Heinrich Schuchardt <heinrich.schuchardt@canonical.com> says:
To implement the EFI_SYSTEM_TABLE_POINTER we need 4 MiB aligned
memory.
On the sandbox LMB uses addresses relative to the start of a page aligned
RAM buffer allocated with mmap(). This leads to a mismatch of alignment
between EFI which uses pointers and LMB which uses phys_addr_t.
Ensure that the RAM buffer used for LMB is 4 MiB aligned.
Provide a unit test for efi_alloc_aligned_pages() verifying this alignment.
Do not overwrite RAM size in dram_init().
Link: https://lore.kernel.org/r/20250608075428.32631-1-heinrich.schuchardt@canonical.com
To implement the EFI_SYSTEM_TABLE_POINTER we need 4 MiB aligned
memory.
On the sandbox LMB uses addresses relative to the start of a page aligned
RAM buffer allocated with mmap(). This leads to a mismatch of alignment
between EFI which uses pointers and LMB which uses phys_addr_t.
Ensure that the RAM buffer used for LMB is 4 MiB aligned.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Rename the variable and add ENV_ prefix, so that all configuration
options which are related to environment would have an CONFIG_ENV_
prefix. No functional change.
Use ENV_MMC_DEVICE_INDEX to clarify this is the SD/MMC device
index, a number, as enumerated by U-Boot. Update the help text
accordingly.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Instead of using defines for the RAM size and base address, retrieve these
information from the devicetree.
This aligns with the sama5d27_som1_ek board in commit 73c1589f02
("board: sama5d27_som1_ek: Get dram size and base from device tree").
While at it, remove a spurious '/* SPL */' comment.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Add Retronix R-Car V4H Sparrow Hawk board based on Renesas R-Car V4H ES3.0
(R8A779G3) SoC. This is a single-board computer with single gigabit ethernet,
DSI-to-eDP bridge, DSI and two CSI2 interfaces, audio codec, two CANFD ports,
micro SD card slot, USB PD supply, USB 3.0 ports, M.2 Key-M slot for NVMe SSD,
debug UART and JTAG.
DT is imported from Linux next commit:
a719915e76f2 ("arm64: dts: renesas: r8a779g3: Add Retronix R-Car V4H Sparrow Hawk board support")
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Tom Rini <trini@konsulko.com> says:
In a private thread, Simon asked about what's needed to get PowerPC
migrated to DM_SERIAL. I went and took a look, and to complete the
entire DM_SERIAL migration (excluding SPL/TPL) we're actually nearly
there. This series first migrates PowerPC (and some NXP Layerscape
boards that share history more clearly with PowerPC parts), with the
biggest change being to make sure we still use the correct legacy
drivers in SPL/TPL (where SPL is extremely constrained). With that out
of the way, I looked at what was left. With two exceptions, it's
platforms which can be trivially enabled for conversion, and so we do
that.
Link: https://lore.kernel.org/r/20250502201226.1369013-1-trini@konsulko.com
Migrate the few ARM Layerscape platforms that had not been switched
along with all remaining PowerPC platforms to DM_SERIAL. For PowerPC,
this means that platforms which use SPL/TPL, keeping the non-DM serial
driver enabled there as they do not use DM. We also rework the guards
on how to define CFG_SYS_NS16550_CLK so that this is mostly in one place
now.
Signed-off-by: Tom Rini <trini@konsulko.com>
The BROM of TH1520 always initializes UART0's parent clock and
configures the baudrate to 115200. Describe the clock frequency to make
UART function correctly in SPL without introducing CCF.
Signed-off-by: Yao Zi <ziyao@disroot.org>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Move unnecessary clock frequency assignment out of device-tree and into the
board config header so that the ns16550 serial driver can successfully init
during SPL after failing to resolve the parent clock from upstream dts. The
serial driver will then resolve clock frequency from device-tree node parent
clock at init during Main app as it is expected by upstream.
Signed-off-by: E Shattow <e@freeshell.de>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Loading a FIT image for kernel, initrd and rootfs on px30 can result in an
memory overlap, resulting in the not 100% helpful message of
"This will not be a case any time" from lmb_fix_over_lap_regions().
Adding a bit of debug info to lmb_fix_over_lap_regions() brings:
lmb_fix_over_lap_regions: base1 0x280000-0x6005ac > base2 0x600000-0x6000d1
So this is because the FIT image gets loaded to the kernel_addr_r at
0x280000 while the pxe-file is already living at 0x600000, only 3.5MB
behind.
In commit 4acc8bb044 ("configs: rockchip: sync ENV_MEM_LAYOUT_SETTINGS
for rk3308, rk3328, and rk3399") FUKAUMI Naoki already brought the memory
layouts for the mentioned socs in sync.
Adjusting the env-layout on px30 to this scheme, magically solves the
overlap issue and also brings px30 more in line with the other mentioned
SoCs.
Signed-off-by: Heiko Stuebner <heiko.stuebner@cherry.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
For the STM32MP15 DHSOM, change the default environment so an AB schema
on a device can be detected.
For this the define "SCAN_DEV_FOR_BOOT_PARTS" is overwritten and
appended.
The detection works by looking for the partitions with specific lables.
The name of those partitions are in the variables and its defaults:
* dh_ab_partname_primary=rootfs-a
* dh_ab_partname_secondary=rootfs-b
To prevent being hanging at bootcmd, enable "CONFIG_BOOT_RETRY" and
"CONFIG_RESET_TO_RETRY", but the timer will only be activated, if the AB
partitions are detected.
Signed-off-by: Pascal Zimmermann <pzimmermann@dh-electronics.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
This patch adds i.MX95 19x19 EVK board basic support.
Messaging unit for EdgeLock Secure Enclave, messaging unit for System
Manager, uSDHC for SD Card, gpio, lpuart are supported now.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Alice Guo <alice.guo@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
SeeedStudio BeagleBone Green Eco (BBGE) is a clone of the BeagleBone Green
(BBG). It has minor differences from the BBG, such as a different PMIC,
a different Ethernet PHY, and a larger eMMC.
The PMIC is not yet supported in mainline, but the work is ongoing.
Signed-off-by: Kory Maincent <kory.maincent@bootlin.com>
enable text based default U-Boot Environment by enabling
CONFIG_ENV_SOURCE_FILE
and adding default environment file:
board/siemens/capricorn/capricorn_cxg3.env
Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Walter Schweizer <walter.schweizer@siemens.com>
Add support for booting from USB pen drive, since USB host
port is available on the STM32MP2.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
For nor0 boot for the STMicroelectronics boards, the bootfs
is found in SD-Card = mmc0 for nor0 boot.
Introduce a new file configuration file stm32mp25_st_common.h
to manage this specific behavior for the STMicroelectronics
boards; change the boot order for nor0 boot and don't use
the default DISTRO order define in BOOT_TARGET_DEVICES:
mmc1, ubifs, mmc0, mmc2.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Signed-off-by: Patrice CHOTARD <patrice.chotard@foss.st.com>
Add support of UBI boot and activate the needed
configuration for U-Boot environment in UBI volume for
NAND or in a MTD partition for NOR device, SPI Flash:
ENV_OFFSET, ENV_OFFSET_REDUND, ENV_SECT_SIZE is
aligned with the default MTD partition on NOR device
of the STMicroelectronics boards.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Handle boot for the 3 instance of MMC and call the command stm32prog
for serial boot on USB or on UART as it is done for other STM32MP platform.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Enable OF_UPSTREAM flag for STM32F7 platforms.
Use upstream device tree for DSI and LTDC nodes,
As now in upstream DT, in panel@0 node, power-supply property is
present, which is a fixed-regulator, add DM_REGULATOR_FIXED flag
for stm32f769-disco boards.
Set also DEFAULT_FDT_FILE in defconfigs and use it in stm32f746-disco.h
to indicate which FDT file to load (All STM32F7 boards are using this
file).
If something is missing, it must be added in upstream device tree
in linux kernel ("px_clk" for DSI by example).
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
The ROC-RK3576-PC is a SBC made by Firefly, designed around the RK3576
SoC. This adds the needed board infrastructure and config for it.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The Rockchip RK3576 is a ARM-based SoC with quad-core Cortex-A72
and quad-core Cortex-A53 including 6TOPS NPU, Mali-G52 MC3, HDMI Out,
DP, eDP, MIPI DSI, MIPI CSI2, LPDDR4/4X/5, eMMC5.1, SD3.0/MMC4.5, UFS,
USB OTG 3.0, Type-C, USB 2.0, PCIe 2.1, SATA 3, Ethernet, SDIO3.0, I2C,
UART, SPI, GPIO and PWM.
Add arch core support for it.
Signed-off-by: Xuhui Lin <xuhui.lin@rock-chips.com>
[adapted for mainline u-boot]
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Rockchip RK3528 is a ARM-based SoC with quad-core Cortex-A53.
Add initial arch support for the RK3528 SoC.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Ensure rk3588_common.h can be used by boards directly by defining a
blank ROCKCHIP_DEVICE_SETTINGS unless it already is defined.
Add a default SYS_CONFIG_NAME to include rk3588_common.h unless a board
target overrides it in its board Kconfig.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Ensure rk3568_common.h can be used by boards directly by defining a
blank ROCKCHIP_DEVICE_SETTINGS unless it already is defined.
Add a default SYS_CONFIG_NAME to include rk3568_common.h unless a board
target overrides it in its board Kconfig.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Ensure ROCKCHIP_DEVICE_SETTINGS is defined before including
rk3588_common.h in board include/configs files.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Ensure ROCKCHIP_DEVICE_SETTINGS is defined before including
rk3568_common.h in board include/configs files.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The partitions env variable is using an outdated partition layout that
is typically expected to be used with older vendor miniloader blobs.
Rockchip devices will run fine using any partition layout if the first
16 MiB of MMC storage is ignored/skipped.
Remove the partitions env variable to stop encourage users a continued
use of this outdated partition layout on RK3588 devices.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The partitions env variable is using an outdated partition layout that
is typically expected to be used with older vendor miniloader blobs.
Rockchip devices will run fine using any partition layout if the first
16 MiB of MMC storage is ignored/skipped.
Remove the partitions env variable to stop encourage users a continued
use of this outdated partition layout on RK356x devices.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
In order to be able to use Device Tree Overlays, the fdtoverlay_addr_r
needs to be specified.
Follow what's been done for other Rockchip SoCs and leave 1MiB for the
base DTB before the address for the overlay.
Signed-off-by: Quentin Schulz <quentin.schulz@cherry.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
