Judith Mendez <jm@ti.com> says:
Some K3 devices like am62x and am64x have a M4 processor in the MCU
voltage domain. This patch series introduces remoteproc M4 driver which
will be used to load firmware into and start the M4 remote core.
This series also adds support for R5F cores on am64x SoCs in patch 2 and
sets up environment to load FW in remote cores in patch 3,4,5.
This patch series also enables remoteproc drivers by default as per what
remoteproc sybsystem is supported per SoC, thus all remoteproc options
are now deleted in configs/* since they are no longer required.
This patch series was tested on am64x EVM, am62x SK, am62ax SK,
am62px SK boards.
Any additional tested by's are welcome since I was not able to
test any additional boards.
Tested by running the following commands in u-boot prompt:
=> setenv dorprocboot 1
=> run boot_rprocs
Link: https://lore.kernel.org/r/20250210202944.1071931-1-jm@ti.com
Now that remoteproc configs are enabled by default in Kconfig
files, remove these configs which are no longer needed to be
defined here in configs/.
Signed-off-by: Judith Mendez <jm@ti.com>
Reviewed-by: Andrew Davis <afd@ti.com>
Judith Mendez <jm@ti.com> says:
This patch series enables ESM reset configuration in board_init_f
for am62x and am62px devices.
This is necessary in order for error events to reset the system.
This patches are tested using watchdog to reset the system via ESM.
Link: https://lore.kernel.org/r/20250129234403.574766-1-jm@ti.com
Enable CONFIG_SPL_DRIVERS_MISC, CONFIG_SPL_MISC, CONFIG_ESM_K3
to probe the Main ESM and MCU ESM nodes.
Signed-off-by: Santhosh Kumar K <s-k6@ti.com>
Signed-off-by: Judith Mendez <jm@ti.com>
Prepare the introduction of the lwIP (lightweight IP) TCP/IP stack by
adding a new net/lwip/ directory and the NET_LWIP symbol. Network
support is either NO_NET, NET (legacy stack) or NET_LWIP. Subsequent
commits will introduce the lwIP code, re-work the NETDEVICE integration
and port some of the NET commands and features to lwIP.
SPL_NET cannot be enabled when NET_LWIP=y. SPL_NET pulls some symbols
that are part of NET (such as arp_init(), arp_timeout_check(),
arp_receive(), net_arp_wait_packet_ip()). lwIP support in SPL may be
added later.
Similarly, DFU_TFTP and FASTBOOT are not compatible with NET_LWIP
because of dependencies on net_loop(), tftp_timeout_ms,
tftp_timeout_count_max and other NET things. Let's add a dependency on
!NET_LWIP for now.
SANDBOX can select NET_LWIP but doing so will currently disable the eth
dm tests as well as the wget tests which have strong dependencies on the
NET code.
Other adjustments to Kconfig files are made to fix "unmet direct
dependencies detected" for USB_FUNCTION_SDP and CMD_FASTBOOT when
the default networking stack is set to NET_LWIP ("default NET_LWIP"
instead of "default NET" in Kconfig).
The networking stack is now a choice between NO_NET,
NET and NET_LWIP. Therefore '# CONFIG_NET is not set' should be
'CONFIG_NO_NET=y'. Adjust the defconfigs accordingly.
Signed-off-by: Jerome Forissier <jerome.forissier@linaro.org>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Make the raw-mode options depend on SPL_SYS_MMCSD_RAW_MODE in a more
direct way. This makes it easier to understand the options with
'make menuconfig'.
There are three different ways of specifying the offset:
- sector offset
- partition number
- partition type
So make these a choice, so it is more obvious what is going on.
Update existing boards to enable SPL_SYS_MMCSD_RAW_MODE where needed.
Reviewed-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Quentin Schulz <quentin.schulz@cherry.de>
Signed-off-by: Simon Glass <sjg@chromium.org>
All ARCH_K3 platforms need about of 2MB of malloc space post
reallocation. Since, this space is allocated from SDRAM, provide a
generous 2MB space by default.
Platforms requiring more than 2MB can override in defconfig as needed.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Francesco Dolcini <francesco.dolcini@toradex.com>
