Migrate RK3588 boards that exists in Linux v6.8 to use OF_UPSTREAM.
Following targets is not migrated to use OF_UPSTREAM:
- generic-rk3588: Generic target only meant for U-Boot use
- toybrick-rk3588: Merged in v6.9-rc1
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
RK3588-based devices now support creating DRAM banks with proper holes
by reading the ATAGS from Rockchip TPL blob, so let's use that mechanism
instead.
Since ft_board_setup isn't defined anymore, there's no need for
selecting CONFIG_OF_BOARD_SETUP.
Similarly, because the evb_rk3588.c would be empty, it is simply
removed, with the (would-be-empty) Makefile as well.
The CONFIG_NR_DRAM_BANK now defaults to 10 which is a safe bet for
reading banks from ATAGS, so let's use the default value instead.
All defconfigs using the CONFIG_TARGET_EVB_RK3588 are updated at once
since they are impacted by this change.
Co-developed-by: Chris Morgan <macromorgan@hotmail.com>
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The generic RK35xx board targets are intended to be used as a bare
minimum target that can be used to e.g. boot boards that mostly follow
reference hw design before a board spefic target has been added or for
flashing and recovery purposes.
Disable BOOTMETH_VBE, NET and ADC as these features are not intended to
ever be used by these minimal generic board targets.
Enable SYSRESET_PSCI to let TF-A handle sysreset from U-Boot proper.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add support for USB OTG, RockUSB and UMS to the generic RK3588S/RK3588
target.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Currently the following memory layout is typically used on RK3588:
[ 0, 256K) - SPL binary
[ 256K, 2M) - TF-A / reserved
[ -X, 4M) - SPL pre-reloc stack (SPL_STACK)
[ 3.5M, 4M) - pre-reloc malloc heap (SPL_SYS_MALLOC_F_LEN)
[ -X, 6M) - SPL reloc stack (SPL_STACK_R_ADDR)
[ 5M, 6M) - reloc malloc heap (SPL_STACK_R_MALLOC_SIMPLE_LEN)
[ 10M, +X) - U-Boot proper binary (TEXT_BASE)
[ -X, 12M) - U-Boot proper pre-reloc stack (CUSTOM_SYS_INIT_SP_ADDR)
[11.5M, 12M) - pre-reloc malloc heap (SYS_MALLOC_F_LEN)
[ 64M, +16K) - SPL bss (SPL_BSS_START_ADDR, SPL_BSS_MAX_SIZE)
SPL can safely load U-Boot proper + FDT to [10M, 11.5M) with this layout.
However, on ROCK 5A the SPL stacks is overlapping:
[ -X, 16M) - SPL pre-reloc stack (SPL_STACK)
[15.5M, 16M) - pre-reloc malloc heap (SPL_SYS_MALLOC_F_LEN)
[ -X, 16M) - SPL reloc stack (SPL_STACK_R_ADDR)
[ 15M, 16M) - reloc malloc heap (SPL_STACK_R_MALLOC_SIMPLE_LEN)
Because bind and probe udevice instanses is allocated on the pre-reloc
malloc heap, there is going to be an overlap when reloc malloc heap
reaches close to 512 KiB of usage.
Migrate to use common bss, stack and malloc heap size and addresses to
mitigate these limitations and allow for a larger U-Boot proper size.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
(Update for new boards defconfig)
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Add a minimal generic RK3588S/RK3588 board that only have eMMC and SDMMC
enabled. This defconfig can be used to boot from eMMC or SD-card on most
RK3588S/RK3588 boards that follow reference board design.
Also fix the alphabetical order of RK3588 boards listed in Makefile and
documentation.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
