Merge branch 'for-davem' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next

John W. Linville says:

====================
This is a batch of updates intended for the 3.13 stream...

The biggest item of interest in here is wcn36xx, the new mac80211
driver for Qualcomm WCN3660/WCN3680 hardware.

Regarding the mac80211 bits, Johannes says:

"We have an assortment of cleanups and new features, of which the
biggest one is probably the channel-switch support in IBSS. Nothing
else really stands out much."

On top of that, the ath9k and rt2x00 get a lot of update action from
Felix Fietkau and Gabor Juhos, respectively.  There are a handful of
updates to other drivers here and there as well.

Please let me know if there are problems!
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

include/net/cfg80211.h

@@ -436,6 +436,15 @@ bool cfg80211_chandef_usable(struct wiphy *wiphy,
 			     const struct cfg80211_chan_def *chandef,
 			     u32 prohibited_flags);
 
+/**
+ * cfg80211_chandef_dfs_required - checks if radar detection is required
+ * @wiphy: the wiphy to validate against
+ * @chandef: the channel definition to check
+ * Return: 1 if radar detection is required, 0 if it is not, < 0 on error
+ */
+int cfg80211_chandef_dfs_required(struct wiphy *wiphy,
+				  const struct cfg80211_chan_def *chandef);
+
 /**
  * ieee80211_chandef_rate_flags - returns rate flags for a channel
  *

include/net/mac80211.h

@@ -829,6 +829,15 @@ ieee80211_tx_info_clear_status(struct ieee80211_tx_info *info)
  * @RX_FLAG_STBC_MASK: STBC 2 bit bitmask. 1 - Nss=1, 2 - Nss=2, 3 - Nss=3
  * @RX_FLAG_10MHZ: 10 MHz (half channel) was used
  * @RX_FLAG_5MHZ: 5 MHz (quarter channel) was used
+ * @RX_FLAG_AMSDU_MORE: Some drivers may prefer to report separate A-MSDU
+ *	subframes instead of a one huge frame for performance reasons.
+ *	All, but the last MSDU from an A-MSDU should have this flag set. E.g.
+ *	if an A-MSDU has 3 frames, the first 2 must have the flag set, while
+ *	the 3rd (last) one must not have this flag set. The flag is used to
+ *	deal with retransmission/duplication recovery properly since A-MSDU
+ *	subframes share the same sequence number. Reported subframes can be
+ *	either regular MSDU or singly A-MSDUs. Subframes must not be
+ *	interleaved with other frames.
  */
 enum mac80211_rx_flags {
 	RX_FLAG_MMIC_ERROR		= BIT(0),
@@ -859,6 +868,7 @@ enum mac80211_rx_flags {
 	RX_FLAG_STBC_MASK		= BIT(26) | BIT(27),
 	RX_FLAG_10MHZ			= BIT(28),
 	RX_FLAG_5MHZ			= BIT(29),
+	RX_FLAG_AMSDU_MORE		= BIT(30),
 };
 
 #define RX_FLAG_STBC_SHIFT		26
@@ -1492,6 +1502,11 @@ struct ieee80211_tx_control {
  *
  * @IEEE80211_HW_TIMING_BEACON_ONLY: Use sync timing from beacon frames
  *	only, to allow getting TBTT of a DTIM beacon.
+ *
+ * @IEEE80211_HW_CHANCTX_STA_CSA: Support 802.11h based channel-switch (CSA)
+ *	for a single active channel while using channel contexts. When support
+ *	is not enabled the default action is to disconnect when getting the
+ *	CSA frame.
  */
 enum ieee80211_hw_flags {
 	IEEE80211_HW_HAS_RATE_CONTROL			= 1<<0,
@@ -1522,6 +1537,7 @@ enum ieee80211_hw_flags {
 	IEEE80211_HW_P2P_DEV_ADDR_FOR_INTF		= 1<<25,
 	IEEE80211_HW_TIMING_BEACON_ONLY			= 1<<26,
 	IEEE80211_HW_SUPPORTS_HT_CCK_RATES		= 1<<27,
+	IEEE80211_HW_CHANCTX_STA_CSA			= 1<<28,
 };
 
 /**
@@ -2666,6 +2682,10 @@ enum ieee80211_roc_type {
  *	zero using ieee80211_csa_is_complete() after the beacon has been
  *	transmitted and then call ieee80211_csa_finish().
  *
+ * @join_ibss: Join an IBSS (on an IBSS interface); this is called after all
+ *	information in bss_conf is set up and the beacon can be retrieved. A
+ *	channel context is bound before this is called.
+ * @leave_ibss: Leave the IBSS again.
  */
 struct ieee80211_ops {
 	void (*tx)(struct ieee80211_hw *hw,
@@ -2857,6 +2877,9 @@ struct ieee80211_ops {
 	void (*channel_switch_beacon)(struct ieee80211_hw *hw,
 				      struct ieee80211_vif *vif,
 				      struct cfg80211_chan_def *chandef);
+
+	int (*join_ibss)(struct ieee80211_hw *hw, struct ieee80211_vif *vif);
+	void (*leave_ibss)(struct ieee80211_hw *hw, struct ieee80211_vif *vif);
 };
 
 /**
@@ -3919,6 +3942,25 @@ void ieee80211_iterate_active_interfaces_atomic(struct ieee80211_hw *hw,
 						    struct ieee80211_vif *vif),
 						void *data);
 
+/**
+ * ieee80211_iterate_active_interfaces_rtnl - iterate active interfaces
+ *
+ * This function iterates over the interfaces associated with a given
+ * hardware that are currently active and calls the callback for them.
+ * This version can only be used while holding the RTNL.
+ *
+ * @hw: the hardware struct of which the interfaces should be iterated over
+ * @iter_flags: iteration flags, see &enum ieee80211_interface_iteration_flags
+ * @iterator: the iterator function to call, cannot sleep
+ * @data: first argument of the iterator function
+ */
+void ieee80211_iterate_active_interfaces_rtnl(struct ieee80211_hw *hw,
+					      u32 iter_flags,
+					      void (*iterator)(void *data,
+						u8 *mac,
+						struct ieee80211_vif *vif),
+					      void *data);
+
 /**
  * ieee80211_queue_work - add work onto the mac80211 workqueue
  *