The hardware expects MT_TX_RATE_NSS to be filled with the number of
space/time streams. For non-STBC rates, this is equal to nss.
For 1-stream STBC, this needs to be set to 2.
This is relevant for VHT rates only, on HT, the value is derived from MCS
internally.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Fix typo setting urb->transfer_buffer_length in mt76u_fill_rx_sg
Fixes: b40b15e152 ("mt76: add usb support to mt76 layer")
Fixes: f8f527b16d ("mt76: usb: use EP max packet aligned buffer sizes for rx")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
- Store the previous and current rate set in the driver + the TSF value
at the time of the switch.
- Use the tx status TSF value to determine which rate set needs to be used
as reference.
- Report only short or long GI rates for a single status event, not a mix.
- The hardware reports the last used rate index. Use it along with the
retry count to figure out what rate was used for the first attempt.
- Use the same retry count value for all rate slots to make this calculation
work.
- Derive the probe rate from the current rateset instead of the skb cb
- Do not wait for a status report for the probe frame before removing the
probe rate from the rate table. Do it immediately after it was referenced
in a tx status report.
- Use the first half of the first rate retry budget for the probe rate
in order to avoid using too many retries on that rate
- Switch from lower rates to higher rates more conservatively
- enable hardware rate up/down selection
Reviewed-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
These values must be initialized to zero, otherwise the hardware could
reuse previous values, especially the rate index
Reviewed-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
It bypasses the MCU, so it does not belong in mcu.c
Also make mt7615_mac_tx_rate_val static
Reviewed-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Add mt7615_mcu_send_ram_firmware routine since mt7615_load_ram runs the
same code to send ram firmware to cr4 and n9 mcus. Moreover rename
gen_dl_mode in mt7615_mcu_gen_dl_mode.
This patch does not introduce any behaviour change, it is just code
refactor.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Release patch semaphore even if request_firmware fails in
mt7615_load_patch
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Since we don't clean that tx queue from the tx tasklet, we need to do it
after the firmware upload is done. This patch also adds a cleanup step during
the upload, to help reclaim memory faster.
Fixes unprocessed queued frames eating up memory long after the firmware
upload has already completed
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Introduce mt7615_mcu_rdd_send_pattern routine to trigger a radar pattern
detection. Moreover move debugfs related routines in a dedicated source
file.
Suggested-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Add Channel Switch Announcement support to mt7615 driver updating beacon
template with CSA IE received from mac80211
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Delay channel calibration after Channel Availability Check. Add some
code cleanup to mt7615_mcu_set_channel
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Add hw radar detection support to mt7615 driver in order to
unlock dfs channels on 5GHz band
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Introduce mt7615_regd_notifier callback. This is a preliminary patch to
add radar detection support to mt7615 driver
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Fix the following sparse warning in __mt7615_mcu_msg_send:
drivers/net/wireless/mediatek/mt76/mt7615/mcu.c:78:15: sparse: warning:
restricted __le16 degrades to integer
drivers/net/wireless/mediatek/mt76/mt7615/mcu.c:78:15: sparse: warning:
cast from restricted __le16
Fixes: 04b8e65922 ("mt76: add mac80211 driver for MT7615 PCIe-based chipsets")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
When beacon length is not a multiple of 4, the beacon could be sent with
the last 1-3 bytes corrupted. The skb data is guaranteed to have enough
room for reading beyond the end, because it is always followed by
skb_shared_info, so rounding up is safe.
All other callers of mt76_wr_copy have multiple-of-4 length already.
Cc: stable@vger.kernel.org
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The `ar_usb` field of `ath6kl_usb_pipe_usb_pipe` objects
are initialized to point to the containing `ath6kl_usb` object
according to endpoint descriptors read from the device side, as shown
below in `ath6kl_usb_setup_pipe_resources`:
for (i = 0; i < iface_desc->desc.bNumEndpoints; ++i) {
endpoint = &iface_desc->endpoint[i].desc;
// get the address from endpoint descriptor
pipe_num = ath6kl_usb_get_logical_pipe_num(ar_usb,
endpoint->bEndpointAddress,
&urbcount);
......
// select the pipe object
pipe = &ar_usb->pipes[pipe_num];
// initialize the ar_usb field
pipe->ar_usb = ar_usb;
}
The driver assumes that the addresses reported in endpoint
descriptors from device side to be complete. If a device is
malicious and does not report complete addresses, it may trigger
NULL-ptr-deref `ath6kl_usb_alloc_urb_from_pipe` and
`ath6kl_usb_free_urb_to_pipe`.
This patch fixes the bug by preventing potential NULL-ptr-deref
(CVE-2019-15098).
Signed-off-by: Hui Peng <benquike@gmail.com>
Reported-by: Hui Peng <benquike@gmail.com>
Reported-by: Mathias Payer <mathias.payer@nebelwelt.net>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
clang triggers a warning about oversized stack frames that gcc does not
notice because of slightly different inlining decisions:
ath/wcn36xx/smd.c:1409:5: error: stack frame size of 1040 bytes in function 'wcn36xx_smd_config_bss' [-Werror,-Wframe-larger-than=]
ath/wcn36xx/smd.c:640:5: error: stack frame size of 1032 bytes in function 'wcn36xx_smd_start_hw_scan' [-Werror,-Wframe-larger-than=]
Basically the wcn36xx_hal_start_scan_offload_req_msg,
wcn36xx_hal_config_bss_req_msg_v1, and wcn36xx_hal_config_bss_req_msg
structures are too large to be put on the kernel stack, but small
enough that gcc does not warn about them.
Use kzalloc() to allocate them all. There are similar structures in other
parts of this driver, but they are all smaller, with the next largest
stack frame at 480 bytes for wcn36xx_smd_send_beacon.
Fixes: 8e84c25821 ("wcn36xx: mac80211 driver for Qualcomm WCN3660/WCN3680 hardware")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In ath6kl_htc_mbox_create(), when kzalloc() on line 2855 fails,
target->dev is assigned to NULL, and ath6kl_htc_mbox_cleanup(target) is
called on line 2885.
In ath6kl_htc_mbox_cleanup(), target->dev is used on line 2895:
ath6kl_hif_cleanup_scatter(target->dev->ar);
Thus, a null-pointer dereference may occur.
To fix this bug, kfree(target) is called and NULL is returned when
kzalloc() on line 2855 fails.
This bug is found by a static analysis tool STCheck written by us.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Initialize acktimeout to the maximum configurable value in
ath_dynack_reset in order to not disconnect long distance static links
enabling dynack and even to take care of possible errors configuring
a static timeout. Moreover initialize station timeout value to the current
acktimeout value
Tested-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add compute timeout to last computation timestamp in
ath_dynack_reset in order to not run ath_dynack_compute_ackto
immediately
Tested-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Introduce ath_dynack_set_timeout routine to configure slottime/ack/cts
timeouts and remove duplicated code
Tested-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Atheros cards with a AR92XX generation (and older) chip usually
store their pci(e) initialization vectors on an external eeprom chip.
However these chips technically don't need the eeprom chip attached,
the AR9280 Datasheet in section "6.1.2 DEVICE_ID" describes that
"... if the EEPROM content is not valid, a value of 0xFF1C returns
when read from the register". So, they will show up on the system's
pci bus. However in that state, ath9k can't load, since it relies
on having the correct pci-id, otherwise it doesn't know what chip it
actually is. This happens on many embedded devices like routers
and accesspoint since they want to keep the BOM low and store the
pci(e) initialization vectors together with the calibration data
on the system's FLASH, which is out of reach of the ath9k chip.
Furthermore, Some devices (like the Cisco Meraki Z1 Cloud Managed
Teleworker Gateway) need to be able to initialize the PCIe wifi device.
Normally, this should be done as a pci quirk during the early stages of
booting linux. However, this isn't possible for devices which have the
init code for the Atheros chip stored on NAND in an UBI volume.
Hence, this module can be used to initialize the chip when the
user-space is ready to extract the init code.
Martin Blumenstingl prodived the following fixes:
owl-loader: add support for OWL emulation PCI devices
owl-loader: don't re-scan the bus when ath9k_pci_fixup failed
owl-loader: use dev_* instead of pr_* logging functions
owl-loader: auto-generate the eeprom filename as fallback
owl-loader: add a debug message when swapping the eeprom data
owl-loader: add missing newlines in log messages
Reviewed-by: Julian Calaby <julian.calaby@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/wireless/ath/carl9170/usb.c: In function carl9170_usb_disconnect:
drivers/net/wireless/ath/carl9170/usb.c:1110:21:
warning: variable udev set but not used [-Wunused-but-set-variable]
It is not use since commit feb09b2933 ("carl9170:
fix misuse of device driver API")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
A null pointer would be passed to a call of the function “kfree”
directly after a call of the function “kcalloc” failed at one place.
Remove this superfluous function call.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Reviewed-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add support for Enhanced Directional Multi-Gigabit (EDMG) channels 9-11.
wil6210 reports it's EDMG capabilities (that are also based on FW
capability) to cfg80211 by filling
wiphy->bands[NL80211_BAND_60GHZ]->edmg_cap.
wil6210 handles edmg.channels and edmg.bw_config requested in connect
and start_ap operations.
Signed-off-by: Alexei Avshalom Lazar <ailizaro@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
There are several occasions where a negative cid value is passed
into wil_cid_valid and this is converted into a u8 causing the
range check of cid >= 0 to always succeed. Fix this by making
the cid argument an int to handle any -ve error value of cid.
An example of this behaviour is in wil_cfg80211_dump_station,
where cid is assigned -ENOENT if the call to wil_find_cid_by_idx
fails, and this -ve value is passed to wil_cid_valid. I believe
that the conversion of -ENOENT to the u8 value 254 which is
greater than wil->max_assoc_sta causes wil_find_cid_by_idx to
currently work fine, but I think is by luck and not the
intended behaviour.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
`dev` (struct rsi_91x_usbdev *) field of adapter
(struct rsi_91x_usbdev *) is allocated and initialized in
`rsi_init_usb_interface`. If any error is detected in information
read from the device side, `rsi_init_usb_interface` will be
freed. However, in the higher level error handling code in
`rsi_probe`, if error is detected, `rsi_91x_deinit` is called
again, in which `dev` will be freed again, resulting double free.
This patch fixes the double free by removing the free operation on
`dev` in `rsi_init_usb_interface`, because `rsi_91x_deinit` is also
used in `rsi_disconnect`, in that code path, the `dev` field is not
(and thus needs to be) freed.
This bug was found in v4.19, but is also present in the latest version
of kernel. Fixes CVE-2019-15504.
Reported-by: Hui Peng <benquike@gmail.com>
Reported-by: Mathias Payer <mathias.payer@nebelwelt.net>
Signed-off-by: Hui Peng <benquike@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This reverts commit 9ad3b55654.
As reported by Sergey:
"I got some problem after upgrade kernel to 5.2 version (debian testing
linux-image-5.2.0-2-amd64). 5Ghz client stopped to see AP.
Some tests with 1metre distance between client-AP: 2.4Ghz -22dBm, for
5Ghz - 53dBm !, for longer distance (8m + walls) 2.4 - 61dBm, 5Ghz not
visible."
It was identified that rx signal level degradation was caused by
9ad3b55654 ("rt2800: enable TX_PIN_CFG_LNA_PE_ bits per band").
So revert this commit.
Cc: <stable@vger.kernel.org> # v5.1+
Reported-and-tested-by: Sergey Maranchuk <slav0nic0@gmail.com>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
After looking at code I realized that my previous fix
9584412438 ("rt2x00: clear IV's on start to fix AP mode regression")
was incomplete. We can still have wrong IV's after re-keyring.
To fix that, clear up IV's also on key removal.
Fixes: 710e6cc159 ("rt2800: do not nullify initialization vector data")
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
tested-by: Emil Karlson <jekarl@iki.fi>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
We were erroneously assigning the new configuration to a local
variable cfg, but that was not being assigned to anything, so the
change was getting lost. Assign directly to iwl_trans->cfg instead.
Fixes: 5a8c31aa63 ("iwlwifi: pcie: fix recognition of QuZ devices")
Cc: stable@vger.kernel.org # 5.2
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
mwifiex_update_vs_ie(),mwifiex_set_uap_rates() and
mwifiex_set_wmm_params() call memcpy() without checking
the destination size.Since the source is given from
user-space, this may trigger a heap buffer overflow.
Fix them by putting the length check before performing memcpy().
This fix addresses CVE-2019-14814,CVE-2019-14815,CVE-2019-14816.
Signed-off-by: Wen Huang <huangwenabc@gmail.com>
Acked-by: Ganapathi Bhat <gbhat@marvell.comg>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
MT7630E hardware does support 5GHz, but we do not properly configure phy
for 5GHz channels. Scanning at this band not only do not show any APs
but also can hang the firmware.
Since vendor reference driver do not support 5GHz we don't know how
properly configure 5GHz channels. So disable this band for MT7630E .
Cc: stable@vger.kernel.org
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Since 41634aa8d6 ("mt76: only schedule txqs from the tx tasklet")
I can observe firmware hangs on MT7630E on station mode: tx stop
functioning after minor activity (rx keep working) and on module
unload device fail to stop with messages:
[ 5446.141413] mt76x0e 0000:06:00.0: TX DMA did not stop
[ 5449.176764] mt76x0e 0000:06:00.0: TX DMA did not stop
Loading module again results in failure to associate with AP.
Only machine power off / power on cycle can make device work again.
It's unclear why commit 41634aa8d6 causes the problem, but it is
related to HW encryption. Since issue is a firmware hang, that is super
hard to debug, just disable HW encryption as fix for the issue.
Fixes: 41634aa8d6 ("mt76: only schedule txqs from the tx tasklet")
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array. For example:
struct usb_int_regs {
...
struct reg_data regs[0];
} __packed;
Make use of the struct_size() helper instead of an open-coded version
in order to avoid any potential type mistakes.
So, replace the following function:
static int usb_int_regs_length(unsigned int count)
{
return sizeof(struct usb_int_regs) + count * sizeof(struct reg_data);
}
with:
struct_size(regs, regs, count)
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Getting RAM info just once per driver's lifetime (during chip
recognition) is not enough as it may get adjusted later (depending on
the used firmware). Subsequent inits may load different firmwares so a
full RAM recognition is required on every PCIe setup. This is especially
important since implementing hardware reset on a firmware crash.
Moreover calling brcmf_chip_get_raminfo() makes sure that RAM core is
up. It's important as having BCMA_CORE_SYS_MEM down on BCM4366 was
resulting in firmware failing to initialize and following error:
[ 65.657546] brcmfmac 0000:01:00.0: brcmf_pcie_download_fw_nvram: Invalid shared RAM address 0x04000001
This change makes brcmf_chip_get_raminfo() call during chip recognition
redundant for PCIe devices but SDIO and USB still need it and it's a
very small overhead anyway.
Fixes: 4684997d9e ("brcmfmac: reset PCIe bus on a firmware crash")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The strncpy() may truncate the copied string,
replace it by the safer strscpy().
To avoid below compile warning with gcc 8.2:
drivers/net/wireless/broadcom/brcm80211/brcmfmac/cfg80211.c:In function 'brcmf_vndr_ie':
drivers/net/wireless/broadcom/brcm80211/brcmfmac/cfg80211.c:4227:2:
warning: 'strncpy' output truncated before terminating nul copying 3 bytes from a string of the same length [-Wstringop-truncation]
strncpy(iebuf, add_del_cmd, VNDR_IE_CMD_LEN - 1);
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Signed-off-by: Xulin Sun <xulin.sun@windriver.com>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
According to documentation IEEE80211_TX_STAT_AMPDU_NO_BACK is suppose
to be used when we do not recive BA (BlockAck). However on rt2x00 we
use it when remote station fail to decode one or more subframes within
AMPDU (some bits are not set in BlockAck bitmap). Setting the flag result
in sent of BAR (BlockAck Request) frame and this might result of abuse
of BA session, since remote station can sent BA with incorrect
sequence numbers after receiving BAR. This problem is visible especially
when connecting two rt2800 devices.
Previously I observed some performance benefits when using the flag
when connecting with iwlwifi devices. But currently possibly due
to reacent changes in rt2x00 removing the flag has no effect on
those test cases.
So remove the IEEE80211_TX_STAT_AMPDU_NO_BACK.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In proc_BSSList_open(), 'file->private_data' is allocated through kzalloc()
and 'data->rbuffer' is allocated through kmalloc(). In the following
execution, if an error occurs, they are not deallocated, leading to memory
leaks. To fix this issue, free the allocated memory regions before
returning the error.
Signed-off-by: Wenwen Wang <wenwen@cs.uga.edu>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The pointer hash is being initialized with a value that is never read
and is being re-assigned a little later on. The assignment is
redundant and hence can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In wlc_phy_radio_init_2056(), regs_SYN_2056_ptr, regs_TX_2056_ptr and
regs_RX_2056_ptr may be not assigned, and thus they are still NULL.
Then, they are used on lines 20042-20050:
wlc_phy_init_radio_regs(pi, regs_SYN_2056_ptr, (u16) RADIO_2056_SYN);
wlc_phy_init_radio_regs(pi, regs_TX_2056_ptr, (u16) RADIO_2056_TX0);
wlc_phy_init_radio_regs(pi, regs_TX_2056_ptr, (u16) RADIO_2056_TX1);
wlc_phy_init_radio_regs(pi, regs_RX_2056_ptr, (u16) RADIO_2056_RX0);
wlc_phy_init_radio_regs(pi, regs_RX_2056_ptr, (u16) RADIO_2056_RX1);
Thus, possible null-pointer dereferences may occur.
To avoid these bugs, when these variables are not assigned,
wlc_phy_radio_init_2056() directly returns.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
MSI interrupt should be enabled on certain platform.
Add a module parameter disable_msi to disable MSI interrupt,
driver will then use legacy interrupt instead.
One could rebind the PCI device, probe() will pick up the
new value of the module parameter. Such as:
echo '0000:01:00.0' > /sys/bus/pci/drivers/rtw_pci/unbind
echo '0000:01:00.0' > /sys/bus/pci/drivers/rtw_pci/bind
Tested-by: Ján Veselý <jano.vesely@gmail.com>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Reviewed-by: Daniel Drake <drake@endlessm.com>
Signed-off-by: Yu-Yen Ting <steventing@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
There is a mass of jobs between spin lock and unlock in the hardware
IRQ which will occupy much time originally. To make system work more
efficiently, this patch moves the jobs to the soft IRQ (bottom half) to
reduce the time in hardware IRQ.
Signed-off-by: Jian-Hong Pan <jian-hong@endlessm.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Pointer debugfs_topdir is initialized to a value that is never read
and it is re-assigned later. The initialization is redundant and can
be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
0day reports:
sparse warnings:
drivers/net/wireless/realtek/rtw88/coex.c:2457:6: sparse:
symbol 'rtw_coex_coex_dm_reset' was not declared. Should it be static?
rtw_coex_coex_dm_reset() is not called. Remove it.
Fixes: 4136214f7c ("rtw88: add BT co-existence support")
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Guenter Roeck <groeck@chromium.org>
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Felix Fietkau