DW HDMI support Vendor PHY like Rockchip RK3328 Inno HDMI PHY.
Extend the vendor phy handling by adding platform phy hooks.
Signed-off-by: Jagan Teki <jagan@edgeble.ai>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
HDP is a hardware connector event, so detect the same once the
controller and attached PHY initialization are done.
Signed-off-by: Jagan Teki <jagan@edgeble.ai>
Support timing parsing from EDID if panel device tree node
provides DDC i2c bus instead of timings node.
Tested-by: Robert Eckelmann <longnoserob@gmail.com> # ASUS TF201
Tested-by: Agneli <poczt@protonmail.ch> # Toshiba AC100 T20
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
[agust: reworked to fix dm_i2c_* build errors and to big img size]
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Add support for the IMX8MM SoC by adding driver data with the compatible
string of the GPR controller.
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Add support for PCIe clocks required to enable PCIe support on
iMX8MM SoC.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Marek Vasut <marex@denx.de>
MP1:
_ Add OHCI HCD support for STM32MP15xx DHSOM
_ Report OTP-CLOSED instead of rev.? on closed STM32MP15xx
_ Initialize TAMP_SMCR BKP..PROT fields on STM32MP15xx
_ Jump to ep on successful resume in PSCI suspend code
_ Add FASTBOOT support for STM32MP13
_ Fix/Rework key and leds management for STM32MP13/15
_ net: dwc_eth_qos: Clean up STM32 glue code and add STM32MP13xx support
MP2:
_ Add stm32-fmc-ebi support
_ Add: sdmmc2 support and fix AARCH64 compilation
The "st,ext-phyclk" property is a unification of "st,eth-clk-sel"
and "st,eth-ref-clk-sel" properties. All three properties define
ETH CK clock direction, however:
- "st,eth-clk-sel" selects clock direction for GMII/RGMII mode
- "st,eth-ref-clk-sel" selects clock direction for RMII mode
- "st,ext-phyclk" selects clock direction for all RMII/GMII/RGMII modes
The "st,ext-phyclk" is the preferrable property to use.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Christophe ROULLIER <christophe.roullier@foss.st.com>
Manage 2 ethernet instances, select which instance to configure with mask
If mask is not present in DT, it is stm32mp15 platform.
Signed-off-by: Christophe Roullier <christophe.roullier@st.com>
Signed-off-by: Marek Vasut <marex@denx.de> # Rework the code
Reviewed-by: Christophe ROULLIER <christophe.roullier@foss.st.com>
Use const bool for the values parsed out of DT. Drop the duplicate
assignment of false into those bool variables, assign them directly
with the content parsed out of DT. Abbreviate the variable name too.
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Use dev_*() only to print all the logs from this glue code,
instead of mixing dev_*(), log_*(), pr_*() all in one code.
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Move the log_debug() calls on top of the bit manipulation code.
No functional change.
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Use FIELD_PREP to configure content of ETH_SEL bitfield in SYSCFG_PMCSETR
register. No functional change.
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Replace ifdef CONFIG_CLK with if (CONFIG_IS_ENABLED(CLK)) to improve code
build coverage. Some of the functions printed debug("%s: OK\n", __func__);
on exit with and without CLK enabled, some did not, make it consistent and
print nothing if CLK is disabled.
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Christophe ROULLIER <christophe.roullier@foss.st.com>
Move board_interface_eth_init() into eqos_probe_syscfg_stm32() in STM32
driver glue code. The eqos_probe_syscfg_stm32() parses STM32 specific DT
properties of this MAC and configures SYSCFG registers accordingly, there
is nothing board specific happening in this function, move it into generic
driver code instead. Drop the now unused duplicates from board files.
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Signed-off-by: Marek Vasut <marex@denx.de>
The current glue code is specific to STM32MP15xx, the upcoming STM32MP13xx
will introduce another entry specific to the STM32MP13xx. Rename the current
entry to eqos_stm32mp15_config in preparation for STM32MP13xx addition. No
functional change.
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Christophe ROULLIER <christophe.roullier@foss.st.com>
Move STM32 glue code into separate file to contain the STM32 specific
code outside of the DWMAC core code. No functional change.
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Christophe ROULLIER<christophe.roullier@foss.st.com>
FMC2 IP supports up to 4 chip select. On MP1 SoC, only 2 of them are
available when on MP25 SoC, the 4 chip select are available.
Let's use a platform data structure for parameters that will differ.
Signed-off-by: Christophe Kerello <christophe.kerello@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
The FMC2 revision 2 supports security and isolation compliant with
the Resource Isolation Framework (RIF). From RIF point of view,
the FMC2 is composed of several independent resources, listed below,
which can be assigned to different security and compartment domains:
- 0: Common FMC_CFGR register.
- 1: EBI controller for Chip Select 1.
- 2: EBI controller for Chip Select 2.
- 3: EBI controller for Chip Select 3.
- 4: EBI controller for Chip Select 4.
- 5: NAND controller.
Signed-off-by: Christophe Kerello <christophe.kerello@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Add the support of the revision 2 of FMC2 IP.
- PCSCNTR register has been removed,
- CFGR register has been added,
- the bit used to enable the IP has moved from BCR1 to CFGR,
- the timeout for CEx deassertion has moved from PCSCNTR to BCRx,
- the continuous clock enable has moved from BCR1 to CFGR,
- the clk divide ratio has moved from BCR1 to CFGR.
The MP1 SoCs have only one signal to manage all the controllers (NWAIT).
The MP25 SOC has one RNB signal for the NAND controller and one NWAIT
signal for the memory controller.
Let's use a platform data structure for parameters that will differ
between MP1 and MP25.
Signed-off-by: Christophe Kerello <christophe.kerello@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
If a button device fails to probe, it will still be added to the uclass
device list, and therefore will still be iterated over in
button_read_keys() resulting in a UAF on the buttons private data.
Resolve this by unbinding button devices that aren't active after
probing, and print a warning so it's clear that the button is broken.
Fixes: e877996289 ("dm: input: add button_kbd driver")
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Reading the boot mode from RTC memory requires a real time clock.
Add the missing Kconfig dependency.
Fixes: c74675bd90 ("reboot-mode: read the boot mode from RTC memory")
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Igor says:
"The problem initially was in the TEE sandbox driver implementation
(drivers/tee/sandbox.c) and it's limitations, which doesn't
permit to have multiple simultaneous sessions with different TAs.
This is what actually happened in this CI run [1], firstly "optee_rpmb"
cmd was executed (and after execution we had one session open), and
then "scp03", which also makes calls to OP-TEE, however it fails
in sandbox_tee_open_session() because of this check:
if (state->ta) {
printf("A session is already open\n");
return -EBUSY;
}
I had two ways in mind to address that:
1. Close a session on each optee_rpmb cmd invocation.
I don't see any reason to keep this session open, as obviously
there is no other mechanism (tbh, I don't know if DM calls ".remove" for active
devices) to close it automatically before handing over control to
Linux kernel. As a result we might end up with some orphaned sessions
registered in OP-TEE OS core (obvious resource leak).
2. Extend TEE sandbox driver, add support for multiple
simultaneous sessions just to handle the case.
I've chosen the first approach, as IMO it was "kill two birds with one stone",
I could address resource leak in OP-TEE and bypass limitations of
TEE sandbox driver."
Link: https://lore.kernel.org/u-boot/CAByghJZVRbnFUwJdgU534tvGA+DX2pArf0i7ySik=BrXgADe3Q@mail.gmail.com/
The CI https://source.denx.de/u-boot/custodians/u-boot-tpm/-/pipelines/20414
showed no problems
Set the speed requested through mpc8xx_spi_set_speed() instead
of hardcoding a fixed speed.
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
On CPM, the RISC core is a lot more efficiant when doing transfers
in 16-bits chunks than in 8-bits chunks, but unfortunately the
words need to be byte swapped.
So, for large tranfers with an even size, allocate a temporary
buffer and byte-swap data before and after transfer.
This change allows setting higher speed for transfer. For instance
on an MPC 8xx (CPM1 comms RISC processor), the documentation tells
that transfer in byte mode at 1 kbit/s uses 0.200% of CPM load
at 25 MHz while a word transfer at the same speed uses 0.032%
of CPM load. This means the speed can be 6 times higher in
word mode for the same CPM load.
For small transfers, the load reduction is not worth the CPU load
required to allocate the temporary buffer, so do it only when data
size is over 64 bytes.
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Perform multiple transfer of size MAX_BUFFER when the data to be
transferred is longer than MAX_BUFFER.
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
SDMA configuration register needs to be set up only once and doesn't
belong to drivers. Also, the value to be used is different on mpc885.
So do the init in cpu_init_f() with 0x40 for mpc885 and 0x1 for others.
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
xfer ops can be passed a NULL input or output buffer. At the
time being the driver ignores it and overwrites memory at 0.
Define a dummy buffer and use it when either input or output
buffer is NULL. Bail out when both are NULL as it shouldn't.
Also increase MAX_BUFFER len to 32k as the current is pretty
low.
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Since commit 773ad4ebb1 ("spi, mpc8xx: Add support for chipselect via
GPIO and fixups"), DM_GPIO is required for 8xx SPI.
Add the missing dependency to avoid build failures.
Fixes: 773ad4ebb1 ("spi, mpc8xx: Add support for chipselect via GPIO and fixups")
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
The usage of the common.h include file is deprecated [1], and has already
been removed from several files.
Get rid of all inclusions in the "drivers/tee" directory, and replace it
with required include files directly where needed.
[1] doc/develop/codingstyle.rst
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: Igor Opaniuk <igor.opaniuk@gmail.com>
Reviewed-by: Sam Protsenko <semen.protsenko@linaro.org>
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Currently, fastboot protocol in U-Boot has no opportunity
to execute vendor custom code with verifed boot. This patch
introduce new fastboot subcommand fastboot oem board:<cmd>,
which allow to run custom oem_board function.
Default implementation is __weak. Vendor must redefine it in
board/ folder with his own logic.
For example, some vendors have their custom nand/emmc partition
flashing or erasing. Here some typical command for such use cases:
- flashing:
$ fastboot stage bootloader.img
$ fastboot oem board:write_bootloader
- erasing:
$ fastboot oem board:erase_env
Signed-off-by: Alexey Romanov <avromanov@salutedevices.com>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Reviewed-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Link: https://lore.kernel.org/r/20240418100129.1691822-2-avromanov@salutedevices.com
Signed-off-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
CI:
https://source.denx.de/u-boot/custodians/u-boot-imx/-/pipelines/20348
- Update the imx_rgpio2p to only access one address as per the
dt-schema.
- Remove unused imx9_cpu.c file.
- Only use the LPUART ipg clk for i.MX7ULP.
- Use the correct anatop base for accessing the PLL clocks on i.MX93.
The i.MX8ULP/93 gpio dt-schema have been updated to only have one
address entry, update the driver to support it.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The value defaults to 0 and is ignored by dw_mmc code, so the other
users are not affected.
Setting this explicitly fixes some weird reading error found on Hi3798MV200.
Fixes: 8a5dc8140e ("mmc: hi6220_dw_mmc: add compatible for HC2910 support")
Signed-off-by: Yang Xiwen <forbidden405@outlook.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
This can avoid hardcoding a clock rate in driver. Also can enable the
clocks and deassert the resets if the pre-bootloader does not do this
for us.
Currently only enabled for Hi3798MV200.
Signed-off-by: Yang Xiwen <forbidden405@outlook.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Place the SDR104/HS200/HS400 checks into the mmc_deinit() and always
call it. This simplifies the code and removes ifdeffery. No functional
change is expected.
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Dragan Simic <dsimic@manjaro.org>
