This board does not have any NVMe slot, so disable unneeded
CONFIG_NVME_PCI option.
Fixes: bf4a33e725 ("board: rockchip: add FriendlyElec NanoPi R3S")
Signed-off-by: Tianling Shen <cnsztl@gmail.com>
Reviewed-by: Quentin Schulz <quentin.schulz@cherry.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
BootROM leave GPIO4_D6 configured as SDMMC_PWREN function and DW MMC
driver set PWREN high in dwmci_init().
However, HW revision prior to v1.2 must pull GPIO4_D6 low to access
sdmmc. For HW revision v1.2 the state of GPIO4_D6 has no impact.
Upstream Linux commit 26c100232b09 "arm64: dts: rockchip: Fix sdmmc
access on rk3308-rock-s0 v1.1 boards" fixed this issue by adding a
vcc_sd regulator.
Include the new vcc_sd regulator in SPL and enable required Kconfig
options to set GPIO4_D6 low to fix reading sdmmc on v1.1 hw revision.
Fixes: 25438c40a0 ("board: rockchip: Add Radxa ROCK S0")
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Quentin Schulz <quentin.schulz@cherry.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The CONFIG_DEFAULT_FDT_FILE should be imx8mq_evk.dtb for this board
Fixes: 7050bd925f ("imx: imx8mq_evk: Switch to BOOTSTD")
Reported-by: Ludwig Nussel <ludwig.nussel@siemens.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Branch contains bringup of Acer Iconia Tab A500 (codename picasso), a
Tegra 2 Android device with decent Linux kernel support. Ondevice tests
and U-Boot test suit all passed.
Use LwIP network stack and enable wget HTTP command. The tftpput command
is not currently supported by LwIP network stack so remove it.
Signed-off-by: E Shattow <e@freeshell.de>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Variable $fdtfile needs to be set for automatically loading a device-tree
from the ESP or boot partition.
* Set CONFIG_DEFAULT_FDT_FILE in the defconfig.
* Add $fdtfile to the default environment.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
The device tree for rk3036 combined is now
available in the /dts/upstream directory.
Use imply OF_UPSTREAM to migrate all rk3036 boards.
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
The PP1500 and PP3000 power rails must be on very early for the U-Boot
TPL banner to be shown on debug UART.
Enable TPL_GPIO Kconfig option for bob and kevin to allow use of
spl_gpio.h functions in TPL.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The Acer Iconia A500 is a tablet computer designed, developed and
marketed by Acer Inc. It is powered by 1 GHz Nvidia Tegra 2 processor
and 1GB DDR2 RAM. The A500 is sold with 64 GB, although both 16 GB
and 32 GB models are available.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
u-boot-dfu-20250211:
CI:
- https://source.denx.de/u-boot/custodians/u-boot-dfu/-/pipelines/24556
Android:
- Handle boot images with missing DTB
Usb gadget:
- Fix nullptr in g_dnl when serial# is unset
- Add missing schedule() in f_mass_storage gadget
- Add support for STih407 in dwc3-generic
- Fix usb clocks on STih407
- Migrate STih407 to DM_USB_GADGET
Since commit 6aa8bde878 ("usb: host: ehci-generic: Remove DM_REGULATOR
flag") device_get_supply_regulator() returns -ENOSYS which is not handle
by ehci_enable_vbus_supply() and thus, ehci_usb_probe() return an error.
By enabling DM_REGULATOR flag, device_get_supply_regulator() return -ENOENT
which is handle and ehci_usb_probe() return 0.
This fixed the following issue:
stih410-b2260 =>usb start
starting USB...
Bus dwc3@9900000: Register 2000240 NbrPorts 2
Starting the controller
USB XHCI 1.00
Bus usb@9a03c00: USB OHCI 1.0
Bus usb@9a03e00: probe failed, error -38
Bus usb@9a83c00: USB OHCI 1.0
Bus usb@9a83e00: probe failed, error -38
scanning bus dwc3@9900000 for devices... 1 USB Device(s) found
scanning bus usb@9a03c00 for devices... data abort
pc : [<7df929b4>] lr : [<7df92918>]
reloc pc : [<7d6409b4>] lr : [<7d640918>]
sp : 7c73b848 ip : 9cf13c5c fp : 7c879d08
r10: 7c85d040 r9 : 7c74ded0 r8 : 09a03c00
r7 : 00000002 r6 : 7c85d080 r5 : 7c86a040 r4 : 00000000
r3 : 00000000 r2 : 00000000 r1 : 7c85d080 r0 : 7c85d040
Flags: nzCv IRQs off FIQs off Mode SVC_32
Code: 05853ae4 0affffe2 e59a2010 e59a300c (e5832010)
Resetting CPU ...
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Marek Vasut <marex@denx.de>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Link: https://lore.kernel.org/r/20250130163547.512990-3-patrice.chotard@foss.st.com
Signed-off-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Judith Mendez <jm@ti.com> says:
This patch series enables ESM reset configuration in board_init_f
for am62x and am62px devices.
This is necessary in order for error events to reset the system.
This patches are tested using watchdog to reset the system via ESM.
Link: https://lore.kernel.org/r/20250129234403.574766-1-jm@ti.com
Enable CONFIG_SPL_DRIVERS_MISC, CONFIG_SPL_MISC, CONFIG_ESM_K3
to probe the Main ESM and MCU ESM nodes.
Signed-off-by: Santhosh Kumar K <s-k6@ti.com>
Signed-off-by: Judith Mendez <jm@ti.com>
Siddharth Vadapalli <s-vadapalli@ti.com> says:
Hello,
This series re-enables MUX_MMIO at U-Boot proper on J721E and J7200
SoCs. The commits which introduced support for Hyperflash boot on both
of these SoCs disabled MUX_MMIO functionality at U-Boot proper, thereby
introducing a regression.
Series is based on commit
2b1c8d3b2d cmd: Fix Kconfig coding style
of the master branch of U-Boot.
Link: https://lore.kernel.org/r/20250201091809.1894892-1-s-vadapalli@ti.com
Commit under Fixes introduced support for Hyperflash boot but also disabled
MUX_MMIO support at U-Boot proper. MUX_MMIO is required at U-Boot proper
to setup the SERDES Lane Mapping as described by the device-tree. On J7200
SoC, PCIe functionality is broken since commit under fixes.
Fix this regression by re-enabling MUX_MMIO.
Fixes: 038f6faea9 ("configs: j7200_evm_*_defconfig: Add configs for Hyperflash boot")
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Reviewed-by: Anurag Dutta <a-dutta@ti.com>
Commit under Fixes introduced support for Hyperflash boot but also disabled
MUX_MMIO support at U-Boot proper. MUX_MMIO is required at U-Boot proper
to setup the SERDES Lane Mapping as described by the device-tree.
Fix this regression by re-enabling MUX_MMIO.
Fixes: fd7fcd4098 ("configs: j721e_evm_*_defconfig: Add configs for Hyperflash boot")
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Enable configs required for detecting and fixing up for different RAM variants.
Also resync after savedefconfig.
Signed-off-by: Wadim Egorov <w.egorov@phytec.de>
Tested-by: Daniel Schultz <d.schultz@phytec.de>
AM62x BOOTM_LEN is too small to contain OS images. Removing this sets the
size to a default 0x4000000 (for all arm64 devices).
It is unnecessary to specifically call the default size for the other
configs.
Signed-off-by: Kamlesh Gurudasani <kamlesh@ti.com>
Signed-off-by: Aashvij Shenai <a-shenai@ti.com>
The mini u-boot is hanging because of an initial stack
pointer address is used at half of the memory, when mini
u-boot is called reloc_fdt() function and doing memcpy()
for the fdt before relocation, and there is no sufficient
memory for the stack pointer. To fix, set an initial stack
pointer address to near the top of memory. The new stack
pointer address is assigned before calling the relocate
of u-boot based on the stack relocate calculation and
this new stack pointer is used while executing u-boot
from the relocated memory.
Signed-off-by: Padmarao Begari <padmarao.begari@amd.com>
Link: https://lore.kernel.org/r/20250203090409.844403-1-padmarao.begari@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Enable Standard Boot on E850-96 as documented in [1]. Along with
corresponding changes in the default environment and properly prepared
eMMC partitions (ESP and rootfs), it makes it possible to boot Debian
rootfs automatically. All boot methods were tested: efi_mgr, efi,
syslinux and script. The preferred boot method is efi_mgr, which relies
on the configured EFI variables (stored in /ubootefi.var file on ESP
partition), which boots either GRUB from /EFI/debian/grubaa64.efi, or
systemd-boot from /EFI/BOOT/BOOTAA64.EFI. Currently used boot sequence:
U-Boot -> bootcmd -> 'bootflow scan -lb' -> efi_mgr -> GRUB -> Debian
[1] doc/develop/bootstd/overview.rst
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Store U-Boot environment in BOOT2 HW area of eMMC (/dev/mmcblk0boot1),
as it's currently unused. BOOT1 area will be probably used for storing
low-level bootloaders further, so let's not touch it.
Both primary and redundant environments work fine:
=> env default -f -a
## Resetting to default environment
=> env save
Saving Environment to MMC... Writing to redundant MMC(0)... OK
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
The E850-96 default environment is going to be updated soon, requiring
next config options to be enabled:
- CONFIG_DEFAULT_FDT_FILE: $fdtfile will use this value
- CONFIG_PARTITION_TYPE_GUID: $partitions will rely on "type" feature
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
As this fragment turns off MMC in both SPL and full U-Boot, we can turn
the whole symbol off rather than just the MMC driver.
Signed-off-by: Tom Rini <trini@konsulko.com>
STM32 MPU:
- Remove dt-bindings headers available in dts/upstream
- Fixes for stm32prog
- Enable CONFIG_SYS_64BIT_LBA for STM32MP15/13/25 defconfigs
- Add upport of ck_usbo_48m in pre-reloc stage for STM32MP13
- Clean env_get_location() for STM32MP1
- Fix board_get_usable_ram_top() to fix infinite loop in cache
management for STM32MP2.
- Fix ck_flexgen_08 frequency for STM32MP2
STM32 MCU:
- Tune CYCLIC_MAX_CPU_TIME_US to avoid cyclic warning for STM32F469-Disco
- Tune CYCLIC_MAX_CPU_TIME_US to avoid cyclic warning for STM32F769-Disco
Updating the framebuffer takes quite a long time on this slow patform,
set CYCLIC_MAX_CPU_TIME_US to 50000 for stm32f469-disco to avoid
following cyclic warning:
"cyclic function video_init took too long: 46784us vs 5000us max"
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Updating the framebuffer takes quite a long time on this slow patform,
set CYCLIC_MAX_CPU_TIME_US to 8000 for stm32f769-disco to avoid
following cyclic warning:
"cyclic function video_init took too long: 7280us vs 5000us max"
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
In arch/arm/mach-stm32mp/cmd_stm32prog/stm32prog.c, in init_device(),
in case of RAW_IMAGE, part->size = block_dev->lba * block_dev->blksz.
_ part->size is declared as u64.
_ block_dev->lba is declared as lbaint_t which is uint64_t
if CONFIG_SYS_64BIT_LBA is enable, otherwise ulong.
_ block_dev->blksz is declared as unsigned long.
For example, in case block_dev->lba = 0x1dacc00, block_dev->blksz = 0x200
then part->size 0x5980000 which is incorrect as both are declared as ulong.
To fix this overflow issue, enable CONFIG_SYS_64BIT_LBA, block_dev->lba is
then declared as uint64_t and part->size get the correct value 0x3b5980000.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
In arch/arm/mach-stm32mp/cmd_stm32prog/stm32prog.c, in init_device(),
in case of RAW_IMAGE, part->size = block_dev->lba * block_dev->blksz.
_ part->size is declared as u64.
_ block_dev->lba is declared as lbaint_t which is uint64_t
if CONFIG_SYS_64BIT_LBA is enable, otherwise ulong.
_ block_dev->blksz is declared as unsigned long.
For example, in case block_dev->lba = 0x1dacc00, block_dev->blksz = 0x200
then part->size 0x5980000 which is incorrect as both are declared as ulong.
To fix this overflow issue, enable CONFIG_SYS_64BIT_LBA, block_dev->lba is
then declared as uint64_t and part->size get the correct value 0x3b5980000.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
In arch/arm/mach-stm32mp/cmd_stm32prog/stm32prog.c, in init_device(),
in case of RAW_IMAGE, part->size = block_dev->lba * block_dev->blksz.
_ part->size is declared as u64.
_ block_dev->lba is declared as lbaint_t which is uint64_t
if CONFIG_SYS_64BIT_LBA is enable, otherwise ulong.
_ block_dev->blksz is declared as unsigned long.
For example, in case block_dev->lba = 0x1dacc00, block_dev->blksz = 0x200
then part->size 0x5980000 which is incorrect as both are declared as ulong.
To fix this overflow issue, enable CONFIG_SYS_64BIT_LBA, block_dev->lba is
then declared as uint64_t and part->size get the correct value 0x3b5980000.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Weijie Gao <weijie.gao@mediatek.com> says:
This patch series add support for MediaTek MT7987 SoC with its reference
boards and related drivers.
This patch series add basic boot support on eMMC/SD/SPI-NOR/SPI-NAND for these
boards. The clock, pinctrl drivers and the SoC initializaton code are also
included.
Link: https://lore.kernel.org/r/cover.1737621362.git.weijie.gao@mediatek.com
This patch adds general board files based on MT7987 SoC.
MT7987 uses one mmc controller for booting from both SD and eMMC, and the
pins of mmc controller are also shared with one spi controller.
So three configs are need for these boot types:
1. mt7987_rfb_defconfig - SPI-NOR (spi2) and SPI-NAND (spi0)
2. mt7987_emmc_rfb_defconfig - eMMC + SPI-NOR (spi2)
3. mt7987_sd_rfb_defconfig - SD + SPI-NOR (spi2)
Note: spi2 also supports booting from SPI-NAND, but not the default option.
Signed-off-by: Sam Shih <sam.shih@mediatek.com>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
It seems that every remaining system which enables BITBANGMII also
enables BITBANGMII_MULTI . Remove the BITBANGMII_MULTI symbol and
assume it is always enabled. This allows removal of a bit of legacy
code. No functional change intended.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Paul Barker <paul.barker.ct@bp.renesas.com>
