1. Replace usage of "/dev/mmcblk*p*" with a proper UUID of rootfs
partition. This fixes the issue, when MMC controllers are probed in
a different order in U-boot and Linux kernel.
2. Fix legacy USB command (both sdboot and usbboot can be used now).
Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
This patch enable convert DM MMC for imx7d-pico board and variant.
Before the DM conversion only usdhc3 was enabled and therefore it appeared
as MMC 0 to u-boot. After enabling MMC DM though usdhc3 defaults to MMC 2,
which left unattended would drive changes to existing pico-pi bootscripts and
environment variables that rely on mmc 0.
Setup the alias of mmc0 and usdhc3 so that existing pico-imx7d boot code will
work unmodified.
When converting to DM_MMC it is necessary that SPL initializes eMMC
by itself, so move the original eMMC initialization from U-Boot
proper to SPL.
Signed-off-by: Joris Offouga <offougajoris@gmail.com>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
This patch is necessary for convert this board to dm driver model
DM GPIO requires gpio_request() to be called explicitly before
doing any gpio operation
Signed-off-by: Joris Offouga <offougajoris@gmail.com>
Migrate Ethernet FEC to using driver model.
Drop PHY_MICREL_KSZ90X1 which slipped in from Apalis iMX6.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Migrate USB to using driver model.
Add USBH_PEN GPIO regulator.
While at it also add alias e.g. as required for UMS.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Migrate MMC to using driver model.
Migrate USDHC to using pinctrl.
While at it also add GPIO1_IO03__OSC32K_32K_OUT pin muxing.
While at it also update copyright period.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Migrate pinctrl and regulators to device tree resp. driver model:
Ethernet, NAND and UART.
Drop BOARD_EARLY_INIT_F as it is anyway no longer used.
Enable CMD_DM, CMD_MTD, CMD_REGULATOR and DM_REGULATOR_FIXED.
While at it also update copyright period.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Drop disabling SPL_SYS_THUMB_BUILD as we anyway do not use SPL.
Enbale CRC32 verify, USB SDP and EFI loader support.
Drop CMD_GPT and disabling RANDOM_UUID.
Do savedefconfig which drops USB_FUNCTION_SDP.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
with u-boot,dm-spl added for imx8qx-pm node, and SPL_SIMPLE_BUS enabled,
the bind and probe code in board file could be removed.
Also we need to enlarge SYS_MALLOC_F_LEN to avoid calloc fail.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Some variations of the imx6q_logic board have eMMC instead of
NAND. Rather than creating a separate defconfig, this patch
adds the ability to read/write to eMMC (mmc 0:1) when NAND
doesn't exist.
Signed-off-by: Adam Ford <aford173@gmail.com>
All socfpga boards except for vining_fpga use DM_I2C. Enable
DM_I2C for this board and set the EEPROM defines via Kconfig
(enabling CONFIG_I2C_EEPROM from MISC).
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Series-changes: 2
- added (this) patch to move socfpga_vining to DM_I2C
This commit moves common config options used in all socfpga boards
to select/imply in Kconfig. This both cleans up the defconfig files
as well as makes future changes easier.
Options implied/defaulted for all sub-arches:
- SPL, SPL_DM, USE_TINY_PRINTF, NR_DRAM_BANKS
Options implied/defaulted for implied for A10 & gen5:
- FPGA_SOCFPGA, SYS_MALLOC_F_LEN, SYS_TEXT_BASE
Options implied/defaulted for gen5:
- SPL_STACK_R, SPL_SYS_MALLOC_SIMPLE, SPL_STACK_R_ADDR
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Acked-by: Marek Vasut <marex@denx.de>
This enables DM_RTC and RTC_M41T62 to enable support for the rtc on the
socrates board.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Pull request for UEFI sub-system for v2019.07-rc1 (3)
This patch series reworks the implementation of the `bootefi` command to
remove code duplication by using the LoadImage() boot service to load
binaries.
Missing short texts for UEFI protocols are added for display by the
`efidebug dh` command.
Missing parameter checks for AllocatePages() and CreateDeviceNode() are
implemented.
The constants for protocol GUIDs are changed to match the names in the UEFI
specification.
- Add support for Amlogic p200 & p201 Reference Designs
- Add Amlogic SoC information display
- Add support for the Libretech-AC AML-S805X-AC board
- Add Amlogic AXG reset compatible
- Add I2C support for Amlogic AXG
- Fix AXG PIN and BANK pinctrl definitions
- Fix regmap_read_poll_timeout warning about sandbox_timer_add_offset
- Add initial support for Amlogic G12A SoC and U200 board
- Enable PHY_REALTEK for selected boards
- Fix Khadas VIM2 README
These two buffers currently conflict if tracing is enabled. Move the
pre-console buffer and update the documentation.
Signed-off-by: Simon Glass <sjg@chromium.org>
The 'phy' reset of gmac device in kernel device tree is not generic
enough for u-boot to use, so we need to overwrite the 'resets' property
as needed. With this device tree fixup and poplar_defconfig changes,
Ethernet starts working on Poplar board.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This config file is shared between stm32f746-disco and stm32f769-disco.
These 2 boards doesn't embed the same qspi flash (Micron n25q128a on
f746-disco, Macronix mx66l51235l on f769-disco).
To be able to use Macronix mx66l51235l on F769-disco, flags
SPI_FLASH_MACRONIX must be enabled.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
When using the generic PHY on boards using an RGMII Realtek PHY,
gigabit speed is not always reliable.
This patch enables the Realtek PHY driver for such boards.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
The Amlogic U200 board is based on the Amlogic S905D2 SoC
from the Amlogic G12A SoC family.
The board has the following specifications :
- Amlogic S905D2 ARM Cortex-A53 quad-core SoC
- XGB DDR4 SDRAM
- 10/100 Ethernet (Internal PHY)
- 1 x USB 3.0 Host
- eMMC
- SDcard
- Infrared receiver
- SDIO WiFi Module
- MIPI DSI Connector
- Audio HAT Connector
- PCI-E M.2 Connector
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
vexpress_ca15_tc2_defconfig and vexpress_ca9x4_defconfig do not provide
device trees (as $fdtcontroladdr) as needed to pass our Travis CI tests.
As we are on the move to requiring block devices to be based on the driver
model these boards either will have to be converted to use device trees or
will be kicked out of U-Boot.
So let's disable CONFIG_EFI_LOADER on these boards until the device tree
issue is resolved.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Enable the nand support (driver and command)
in the configuration of the board bcm963158.
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
Enable the nand support (driver and command)
in the configuration of the board bcm968580xref.
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
Enable the nand support (driver and command)
in the configuration of the board bcm96838gerg.
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
Use the DWC2 device driver with DM_USB_GADGET support and
cleanup the USB support in STM32MP1 board.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Remove the HOST support for STM32MP1 USBO device = OTG DWC2.
The current DWC2 driver have no dynamic detection of device,
So it is dangerous to have start 3V3 when PC is
connected to the micro USB connector.
=> it is preferable to have only DEVICE support
CONFIG_USB_GADGET_DWC2_OTG for OTG port
See DWC3 driver for clean dual role support...
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
USB_MUSB_TI requires USB_MUSB_DSPS, failing at link time if it's not
selected:
drivers/usb/musb-new/built-in.o: In function `ti_musb_host_ofdata_to_platdata':
drivers/usb/musb-new/ti-musb.c:193: undefined reference to `musb_dsps_ops'
or if OF_CONTROL is not selected:
arch/arm/mach-omap2/built-in.o:(.data.usb0+0x24): undefined reference to `musb_dsps_ops'
Reviewed-by: Hannes Schmelzer <oe5hpm@oevsv.at>
Tested-by: Hannes Schmelzer <oe5hpm@oevsv.at>
Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
Beelink GS1 is an Allwinner H6 based TV box,
which support:
- Allwinner H6 Quad-core 64-bit ARM Cortex-A53
- GPU Mali-T720
- 2GB LPDDR3 RAM
- 16GB eMMC
- AXP805 PMIC
- 1Gbps GMAC via RTL8211E
- USB 2.0 and 3.0 Host
- HDMI port
- S/PDIF port
- 5V/2A DC power supply
- Wi-Fi/BT via Fn-Link 6222B-SRB (RTL8222BS)
Linux commit details about the sun50i-h6-beelink-gs1.dts sync:
"arm64: dts: allwinner: h6: Introduce Beelink GS1 board"
(sha1: 089bee8dd119ba084dee6b17a2e1a53df4f30193)
Signed-off-by: Clément Péron <peron.clem@gmail.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
