Simon Glass <sjg@chromium.org> says:
When the SPL build-phase was first created it was designed to solve a
particular problem (the need to init SDRAM so that U-Boot proper could
be loaded). It has since expanded to become an important part of U-Boot,
with three phases now present: TPL, VPL and SPL
Due to this history, the term 'SPL' is used to mean both a particular
phase (the one before U-Boot proper) and all the non-proper phases.
This has become confusing.
For a similar reason CONFIG_SPL_BUILD is set to 'y' for all 'SPL'
phases, not just SPL. So code which can only be compiled for actual SPL,
for example, must use something like this:
#if defined(CONFIG_SPL_BUILD) && !defined(CONFIG_TPL_BUILD)
In Makefiles we have similar issues. SPL_ has been used as a variable
which expands to either SPL_ or nothing, to chose between options like
CONFIG_BLK and CONFIG_SPL_BLK. When TPL appeared, a new SPL_TPL variable
was created which expanded to 'SPL_', 'TPL_' or nothing. Later it was
updated to support 'VPL_' as well.
This series starts a change in terminology and usage to resolve the
above issues:
- The word 'xPL' is used instead of 'SPL' to mean a non-proper build
- A new CONFIG_XPL_BUILD define indicates that the current build is an
'xPL' build
- The existing CONFIG_SPL_BUILD is changed to mean SPL; it is not now
defined for TPL and VPL phases
- The existing SPL_ Makefile variable is renamed to SPL_
- The existing SPL_TPL Makefile variable is renamed to PHASE_
It should be noted that xpl_phase() can generally be used instead of
the above CONFIGs without a code-space or run-time penalty.
This series does not attempt to convert all of U-Boot to use this new
terminology but it makes a start. In particular, renaming spl.h and
common/spl seems like a bridge too far at this point.
The series is fully bisectable. It has also been checked to ensure there
are no code-size changes on any commit.
Oliver Gaskell <Oliver.Gaskell@analog.com> says:
ADSP-SC5xx is a series of ARM-based DSPs.
This comprises the armv7 based SC57x, SC58x and SC594 series, and the
armv8 based SC598.
This patch series includes configurations, init code, and minimal DTs
to enable Analog Devices' evaluation boards for these SoCs to boot
through SPL and into U-Boot Proper, as well as devicetree schemas for
the added DTs.
This patch series depends on ("arm: Add Analog Devices SC5xx Machine
Type") (https://lists.denx.de/pipermail/u-boot/2024-April/552043.html)
Adds support for Analog Devices' SC589-EZKIT board. Includes:
- Board specific configs in mach-sc5xx/Kconfig
- Board-specific Kconfig and environment in board/adi/
- Memory configuration
Signed-off-by: Oliver Gaskell <Oliver.Gaskell@analog.com>
Add support for the Comvetia i.MX6Q LXR2 board, which is
uses the Phytec PFLA02 SoM.
Based on the original work from Stefano Babic <sbabic@denx.de>.
The Phytec PFLA02 devicetrees are taken from kernel 6.11-rc7.
The imx6q-lxr.dts has been submitted upstream:
https://lore.kernel.org/linux-devicetree/20240913200906.1753458-3-festevam@gmail.com/
After it gets accepted in mainline (most likely in kernel 6.13),
the lxr2 board can then be switched to OF_UPSTREAM and these device trees
can be removed from U-Boot.
Signed-off-by: Fabio Estevam <festevam@denx.de>
AST2700 SoCs integrates a Ibex 32-bits RISC-V core as the boot MCU
for the first stage bootloader execution, namely SPL.
This patch implements the preliminary base to successfully run SPL
on this RV32-based MCU to the console banner message.
Signed-off-by: Chia-Wei Wang <chiawei_wang@aspeedtech.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
As per the maintainers at egnite GmbH, they are no longer interested in
supporting this board. Go and remove the platform here. Furthermore,
this is the only AT91SAM9XE platform in-tree so remove supporting code
for that as well.
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
The definition of CFG_MXC_USB_PORTSC as (PORT_PTS_UTMI | PORT_PTS_PTW)
can be removed from mx5/mx6/mx7/mx8m board config files as it is the
default in drivers/usb/host/ehci-mx5.c and drivers/usb/host/ehci-mx6.c.
Suggested-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Tim Harvey <tharvey@gateworks.com>
CFG_MXC_USB_FLAGS is only used for drivers/usb/host/ehci-mx5.c, so it
can be removed from all the imx6/imx7/imx8m board config files.
mx51evk.h is the only place CFG_MXC_USB_FLAGS is not set to 0.
Suggested-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
The SD card is registered as mmc device 0.
Fix it accordingly so that the board can boot to Linux
from the SD card.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Remove several comments that do not apply anymore to
the current file content.
While at it, write 'PMIC' into a single line for consistency.
Signed-off-by: Fabio Estevam <festevam@denx.de>
This command allows easy update on SD card or eMMC of the flash.bin
generated (with binman) during u-boot build.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Benjamin Hahn <B.Hahn@phytec.de>
Tested-by: Teresa Remmet <t.remmet@phytec.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Currently, the power_init_board() function is not executed because
CONFIG_POWER_LEGACY is not selected.
Convert to PMIC driver model, which allows removing board I2C code in
favor of the I2C driver model.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Only one board uses this option and it is very old. Let's drop it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
This option is very old and the migration deadline was years ago. Drop
it so that the I2C system can be simplified.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
This is used by a few boards but we are years past the migration date,
so let's drop it now.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
The Rock 5 ITX is a board in ITX form factor using the RK3588 SoC
It can be powered either by 12V, ATX power-supply or PoE.
Notable peripherals are the 4 SATA ports, M.2 M-Key slot, M.2 E-key slot,
2*2.5Gb PCIe-connected Ethernet NICs.
Display options are 2*HDMI, DP via USB-c, eDP + 2*DSI via PCB connectors.
USB ports are 4*USB3 + 2*USB2 on the back panel and 2-port front-panel
connector.
Schematics for the board can be found on
- https://dl.radxa.com/rock5/5itx/radxa_rock_5_itx_X1100_schematic.pdf
- https://dl.radxa.com/rock5/5itx/v1110/radxa_rock_5itx_v1110_schematic.pdf
The naming scheme with the dashes follows Dragan's comment on the mainline
devicetree commit:
"the name of this board deviates from the standard Radxa naming scheme,
which is something like "ROCK <number><letter>" thus, "rock-5a" is
fine, but it should be "rock-5-itx", simply because there's a space
between "5" and "ITX" in "ROCK 5 ITX"
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
This board has not been converted to CONFIG_DM_I2C by the deadline.
Remove it.
Acked-by: Robert Nelson <robertcnelson@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_I2C by the deadline.
Remove it.
Acked-by: Robert Nelson <robertcnelson@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Rework to remove use of legacy I2C API. Also switch
to DM_SERIAL to avoid board removal warning.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Troy Kisky <troy.kisky@boundarydevices.com>
Instead of cluttering up a header file with a bunch of defines,
move the default environmental variables to a file called
am3517evm.env and reference it from the defconfig. Also
remove dead comments.
Signed-off-by: Adam Ford <aford173@gmail.com>
Enable USB host as well as USB gadget and DFU support for a53 and r5
configs. Also, enable UUU fastboot support to download files with
the UUU tool from a53.
Additionally, configure usb0 to peripheral mode and add extra
environment for DFU use.
Signed-off-by: Vitor Soares <vitor.soares@toradex.com>
Reviewed-by: Francesco Dolcini <francesco.dolcini@toradex.com>
- add support for compressed kernel for rk3308
- prepare support for fdtoverlay for rk3328
tested on ROCK Pi S 256MB, ROCK Pi E 2GB, and ROCK Pi 4A 4GB with
linux-next-20240613 defconfig kernel.
Signed-off-by: FUKAUMI Naoki <naoki@radxa.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
this is cosmetic change. no functional change is intended.
- remove redundant white spaces
- replace white spaces with tab
- align position of last letter/word
- sort lines in CFG_EXTRA_ENV_SETTINGS
- add comment after #endif
Signed-off-by: FUKAUMI Naoki <naoki@radxa.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The NanoPi R6S is a SBC by FriendlyElec based on the Rockchip RK3588s.
It comes with 4GB or 8GB of RAM, a microSD card slot, 32GB eMMC storage,
one RTL8211F 1GbE and two RTL8125 2.5GbE Ethernet ports, one USB 2.0
Type-A and one USB 3.0 Type-A port, a HDMI port, a 12-pin GPIO FPC
connector, a fan connector, IR receiver as well as some buttons and LEDs.
Add initial support for this board using the upstream devicetree sources.
Kernel commit:
f1b11f43b3e9 ("arm64: dts: rockchip: Add support for NanoPi R6S")
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Sebastian Kropatsch <seb-dev@mail.de>
The NanoPi R6C is a SBC by FriendlyElec based on the Rockchip RK3588s.
It comes with 4GB or 8GB of RAM, a microSD card slot, optional 32GB eMMC
storage, one M.2 M-Key connector, one RTL8211F 1GbE and one RTL8125
2.5GbE Ethernet port, one USB 2.0 Type-A and one USB 3.0 Type-A port, a
HDMI port, a 30-pin GPIO header as well as multiple buttons and LEDs.
Add initial support for this board using the upstream devicetree sources.
Tested in U-Boot proper:
- Booting from eMMC works
- 1GbE Ethernet works using the eth_eqos driver (tested by ping)
- 2.5GbE Ethernet works using the eth_rtl8169 driver (tested by ping),
but the status LEDs on this specific port currently aren't working
- NVMe SSD in M.2 socket does get recognized (tested with `nvme scan`
followed by `nvme details`)
Kernel commit:
d5f1d7437451 ("arm64: dts: rockchip: Add support for NanoPi R6C")
Reviewed-by: Quentin Schulz <quentin.schulz@cherry.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Sebastian Kropatsch <seb-dev@mail.de>
No meaningful changes were made to this SoM since February 2021. Nobody
from Theobroma has booted anything recent on that product since July
2021 at the latest. The product isn't available to buy anymore and
disappeared from our website.
This product is therefore unmaintained and it would be disingenuous to
say the opposite, so drop support for RK3368 Lion.
If you're a user of Lion, feel free to revert this patch or contact our
sales/support department.
Signed-off-by: Quentin Schulz <quentin.schulz@cherry.de>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
- Switch to standard boot (in include/configs/ds414.h and
configs/ds414_defconfig)
- Implement board_late_init() to ensure successful enumeration
of USB3 devices
- Remove unnecessary checkboard()
- Updated IDENT_STRING to indicate this u-boot supports both Synology
DS414 and DS214+ boards
- Add SYS_THUMB_BUILD to reduce binary size
- Add NET_RANDOM_ETHADDR
- Add CONFIG_LBA48 and CONFIG_SYS_64BIT_LBA to support >2TB HDD/SDD
Signed-off-by: Tony Dinh <mibodhi@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Acked-by: Phil Sutter <phil@nwl.cc>
Marek Mojík <marek.mojik@nic.cz> says:
Hello all,
this is a continuation of previous work by Pali to add support for the
Turris 1.x board. As the patches were based on u-boot v2022.04, a
nontrivial rebasing was needed.
Some notes:
- Some options that are in SD defconfig are disabled in NOR defconfig
because over the years u-boot grew and the old NOR defconfig will not
fit into NOR memory.
- SD boot with RAM larger than 2GB will only allocate 2GB of RAM (We
were not able to fix this yet)
Add support for CZ.NIC Turris 1.x routers.
CZ.NIC Turris 1.0 (RTRS01) and 1.1 (RTRS02) are open source routers, they
have dual-core PowerPC Freescale P2020 CPU and are based on reference
Freescale P2020RDB-PC-A board design.
Hardware design is fully open source, all firmware and hardware design
files are available at Turris project website:
https://docs.turris.cz/hw/turris-1x/turris-1x/https://project.turris.cz/en/hardware.html
The P2020 BootROM can load U-Boot either from NOR flash or from SD card.
We add the new defconfigs, turris_1x_nor_defconfig, which configures
U-Boot for building the NOR image, and turris_1x_sdcard_defconfig, which
configures U-Boot for building an image suitable for SD card.
The defconfig for NOR image is stripped-down a - many config options
enabled in SD defconfig are disabled for NOR defconfig. This is because
U-Boot grew non-trivially in the last two years and it would not fit
into the space allocated for U-Boot in the NOR memory. In the future we
may try to use LTO to reduce the size of the code and enable more
options.
The design of CZ.NIC Turris 1.x routers is based on Freescale P2020RDB-PC-A
board, so some code from boards/freescale/p1_p2_rdb_pc is used and linked
into Turris 1.x board code.
Turris 1.x code in this patch uses modern distroboot and can boot Linux
kernel from various locations, including NAND, SD card, USB flash disks,
NVMe disks or SATA disks (connected to extra SATA/SCSI PCIe controllers).
Via distroboot is implemented also rescue NOR boot for factory recovery,
triggered by reset button, like on other existing Turris routers.
SD boot with RAM larger than 2GB will only allocate 2GB of RAM (We were
not able to fix this yet)
[ Because various CONFIG_ macros were migrated to Kconfig since the last
time this worked on upstream U-Boot (in 2022), a non-trivial rebasing
was needed and some issues were solved. ]
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Mojík <marek.mojik@nic.cz>
Reviewed-by: Marek Behún <kabel@kernel.org>
- Add mvebu_espressobin_ultra-88f3720_defconfig (Benjamin)
- Update DTS for Thecus N2350 board (Tony)
- Add "old" Marvell DDR3 training for Armada 38x and Turris Omnia
(Marek)
- Misc turris_omnia changes (Marek)
Currently, Armada 8k config header is setting boot devices and including
<config_distro_bootcmd.h> regardless of the CONFIG_DISTRO_DEFAULTS being
enabled or not, thus populating the environment for distro boot even on
devices that have no need for it.
So, lets simply respect the value of CONFIG_DISTRO_DEFAULTS.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Booting an initramfs with the current initrd_addr address may lead to
initramfs corruption and boot failure.
Fix the initramfs problem by applying the following layout
suggested by Tom Rini:
loadaddr=0x40480000 --> Gets moved to 0x40600000 in run-time:
Uncompressing Kernel Image
Moving Image from 0x40480000 to 0x40600000, end=41e80000
fdt_addr_r= moved loadaddr + 128 MiB = 0x48600000
initrd_addr=fdt_addr_r + 512 KiB = 0x48680000
Signed-off-by: Fabio Estevam <festevam@denx.de>
Tested-by: Stefano Babic <sbabic@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
Various minor fixes and improvements:
* Fix Qualcomm SPMI v5 support
* Move default environment to a file
* Add support for special pins (e.g ufs/mmc reset/data pins)
* IPQ moves to OF_UPSTREAM and receives some cleanup and MAINTAINERS
changes
* Add a reset driver for devices without PSCI
* msm8916 USB clock improvements for mobile devices
Make use of CONFIG_DEFAULT_ENV_FILE and move the default qcom
environment to a file under board/qualcomm.
This is much cleaner and means we don't need to recompile on changing
the environment.
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
