Move the workaround for double sending AUDIO_CODEC and AUDIO_DAC writes
into the SPI core, aiding refactoring to eliminate the ASoC custom I/O
functions and avoiding the extra writes for I2C.
Signed-off-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The ADC clock divider needs to be restored on resume as the register content
is lost when the ADC is powered down
Signed-off-by: Matthias Kaehlcke <matthias@kaehlcke.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This adds a driver for the STw481x PMICs found in the Nomadik
family of platforms. This one uses pure device tree probing.
Print some of the OTP registers on boot and register a regulator
MFD child.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
We had specified the mask twice for FLL2_SYNC_BW change the first mask
definition in a bit definition to match the other fields.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
In some platforms, specially Thinkpad series, rts5249 won't be
initialized properly. So we need adjust some phy parameters to
improve the compatibility issue.
It is a little different between simulation and real chip. We have
no idea about which configuration is better before tape-out. We set
default settings according to simulation, but need to tune these
parameters after getting the real chip.
I can't explain every change in detail here. The below information is
just a rough description:
PHY_REG_REV: Disable internal clkreq_tx, enable rx_pwst
PHY_BPCR: No change, just turn the magic number to macro definitions
PHY_PCR: Change OOBS sensitivity, from 60mV to 90mV
PHY_RCR2: Control charge-pump current automatically
PHY_FLD4: Use TX cmu reference clock
PHY_RDR: Change RXDSEL from 30nF to 1.9nF
PHY_RCR1: Change the duration between adp_st and asserting cp_en from
0.32 us to 0.64us
PHY_FLD3: Adjust internal timers
PHY_TUNE: Fine tune the regulator12 output voltage
Signed-off-by: Wei WANG <wei_wang@realsil.com.cn>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The old timeout value was based on the assumption that the minimum values are
used for the open and sample delay and no averaging is done. In fact the ADC
and touchscreen driver both use an open delay of 152 cycles and averaging over
16 samples. This patch adjusts the timeout value accordingly
Signed-off-by: Matthias Kaehlcke <matthias@kaehlcke.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Since the conversion to regmap-irq irq_lock has been unused.
Signed-off-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Since the register I/O functions are all simple wrappers for the regmap
equivalents inline them to provide a small code size saving and an example
of good practice.
Signed-off-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
DA9053 (up to revision bc) can corrupt internal registers when multi-write
mode is enabled and power is removed or during shutdown.
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Occasionally, it is useful to map supplies from a child device onto the
MFD device. A typical usecase for this would be if the MFD device is
represented as a single node in device tree. All supplies will be
defined in device tree as existing on the MFD device. When a child
depends on frameworks which might have no knowledge of MFD to lookup
supplies on its behalf the supply will not be found.
This patch adds a list of supplies that should be looked up on the
parent rather than the child as part of the mfd_cell structure.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
Pull networking fixes from David Miller:
"Sorry I let so much accumulate, I was in Buffalo and wanted a few
things to cook in my tree for a while before sending to you. Anyways,
it's a lot of little things as usual at this stage in the game"
1) Make bonding MAINTAINERS entry reflect reality, from Andy
Gospodarek.
2) Fix accidental sock_put() on timewait mini sockets, from Eric
Dumazet.
3) Fix crashes in l2tp due to mis-handling of ipv4 mapped ipv6
addresses, from François CACHEREUL.
4) Fix heap overflow in __audit_sockaddr(), from the eagle eyed Dan
Carpenter.
5) tcp_shifted_skb() doesn't take handle FINs properly, from Eric
Dumazet.
6) SFC driver bug fixes from Ben Hutchings.
7) Fix TX packet scheduling wedge after channel change in ath9k driver,
from Felix Fietkau.
8) Fix user after free in BPF JIT code, from Alexei Starovoitov.
9) Source address selection test is reversed in
__ip_route_output_key(), fix from Jiri Benc.
10) VLAN and CAN layer mis-size netlink attributes, from Marc
Kleine-Budde.
11) Fix permission checks in sysctls to use current_euid() instead of
current_uid(). From Eric W Biederman.
12) IPSEC policies can go away while a timer is still pending for them,
add appropriate ref-counting to fix, from Steffen Klassert.
13) Fix mis-programming of FDR and RMCR registers on R8A7740 sh_eth
chips, from Nguyen Hong Ky and Simon Horman.
14) MLX4 forgets to DMA unmap pages on RX, fix from Amir Vadai.
15) IPV6 GRE tunnel MTU upper limit is miscalculated, from Oussama
Ghorbel.
16) Fix typo in fq_change(), we were assigning "initial quantum" to
"quantum". From Eric Dumazet.
17) Set a more appropriate sk_pacing_rate for non-TCP sockets, otherwise
FQ packet scheduler does not pace those flows properly. Also from
Eric Dumazet.
18) rtlwifi miscalculates packet pointers, from Mark Cave-Ayland.
19) l2tp_xmit_skb() can be called from process context, not just softirq
context, so we must always make sure to BH disable around it. From
Eric Dumazet.
20) On qdisc reset, we forget to purge the RB tree of SKBs in netem
packet scheduler. From Stephen Hemminger.
21) Fix info leak in farsync WAN driver ioctl() handler, from Dan
Carpenter and Salva Peiró.
22) Fix PHY reset and other issues in dm9000 driver, from Nikita
Kiryanov and Michael Abbott.
23) When hardware can do SCTP crc32 checksums, we accidently don't
disable the csum offload when IPSEC transformations have been
applied. From Fan Du and Vlad Yasevich.
24) Tail loss probing in TCP leaves the socket in the wrong congestion
avoidance state. From Yuchung Cheng.
25) In CPSW driver, enable NAPI before interrupts are turned on, from
Markus Pargmann.
26) Integer underflow and dual-assignment in YAM hamradio driver, from
Dan Carpenter.
27) If we are going to mangle a packet in tcp_set_skb_tso_segs() we must
unclone it. This fixes various hard to track down crashes in
drivers where the SKBs ->gso_segs was changing right from underneath
the driver during TX queueing. From Eric Dumazet.
28) Fix the handling of VLAN IDs, and in particular the special IDs 0
and 4095, in the bridging layer. From Toshiaki Makita.
29) Another info leak, this time in wanxl WAN driver, from Salva Peiró.
30) Fix race in socket credential passing, from Daniel Borkmann.
31) WHen NETLABEL is disabled, we don't validate CIPSO packets properly,
from Seif Mazareeb.
32) Fix identification of fragmented frames in ipv4/ipv6 UDP
Fragmentation Offload output paths, from Jiri Pirko.
33) Virtual Function fixes in bnx2x driver from Yuval Mintz and Ariel
Elior.
34) When we removed the explicit neighbour pointer from ipv6 routes a
slight regression was introduced for users such as IPVS, xt_TEE, and
raw sockets. We mix up the users requested destination address with
the routes assigned nexthop/gateway. From Julian Anastasov and
Simon Horman.
35) Fix stack overruns in rt6_probe(), the issue is that can end up
doing two full packet xmit paths at the same time when emitting
neighbour discovery messages. From Hannes Frederic Sowa.
36) davinci_emac driver doesn't handle IFF_ALLMULTI correctly, from
Mariusz Ceier.
37) Make sure to set TCP sk_pacing_rate after the first legitimate RTT
sample, from Neal Cardwell.
38) Wrong netlink attribute passed to xfrm_replay_verify_len(), from
Steffen Klassert.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (152 commits)
ax88179_178a: Add VID:DID for Samsung USB Ethernet Adapter
ax88179_178a: Correct the RX error definition in RX header
Revert "bridge: only expire the mdb entry when query is received"
tcp: initialize passive-side sk_pacing_rate after 3WHS
davinci_emac.c: Fix IFF_ALLMULTI setup
mac802154: correct a typo in ieee802154_alloc_device() prototype
ipv6: probe routes asynchronous in rt6_probe
netfilter: nf_conntrack: fix rt6i_gateway checks for H.323 helper
ipv6: fill rt6i_gateway with nexthop address
ipv6: always prefer rt6i_gateway if present
bnx2x: Set NETIF_F_HIGHDMA unconditionally
bnx2x: Don't pretend during register dump
bnx2x: Lock DMAE when used by statistic flow
bnx2x: Prevent null pointer dereference on error flow
bnx2x: Fix config when SR-IOV and iSCSI are enabled
bnx2x: Fix Coalescing configuration
bnx2x: Unlock VF-PF channel on MAC/VLAN config error
bnx2x: Prevent an illegal pointer dereference during panic
bnx2x: Fix Maximum CoS estimation for VFs
drivers: net: cpsw: fix kernel warn during iperf test with interrupt pacing
...
The NXP PCA9685 supports 16 channels/leds using a 12-bit PWM (4095
levels of brightness)
This driver supports configuration using platform_data.
Signed-off-by: Maximilian Güntner <maximilian.guentner@gmail.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
This enables setting a default trigger on an LP55xx channel,
either from platform data or device tree. This mechanism is
identical to the mechanism for GPIO LEDs and references the
common LEDs device tree bindings.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Milo Kim <milo.kim@ti.com>
Acked-by: Milo Kim <milo.kim@ti.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
Extract DMA channels directly from DT as they can not be found from
platform resources anymore. This is a work-around until davinci audio
driver is updated to use dmaengine.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Instead of cb->data, use callback dump args only and introduce symbolic
names instead of plain numbers at accessing the argument members.
Signed-off-by: Jozsef Kadlecsik <kadlec@blackhole.kfki.hu>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Now ipv6_gso_segment() is stackable, its relatively easy to
implement GSO/TSO support for SIT tunnels
Performance results, when segmentation is done after tunnel
device (as no NIC is yet enabled for TSO SIT support) :
Before patch :
lpq84:~# ./netperf -H 2002:af6:1153:: -Cc
MIGRATED TCP STREAM TEST from ::0 (::) port 0 AF_INET6 to 2002:af6:1153:: () port 0 AF_INET6
Recv Send Send Utilization Service Demand
Socket Socket Message Elapsed Send Recv Send Recv
Size Size Size Time Throughput local remote local remote
bytes bytes bytes secs. 10^6bits/s % S % S us/KB us/KB
87380 16384 16384 10.00 3168.31 4.81 4.64 2.988 2.877
After patch :
lpq84:~# ./netperf -H 2002:af6:1153:: -Cc
MIGRATED TCP STREAM TEST from ::0 (::) port 0 AF_INET6 to 2002:af6:1153:: () port 0 AF_INET6
Recv Send Send Utilization Service Demand
Socket Socket Message Elapsed Send Recv Send Recv
Size Size Size Time Throughput local remote local remote
bytes bytes bytes secs. 10^6bits/s % S % S us/KB us/KB
87380 16384 16384 10.00 5525.00 7.76 5.17 2.763 1.840
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We have a lot of confusing names of functions and data structures in
amongs the the error reporting code. In particular the "apei" prefix
has been applied to many objects that are not part of APEI. Since we
will be using these routines for extended error log reporting it will
be clearer if we fix up the names first.
Signed-off-by: Chen, Gong <gong.chen@linux.intel.com>
Acked-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
This patch fixes the following warning:
In file included from include/linux/skbuff.h:27:0,
from include/linux/netfilter.h:5,
from include/net/netns/netfilter.h:5,
from include/net/net_namespace.h:20,
from include/linux/init_task.h:14,
from init/init_task.c:1:
include/linux/net.h:243:14: warning: 'struct static_key' declared inside parameter list [enabled by default]
struct static_key *done_key);
on x86_64 allnoconfig, um defconfig and ia64 allmodconfig and maybe others as well.
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The DLL(Delay Line) is newly added to assist in sampling read data.
The DLL provides the ability to programmatically select a quantized
delay (in fractions of the clock period) regardless of on-chip variations
such as process, voltage and temperature (PVT).
This patch adds a user interface to set slave delay line via device tree.
It's usually used in high speed mode like mmc DDR mode when the signal
quality is not good caused by board design, e.g. the signal path is too
long. User can manually set delay line to find a suitable data sampling
window for card to work properly.
Signed-off-by: Dong Aisheng <b29396@freescale.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Add imx6sl iomux-gpr register field define in "imx6q-iomuxc-gpr.h" header
file, which is not fully define all iomux-gpr registers and fields, only
add fec related macro define.
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
s3c2410 and s3c2442 share the same dma channels while s3c2440 has
slight differences. But on all three the reachable sources per dma
channel has constraints attached and thus encodes the usable
combinations using the S3C24XX_DMA_CHANREQ macro.
This also fixes the warning about s3c2410_dma_resource being unused
as reported by Olof Johansson.
Reported-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
net_get_random_once is a new macro which handles the initialization
of secret keys. It is possible to call it in the fast path. Only the
initialization depends on the spinlock and is rather slow. Otherwise
it should get used just before the key is used to delay the entropy
extration as late as possible to get better randomness. It returns true
if the key got initialized.
The usage of static_keys for net_get_random_once is a bit uncommon so
it needs some further explanation why this actually works:
=== In the simple non-HAVE_JUMP_LABEL case we actually have ===
no constrains to use static_key_(true|false) on keys initialized with
STATIC_KEY_INIT_(FALSE|TRUE). So this path just expands in favor of
the likely case that the initialization is already done. The key is
initialized like this:
___done_key = { .enabled = ATOMIC_INIT(0) }
The check
if (!static_key_true(&___done_key)) \
expands into (pseudo code)
if (!likely(___done_key > 0))
, so we take the fast path as soon as ___done_key is increased from the
helper function.
=== If HAVE_JUMP_LABELs are available this depends ===
on patching of jumps into the prepared NOPs, which is done in
jump_label_init at boot-up time (from start_kernel). It is forbidden
and dangerous to use net_get_random_once in functions which are called
before that!
At compilation time NOPs are generated at the call sites of
net_get_random_once. E.g. net/ipv6/inet6_hashtable.c:inet6_ehashfn (we
need to call net_get_random_once two times in inet6_ehashfn, so two NOPs):
71: 0f 1f 44 00 00 nopl 0x0(%rax,%rax,1)
76: 0f 1f 44 00 00 nopl 0x0(%rax,%rax,1)
Both will be patched to the actual jumps to the end of the function to
call __net_get_random_once at boot time as explained above.
arch_static_branch is optimized and inlined for false as return value and
actually also returns false in case the NOP is placed in the instruction
stream. So in the fast case we get a "return false". But because we
initialize ___done_key with (enabled != (entries & 1)) this call-site
will get patched up at boot thus returning true. The final check looks
like this:
if (!static_key_true(&___done_key)) \
___ret = __net_get_random_once(buf, \
expands to
if (!!static_key_false(&___done_key)) \
___ret = __net_get_random_once(buf, \
So we get true at boot time and as soon as static_key_slow_inc is called
on the key it will invert the logic and return false for the fast path.
static_key_slow_inc will change the branch because it got initialized
with .enabled == 0. After static_key_slow_inc is called on the key the
branch is replaced with a nop again.
=== Misc: ===
The helper defers the increment into a workqueue so we don't
have problems calling this code from atomic sections. A seperate boolean
(___done) guards the case where we enter net_get_random_once again before
the increment happend.
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Jason Baron <jbaron@redhat.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Eric Dumazet <edumazet@google.com>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Usage of the static key primitives to toggle a branch must not be used
before jump_label_init() is called from init/main.c. jump_label_init
reorganizes and wires up the jump_entries so usage before that could
have unforeseen consequences.
Following primitives are now checked for correct use:
* static_key_slow_inc
* static_key_slow_dec
* static_key_slow_dec_deferred
* jump_label_rate_limit
The x86 architecture already checks this by testing if the default_nop
was already replaced with an optimal nop or with a branch instruction. It
will panic then. Other architectures don't check for this.
Because we need to relax this check for the x86 arch to allow code to
transition from default_nop to the enabled state and other architectures
did not check for this at all this patch introduces checking on the
static_key primitives in a non-arch dependent manner.
All checked functions are considered slow-path so the additional check
does no harm to performance.
The warnings are best observed with earlyprintk.
Based on a patch from Andi Kleen.
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Andi Kleen <andi@firstfloor.org>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now inet_gso_segment() is stackable, its relatively easy to
implement GSO/TSO support for IPIP
Performance results, when segmentation is done after tunnel
device (as no NIC is yet enabled for TSO IPIP support) :
Before patch :
lpq83:~# ./netperf -H 7.7.9.84 -Cc
MIGRATED TCP STREAM TEST from 0.0.0.0 (0.0.0.0) port 0 AF_INET to 7.7.9.84 () port 0 AF_INET
Recv Send Send Utilization Service Demand
Socket Socket Message Elapsed Send Recv Send Recv
Size Size Size Time Throughput local remote local remote
bytes bytes bytes secs. 10^6bits/s % S % S us/KB us/KB
87380 16384 16384 10.00 3357.88 5.09 3.70 2.983 2.167
After patch :
lpq83:~# ./netperf -H 7.7.9.84 -Cc
MIGRATED TCP STREAM TEST from 0.0.0.0 (0.0.0.0) port 0 AF_INET to 7.7.9.84 () port 0 AF_INET
Recv Send Send Utilization Service Demand
Socket Socket Message Elapsed Send Recv Send Recv
Size Size Size Time Throughput local remote local remote
bytes bytes bytes secs. 10^6bits/s % S % S us/KB us/KB
87380 16384 16384 10.00 7710.19 4.52 6.62 1.152 1.687
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to support GSO on IPIP, we need to make
inet_gso_segment() stackable.
It should not assume network header starts right after mac
header.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ACPI GpioInt resources contain polarity field that is used to specify
whether the interrupt is active high or low. Since gpiolib supports
GPIOF_ACTIVE_LOW we can pass this information in the flags field in
acpi_find_gpio(), analogous to the DeviceTree version.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The new GPIO descriptor based interface is now preferred over the old
integer based one. This patch converts the ACPI GPIO helpers to use this
new interface internally. In addition to that provide compatibility
function acpi_get_gpio_by_index() that converts the returned GPIO
descriptor to an integer.
We also drop acpi_get_gpio() as it is not used anywhere outside
gpiolib-acpi and even there we use acpi_get_gpiod() instead.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add gpiod_get(), gpiod_get_index() and gpiod_put() functions that
provide safer management of GPIOs.
These functions put the GPIO framework in line with the conventions of
other frameworks in the kernel, and help ensure every GPIO is declared
properly and valid while it is used.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Refactor the of_ functions of gpiolib to use the now public gpiod
interface, and export of_get_named_gpiod_flags() and
of_get_gpiod_flags() functions.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch exports the gpiod_* family of API functions, a safer
alternative to the legacy GPIO interface. Differences between the gpiod
and legacy gpio APIs are:
- gpio works with integers, whereas gpiod operates on opaque handlers
which cannot be forged or used before proper acquisition
- gpiod get/set functions are aware of the active low state of a GPIO
- gpio consumers should now include <linux/gpio/consumer.h> to access
the new interface, whereas chips drivers will use
<linux/gpio/driver.h>
The legacy gpio API is now built as inline functions on top of gpiod.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Sarah writes:
xhci: Final patches for 3.13
Hi Greg,
Here's my pull request for usb-next and 3.13. My xHCI tree is closed
after this point, since I won't be able to run my full tests while I'm in
Scotland. After Kernel Summit, I'll be on vacation with access to email
from Oct 26th to Nov 6th.
Here's what's in this request:
- Patches to fix USB 2.0 Link PM issues that cause USB 3.0 devices to not
enumerate or misbehave when plugged into a USB 2.0 port. Those are
marked for stable.
- A msec vs jiffies bug fix by xiao jin, which results in fairly harmless
behavior, and thus isn't marked for stable.
- Xenia's patches to refactor the xHCI command handling code, which makes
it much more readable and consistent.
- Misc cleanup patches, one by Sachin Kamat and three from Dan Williams.
Here's what's not in this request:
- Dan's two patches to allow the xHCI host to use the "Windows" or "new"
enumeration scheme. I did not have time to test those, and I want to
run them with as many USB devices as I can get a hold of. That will
have to wait for 3.14.
- Xenia's patches to remove xhci_readl in favor of readl. I'll queue
those for 3.14 after I test them.
- The xHCI streams update, UAS fixes, and usbfs streams support. I'm not
comfortable with changes and fixes to that patchset coming in this late.
I would rather wait for 3.14 and be really sure the streams support is
stable before we add new userspace API and remove CONFIG_BROKEN from the
uas driver.
- Julius' patch to clear the port reset bit on hub resume that came in
a couple days ago. It looks harmless, but I would rather take the time
to test and queue it for usb-linus and the stable trees once 3.13-rc1
is out.
Sarah Sharp
Do not overwrite the multi-byte fields of usb_wa_descriptor with their
cpu format values after reading the descriptor. Leave the values as
__le16 and swap on use. This is more consistent with other uses of USB
descriptors.
Signed-off-by: Thomas Pugliese <thomas.pugliese@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Extend the list of power gates found on Tegra114. Note that there are
now holes in the list, so perhaps a simple array is no longer the best
data structure to represent it.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
From Tony Lindgren:
Changes needed to drop legacy booting support for some
omap3 boards.
Note that that these are based on a merge of the
following for the dependencies:
- v3.12-rc5 for fixes to pinctrl mask
- omap-for-v3.13/dt-signed to avoid pointless merge conflicts
- omap-for-v3.13/quirk-signed for legacy pdata handling
* tag 'omap-for-v3.13/board-removal-signed-take2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (125 commits)
ARM: OMAP2+: remove legacy support for IGEP boards
ARM: OMAP2+: Remove legacy support for zoom platforms
ARM: OMAP2+: Remove legacy booting support for omap3 EVM
ARM: OMAP2: delete board-rm680
ARM: dts: add minimal DT support for Nokia N950 & N9 phones
ARM: dts: Add basic support for zoom3
ARM: dts: Add basic support for TMDSEVM3730 (Mistral AM/DM37x EVM)
ARM: dts: Add common support for omap3-evm
ARM: dts: Shared file for omap GPMC connected smsc911x
+Linux 3.12-rc5
Signed-off-by: Kevin Hilman <khilman@linaro.org>
Macro definitions should not normally end with a semi-colon, as this
makes it dangerous to use them an if...else statement. Happily this
has not happened yet.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While working on virtio_net new allocation strategy to increase
payload/truesize ratio, we found that refactoring sk_page_frag_refill()
was needed.
This patch splits sk_page_frag_refill() into two parts, adding
skb_page_frag_refill() which can be used without a socket.
While we are at it, add a minimum frag size of 32 for
sk_page_frag_refill()
Michael will either use netdev_alloc_frag() from softirq context,
or skb_page_frag_refill() from process context in refill_work()
(GFP_KERNEL allocations)
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Michael Dalton <mwdalton@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These patches add the ability to create an alternative device on which
a lookup for a certain supply should be conducted.
A common use-case for this would be devices that are logically
represented as a collection of drivers within Linux but are are
presented as a single device from device tree. It this case it is
necessary for each sub device to locate their supply data on the main
device.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
As Intel rolling out more SoC's after Moorestown, we need to
re-structure the code in a way that is backward compatible and easy to
expand. This patch implements a flexible way to support multiple boards
and devices.
This patch does not add any new functional support. It just refactors
the existing code to increase the modularity and decrease the code
duplication for supporting multiple soc's and boards.
Currently intel-mid.c has both board and soc related code in one file.
This patch moves the board related code to new files and let linker
script to create SFI devite table following this:
1. Move the SFI device specific code to
arch/x86/platform/intel-mid/device-libs/platform_<device>.*
A new device file is added for every supported device. This code will
get conditionally compiled by using corresponding device driver
CONFIG option.
2. Move the device_ids location to .x86_intel_mid_dev.init section by
using new sfi_device() macro.
This patch was based on previous code from Sathyanarayanan Kuppuswamy.
Signed-off-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Link: http://lkml.kernel.org/r/1382049336-21316-13-git-send-email-david.a.cohen@linux.intel.com
Signed-off-by: David Cohen <david.a.cohen@linux.intel.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
