Enable ENV_OVERWRITE to allow environment variables to be
overwritten within the board code. This is required to add
MAC addresses during SOM detection.
Additionally, set ENV_IS_NOWHERE for boot sources other than MMC.
Signed-off-by: Daniel Schultz <d.schultz@phytec.de>
Reviewed-by: Wadim Egorov <w.egorov@phytec.de>
Enable the GPIO command to allow access to the GPIO pins.
Signed-off-by: Daniel Schultz <d.schultz@phytec.de>
Reviewed-by: Wadim Egorov <w.egorov@phytec.de>
The phyBOARD-Electra does not include a PCA953x I2C GPIO multiplexer.
Remove this configuration as it is a remnant from another
defconfig, and enable CONFIG_DA8XX_GPIO for the DA8XX DaVinci GPIO
controller instead.
Signed-off-by: Daniel Schultz <d.schultz@phytec.de>
Reviewed-by: Wadim Egorov <w.egorov@phytec.de>
Increase the malloc pool size for the SPL by additional 4kB from
0x7000 to 0x8000.
This fixes following error message:
...
alloc space exhausted ptr 7028 limit 7000
DRAM init failed: -12
Signed-off-by: Daniel Schultz <d.schultz@phytec.de>
Update the image load address to ensure it matches the mt7629 NOR
controller's DMA alignment requirements.
Signed-off-by: Sam Shih <sam.shih@mediatek.com>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
Following the move of the H616 family to OF_UPSTREAM in the last cycle,
now some older SoCs with identical DTs follow the lead: the F1C100s, A10,
A10s, A13. The remaining SoCs suffer from that IRQ cells incompatiblity,
breaking support for Linux < v5.13, so I am holding their move back still.
Otherwise we get proper support for the PinePhone v1.2, and PSTORE support
for all revisions of that device.
This is rounded up by a PMIC related fix for some A80 boards, and two
cleanup patches that are preparations for two new SoCs families, being
worked on as we speak. But they have to wait for the next cycle.
Gitlab CI passed, and I booted that briefly on some boards.
Add bloblist support so that tables can be generated and placed in a
bloblist, then passed to a payload using UPL
Signed-off-by: Simon Glass <sjg@chromium.org>
If video is enabled we expect it to work. Avoid silent failure by adding
a panic if things go wrong.
Expand the SPL malloc-area for qemu-x86_64 to avoid a panic.
Signed-off-by: Simon Glass <sjg@chromium.org>
The space here is quite tight and there is plenty of room in the ROM.
Move SPL earlier to allow for expansion.
Signed-off-by: Simon Glass <sjg@chromium.org>
QEMU can have its own internal ACPI and SMBIOS tables. At present U-Boot
copies out the SMBIOS tables but points directly to the ACPI ones.
The ACPI tables are not aligned on a 4KB boundary, which means that UPL
cannot use them directly, since it uses a reserved-memory node for the
tables and that it assumed (by EDK2) to be 4KB-aligned.
On x86, QEMU provides the tables in a mapped memory region and U-Boot
makes use of these directly, thus making it difficult to use any common
code.
Adjust the logic to fit within the existing table-generation code. Use a
bloblist always and ensure that the ACPI tables is placed in an aligned
region. Set a size of 8K for QEMU. This does not actually put all the
tables in one place, for QEMU, since it currently adds a pointer to the
tables in QFW.
On ARM, enable bloblist so that SMBIOS tables can be added to the
bloblist.
Signed-off-by: Simon Glass <sjg@chromium.org>
In contrast to some other Allwinner SoCs, there is no difference between
the DTs for the Allwinner A10s/A13 SoCs (sun5i) between the U-Boot and the
Linux kernel repository.
Remove the old copies of the A10s/A13 related .dts and .dtsi files, and
switch most of sun5i boards over to use OF_UPSTREAM.
There are two boards for which we don't have DTs in the kernel tree.
Keep those two .dts files in the legacy U-Boot DT directory, and let
their defconfig opt out of OF_UPSTREAM.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Sumit Garg <sumit.garg@linaro.org>
In contrast to some other Allwinner SoCs, there is no difference between
the DTs for the Allwinner A10 SoCs (sun4i) between the U-Boot and the
Linux kernel repository.
Remove the old copies of the A10 related .dts and .dtsi files, and switch
most of sun4i boards over to use OF_UPSTREAM.
There are two boards for which we don't have DTs in the kernel tree.
Keep those two .dts files in the legacy U-Boot DT directory, and let
their defconfig opt out of OF_UPSTREAM.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Sumit Garg <sumit.garg@linaro.org>
In contrast to some other Allwinner SoCs, there is no difference between
the DTs for the Allwinner F1C100/F1C200 SoCs (sunvi) between the U-Boot
and the Linux kernel repository.
Remove the old copies of the F1Cx00 related .dts and .dtsi files, and
switch the whole suniv SoC over to use OF_UPSTREAM.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
In newer 1.2 PinePhone board revisions LIS3MDL magnetometer was replaced by
AF8133J. They use the same PB1 pin in different modes.
LIS3MDL uses it as an gpio input to handle interrupt.
AF8133J uses it as an gpio output as a reset signal.
It wasn't possible at runtime to enable both device tree
nodes and detect supported sensor at probe time.
AF8133J has reset pin (PB1) connected to the SoC. By default AF8133J
is in a reset state and don't respond to probe request on I2C
bus. Extra code would be needed to handle reset signal. Therefore this
code uses LIS3MDL magnetometer instead of AF8133J.
Introducing new dts 1.2b with AF8133J sensor would require probing in
SPL. That would lead to pulling in into SPL I2C controller driver,
RSB controller driver, introducing new AXP803 driver to power-up
sensors for probe. It's working, but SPL is pretty size-constrained on
A64 and doesn't have much space. Therefore fdt fixup is done in U-Boot
proper without introducing new board revision and new dts.
Signed-off-by: Andrey Skvortsov <andrej.skvortzov@gmail.com>
Link: https://lore.kernel.org/all/20240908214718.36316-1-andrej.skvortzov@gmail.com/
Link: https://lists.denx.de/pipermail/u-boot/2024-February/545700.html
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
[Andre: fix formatting]
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
pstore will allow users to catch kernel crashes and report them to
developers. Modern (Android) phones have pstore usually enabled to get
information about kernel crash, since it's the simplest way to get
kernel backtrace on mobile device without serial console. Usually it's
enabled by default in distribution kernels like Debian.
CONFIG_PSTORE=y
CONFIG_PSTORE_RAM=m
systemd has service that automatically handles pstore and saves them
in /var/lib/pstore for later usage.
In general any DRAM address, that isn't overwritten during a boot is
suitable for pstore.
Range from 0x40000000 - 0x50000000 is heavily used by u-boot for
internal use and to load kernel, fdt, fdto, scripts, pxefile and ramdisk
later in the boot process. Ramdisk start address is 0x4FF00000,
initramfs for kernel with some hacking features and debug info enabled
can take more than 100Mb and final address will be around 0x58000000.
Address 0x61000000 will most likely not overlap with that.
Signed-off-by: Andrey Skvortsov <andrej.skvortzov@gmail.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
The H616 DRAM controller requires some board specific parameters, which
we declare in Kconfig, let each board specify in their defconfig, and
then use in the DRAM init code.
Other DRAM controllers now require a very similar, if not identical
parameter set, with so far the same parameter names used.
To help keep the Kconfig file at bay, rename the existing parameter
names to drop the H616_ part in there, to make them more naturally
reusable for other SoCs.
No functional change, just a rename.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
We want to encourage people to use an allocated bloblist since it is
more flexible than a fixed one. Make this the default, being sure not to
change existing users.
The unit tests require BLOBLIST_FIXED so add a dependency in the
Makefile to avoid build errors.
All sandbox builds require BLOBLIST_FIXED so make that the default for
sandbox.
Signed-off-by: Simon Glass <sjg@chromium.org>
Move differences in DT files between upstream Linux DT and U-Boot DT to
mt7629-rfb-u-boot.dtsi.
Remove old copies of mt7629-related clock bindings, .dts, and .dtsi files.
Update defconfig to switch the whole mt7629 SoC to use OF_UPSTREAM.
Signed-off-by: Sam Shih <sam.shih@mediatek.com>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
Enable rudimentary nand read/write capability.
Changes in v2:
- New patch in series added enabling of nand functionality
Signed-off-by: david regan <dregan@broadcom.com>
Reviewed-by: William Zhang <william.zhang@broadcom.com>
Reviewed-by: Anand Gore <anand.gore@broadcom.com>
OSPI flash writing was broken on am62x SKs as the OSPI flash device has a
256k sector size but was set to 20k. This breaks OSPI flash writes because
the current implementation of the SF DFU backend requires that the DFU data
buffer size be the same as the sector erase size, and the USB DFU config
fragment (for both A53 and R5) reduced the size of the DFU data buffer,
presumably so that it can fit into SPL's much smaller heap.
Change the SYS_DFU_DATA_BUF_SIZE to the erase sector size, which still fits
within the post-relocation heap size in SPL.
Fixes: dfc2dff5a8 ("configs: am62x_evm_*: Enable USB and DFU support")
Signed-off-by: Jonathan Humphreys <j-humphreys@ti.com>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Capricorn boards have WDT (WDT_SIEMENS_PMIC) and U-Boot is not configured
to trigger the WDT. Enable the "wdt" command to be able to stop the WDT
from the command line.
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@siemens.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Add support for K230 CanMV board with serial console and usb otg
support. It can boot via vendor's u-boot-spl and boot into Linux
via tftp through the onboard RTL8152.
Signed-off-by: Junhui Liu <junhui.liu@pigmoral.tech>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Set CONFIG_NR_DRAM_BANKS to 2 as we have two banks described in the
memory/ node for lower and higher addressible DDR regions.
This allows use of FDT functions from fdt_support.c to set up and fix up
the memory/ node correctly.
Signed-off-by: Neha Malcom Francis <n-francis@ti.com>
Signed-off-by: Santhosh Kumar K <s-k6@ti.com>
