The calibration data for devices w/o a separate
EEPROM chip can be specified via the 'eeprom_data'
field of 'ath9k_platform_data'. The 'eeprom_data'
is usually filled from board specific setup
functions. It is easy if the EEPROM data is mapped
to the memory, but it can be complicated if it is
stored elsewhere.
The patch adds support for loading of the EEPROM
data via the firmware API to avoid this limitation.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This reverts commits a50915394f and
d7c3b937bd.
This is a revert of a revert of a revert. In addition, it reverts the
even older i915 change to stop using the __GFP_NO_KSWAPD flag due to the
original commits in linux-next.
It turns out that the original patch really was bogus, and that the
original revert was the correct thing to do after all. We thought we
had fixed the problem, and then reverted the revert, but the problem
really is fundamental: waking up kswapd simply isn't the right thing to
do, and direct reclaim sometimes simply _is_ the right thing to do.
When certain allocations fail, we simply should try some direct reclaim,
and if that fails, fail the allocation. That's the right thing to do
for THP allocations, which can easily fail, and the GPU allocations want
to do that too.
So starting kswapd is sometimes simply wrong, and removing the flag that
said "don't start kswapd" was a mistake. Let's hope we never revisit
this mistake again - and certainly not this many times ;)
Acked-by: Mel Gorman <mgorman@suse.de>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Cc: Rik van Riel <riel@redhat.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use phys_addr_t rather than "void *" for physical memory address.
This removes casts and fixes a "cast from pointer to integer of different
size" warning on ppc44x_defconfig.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Technologic Systems TS-5500 provides digital I/O lines exposed through
pin blocks. On this platform, there are three of them, named DIO1, DIO2
and LCD port, that may be used as a DIO block.
The TS-5500 pin blocks are described in the product's wiki:
http://wiki.embeddedarm.com/wiki/TS-5500#Digital_I.2FO
This driver is not limited to the TS-5500 blocks. It can be extended to
support similar boards pin blocks, such as on the TS-5600.
This patch is the V2 of the previous https://lkml.org/lkml/2012/9/25/671
with corrections suggested by Linus Walleij.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: Jerome Oufella <jerome.oufella@savoirfairelinux.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
All items on the lru list are always reservable, so this is a stupid
thing to keep. Not only that, it is used in a way which would
guarantee deadlocks if it were ever to be set to block on reserve.
This is a lot of churn, but mostly because of the removal of the
argument which can be nested arbitrarily deeply in many places.
No change of code in this patch except removal of the no_wait_reserve
argument, the previous patch removed the use of no_wait_reserve.
v2:
- Warn if -EBUSY is returned on reservation, all objects on the list
should be reservable. Adjusted patch slightly due to conflicts.
v3:
- Focus on no_wait_reserve removal only.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@canonical.com>
Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Alex writes:
Pretty minor -next pull request. We some additional new bits waiting
internally for release. Hopefully Monday we can get at least some of
them out. The others will probably take a few more weeks.
Highlights of the current request:
- ELD registers for passing audio information to the sound hardware
- Handle GPUVM page faults more gracefully
- Misc fixes
Merge radeon test
* 'drm-next-3.8' of git://people.freedesktop.org/~agd5f/linux: (483 commits)
drm/radeon: bump driver version for new info ioctl requests
drm/radeon: fix eDP clk and lane setup for scaled modes
drm/radeon: add new INFO ioctl requests
drm/radeon/dce32+: use fractional fb dividers for high clocks
drm/radeon: use cached memory when evicting for vram on non agp
drm/radeon: add a CS flag END_OF_FRAME
drm/radeon: stop page faults from hanging the system (v2)
drm/radeon/dce4/5: add registers for ELD handling
drm/radeon/dce3.2: add registers for ELD handling
radeon: fix pll/ctrc mapping on dce2 and dce3 hardware
Linux 3.7-rc7
powerpc/eeh: Do not invalidate PE properly
Revert "drm/i915: enable rc6 on ilk again"
ALSA: hda - Fix build without CONFIG_PM
of/address: sparc: Declare of_iomap as an extern function for sparc again
PM / QoS: fix wrong error-checking condition
bnx2x: remove redundant warning log
vxlan: fix command usage in its doc
8139cp: revert "set ring address before enabling receiver"
MPI: Fix compilation on MIPS with GCC 4.4 and newer
...
Conflicts:
drivers/gpu/drm/exynos/exynos_drm_encoder.c
drivers/gpu/drm/exynos/exynos_drm_fbdev.c
drivers/gpu/drm/nouveau/core/engine/disp/nv50.c
ASoC: Updates for v3.8
Some incremental updates, nothing too exciting. The biggest block here
is the __dev annotation removal stuff from Bill, everything else is the
usual driver-specific stuff - a combination of fixes and development.
There will be at least more more set of fixes to come but I wanted to
get these out ready for the merge window to make sure Bill's stuff makes
it in.
No-MMU architectures often have support for FDPIC binaries. FDPIC support
requires two additional fields in the mm_context_t struct. This patch adds these
fields to the generic mm_context_t definition if support for FDPIC binaries is
enabled. This allows to use the generic mmu.h for a few more architectures.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Nothing is using the vmlist field in mm_context_t anymore. It has been removed
from the non-generic versions over 3 years ago 8feae1311 ("NOMMU: Make VMAs per
MM as for MMU-mode linux").
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This patch adds the multiqueue (VIRTIO_NET_F_MQ) support to virtio_net
driver. VIRTIO_NET_F_MQ capable device could allow the driver to do packet
transmission and reception through multiple queue pairs and does the packet
steering to get better performance. By default, one one queue pair is used, user
could change the number of queue pairs by ethtool in the next patch.
When multiple queue pairs is used and the number of queue pairs is equal to the
number of vcpus. Driver does the following optimizations to implement per-cpu
virt queue pairs:
- select the txq based on the smp processor id.
- smp affinity hint to the cpu that owns the queue pairs.
This could be used with the flow steering support of the device to guarantee the
packets of a single flow is handled by the same cpu.
Signed-off-by: Krishna Kumar <krkumar2@in.ibm.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support in the kernel for offloading in the NIC Tx and Rx
checksumming for encapsulated packets (such as VXLAN and IP GRE).
For Tx encapsulation offload, the driver will need to set the right bits
in netdev->hw_enc_features. The protocol driver will have to set the
skb->encapsulation bit and populate the inner headers, so the NIC driver will
use those inner headers to calculate the csum in hardware.
For Rx encapsulation offload, the driver will need to set again the
skb->encapsulation flag and the skb->ip_csum to CHECKSUM_UNNECESSARY.
In that case the protocol driver should push the decapsulated packet up
to the stack, again with CHECKSUM_UNNECESSARY. In ether case, the protocol
driver should set the skb->encapsulation flag back to zero. Finally the
protocol driver should have NETIF_F_RXCSUM flag set in its features.
Signed-off-by: Joseph Gasparakis <joseph.gasparakis@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add requests to get the number of shader engines (SE) and
the number of SH per SE. These are needed for geometry
and tesselation shaders in the 3D driver as well as setting
up PA_SC_RASTER_CONFIG on SI asics.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
No version bump is required because setting the flag on older DRM has
no effect.
This only reserves the bit and doesn't use it. I assume we will use it
for buffer eviction heuristics.
Signed-off-by: Marek Olšák <maraeo@gmail.com>
commit 2e71a6f808 (net: gro: selective flush of packets) added
a bug for skbs using frag_list. This part of the GRO stack is rarely
used, as it needs skb not using a page fragment for their skb->head.
Most drivers do use a page fragment, but some of them use GFP_KERNEL
allocations for the initial fill of their RX ring buffer.
napi_gro_flush() overwrite skb->prev that was used for these skb to
point to the last skb in frag_list.
Fix this using a separate field in struct napi_gro_cb to point to the
last fragment.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If SYN-ACK partially acks SYN-data, the client retransmits the
remaining data by tcp_retransmit_skb(). This increments lost recovery
state variables like tp->retrans_out in Open state. If loss recovery
happens before the retransmission is acked, it triggers the WARN_ON
check in tcp_fastretrans_alert(). For example: the client sends
SYN-data, gets SYN-ACK acking only ISN, retransmits data, sends
another 4 data packets and get 3 dupacks.
Since the retransmission is not caused by network drop it should not
update the recovery state variables. Further the server may return a
smaller MSS than the cached MSS used for SYN-data, so the retranmission
needs a loop. Otherwise some data will not be retransmitted until timeout
or other loss recovery events.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
V5: fix two bugs pointed out by Thomas
remove seq check for now, mark it as TODO
V4: remove some useless #include
some coding style fix
V3: drop debugging printk's
update selinux perm table as well
V2: drop patch 1/2, export ifindex directly
Redesign netlink attributes
Improve netlink seq check
Handle IPv6 addr as well
This patch exports bridge multicast database via netlink
message type RTM_GETMDB. Similar to fdb, but currently bridge-specific.
We may need to support modify multicast database too (RTM_{ADD,DEL}MDB).
(Thanks to Thomas for patient reviews)
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Stephen Hemminger <shemminger@vyatta.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Thomas Graf <tgraf@suug.ch>
Cc: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Cong Wang <amwang@redhat.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
peer.transport_addr_list is currently only protected by sk_sock
which is inpractical to acquire for procfs dumping purposes.
This patch adds RCU protection allowing for the procfs readers to
enter RCU read-side critical sections.
Modification of the list continues to be serialized via sk_lock.
V2: Use list_del_rcu() in sctp_association_free() to be safe
Skip transports marked dead when dumping for procfs
Cc: Vlad Yasevich <vyasevich@gmail.com>
Cc: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* pci/bjorn-pcie-cap:
ath9k: Use standard #defines for PCIe Capability ASPM fields
iwlwifi: Use standard #defines for PCIe Capability ASPM fields
iwlwifi: collapse wrapper for pcie_capability_read_word()
iwlegacy: Use standard #defines for PCIe Capability ASPM fields
iwlegacy: collapse wrapper for pcie_capability_read_word()
cxgb3: Use standard #defines for PCIe Capability ASPM fields
PCI: Add standard PCIe Capability Link ASPM field names
PCI/portdrv: Use PCI Express Capability accessors
PCI: Use standard PCIe Capability Link register field names
PCI: Add and use standard PCI-X Capability register names
Some hosts need to perform additional actions upon card insertion or
ejection. Add a host operation to be called from card detection handlers.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Reviewed-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Add standard #defines for ASPM fields in PCI Express Link Capability and
Link Control registers.
Previously we used PCIE_LINK_STATE_L0S and PCIE_LINK_STATE_L1 directly, but
these are defined for the Linux ASPM interfaces, e.g.,
pci_disable_link_state(), and only coincidentally match the actual register
bits. PCIE_LINK_STATE_CLKPM, also part of that interface, does not match
the register bit.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Acked-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
A SMSC PHY in power down mode can't be used.
If a SMSC PHY is in this mode in the config_init
stage, the mode "all capable" is set. So the PHY
could then be used.
Signed-off-by: Philippe Reynes <tremyfr@yahoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Gabor Juhos