Add SPL support for the Technexion TAO3530 SOM to replace
x-loader. Tested with the Thunder baseboard. Currently this is
only tested with the TAO3530 SOM revision (Ax/Bx).
Tested by booting via MMC and NAND.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Tapani Utriainen <tapani@technexion.com>
Cc: Thorsten Eisbein <thorsten.eisbein@head-acoustics.de>
Cc: Tom Rini <trini@ti.com>
Add support for TechNexion TAO3530 SoM
This patch has been posted quite a long time ago. I ported it to
the latest mainline U-Boot version. With some additional cleanup
and enhancements.
Signed-off-by: Tapani Utriainen <tapani@technexion.com>
CC: Sandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Thorsten Eisbein <thorsten.eisbein@head-acoustics.de>
Cc: Tom Rini <trini@ti.com>
With the current scenario SPL size is being overlapped with the public
stack and not allowing any OMAP4 device to boot. So the suggestion came
up was to move the TEXT_BASE down to non-HS limit. Fixing the same and
also moving the SRAM_SCRATCH_SPACE_ADDR up to the end of image
downloadable area.
Discussion on this can be seen here:
https://www.mail-archive.com/u-boot@lists.denx.de/msg127147.html
Tested on OMAP4460 PANDA.
Reported-by: Chao Xu <caesarxuchao@gmail.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
We want to test SPI flash code in the sandbox, so enable the new drivers and
the 'sf test' command.
This command is used to validate the sandbox SPI / SPI flash implementation,
so enable it.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
This allows us to put the SPI flash chip inside the SPI interface node,
with U-Boot finding the correct bus and chip select automatically.
Signed-off-by: Simon Glass <sjg@chromium.org>
Fixes this error message when USB is started.
"ULPI: ulpi_reset: failed writing reset bit"
It is pointless to manually reset the ULPI as the USB Host
Reset and PHY RESET line should take care of that.
Reported-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Fixes this error message when USB is started.
"ULPI: ulpi_reset: failed writing reset bit"
It is pointless to manually reset the ULPI as the USB Host
Reset and PHY RESET line should take care of that.
Reported-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Roger Quadros <rogerq@ti.com>
MPC8349 has been using mpc85xx DDR driver through a symbolic link to
mpc85xx_ddr_gen2.c. After consolidating the drivers to a single set
under driver/ddr/fsl/, the link is replaced by referring driver
directly. We now can simply enable the macro and use the driver.
Other mpc83xx SoCs still use their own driver.
Signed-off-by: York Sun <yorksun@freescale.com>
Usually CONFIG_FSL_DDR_INTERACTIVE feature is used for debug.
we would not enable this by default to save the limited space of u-boot.
This avoid following compiling error:
section .bootpg loaded at [00000000effff000,00000000effff577] overlap ssection
.data loaded at [00000000efff31b8,00000000f00010c7]
u-boot: section .bootpg lma 0xeffff000 adjusted to 0xf00010c8
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Acked-by: York Sun <yorksun@freescale.com>
In new board P1010RDB-PB, the interrupt vector table is at
the start of memory. So if the start_address needs to be set
a proper value.
Signed-off-by: Zhao Qiang <B45475@freescale.com>
Acked-by: York Sun <yorksun@freescale.com>
Add support for the 16 bits pca9555 i2c to gpio extender featured
by the SB-T335 baseboard.
Signed-off-by: Ilya Ledvich <ilya@compulab.co.il>
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Add support for status LED. Use the STATUS_LED APIs for indicating a
boot progress.
Signed-off-by: Ilya Ledvich <ilya@compulab.co.il>
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
This patch implements a custom spi_copy funtion to copy u-boot from SF
to RAM. This is faster then iROM spi_copy funtion as this runs spi at
50Mhz and also in WORD mode of operation.
Changed a printf in pinmux.c to debug just to avoid the compilation
error in SPL.
Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Tom Wai-Hong Tam <waihong@chromium.org>
Signed-off-by: Rajeshwari S Shinde <rajeshwari.s@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
In config_cmd_default.h, it will use CONFIG_SYS_NO_FLASH to decide
whether include CONFIG_CMD_FLASH and CONFIG_CMD_IMLS. So, if the
CONFIG_SYS_NO_FLASH defined later than include/config_cmd_default.h,
These two commands will be included always.
So move CONFIG_SYS_NO_FLASH definition to proper position.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
