This is done by introducing drbd_nla_find_nested() which handles the flag
before calling nla_find_nested().
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Make it more clear in the flag names which flags are internal to drbd, and
which are not.
The check for mandatory attributes is the only extension visible at the netlink
layer. Attributes with this flag set would look like unknown attributes to
some kernel versions. The netlink layer would ignore them and also skip
consistency checks on the attribute type and legth. To avoid this, we check
for mandatory attributes first, remove the mandatory flag, and then process the
attributes normally.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Note: All input values are still treated as signed; unsigned long long values
are still broken.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
* the peer does not speak protocol_version 100 and the
user wants to change one of:
- wire_protocol
- two_primaries
- integrity_alg
* the user wants to remove the allow_two_primaries flag
when there are two primaries
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
The 32-bit resync_after netlink field takes a device minor number as
parameter, which is no longer limited to 255. We cannot statically
verify which device numbers are valid, so set the ummer limit to the
highest possible signed 32-bit integer.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Change the --no-tcp-cork drbdsetup command line option as well as
the no_cork netlink packet.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Change the --no-md-flushes drbdsetup command line option as well as
the no_md_flush netlink packet.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Change the --no-disk-drain drbdsetup command line option as well as
the no_disk_drain netlink packet.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Change the --no-disk-flushes drbdsetup command line option as well as
the no_disk_flush netlink packet.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Flags of type NLA_FLAG are either present or absent, but do not have a
value by themselves. Use type NLA_U8 for our boolean flags instead, and
use the value to determine if the flag should be on or off.
On the drbdsetup command line, all those flags have an optional yes/no
argument which defaults to yes.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
The 8 byte header finally becomes too small. With the protocol 100 header we
have 16 bit for the volume number, proper 32 bit for the data length, and
32 bit for further extensions in the future.
Previous versions of drbd are using version 80 headers for all packets
short enough for protocol 80. They support both header versions in
worker context, but only version 80 headers in asynchronous context.
For backwards compatibility, continue to use version 80 headers for
short packets before protocol version 100.
From protocol version 100 on, use the same header version for all
packets.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
This commit breaks the API again.
Move per-volume former syncer options into disk_conf.
Move per-connection former syncer options into net_conf.
Renamed the remainign sync_conf to res_opts
Syncer settings have been changeable at runtime, so we need to prepare
for these settings to be runtime-changeable in their new home as well.
Introduce new configuration operations, and share the netlink attribute
between "attach" (create new disk) and "disk-opts" (change options).
Same for "connect" and "net-opts".
Some fields cannot be changed at runtime, however.
Introduce a new flag GENLA_F_INVARIANT to be able to trigger on that in
the generated validation and assignment functions.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
This commit adds FILEID_INVALID = 0xff in fid_type to
indicate invalid fid_type
It avoids using magic number 255
Signed-off-by: Namjae Jeon <linkinjeon@gmail.com>
Signed-off-by: Vivek Trivedi <vtrivedi018@gmail.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
The of_device_id match data is now marked as const and
must not be modified. This changes the dw_mmc to mark
all pointers passing the dw_mci_drv_data or dw_mci_dma_ops
structures as const, and also marks the static definitions
as const.
drivers/mmc/host/dw_mmc-exynos.c: In function 'dw_mci_exynos_probe':
drivers/mmc/host/dw_mmc-exynos.c:234:11: warning: assignment discards 'const' qualifier from pointer target type [enabled by default]
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Thomas Abraham <thomas.abraham@linaro.org>
Cc: Will Newton <will.newton@imgtec.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
CMD23 causes lots of errors in kernel on some freescale SoCs
(P1020, P1021, P1022, P1024, P1025 and P4080) when MMC card used,
which is because these controllers does not support CMD23,
even on the SoCs which declares CMD23 is supported.
Therefore, we'll not use CMD23.
Signed-off-by: Jerry Huang <Chang-Ming.Huang@freescale.com>
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Acked-by: Anton Vorontsov <cbouatmailru@gmail.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Even though platform_get_irq returns error, 'host->irq'
always has an unsigned value. Less-than-zero comparison
of an unsigned value is never true. Type of 'unsigned int'
will be changed for 'int'.
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Acked-by: Will Newton <will.newton@imgtec.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
ocp2scp was not having pdata support which makes *musb* fail for non-dt
boot in OMAP platform. The pdata will have information about the devices
that is connected to ocp2scp. ocp2scp driver will now make use of this
information to create the devices that is attached to ocp2scp.
This is needed to fix MUSB regression caused by commit c9e4412a
(arm: omap: phy: remove unused functions from omap-phy-internal.c)
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
[tony@atomide.com: updated comments for regression info]
Signed-off-by: Tony Lindgren <tony@atomide.com>
pci_ext_cfg_avail() doesn't use the "struct pci_dev *" passed to
it, and there's no requirement that a host bridge even be represented
by a pci_dev. This drops the pci_ext_cfg_avail() parameter.
[bhelgaas: changelog]
Signed-off-by: Taku Izumi <izumi.taku@jp.fujitsu.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
This patch introduces the below two helpers to prepare for solving
the usbnet runtime PM problem, which may cause some network utilities
(ifconfig, ethtool,...) touch a suspended device.
usbnet_read_cmd_nopm()
usbnet_write_cmd_nopm()
The above two helpers should be called by usbnet resume/suspend
callback to avoid deadlock.
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
From Michal Simek:
* 'arm-next' of git://git.xilinx.com/linux-xlnx:
zynq: move static peripheral mappings
zynq: remove use of CLKDEV_LOOKUP
zynq: use pl310 device tree bindings
zynq: use GIC device tree bindings
+ Linux 3.7-rc3
From Linus Walleij:
This patchset will:
- Move all remaining headers out of arch/arm/plat-nomadik/include/plat
out to e.g. include/linux/platform_data
- Delete arch/arm/plat-nomadik
- Convert Nomadik and Ux500 to SPARSE_IRQ
* tag 'kill-plat-sparse-irq' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
ARM: plat-nomadik: convert platforms to SPARSE_IRQ
mfd/db8500-prcmu: use the irq_domain_add_simple()
mfd/ab8500-core: use irq_domain_add_simple()
ARM: plat-nomadik: move MTU, kill plat-nomadik
ARM: plat-nomadik: move DMA40 header to <linux/platform_data>
ARM: plat-nomadik: use DIV_ROUND_CLOSEST()
ARM: plat-nomadik: pass IRQ to timer driver
clk/ux500: explicitly include register header
pinctrl/nomadik: merge old pincfg header
pinctrl/nomadik: move the platform data header
ARM: plat-nomadik: move NMK_GPIO_PER_CHIP into gpio-nomadik.h
ARM: plat-nomadik: Introduce new DB8540 GPIO registers
From Linus Walleij:
This provides the following Integrator refactorings:
- Switch the FPGA IRQ controller to use the simple IRQ domain
- Get rid of preallocated IRQ descriptors on the Integrator
- Move the FPGA IRQ driver to drivers/irqchip
* tag 'integrator-irq' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-integrator:
ARM: plat-versatile: move FPGA irq driver to drivers/irqchip
ARM: integrator: get rid of preallocated irq descriptors
ARM: plat-versatile: use simple irqdomain for FPGA IRQ
Add platform device id to check whether the SSC controller support
pdc or dam for data transfer
If match "at91rm9200_ssc", which support pdc for data transfer
If match "at91sam9g45_ssc", which support dma for data transfer
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch adds support for TI's ADC driver.
This is a multifunctional device.
Analog input lines are provided on which
voltage measurements can be carried out.
You can have upto 8 input lines.
Signed-off-by: Patil, Rachna <rachna@ti.com>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This patch converts touchscreen into a MFD client.
All the register definitions, clock initialization,
etc has been moved to MFD core driver.
Signed-off-by: Patil, Rachna <rachna@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Add the mfd core driver which supports touchscreen
and ADC.
With this patch we are only adding infrastructure to
support the MFD clients.
Signed-off-by: Patil, Rachna <rachna@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Make way for addition of MFD driver.
The existing touchsreen driver is a MFD client.
For better readability we rename the file to
indicate its functionality as only touchscreen.
Signed-off-by: Patil, Rachna <rachna@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
