Bryan Brattlof <bb@ti.com> says:
Hello Everyone!
This small series converts TI's AM65x reference board to use
CONFIG_OF_UPSTREAM and removes the unused device tree files from
arch/arm/dts.
Because it's the last board using a AM65x without enabling OF_UPSTREAM
it allows us to also remove all the SoC FDT files as well and keep a
single version of the SoC's DT files in the dts/upstream directory going
forward.
Link: https://lore.kernel.org/r/20241121-am65x-v1-0-fe87aff1b5fc@ti.com
Rather than rely on manual updates from the arch/arm/dts directory,
enable CONFIG_OF_UPSTREAM to receive automatic device tree updates for
the am65x reference board.
Signed-off-by: Bryan Brattlof <bb@ti.com>
Aniket Limaye <a-limaye@ti.com> says:
This series adds OPP_LOW spec data in k3_avs driver and enables a config
option to select the OPP_LOW performance point.
J7200 SOC supports OPP_LOW and OPP_NOM as two Operating Performance
Points as per (7.5 Operating Performance Points) section in the
Datasheet [0].
- A72SS/MSMC at 2 GHz/1GHz operation must use OPP_NOM.
- A72SS/MSMC at 1 GHz/500 MHz operation can use OPP_NOM or OPP_LOW
voltage (though OPP_LOW voltage is recommended to reduce power
consumption).
The actual OPP voltage for the device is read from the efuse and
updated in k3_avs_probe().
The default j7200 devicetree and k3_avs driver set OPP_NOM spec
frequency and voltage.
In the board init file, if K3_OPP_LOW config is enabled, Check if
OPP_LOW AVS voltage read from efuse is valid and update frequency (A72
and MSMC) and voltage (VDD_CPU) as per the OPP_LOW spec.
[0]: https://www.ti.com/lit/gpn/dra821u (J7200 Datasheet)
Test logs:
https://gist.github.com/aniket-l/328ad93ed60c2419ed7be9f85e6b6075
- With series applied on master and CONFIG_K3_OPP_LOW enabled in
j7200_evm_r5_defconfig
- Logs shown with and without efuse register programmed for OPP_0
(Errors out if OPP_0 not found, programs OPP_LOW spec if found)
- Voltage update verified using 'i2c md 0x4c 0xe' in u-boot
- Frequency update verified using 'k3conf clock dump' in linux
Link: https://lore.kernel.org/r/20241119003617.1871183-1-a-limaye@ti.com
Define new CONFIG_K3_OPP_LOW under arm/mach-k3/r5/Kconfig and add
default value to j7200_evm_r5_defconfig
Signed-off-by: Reid Tonking <reidt@ti.com>
Signed-off-by: Aniket Limaye <a-limaye@ti.com>
Enable AVS support on J784S4 along with regulator.
Signed-off-by: Neha Malcom Francis <n-francis@ti.com>
Reviewed-by: Manorit Chawdhry <m-chawdhry@ti.com>
AMD/Xilinx changes for v2025.04-rc1
binman:
- Separate binman description from main DT
zynqmp:
- Enable binman for ZynqMP platforms
- DT sync with Linux v6.12
- Update usb5744 hub for SOMs
common:
- Drop SPL_FIT_GENERATOR support
versal2
- Enable OPTEE layers
ospi:
- Refactor the flash reset functionality
pytest:
- Fix tcminit mode handling
Add a small utility for displaying some information about U-Boot and the
hardware it's running on in a similar fashion to the popular neofetch
tool for Linux [1].
While the output is meant to be useful, it should also be pleasing to
look at and perhaps entertaining. The ufetch command aims to bring this
to U-Boot, featuring a colorful ASCII art version of the U-Boot logo.
[1]: https://en.wikipedia.org/wiki/Neofetch
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Tested-by: Mattijs Korpershoek <mkorpershoek@baylibre.com> # vim3
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8560-QRD
Acked-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Tested-by: Tony Dinh <mibodhi@gmail.com>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
There is necessary to do some steps to compose boot images. These steps
were in scripts in layers for a while. That's why introduce description via
binman to simplify wiring and remove all scripting around.
This should make sure that everybody is up2date with the latest versions.
The first step is to create fit image with DTBs with descriptions in
configuration node which is written as regular expression to match all SOM
versions.
Description is there for k24 and k26 in spite of low level psu_init
configuration is different. The reason is that it goes to u-boot.itb image
which is the same for k24 and k26.
u-boot.itb is another image which is generated. It is normally generated
via arch/arm/mach-zynqmp/mkimage_fit_atf.sh but this script is supposed to
be deprecated.
FIT image by purpose is using 64bit addresses to have default option to
move images to high DDR (above 4GB). TF-A and TEE are optional components
but in the most cases TF-A is present all the time and TEE(OP-TEE) is used
by some configurations too.
3rd generated image is boot.bin with updated user field which contains
version number. This image can be used with updated Image Selector
which supports A/B update mechanisms with rollback protection.
4th image is image.bin which binary file which contains boot.bin and
u-boot.itb together and can be programmed via origin Image Selector.
This image can be also used for creating one capsule which contains both
boot images (in SPL boot flow).
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/35bc47a4a4799c5f5dbea56a45340a2810538330.1730452668.git.michal.simek@amd.com
CI: https://source.denx.de/u-boot/custodians/u-boot-dfu/-/pipelines/23573
Android:
- bootstd: Implement bootimage v2 support
- bootstd: Support non-A/B in bootmeth_android
- Migrate VIM3 and VIM3L to use bootmeth_android
- bootstd: Additional test for bootimage v2
- bootstd: Optimize load time when reading partitions
The phyCORE-i.MX 93 is available in various variants (e.g. different ram
sizes, eMMC HS400 yes/no). Enable hardware introspection for the
imx93-phyboard-segin_defconfig, so that during startup the SOM module
variant can be detected, and the hardware can be configured accordingly.
The resulting SPL and u-boot binary shall able to boot each
phyCORE-i.MX 93 module variant on each carrier board. Finally rename
imx93-phyboard-segin_defconfig to imx93-phycore_defconfig, to highlight
its SOM scope.
Signed-off-by: Christoph Stoidner <c.stoidner@phytec.de>
Reviewed-by: Wadim Egorov <w.egorov@phytec.de>
Reviewed-by: Yannic Moog <y.moog@phytec.de>
make savedefconfig and add SCU_WDT and fix environment
offsets, as since silicon c0 the boot container takes place
at offset 0 and so the u-boot-env must be moved outside of
the boot container area.
Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Alexander Sverdlin <alexander.sverdlin@siemens.com>
We have many HW with capricorn i.MX8X boards. The difference in u-boot is
at all by the display of the LEDs.
* put upstream a reference project & board for DT and defconfig
* use the capricorn prefix outside the board/siemens/capricorn folder
Signed-off-by: Enrico Leto <enrico.leto@siemens.com>
Signed-off-by: Heiko Schocher <hs@denx.de>
Our MMC driver for JH7110 boards only supports reading to the low 4 GiB of
memory. Booting boards with more memory requires EFI_LOADER_BOUNCE_BUFFER.
Reported-by: E Shattow <lucent@gmail.com>
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Tested-by: Loic Devulder <ldevulder@suse.com>
CI: https://source.denx.de/u-boot/custodians/u-boot-snapdragon/-/pipelines/23474
- UFS support is enabled for SC7280 and SM8150 platforms.
- Qualcomm dt-bindings headers are all dropped in favour of
dts/upstream.
- The SMMU driver now correctly handles stream ID 0 and is disabled in
EL2.
- Initial support for capsule updates (using the new dynamic UUIDs) is
added for the RB3 Gen 2 board alongside a new SCSI backend for DFU.
- CONFIG_PINCONF is enabled in qcom_defconfig.
- The vqmmc supply is now enabled for sdcard support on boards that need
it.
- A quirk is added for reading GPIOs on the PM8550 PMIC
Enable all the necessary options for capsule updates to work, as well as
a few additional EFI features.
Capsule updates themselves are only enabled for the RB3 Gen 2, since the
exact details on where to flash U-Boot (or how to handle multiple boot
methods) has not been finalised for other boards.
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Now the Qualcomm controller and PHY drivers were accepted,
enable then in the qcom_defconfig file.
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Caleb Connolly <caleb.connolly@linaro.org>
The SM8550 and SM8650 SoCs requires PINCONF to properly
setup SDC pins in order to function correctly.
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Caleb Connolly <caleb.connolly@linaro.org>
Wadim Egorov <w.egorov@phytec.de> says:
Our SoMs are available in multiple configurations, managed via device
tree overlays. To determine the specific variant in use, we read the
EEPROM and apply the appropriate overlays during boot to the device tree
used by the OS.
Apply overlays for phyCORE-AM62x and phyCORE-AM64x SoMs.
Future K3 SoMs will be able to reuse this logic and overlays.
Link: https://lore.kernel.org/r/20241030164815.1763506-1-w.egorov@phytec.de
Include SoM dt-overlays for DT control so we can include them
into our u-boot FIT image.
While at it also resync after savedefconfig.
Signed-off-by: Wadim Egorov <w.egorov@phytec.de>
Sometimes this breaks, so add a build to keep it working. Since sandbox
enables a lot of options, it is a good board to use. The new config is
created simply by copying the existing sandbox and turning off CMDLINE
Once we have tests for non-CMDLINE operation, this can be adjusted to
run those tests.
Create a new build which will be picked up by CI. Update the maintainer
entry as well.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Heinrich Schuchardt <heinrich.schuchardt@canonical.com> says:
The lib_test_uuid_to_le and lib lib_test_dynamic_uuid tests fail on
32-bit systems. But we never caught this in our CI because we never
ran any of our C unit tests on 32-bit.
Enable CONFIG_UNIT_TEST on qemu_arm_defconfig.
hextoul() cannot convert a string to a 64-bit number on a 32-bit system.
Use the new function hextoull() instead.
Link: https://lore.kernel.org/r/20241103224223.195255-1-heinrich.schuchardt@canonical.com
The lib_test_uuid_to_le test fails on 32-bit systems. But we never caught
this in our CI because we never ran any of our C unit tests on 32-bit.
Enable CONFIG_UNIT_TEST on qemu_arm_defconfig.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
QEMU already has an lwip variant of a defconfig. That defconfig
is also configured with mbedTLS by default. So let's enable the
remaining config options to enable wget for https:// as well
and test that codepath in the CI
Reviewed-by: Jerome Forissier <jerome.forissier@linaro.org>
Reviewed-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Add manufacturing environment into STM32MP15xx DH electronics DHSOM
configuration. This environment is part of every board build, but only
takes effect on systems booted with the dh,stm32mp15xx-dhcor-testbench
device tree, i.e. systems populated with factory build of U-Boot.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Deduplicate defconfigs for all DH STM32MP1xx DHSOM systems by factoring
out the common parts into generic stm32mp_dhsom.config and including
those using the #include <configs/...> preprocessor macro in the current
set of board specific defconfigs. The preprocessor macro is applicable
to defconfigs as well.
This introduces no functional change, the resulting .config is identical
for all DH STM32MP1xx DHSOM systems.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Deduplicate defconfigs for all DH STM32MP15xx DHSOM systems by factoring
out the common parts into generic stm32mp15_dhsom.config and including
those using the #include <configs/...> preprocessor macro in the current
set of board specific defconfigs. The preprocessor macro is applicable
to defconfigs as well.
This introduces no functional change, the resulting .config is identical
for all DH STM32MP15xx DHSOM systems.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Use RTC available in HW on Kria SOM without using emulation that's why
configure it properly and disable emulated one.
Power on reset value of RTC Calibration register without battery backup is
not matching with crystal frequency which leads to RTC time drift. That's
why write CALIB_WRITE register with crystal frequency (0x7FFF). There is
also an option to write zero so that Linux will set default value (0x7FFF)
in driver probe but calibration 0 is not permited by DT schema.
Co-developed-by: Srinivas Goud <srinivas.goud@amd.com>
Signed-off-by: Srinivas Goud <srinivas.goud@amd.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/9b684faeec85381b9b8fe796aaebc2ee79f17b8e.1729663761.git.michal.simek@amd.com
