forked from OERV-BSP/u-boot
057b1f8df9
The current default boot command does not respect the Linux kernel 2 MiB
alignment requirement, present on aarch64 [1]:
"
The Image must be placed text_offset bytes from a 2MB aligned base
address anywhere in usable system RAM and called there.
"
Adjust the boot command such, that it always places both Image and DT at
the nearest highest 2 MiB aligned offset. The DT is placed at lower 2 MiB
aligned address, the aarch64 Image is placed at the next higher 2 MiB
aligned address. Is is unlikely that a DT would be larger than 2 MiB on
these systems.
Replace use of hard-coded load addresses with generic ${loadaddr} aligned
using setexpr. This way, if user picks valid ${loadaddr}, their kernel and
DT address will be correctly set as well.
Fix up boot commands to use && instead of ; to exit the boot command early
in case of failure.
[1] https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/tree/Documentation/arch/arm64/booting.rst#n138
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
44 lines
1.5 KiB
Plaintext
44 lines
1.5 KiB
Plaintext
#include <configs/renesas_rcar3.config>
|
|
|
|
CONFIG_ARM=y
|
|
CONFIG_ARCH_RENESAS=y
|
|
CONFIG_RCAR_GEN3=y
|
|
CONFIG_COUNTER_FREQUENCY=16666666
|
|
CONFIG_ARCH_CPU_INIT=y
|
|
CONFIG_SYS_MALLOC_F_LEN=0x2000
|
|
CONFIG_ENV_SIZE=0x40000
|
|
CONFIG_ENV_OFFSET=0x700000
|
|
CONFIG_ENV_SECT_SIZE=0x40000
|
|
CONFIG_DEFAULT_DEVICE_TREE="renesas/r8a77970-eagle"
|
|
CONFIG_SPL_TEXT_BASE=0xe6318000
|
|
CONFIG_TARGET_EAGLE=y
|
|
CONFIG_SPL_HAVE_INIT_STACK=y
|
|
CONFIG_SPL_STACK=0xe6304000
|
|
CONFIG_SPL_HAS_BSS_LINKER_SECTION=y
|
|
CONFIG_SPL_BSS_START_ADDR=0xe631f000
|
|
CONFIG_SPL_BSS_MAX_SIZE=0x1000
|
|
# CONFIG_EFI_LOADER is not set
|
|
CONFIG_USE_BOOTARGS=y
|
|
CONFIG_USE_BOOTCOMMAND=y
|
|
CONFIG_BOOTCOMMAND="setexpr dloadaddr ${loadaddr} + 0x200000 && setexpr dloadaddr ${dloadaddr} \\\\& 0xffc00000 && setexpr kloadaddr ${dloadaddr} + 0x200000 && tftp ${dloadaddr} Image-r8a77970-eagle.dtb && tftp ${kloadaddr} Image && booti ${kloadaddr} - ${dloadaddr}"
|
|
CONFIG_DEFAULT_FDT_FILE="r8a77970-eagle.dtb"
|
|
# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set
|
|
CONFIG_CMD_DFU=y
|
|
CONFIG_OF_DTB_PROPS_REMOVE=y
|
|
CONFIG_OF_REMOVE_PROPS="dmas dma-names interrupt-parent interrupts interrupts-extended interrupt-names interrupt-map interrupt-map-mask iommus"
|
|
CONFIG_ENV_IS_IN_SPI_FLASH=y
|
|
CONFIG_ENV_RELOC_GD_ENV_ADDR=y
|
|
CONFIG_DFU_TFTP=y
|
|
CONFIG_DFU_RAM=y
|
|
CONFIG_DFU_SF=y
|
|
CONFIG_SYS_I2C_RCAR_I2C=y
|
|
# CONFIG_MMC is not set
|
|
CONFIG_SPI_FLASH_SPANSION=y
|
|
# CONFIG_SPI_FLASH_USE_4K_SECTORS is not set
|
|
CONFIG_PHY_MICREL=y
|
|
CONFIG_PHY_MICREL_KSZ90X1=y
|
|
CONFIG_DM_ETH_PHY=y
|
|
CONFIG_RENESAS_RAVB=y
|
|
CONFIG_TEE=y
|
|
CONFIG_OPTEE=y
|