Fix PHYTEC EEPROM bus mismatch between SPL and U-Boot proper by enabling
CONFIG_SPL_DM_SEQ_ALIAS=y on phyCORE-i.MX93 boards. This way, both the
SPL and U-Boot proper will respect the device-tree aliases for I2C devs
and use the same I2C bus number for phytec_eeprom_data_setup() function
calls. This makes code less confusing and more robust.
Fixes an issue apparent since commit 79f3e77133 ("Subtree merge tag
'v6.16-dts' of dts repo [1] into dts/upstream") where SPL would spew the
following error:
phytec_eeprom_read: i2c EEPROM not found: -110.
phytec_eeprom_data_setup: EEPROM data init failed
While later in U-Boot proper, EEPROM would be successfully read out.
This happens because Linux device-tree for phyBOARD-Segin-i.MX93 since
aforementioned commit enables I2C bus 2 (lpi2c2 is used for audio codec
and RTC) which breaks SPL I2C bus number ordering and I2C EEPROM bus is
shifted by +1. Now, lets prevent this from happening again by utilizing
device-tree aliases also in the SPL.
Signed-off-by: Primoz Fiser <primoz.fiser@norik.com>
Add configs to enable Ethernet boot in R5SPL, also disable not required
configs to avoid memory limitation.
Signed-off-by: Chintan Vankar <c-vankar@ti.com>
Add configs for enabling Ethernet boot in R5SPL, also disable not required
configs to avoid memory limitation.
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Signed-off-by: Chintan Vankar <c-vankar@ti.com>
Add configs for enabling Ethernet boot in R5SPL, also disable not required
configs to avoid memory limitation.
Signed-off-by: Chintan Vankar <c-vankar@ti.com>
Set the uart clock frequency according to dts by default.
If CONFIG_SYS_SKIP_UART_INIT is not enabled, no need to
do board_set_console to change the console bootarg.
Signed-off-by: Jim Liu <JJLIU0@nuvoton.com>
The Renesas board defconfigs explicitly set CONFIG_TEXT_BASE=0x50000000,
however U-Boot's POSITION_INDEPENDENT=y build default already places text
at 0x0. These hardcoded overrides are therefore unnecessary and will be
pruned automatically in upcoming resyncs.
Remove the CONFIG_TEXT_BASE lines from the following defconfigs:
- hihope_rzg2_defconfig
- r8a77970_eagle_defconfig
- r8a77970_v3msk_defconfig
- r8a77990_ebisu_defconfig
- r8a77995_draak_defconfig
- r8a779a0_falcon_defconfig
- renesas_rzg2l_smarc_defconfig
- rz2_beacon_defconfig
- silinux_ek874_defconfig
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Enable support for PCIe based xHCI USB 3.0 driver and USB mass
storage support on Retronix R-Car V4H Sparrow Hawk board .
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
The symbol "SM" is a library symbol and should not be prompted for. It
should be selected by the drivers that use it. In this case we need to
add a SANDBOX_SM symbol for the sandbox driver. The meson SM driver
cannot build on other platforms, so add the appropriate dependency.
Reviewed-by: Peter Robinson <pbrobinson@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Enable CONFIG_OF_BOARD_SETUP and other dependencies to allow the use of
the ft_board_setup() function to replace fdt set in boot scripts for
Microchip's MPFS Icicle kit.
Signed-off-by: Jamie Gibbons <jamie.gibbons@microchip.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
The commit d92fdb6067 ("binman: Add option for pointing to separate
description") added support for separating binman description to own file
not the be the part of DT for OS.
The main reason is that binman is not passing dt schema validation that's
why want to keep it separated.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Acked-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Increase Icicle's SYS_BOOTM_LEN to 0x4000000 which is the new default
value.
Done on Conor Dooley's request.
Signed-off-by: Martin Herren <sputnik@on-the-web.ch>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Remove CONFIG_SYS_BOOTM_LEN from all riscv defconfigs where the new
default value is used.
Signed-off-by: Martin Herren <sputnik@on-the-web.ch>
Acked-by: Michal Simek <michal.simek@amd.com> # xilinx_mbv
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
For all riscv defconfigs that use the current default value.
This is done in provision of changing the default value to the most
common used value of 0x4000000.
Signed-off-by: Martin Herren <sputnik@on-the-web.ch>
Acked-by: Michal Simek <michal.simek@amd.com> # xilinx_mbv
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
58e9502e6 "arm: sunxi: Enable SPL/SPI boot for Olinuxino Lime2-eMMC
boards" enabled SPI boot for the eMMC variant. Olimex offers the
"s16MB" variant with SPI flash populated but without eMMC populated.
Tested on board rev L.
Signed-off-by: Eric Anderson <ejona86@gmail.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
The pinecube has an ethernet connector which uses the EMAC and internal
PHY of the chip. Enable it in the config.
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
The first of the two Ethernet controllers in the Allwinner A527/T527 is
compatible to the MAC from the previous SoCs. Consequently the recent DT
update brought use the MAC node, using the A64 compatible string as the
fallback, which works out of the box.
Enable the sun8i-emac Ethernet driver in the defconfig for the Radxa and
the Avaota boards, so that kernels and other data can be loaded via
TFTP. Please note that only one of the Ethernet sockets will work, the
second MAC is not compatible, and needs a new U-Boot driver. The
X96QPro+ TV box unfortunately uses only this second EMAC, so Ethernet
cannot be used there at the moment.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
The V3s (using co-packaged DRAM) runs at 360 MHz, which is specified in
the common platform Kconfig file. However the value for MACH_SUN8I will
be picked up instead due to ordering.
Re-order the defaults to have MACH_SUN8I_V3S before MACH_SUN8I and let
it select the correct default. Also update the LicheePi Zero Dock
defconfig to remove the value, which is now correctly selected.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
There is nothing special for u-boot in the V3/V3s device-tree files,
they are just copies of the upstream ones.
Remove the copies and switch to OF_UPSTREAM for supported boards.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Allows run-time control over watchdog auto-start and the timeout via
setting the environment variable watchdog_timeout_ms. A value of zero
means "do not start". Use CONFIG_WATCHDOG_TIMEOUT_MSECS as initial value.
Users can enable the watchdog to monitor the boot process until userspace
or OS takes over to serve the watchdog.
Signed-off-by: Wadim Egorov <w.egorov@phytec.de>
Allows run-time control over watchdog auto-start and the timeout via
setting the environment variable watchdog_timeout_ms. A value of zero
means "do not start". Use CONFIG_WATCHDOG_TIMEOUT_MSECS as initial value.
Users can enable the watchdog to monitor the boot process until userspace
or OS takes over to serve the watchdog.
Signed-off-by: Wadim Egorov <w.egorov@phytec.de>
Allows run-time control over watchdog auto-start and the timeout via
setting the environment variable watchdog_timeout_ms. A value of zero
means "do not start". Use CONFIG_WATCHDOG_TIMEOUT_MSECS as initial value.
Users can enable the watchdog to monitor the boot process until userspace
or OS takes over to serve the watchdog.
Signed-off-by: Wadim Egorov <w.egorov@phytec.de>
This pull request introduces initial U-Boot support for Agilex7 M-series, along
with several enhancements and cleanups across existing Agilex platforms. Key
changes include new board support, DDR driver additions, updated device trees,
and broader SoCFPGA SPL improvements.
Highlights:
- Agilex7 M-series bring-up:
- Basic DT support and board initialization for Agilex7 M-series SoC and
SoCDK.
- New sdram_agilex7m DDR driver with UIBSSM mailbox support and HBM support.
- Clock driver support for Agilex7 M-series.
- New defconfig: socfpga_agilex7m_defconfig.
- Agilex and Agilex5 enhancements:
- Improved SPL support: ASYNC interrupt enabling, system manager init
refactor, and cold scratch register usage.
- Updated firewall probing and watchdog support in SPL.
- Cleaned up DDR code, added secure region support for ATF, and improved warm
reset handling.
- Device Tree and config updates:
- Migration to upstream Linux DT layout for Agilex platforms.
- Consolidated socfpga_agilex_defconfig and removed deprecated configs.
- Platform-specific environment variables for Distro Boot added.
- Driver fixes and cleanups:
- dwc_eth_xgmac and clk-agilex cleanup and improvements.
- Several coverity and style fixes.
Contributions in this PR are from Alif Zakuan Yuslaimi, Tingting Meng, and
Andrew Goodbody. This patch set has been tested on Agilex 5 devkit, Agilex
devkit and Agilex7m devkit.
Passing all pipeline tests at SoCFPGA U-boot custodian
https://source.denx.de/u-boot/custodians/u-boot-socfpga/-/pipelines/27318
Migrate the legacy Agilex platform to use the upstream Linux device tree
configuration. This helps reduce maintenance overhead and aligns U-Boot
with the Linux kernel's DTS hierarchy and naming conventions.
This change improves consistency between U-Boot and Linux by removing
custom/legacy DTS handling and instead relying on the standardized
definitions provided by the upstream Linux DTS.
Signed-off-by: Tingting Meng <tingting.meng@altera.com>
Signed-off-by: Alif Zakuan Yuslaimi <alif.zakuan.yuslaimi@altera.com>
Reviewed-by: Tien Fong Chee <tien.fong.chee@altera.com>
Combine all MMC, NAND and QSPI configs into single defconfig which is named
as "socfpga_agilex_defconfig". This will be the default defconfig to use.
It supports booting from all three flashes using ARM Trusted Firmware (ATF)
as the secure runtime monitor.
Signed-off-by: Alif Zakuan Yuslaimi <alif.zakuan.yuslaimi@altera.com>
Reviewed-by: Tien Fong Chee <tien.fong.chee@altera.com>
Various fixes for smatch warnings, the i2c one might be also coming in
via Heiko / I2C tree, let me know if there is conflict.
There is also W77Q51NW SPI NOR ID support, with the DT portion omitted
for now.
Enable support for Winbond SPI NOR on Retronix R-Car V4H Sparrow Hawk board,
this is required to support W77Q51NW on new board revision EVTB1 operational.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
The Galaxy R (GT-I9103) and Captivate Glide (SGH-i927) are both Tegra 2
based Samsung smartphones released in 2011. They both feature 1 GB of RAM
and 8 GB of expandable flash memory. The key difference is that the
Captivate Glide has an OLED panel (contrary to LCD in Galaxy R) and a
QWERTY keyboard in form factor of a slider.
Signed-off-by: Ion Agorria <ion@agorria.com>
Reviewed-by: Svyatoslav Ryhel <clamor95@gmail.com>
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
The Pegatron Chagall (originally built by Pegatron, but later rebranded by
other vendors under names Fujitsu Stylistic M532, Olivetti Olipad 3,
Siragon 4N, Realpad Bunaken, DNS AirTab P110w / P110g etc) is a mostly
business-oriented tablet sold in 2012 in different variants, mostly in
Europe, with slight differences in storage size (16GB/32GB) and presence
of built-in cellular modem.
Tested-by: Raffaele Tranquillini <raffaele.tranquillini@gmail.com>
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
CI: https://source.denx.de/u-boot/custodians/u-boot-stm/-/pipelines/27236
- Add support for STM32 TIMERS and STM32 PWM on STM32MP25
- Add STM32MP13xx SPL and OpTee-OS start support
- Fix header misuse in stm32 reset drivers
- Fix STMicroelectronics spelling
- Fix clk-stm32h7 wrong macros used in register read
- Fix PRE_CON_BUF_ADDR on STM32MP13
- Fix clock identifier passed to struct scmi_clk_parent_set_in
- Fix stm32 reset for STM32F4/F7 and H7
- Enable OF_UPSTREAM_BUILD_VENDOR for stm32mp13_defconfig
- Add STM32MP23 SoC and stm32mp235f-dk board support
This pull request includes updates for the SoCFPGA platform intended for the 2025.10 release
cycle. The highlights focus on enabling the Power Manager for Agilex5, NAND boot support
enhancements, and various bug fixes and cleanups across SoCFPGA components.
CI:
* https://source.denx.de/u-boot/custodians/u-boot-socfpga/-/pipelines/27221
Summary of changes:
Agilex5 Power Manager:
* Initial driver support and DT bindings are added for the Agilex5 Power Manager, enabling
better power domain control.
NAND Boot Support for Agilex5:
* SPL support for NAND boot is enabled.
* UBI/UBIFS support is configured in defconfigs.
* Memory layout updates (malloc and BSS relocation) ensure proper boot behavior.
Code Quality Improvements:
* Coverity and runtime bug fixes (e.g., jtag_usercode check, sub-device conditionals).
* Several cleanup patches addressing formatting, logic, and initialization issues.
General Maintenance:
* SPDX license tags and header include fixes.
* Device tree updates to limit SPI clock frequency and other minor adjustments.
These contributions come from Alif Zakuan Yuslaimi, Andrew Goodbody, Dinesh Maniyam, Naresh
Kumar Ravulapalli, and Tingting Meng.
This patch set has been tested on Agilex 5 devkit.
Quentin Schulz <foss+uboot@0leil.net> says:
Due to updates to the Device Tree (migrating to onboard USB hub nodes
instead of (badly) hacking things with a gpio regulator that doesn't
actually work properly), we now need to enable the onboard USB hub
driver in U-Boot.
This anticipates upcoming breakage when 6.16 DT will be merged into
U-Boot's dts/upstream.
The series can be applied as is before v6.16 DT is merged or only the
defconfig changes after 6.16 DT has been merged.
The last two patches are simply to avoid probing devices that aren't
actually routed on RK3399 Puma, which is nice to have but doesn't fix
anything.
Note that this depends on the following series:
https://lore.kernel.org/u-boot/20250722-usb_onboard_hub_cypress_hx3-v4-0-91c3ee958c0e@thaumatec.com/
Link: https://lore.kernel.org/r/20250730-puma-usb-cypress-v1-0-b1c203c733f9@cherry.de
