Enable the 'eeprom' command with support for EEPROM layout for Turris
Omnia. Enable the i2c-eeprom driver so that the EEPROM is accessed via
driver model.
Signed-off-by: Marek Behún <kabel@kernel.org>
For board revisions where the WAN ethernet PHY reset GPIO is controllable
via MCU we currently insert a phy-reset-gpios property into the ethernet
controller node. The mvneta driver parses this property and uses the
GPIO to reset the PHY.
But this phy-reset-gpios property is not a valid DT binding in upstream
kernel. Instead, a reset-gpios property should be inserted into the
ethernet PHY node. This correct DT binding is supported by the DM ETH PHY
U-Boot driver.
Insert the reset-gpios property into the WAN PHY node instead the
phy-reset-gpios property in WAN ETH node so that Linux will correctly use
the reset GPIO.
Enable the CONFIG_DM_ETH_PHY config option so that U-Boot will also use
the correct DT property.
Note: currently there are 4 ethernet controller drivers parsing the
wrong DT property: dwc_eth_qos, fex_mxc, mvneta and mvpp2. We should
convert all relevant device-trees to use reset-gpios so that we can get
rid of these drivers parsing this property.
Fixes: 1da53ae26a ("arm: mvebu: turris_omnia: Add support for design with SW reset signals")
Signed-off-by: Marek Behún <kabel@kernel.org>
Turris Omnia defconfig is nearing image size limit. Disable ext4 write
support to reserve space for more important stuff.
This reduces the size of the KWB image by ~19 KiB.
If in the future U-Boot supports compressing itself and decompressing
on load, we may enable this again.
Signed-off-by: Marek Behún <kabel@kernel.org>
Switch PHY_ANEG_TIMEOUT to CONFIG_PHY_ANEG_TIMEOUT Kconfig symbol.
This removes one more configuration headers option finalizes its
Kconfig symbol conversion. No functional change expected.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Now that Turris Omnia has a rng driver provided in the MCU driver,
enable the rng command in defconfig.
Signed-off-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Add support for true random number generator provided by the MCU on
Turris Omnia. The MCU firmware supports TRNG if the FEAT_TRNG bit is set
in features. In that case we bind the rng driver.
Signed-off-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Enable support for the poweroff command via sysreset for Turris Omnia.
Signed-off-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Add support for system power off via UCLASS_SYSRESET. Newer versions of
Turris Omnia MCU firmware can power off the board (MCU will disable
almost all voltage regulators and go into low power mode).
Move the MCU driver into drivers/misc and register it under UCLASS_MISC.
The sysreset and gpio device are bound as child devices of the MCU device.
Signed-off-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
U-Boot builds for Turris Omnia are approaching the limit of 0xf0000
bytes, which is the size of the U-Boot partition on Omnia.
Enable LTO to get more size optimized binaries.
Signed-off-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
The Turris Omnia contains the Marvell 88E6176 ethernet switch. Add
config options and device tree to enable the support.
Signed-off-by: Marek Mojík <marek.mojik@nic.cz>
Signed-off-by: Marek Behún <kabel@kernel.org>
The help for CONFIG_MTD explains that it needs to be enabled for various
things like NAND, etc to be available. It however then doesn't enforce
this dependency and so if you have none of these systems present you
still need to disable a number of options. Fix this by making places
that select/imply one type of flash, but did not do the same, also do
this for "MTD". Make boards which hadn't been enabling MTD already but
need it now, do so. In a few places, disable CONFIG_CMD_MTDPARTS as it
wasn't previously enabled but was now being implied.
Signed-off-by: Tom Rini <trini@konsulko.com>
The current name is inconsistent with SPL which uses CONFIG_SPL_TEXT_BASE
and this makes it imposible to use CONFIG_VAL().
Rename it to resolve this problem.
Signed-off-by: Simon Glass <sjg@chromium.org>
VHV gpio is connected to MCU and only on updated board design. Without it
eFUSE programming does not work. Omnia MCU driver exports this GPIO to
U-Boot under name mcu_56 and only when it is supported by MCU. So U-Boot
fuse command refuse eFUSE programming on older board design when VHV gpio
is not available.
We tested that Armada 385 without connected VHV gpio can do eFUSE
programming but only for some bits and only sometimes - it is unstable.
And better to be disabled on older board design without VHV gpio support.
Signed-off-by: Pali Rohár <pali@kernel.org>
Maximal size of u-boot kwb image binary is $CONFIG_ENV_OFFSET which is
0xF0000 = 983040 bytes. So add missing CONFIG_BOARD_SIZE_LIMIT definition
to ensure that u-boot binary does not overflow to the u-boot env storage.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Turris Omnia has two serial ports. Both are already specified in device
tree file. But U-Boot by default does not allow to use more than one serial
port unless CONFIG_SERIAL_PROBE_ALL is not enabled.
After enabling CONFIG_SERIAL_PROBE_ALL, U-Boot see also second serial port
(but is inactive by default):
=> coninfo
List of available devices:
serial@12000 00000007 IO stdin stdout stderr
serial@12100 00000007 IO
To allow simultaneously to use more input / output devices it is needed to
enable CONFIG_CONSOLE_MUX option.
With CONFIG_CONSOLE_MUX it is possible to call:
=> setenv stdout 'serial@12000,serial@12100'
And U-Boot output is then visible on both serial ports.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Some new Omnia boards will come with Winbond SPI flash. Add to
defconfig.
Signed-off-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
CONFIG_ETHPRIME can be set to DT node name or alias which refers to DT
node. Define ethernet aliases and set ETHPRIME to eth2 which refers to WAN
ethernet port. This removes hardcoded DT node name from U-Boot
configuration file.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
- Make all users of CUSTOM_SYS_INIT_SP_ADDR reference SYS_INIT_SP_ADDR
- Introduce HAS_CUSTOM_SYS_INIT_SP_ADDR to allow for setting the stack
pointer directly, otherwise we use the common calculation.
- On some platforms that were using the standard calculation but did not
set CONFIG_SYS_INIT_RAM_SIZE / CONFIG_SYS_INIT_RAM_ADDR, set them.
- On a small number of platforms that were not subtracting
GENERATED_GBL_DATA_SIZE do so now via the standard calculation.
- CONFIG_SYS_INIT_SP_OFFSET is now widely unused, so remove it from most
board config header files.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SPL_BSS_MAX_SIZE
CONFIG_SPL_MAX_FOOTPRINT
Note that the da850evm platforms were violating the "only use one" rule
here, and so now hard-code their BSS limit.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SPL_PAD_TO
CONFIG_SPL_MAX_SIZE
CONFIG_TPL_PAD_TO
CONFIG_TPL_MAX_SIZE
Note that we need to make TPL_MAX_SIZE be hex, and so move and convert the
existing places.
Signed-off-by: Tom Rini <trini@konsulko.com>
Internal registers in SPL are at address 0xd0000000 and in proper U-Boot at
address 0xf1000000. UART base address is located in internal registers.
Fix DEBUG_UART_BASE option to correct value for both SPL and proper U-Boot.
This change fixes hangup of proper U-Boot when it is trying to print
something via debug UART.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Stop parsing fixed-link in the MAC driver. Instead support only PHY mode
and let the fixed PHY driver handle the fixed-link case.
Enable CONFIG_PHY_FIXED for mvneta boards that need it: Turris Omnia and
ESPRESSObin.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Use the modern DM MDIO API for connecting PHY in the mvneta driver.
This requires enabling MVMDIO driver in several config files.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
CONFIG_ETHPRIME defines primary ethernet device and env variable $ethact
stores currently active ethernet device.
So there is no point to set ethact= in default environment. Instead set
CONFIG_ETHPRIME properly.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Enable ext4 write support in Turris Omnia's defconfig. Some users find
it useful.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
The state of the current DDR training code for Armada 38x is such that
we cannot be sure it will always train successfully - although after the
last change we were yet unable to find a board that failed DDR training,
from experience in the last 2 years we know that it is possible.
The experience also tells us that in many cases the board fails training
only sometimes, and after a reset the training is successful.
Enable the new option that makes the board reset itself on DDR training
failure immediately. Until now we called hang() in such a case, which
meant that the board was reset by the MCU after 120 seconds.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Pali Rohár <pali@kernel.org>
Apple SoCs have an integrated NVMe controller that isn't connected
over a PCIe bus. In preparation for adding support for this NVMe
controller, split out the PCI support into its own file. This file
is selected through a new CONFIG_NVME_PCI Kconfig option, so do
a wholesale replacement of CONFIG_NVME with CONFIG_NVME_PCI.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested on: Macbook Air M1
Tested-by: Simon Glass <sjg@chromium.org>
On of the MiniPCIe ports on Turris Omnia is also a mSATA port. Whether
it works in SATA or PCIe mode is determined by a strapping pin, which
value is read from the MCU.
We already determine which type of card is connected when configuring
SerDeses.
But until now we left both SATA and PCIe port 0 nodes in device tree
enabled, and so the SATA driver is probed in U-Boot / Linux even if we
know there is no mSATA card, and similarly PCIe driver tries to link on
port 0 even if we know there is mSATA card, not a PCIe card.
Fixup device tree blob to disable SATA node if mSATA card is not
present, and to disable PCIe port 0 node if mSATA card is present.
Do this for U-Boot's DT blob before relocation and also for kernel DT
blob before booting.
This ensures that software does not try to use SATA or PCIe HW when
corresponding PHY is not configured.
Signed-off-by: Pali Rohár <pali@kernel.org>
[ refactored and fixed some issues ]
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
This converts the following to Kconfig:
CONFIG_ENV_SPI_BUS
CONFIG_ENV_SPI_CS
CONFIG_ENV_SPI_MAX_HZ
CONFIG_ENV_SPI_MODE
As part of this, we use Kconfig to provide the defaults now that were
done in include/spi_flash.h. We also in some cases change from using
CONFIG_ENV_SPI_FOO to CONFIG_SF_DEFAULT_FOO as those were the values in
use anyhow as ENV was not enabled.
Signed-off-by: Tom Rini <trini@konsulko.com>
