provide more inormation and bring remaining docs for
this part out of staging.
* ad9292
- Use new SPI transfer delay structure.
* adis library
- Add unlocked version of adis_initial_startup and refactor the function.
- Add a product ID santiy check.
- Add support for different self test registers.
- Use new SPI delay structure.
- Add new docs and tidy up existing.
* adis16136
- Initialize adis_data statically.
* adis16400
- Initialize adis_data statically.
* adis16460
- Use core __adis_initial_Startup now it supports everything needed.
* adis16480
- Initialize adis_data statically.
- Use core __adis_initial_startup now it supports everything needed.
* al3320a
- Add missing DT binding docs.
- Tidy up code formatting.
- Simplify error paths using devm_add_action_or_reset.
- Ensure autoloading works by adding the of_match_table.
* atlas-sensor
- Drop false requirement for interrupt line, the value can be polled using
a sysfs or hrtimer type trigger.
* exynos-adc
- Silence warning message on deferring probe.
* gp2ap002
- Greatly simplify the Lux LUT.
- Reorder actions around buffer setup and tear down as part of a sub-system
wide standardization of these.
* inv_mpu6050
- Various lttle tidyups.
- Simpliy I2C aux MUX handling by enabling it only at startup. It never
needs to be disabled.
- Simplify polling rate when magnetometer enabled by putting only under
control of userspace.
- Always execute full reset on devices supporting spi. It does no harm
when using i2c and makes for simpler code.
- Reduce over the top sleep times for vddio regulator power up.
- Greatly simplify power and engine management.
- Fix some delays in polled reads (only visible due to other changes)
- Stop preventing sampling rate changes whilst running as there is no
adverse consequence of doing so.
- Prevent attempting to read the temperature if neither accel nor
gyro is enabled.
* lmp9100
- Reorder actions around buffer setup and tear down as part of a sub-system
wide standardization of these.
* max1118
- Use new SPI transfer delay structure.
* mcp320x
- Use new SPI transfer delay structure.
* si1133
- Read full 24 bit signed integer instead o dropping last 8 bits of value.
Not a critical fix as just adds precision.
* st_sensors
- Use st_sensors_dev_name_probe instead of open coded version in st_accel
- Handle potential memory allocation failure.
* st_lsm6dsx
- Fix some wrong structure element naming in documentation.
- Add missing return value check.
* stm32_timer_cnt
- Drop some unused left over IIO headers from this count subsystem driver.
- Ensure the clock is enabled in master mode. Theoretical issue rather
than one known to happen in the wild.
* tlc4541
- Use new SPI delay structure.
* tag 'iio-5.7a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio: (98 commits)
iio: dac: Kconfig: sort symbols alphabetically
iio: light: gp2ap020a00f: fix iio_triggered_buffer_{predisable,postenable} positions
iio: potentiostat: lmp9100: fix iio_triggered_buffer_{predisable,postenable} positions
iio: trigger: stm32-timer: add power management support
iio: trigger: stm32-timer: rename enabled flag
iio: add a TODO
counter: 104-quad-8: Support Differential Encoder Cable Status
counter: 104-quad-8: Support Filter Clock Prescaler
iio: pressure: icp10100: add driver for InvenSense ICP-101xx
iio: industrialio-core: Fix debugfs read
iio: imu: adis: add a note better explaining state_lock
iio: imu: adis: update 'adis_data' struct doc-string
iio: imu: adis: add doc-string for 'adis' struct
iio: imu: adis_buffer: Use new structure for SPI transfer delays
iio: adc: ti-tlc4541: Use new structure for SPI transfer delays
iio: adc: mcp320x: Use new structure for SPI transfer delays
iio: adc: max1118: Use new structure for SPI transfer delays
iio: adc: ad9292: Use new structure for SPI transfer delays
iio: adc: exynos: Silence warning about regulators during deferred probe
staging: iio: update TODO
...
Add the Enterprise MAC support to the list of supported IP versions and
the newly added XLGMII interface support.
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While looking at the binfmt-misc documentation I noticed that there is a
reference to the “java” example that could be a direct link.
This patch simply adds the link without changing the HTML output.
Signed-off-by: Romuald Brunet <romuald@chivil.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
In order to preserve backwards compatability with kmod tools, we have to
move the namespace field in Module.symvers last, as the depmod -e -E
option looks at the first three fields in Module.symvers to check symbol
versions (and it's expected they stay in the original order of crc,
symbol, module).
In addition, update an ancient comment above read_dump() in modpost that
suggested that the export type field in Module.symvers was optional. I
suspect that there were historical reasons behind that comment that are
no longer accurate. We have been unconditionally printing the export
type since 2.6.18 (commit bd5cbcedf4), which is over a decade ago now.
Fix up read_dump() to treat each field as non-optional. I suspect the
original read_dump() code treated the export field as optional in order
to support pre <= 2.6.18 Module.symvers (which did not have the export
type field). Note that although symbol namespaces are optional, the
field will not be omitted from Module.symvers if a symbol does not have
a namespace. In this case, the field will simply be empty and the next
delimiter or end of line will follow.
Cc: stable@vger.kernel.org
Fixes: cb9b55d21f ("modpost: add support for symbol namespaces")
Tested-by: Matthias Maennich <maennich@google.com>
Reviewed-by: Matthias Maennich <maennich@google.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Jessica Yu <jeyu@kernel.org>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
MP8867 is an I2C-controlled adjustable voltage regulator made by
Monolithic Power Systems. The difference between MP8867 and MP8869
are:
1.If V_BOOT, the vref of MP8869 is fixed at 600mv while vref of MP8867
is determined by the I2C control.
2.For MP8867, when setting voltage, if the steps is within 5, we need
to manually set the GO_BIT to 0.
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Link: https://lore.kernel.org/r/20200316223100.37805b22@xhacker
Signed-off-by: Mark Brown <broonie@kernel.org>
KVM: s390: Features and Enhancements for 5.7 part1
1. Allow to disable gisa
2. protected virtual machines
Protected VMs (PVM) are KVM VMs, where KVM can't access the VM's
state like guest memory and guest registers anymore. Instead the
PVMs are mostly managed by a new entity called Ultravisor (UV),
which provides an API, so KVM and the PV can request management
actions.
PVMs are encrypted at rest and protected from hypervisor access
while running. They switch from a normal operation into protected
mode, so we can still use the standard boot process to load a
encrypted blob and then move it into protected mode.
Rebooting is only possible by passing through the unprotected/normal
mode and switching to protected again.
One mm related patch will go via Andrews mm tree ( mm/gup/writeback:
add callbacks for inaccessible pages)
Clarify locking.rst to mention early that we're not enabling fast page
fault for indirect sps. The previous wording is confusing, in that it
seems the proposed solution has been already implemented but it has not.
Signed-off-by: Peter Xu <peterx@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Remove the code for handling stateful CPUID 0x2 and mark the associated
flags as deprecated. WARN if host CPUID 0x2.0.AL > 1, i.e. if by some
miracle a host with stateful CPUID 0x2 is encountered.
No known CPU exists that supports hardware accelerated virtualization
_and_ a stateful CPUID 0x2. Barring an extremely contrived nested
virtualization scenario, stateful CPUID support is dead code.
Suggested-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Suggested-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
It could take kvm->mmu_lock for an extended period of time when
enabling dirty log for the first time. The main cost is to clear
all the D-bits of last level SPTEs. This situation can benefit from
manual dirty log protect as well, which can reduce the mmu_lock
time taken. The sequence is like this:
1. Initialize all the bits of the dirty bitmap to 1 when enabling
dirty log for the first time
2. Only write protect the huge pages
3. KVM_GET_DIRTY_LOG returns the dirty bitmap info
4. KVM_CLEAR_DIRTY_LOG will clear D-bit for each of the leaf level
SPTEs gradually in small chunks
Under the Intel(R) Xeon(R) Gold 6152 CPU @ 2.10GHz environment,
I did some tests with a 128G windows VM and counted the time taken
of memory_global_dirty_log_start, here is the numbers:
VM Size Before After optimization
128G 460ms 10ms
Signed-off-by: Jay Zhou <jianjay.zhou@huawei.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Felipe writes:
USB: changes for v5.7 merge window
Lots of changes on dwc3 this time, most of them from Thinh fixing a
bunch of really old mishaps on the driver.
DWC2 got support for STM32MP15 and a couple RockChip SoCs while DWC3
learned about Amlogic A1 family.
Apart from these, we have a few spelling fixes and other minor
non-critical fixes all over the place.
Signed-off-by: Felipe Balbi <balbi@kernel.org>
* tag 'usb-for-v5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb: (41 commits)
dt-bindings: usb: add documentation for aspeed usb-vhub
ARM: dts: aspeed-g4: add vhub port and endpoint properties
ARM: dts: aspeed-g5: add vhub port and endpoint properties
ARM: dts: aspeed-g6: add usb functions
usb: gadget: aspeed: add ast2600 vhub support
usb: gadget: aspeed: read vhub properties from device tree
usb: gadget: aspeed: support per-vhub usb descriptors
usb: gadget: f_phonet: Replace zero-length array with flexible-array member
usb: gadget: composite: Inform controller driver of self-powered
usb: gadget: amd5536udc: fix spelling mistake "reserverd" -> "reserved"
udc: s3c-hsudc: Silence warning about supplies during deferred probe
usb: dwc2: Silence warning about supplies during deferred probe
dt-bindings: usb: dwc2: add compatible property for rk3368 usb
dt-bindings: usb: dwc2: add compatible property for rk3328 usb
usb: gadget: add raw-gadget interface
usb: dwc2: Implement set_selfpowered()
usb: dwc3: qcom: Replace <linux/clk-provider.h> by <linux/of_clk.h>
usb: dwc3: core: don't do suspend for device mode if already suspended
usb: dwc3: Rework resets initialization to be more flexible
usb: dwc3: Rework clock initialization to be more flexible
...
ath.git patches for v5.7. Major changes:
ath10k
* support for getting btcoex settings from Device Tree
* support QCA9377 SDIO device
ath11k
* add HE rate accounting
* add thermal sensor and cooling devices
Pull irq fix from Thomas Gleixner:
"A single commit to handle an erratum in Cavium ThunderX to prevent
access to GIC registers which are broken in the implementation"
* tag 'irq-urgent-2020-03-15' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqchip/gic-v3: Workaround Cavium erratum 38539 when reading GICD_TYPER2
Add device tree binding documentation for the Aspeed USB 2.0 Virtual HUb
Controller.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Tao Ren <rentao.bupt@gmail.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
A test with the command below gives for example this error:
arch/arm64/boot/dts/rockchip/rk3368-evb-act8846.dt.yaml: usb@ff580000:
compatible:
['rockchip,rk3368-usb', 'rockchip,rk3066-usb', 'snps,dwc2']
is not valid under any of the given schemas
The compatible property for rk3368 dwc2 usb was somehow never added to
the documention. Fix this error by adding
'rockchip,rk3368-usb', 'rockchip,rk3066-usb', 'snps,dwc2'
to dwc2.yaml.
make ARCH=arm64 dtbs_check
DT_SCHEMA_FILES=Documentation/devicetree/bindings/usb/dwc2.yaml
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
A test with the command below gives for example this error:
arch/arm64/boot/dts/rockchip/rk3328-evb.dt.yaml: usb@ff580000:
compatible:
['rockchip,rk3328-usb', 'rockchip,rk3066-usb', 'snps,dwc2']
is not valid under any of the given schemas
The compatible property for rk3328 dwc2 usb was somehow never added to
the documention. Fix this error by adding
'rockchip,rk3328-usb', 'rockchip,rk3066-usb', 'snps,dwc2'
to dwc2.yaml.
make ARCH=arm64 dtbs_check
DT_SCHEMA_FILES=Documentation/devicetree/bindings/usb/dwc2.yaml
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
USB Raw Gadget is a kernel module that provides a userspace interface for
the USB Gadget subsystem. Essentially it allows to emulate USB devices
from userspace. Enabled with CONFIG_USB_RAW_GADGET. Raw Gadget is
currently a strictly debugging feature and shouldn't be used in
production.
Raw Gadget is similar to GadgetFS, but provides a more low-level and
direct access to the USB Gadget layer for the userspace. The key
differences are:
1. Every USB request is passed to the userspace to get a response, while
GadgetFS responds to some USB requests internally based on the provided
descriptors. However note, that the UDC driver might respond to some
requests on its own and never forward them to the Gadget layer.
2. GadgetFS performs some sanity checks on the provided USB descriptors,
while Raw Gadget allows you to provide arbitrary data as responses to
USB requests.
3. Raw Gadget provides a way to select a UDC device/driver to bind to,
while GadgetFS currently binds to the first available UDC.
4. Raw Gadget uses predictable endpoint names (handles) across different
UDCs (as long as UDCs have enough endpoints of each required transfer
type).
5. Raw Gadget has ioctl-based interface instead of a filesystem-based one.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Yuantian Tang