The whole DRAM bank is used for loading and U-boot can detect the
overlap between the kernel and initramfs. So it is safe to drop
bootm_size.
Signed-off-by: Boyan Karatotev <boyan.karatotev@arm.com>
Signed-off-by: Leo Yan <leo.yan@arm.com>
Initialize the environment variables 'fdt_addr_r' and 'kernel_addr_r'
during the misc init phase. The static configurations are not needed,
remove them.
Signed-off-by: Boyan Karatotev <boyan.karatotev@arm.com>
Signed-off-by: Leo Yan <leo.yan@arm.com>
On Total Compute, TF-A passes the info via DT binding for the hardware
description - includes the serial, memory, and arm_ffa nodes.
This commit initializes the fdt base address based on the passed the
register x1.
The similar implementation has already been done for the raspberry pi,
so borrow a lot of it.
Co-developed-by: Jackson Cooper-Driver <jackson.cooper-driver@arm.com>
Signed-off-by: Jackson Cooper-Driver <jackson.cooper-driver@arm.com>
Signed-off-by: Boyan Karatotev <boyan.karatotev@arm.com>
Signed-off-by: Leo Yan <leo.yan@arm.com>
The Emcraft Systems NavQ+ kit is a mobile robotics platform
based on NXP i.MX8 MPlus SoC.
The following interfaces and devices are enabled:
- eMMC
- Gigabit Ethernet (through eQOS interface)
- SD-Card
- UART console
The device tree file is taken from upstream Linux Kernel
through OF_UPSTREAM
Signed-off-by: Gilles Talis <gilles.talis@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Jan Kiszka <jan.kiszka@siemens.com> says:
This adds support for the new IOT2050 SM variant, introduces a sysinfo
driver which also permits SMBIOS support and switches the board to
OF_UPSTREAM. There are some further fixes for the boards included as well.
Not yet included is configuration support for DMA isolation via the PVU as
this depends on not yet merged DT bindings and another overlay.
[trini: This is just the first 10 patches in the series for now]
Link: https://lore.kernel.org/r/cover.1729577070.git.jan.kiszka@siemens.com
Due to new DDR size introduction, the current logic of determining the
DDR size is not able to get the correct size.
Instead, the DDR size is determined by the FSBL(SEBOOT) then passed to
u-boot through the scratchpad info.
The SEBoot version must be >= D/V01.04.01.02 to support this change.
Also now for some variants, the DDR size may > 2GB, so borrow some code
from the TI evm to iot2050 to support more than 2GB DDR.
Signed-off-by: Baocheng Su <baocheng.su@siemens.com>
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
This prevented to set m2_manual_config - as evaluated by
m2_connector_setup - under strict configurations for secure boot.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Michael Trimarchi <michael@amarulasolutions.com>
QEMU supports NVMe devices, but U-Boot only tries to boot from Virtio.
This is problematic when explicitly using NVMe, so fix that.
Additionally, RVVM virtual machine is almost fully compatible with QEMU,
except it only implements NVMe drives instead of VirtIO.
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Patrick Rudolph <patrick.rudolph@9elements.com> says:
Based on the existing work done by Simon Glass this series adds
support for booting aarch64 devices using ACPI only.
As first target QEMU SBSA support is added, which relies on ACPI
only to boot an OS. As secondary target the Raspberry Pi4 was used,
which is broadly available and allows easy testing of the proposed
solution.
The series is split into ACPI cleanups and code movements, adding
Arm specific ACPI tables and finally SoC and mainboard related
changes to boot a Linux on the QEMU SBSA and RPi4. Currently only the
mandatory ACPI tables are supported, allowing to boot into Linux
without errors.
The QEMU SBSA support is feature complete and provides the same
functionality as the EDK2 implementation.
The changes were tested on real hardware as well on QEMU v9.0:
qemu-system-aarch64 -machine sbsa-ref -nographic -cpu cortex-a57 \
-pflash secure-world.rom \
-pflash unsecure-world.rom
qemu-system-aarch64 -machine raspi4b -kernel u-boot.bin -cpu cortex-a72 \
-smp 4 -m 2G -drive file=raspbian.img,format=raw,index=0 \
-dtb bcm2711-rpi-4-b.dtb -nographic
Tested against FWTS V24.03.00.
Known issues:
- The QEMU rpi4 support is currently limited as it doesn't emulate PCI,
USB or ethernet devices!
- The SMP bringup doesn't work on RPi4, but works in QEMU (Possibly
cache related).
- PCI on RPI4 isn't working on real hardware since the pcie_brcmstb
Linux kernel module doesn't support ACPI yet.
Link: https://lore.kernel.org/r/20241023132116.970117-1-patrick.rudolph@9elements.com
Add support for Arm sbsa [1] v0.3+ that is supported by QEMU [2].
Unlike other Arm based platforms the machine only provides a minimal
FDT that contains number of CPUs, ammount of memory and machine-version.
The boot firmware has to provide ACPI tables to the OS.
Due to this design a full DTB is added here as well that allows U-Boot's
driver to properly function. The DTB is appended at the end of the U-Boot
image and will be merged with the QEMU provided DTB.
In addition provide documentation how to use, enable binman to fabricate both
ROMs that are required to boot and add ACPI tables to make it full compatible
to the EDK2 reference implementation.
The board was tested using Fedora 40 Aarch64 Workstation. It's able
to boot from USB and AHCI or network.
Tested and found working:
- serial
- PCI
- xHCI
- Bochs display
- AHCI
- network using e1000e
- CPU init
- Booting Fedora 40
1: Server Base System Architecture (SBSA)
2: https://www.qemu.org/docs/master/system/arm/sbsa.html
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Cc: Peter Robinson <pbrobinson@gmail.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Tom Rini <trini@konsulko.com>
CI: https://source.denx.de/u-boot/custodians/u-boot-imx/-/pipelines/22989
- Remove unneeded USB board code and fix reset on mx6ul_14x14_evk.
- Update fastboot buffer size/address for verdin-imx8m{m|p}.
- Fix imxrt1050-evk boot and convert it to standard boot.
- Fix imx8qxp-mek and imx8qm-mek boot.
- Add support for the i.MX93 9X9 QSB board.
- Make livetree API to work on i.MX.
- Set sane default value for i.MX8M SPL_LOAD_FIT_ADDRESS.
- Deduplicate DH i.MX8MP/i.MX6 DHSOM defconfigs.
- Select default TEXT_BASE for i.MX6/i.MX7.
- Several updates for DH i.MX8MP DRC02.
The Hardkernel ODROID-M2 is a single-board computer based on Rockchip
RK3588S2 SoC. It features e.g. 8/16 GB LPDDR5 RAM, 64 GB eMMC, SD-card,
GbE LAN, HDMI 2.0, M.2 NVMe and USB 2.0/3.0/Type-C.
Features tested on a ODROID-M2 16GB rev1.0 20240611:
- SD-card boot
- eMMC boot
- Ethernet
- PCIe/NVMe
- USB gadget
- USB host
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
CI: https://source.denx.de/u-boot/custodians/u-boot-imx/-/pipelines/22796
- Switch to using upstream DT on DH i.MX8MP DHCOM PDK2/PDK3.
- Add ability to build fallback DTBOs from arch/$(ARCH)/dts.
- Remove fdt_high and initrd_high env variables from imx6-dhcom.
- Add dummy clk for imx8.
- Fix DT corruption in imx8_cpu.
- Improve DDR stability on pico-imx7d.
Remove both "fdt_high" and "initrd_high" environment variables
in favor of "bootm_size" to safely contain a kernel, device tree
and initrd for relocation inside of 256 MiB region of DRAM.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
This is cosmetic change.
Remove the empty comment blocks remaining after conversion to Kconfig
of CONFIG_SYS_MAX_NAND_DEVICE and CONFIG_SERVERIP.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Make the dh_update_sd_to_sf script generic, rename it to dh_update_block_to_sf
and implement two specific dh_update_sd_to_sf and dh_update_emmc_to_sf scripts
which load U-Boot from either SD or eMMC and install it into SPI NOR.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
When populating BOOT_TARGET_DEVICES on Amlogic Meson platforms, verify
that the shell commands for accessing the relevant media have been
enabled in the build configuration.
This was already being done for USB, NVME and SCSI devices, but not
for MMC devices or network boot. This meant that configuring U-Boot
without the networking or MMC subsystems/drivers would cause an error
to be thrown during preprocessing.
Signed-off-by: Callum Parsey <callum@neoninteger.au>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20241012080340.2596-1-callum@neoninteger.au
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Assorted Tegra enhancements. Merged with the recent XPL_BUILD changes,
resolve some whitespace issues and fix the name of the new apalis-tk1
env file by Tom.
Signed-off-by: Tom Rini <trini@konsulko.com>
Convert boards to use text based env. This is the first stage of
conversion, common inclusions should be converted next.
Acked-by: Francesco Dolcini <francesco.dolcini@toradex.com> # Toradex Apalis TK1
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Simon Glass <sjg@chromium.org> says:
When the SPL build-phase was first created it was designed to solve a
particular problem (the need to init SDRAM so that U-Boot proper could
be loaded). It has since expanded to become an important part of U-Boot,
with three phases now present: TPL, VPL and SPL
Due to this history, the term 'SPL' is used to mean both a particular
phase (the one before U-Boot proper) and all the non-proper phases.
This has become confusing.
For a similar reason CONFIG_SPL_BUILD is set to 'y' for all 'SPL'
phases, not just SPL. So code which can only be compiled for actual SPL,
for example, must use something like this:
#if defined(CONFIG_SPL_BUILD) && !defined(CONFIG_TPL_BUILD)
In Makefiles we have similar issues. SPL_ has been used as a variable
which expands to either SPL_ or nothing, to chose between options like
CONFIG_BLK and CONFIG_SPL_BLK. When TPL appeared, a new SPL_TPL variable
was created which expanded to 'SPL_', 'TPL_' or nothing. Later it was
updated to support 'VPL_' as well.
This series starts a change in terminology and usage to resolve the
above issues:
- The word 'xPL' is used instead of 'SPL' to mean a non-proper build
- A new CONFIG_XPL_BUILD define indicates that the current build is an
'xPL' build
- The existing CONFIG_SPL_BUILD is changed to mean SPL; it is not now
defined for TPL and VPL phases
- The existing SPL_ Makefile variable is renamed to SPL_
- The existing SPL_TPL Makefile variable is renamed to PHASE_
It should be noted that xpl_phase() can generally be used instead of
the above CONFIGs without a code-space or run-time penalty.
This series does not attempt to convert all of U-Boot to use this new
terminology but it makes a start. In particular, renaming spl.h and
common/spl seems like a bridge too far at this point.
The series is fully bisectable. It has also been checked to ensure there
are no code-size changes on any commit.
Oliver Gaskell <Oliver.Gaskell@analog.com> says:
ADSP-SC5xx is a series of ARM-based DSPs.
This comprises the armv7 based SC57x, SC58x and SC594 series, and the
armv8 based SC598.
This patch series includes configurations, init code, and minimal DTs
to enable Analog Devices' evaluation boards for these SoCs to boot
through SPL and into U-Boot Proper, as well as devicetree schemas for
the added DTs.
This patch series depends on ("arm: Add Analog Devices SC5xx Machine
Type") (https://lists.denx.de/pipermail/u-boot/2024-April/552043.html)
Adds support for Analog Devices' SC589-EZKIT board. Includes:
- Board specific configs in mach-sc5xx/Kconfig
- Board-specific Kconfig and environment in board/adi/
- Memory configuration
Signed-off-by: Oliver Gaskell <Oliver.Gaskell@analog.com>
Add support for the Comvetia i.MX6Q LXR2 board, which is
uses the Phytec PFLA02 SoM.
Based on the original work from Stefano Babic <sbabic@denx.de>.
The Phytec PFLA02 devicetrees are taken from kernel 6.11-rc7.
The imx6q-lxr.dts has been submitted upstream:
https://lore.kernel.org/linux-devicetree/20240913200906.1753458-3-festevam@gmail.com/
After it gets accepted in mainline (most likely in kernel 6.13),
the lxr2 board can then be switched to OF_UPSTREAM and these device trees
can be removed from U-Boot.
Signed-off-by: Fabio Estevam <festevam@denx.de>
AST2700 SoCs integrates a Ibex 32-bits RISC-V core as the boot MCU
for the first stage bootloader execution, namely SPL.
This patch implements the preliminary base to successfully run SPL
on this RV32-based MCU to the console banner message.
Signed-off-by: Chia-Wei Wang <chiawei_wang@aspeedtech.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
As per the maintainers at egnite GmbH, they are no longer interested in
supporting this board. Go and remove the platform here. Furthermore,
this is the only AT91SAM9XE platform in-tree so remove supporting code
for that as well.
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
The definition of CFG_MXC_USB_PORTSC as (PORT_PTS_UTMI | PORT_PTS_PTW)
can be removed from mx5/mx6/mx7/mx8m board config files as it is the
default in drivers/usb/host/ehci-mx5.c and drivers/usb/host/ehci-mx6.c.
Suggested-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Tim Harvey <tharvey@gateworks.com>
CFG_MXC_USB_FLAGS is only used for drivers/usb/host/ehci-mx5.c, so it
can be removed from all the imx6/imx7/imx8m board config files.
mx51evk.h is the only place CFG_MXC_USB_FLAGS is not set to 0.
Suggested-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
The SD card is registered as mmc device 0.
Fix it accordingly so that the board can boot to Linux
from the SD card.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Remove several comments that do not apply anymore to
the current file content.
While at it, write 'PMIC' into a single line for consistency.
Signed-off-by: Fabio Estevam <festevam@denx.de>
This command allows easy update on SD card or eMMC of the flash.bin
generated (with binman) during u-boot build.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Benjamin Hahn <B.Hahn@phytec.de>
Tested-by: Teresa Remmet <t.remmet@phytec.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Currently, the power_init_board() function is not executed because
CONFIG_POWER_LEGACY is not selected.
Convert to PMIC driver model, which allows removing board I2C code in
favor of the I2C driver model.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Only one board uses this option and it is very old. Let's drop it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
