Prefix the flash status codes (ERR_*) with FL_ in order to avoid clashes
with third-party libraries. Case in point: including the lwIP library
header file <lwip/err.h> which defines err_enum_t as an enum with values
being ERR_*.
Signed-off-by: Jerome Forissier <jerome.forissier@linaro.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Peter Robinson <pbrobinson@gmail.com>
This patch fixes timeout issues seen on large NOR flash.
For full-chip erase, where we use the SPINOR_OP_CHIP_ERASE (0xc7)
opcode. Use a different timeout for full-chip erase than for other
commands.
[Ported from Linux kernel commit
09b6a377687b ("mtd: spi-nor: scale up timeout for
full-chip erase") ]
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
Simon Glass <sjg@chromium.org> says:
This series includes the patches needed to make make the EFI 'boot' test
work. That test has now been split off into a separate series along with
the EFI patches.
This series fixes these problems:
- sandbox memory-mapping conflict with PCI
- the fix for that causes the mbr test to crash as it sets up pointers
instead of addresses for its 'mmc' commands
- the mmc and read commands which cast addresses to pointers
- a tricky bug to do with USB keyboard and stdio
- a few other minor things
Add device tree compatible string "renesas,rcar-gen4-rpc-if" to
the driver to match on upstream RPC DT node in R-Car Gen4 DTs.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Use the API function list_count_nodes() to count the number of list
entries.
Signed-off-by: Sughosh Ganu <sughosh.ganu@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Boot ROM on Meson needs some pages to be read/written in a special mode:
384 byte ECC mode (so called "short" by Amlogic) and with scrambling
enabled. Such pages are located on the chip in the following way (for
example):
[ p0 ][ p1 ][ p2 ][ p3 ][ p4 ][ p5 ][ p6 ][ p7 ] ... [ pN ]
^ ^ ^ ^
pX is page number "X". "^" means "special" page used by boot ROM - e.g.
every 2nd page in the range of [0, 7]. Step (2 here) and last page in
range is read from the device tree.
Signed-off-by: Arseniy Krasnov <avkrasnov@salutedevices.com>
Reviewed-by: Michael Trimarchi <michael@amarulasolutions.com>
Link: https://lore.kernel.org/r/20240826131710.29746-4-avkrasnov@salutedevices.com
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
If the function is called with no NAND device attached, then this
function can return error value, proceeding further ignoring the same
can cause system crash. This is seen when "mtd list" is run with no NAND
addon cards connected.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Acked-by: Roger Quadros <rogerq@kernel.org>
UBI block is an virtual device, that runs on top
of the MTD layer. The blocks are UBI volumes.
Intended to be used in combination with other MTD
drivers.
Despite the fact that it, like mtdblock abstraction,
it used with UCLASS_MTD, they can be used together
on the system without conflicting. For example,
using bcb command:
# Trying to load bcb via mtdblock:
$ bcb load mtd 0 mtd_partition_name
# Trying to load bcb via UBI block:
$ bcb load ubi 1 ubi_volume_name
User always must attach UBI layer (for example, using
ubi_part()) before using UBI block device.
Signed-off-by: Alexey Romanov <avromanov@salutedevices.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Acked-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
MTD block - abstraction over MTD subsystem, allowing
to read and write in blocks using BLK UCLASS.
Signed-off-by: Alexey Romanov <avromanov@salutedevices.com>
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Jiaxun Yang <jiaxun.yang@flygoat.com> says:
This is a subset of my previous arm64_be work.
I wish this could be merged first so it would be easier to work
against xtensa and arm64 be support.
So CONFIG_SYS_BIG_ENDIAN is our cross architecture option for
selecting machine endian, while the old CONFIG_CPU_BIG_ENDIAN
is defined by Arc only.
Use it whenever possible to ensure big endian code path is enabled
for all possible big endian machines.
Signed-off-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
include/nvmxip.h is a global and not a local include.
So we should use angle brackets.
Fixes: dc3abd8006 ("nvmxip: move header to include")
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Once a page is read with higher bitflips all subsequent reads
are returning the same bitflip value even though they have none.
max_bitflip variable is not being reset to 0 across page reads.
This is causing problems like incorrectly
marking erase blocks bad by UBI and causing read failures.
Verified the change with both MTD reads and UBI.
This change is inline with other NFC drivers.
Sample error log where a block is marked bad incorrectly:
ubi0: fixable bit-flip detected at PEB 125
ubi0: run torture test for PEB 125
ubi0: fixable bit-flip detected at PEB 125
ubi0 error: torture_peb: read problems on freshly erased PEB 125,
must be bad
ubi0 error: erase_worker: failed to erase PEB 125, error -5
ubi0: mark PEB 125 as bad
Link: https://lore.kernel.org/all/ea0422cd-a8e6-3c36-f551-a0142893301b@marvell.com
Signed-off-by: rminnikanti <rminnikanti@marvell.com>
Reviewed-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: rminnikanti <rminnikanti@marvell.com>
Acked-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
On DTR capable flashes like Micron Xcella the writes cannot start or end
at an odd address in DTR mode. Extra 0xff bytes need to be prepended or
appended respectively to make sure both the start and end addresses are
even.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Signed-off-by: Apurva Nandan <a-nandan@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Tested-by: Jonathan Humphreys <j-humphreys@ti.com>
Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
As part of bringing the master branch back in to next, we need to allow
for all of these changes to exist here.
Reported-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Tom Rini <trini@konsulko.com>
When bringing in the series 'arm: dts: am62-beagleplay: Fix Beagleplay
Ethernet"' I failed to notice that b4 noticed it was based on next and
so took that as the base commit and merged that part of next to master.
This reverts commit c8ffd1356d, reversing
changes made to 2ee6f3a5f7.
Reported-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Tom Rini <trini@konsulko.com>
Remove <common.h> from this driver directory and when needed
add missing include files directly.
Reviewed-by: William Zhang <william.zhang@broadcom.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Michal Simek <michal.simek@amd.com> says:
I looked as cleaning up some dependencies and I found that qconfig is
reporting some issues. This series is fixing some of them. But there are
still some other pending. That's why please go and fix them if they are
related to your board.
UTF-8: I am using uni2ascii -B < file to do conversion. When you run it in
a loop you will find some other issue with copyright chars or some issues
in files taken from the Linux kernel like DTs. They should be likely fixed
in the kernel first.
Based on discussion I am ignoring names too.
Convert UTF-8 chars to ASCII in cases where make sense. No Copyright or
names are converted.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Marek Behún <kabel@kernel.org>
Some of Kconfigs are using utf-8 encoding because of used chars. Convert
all of them to ascii enconging. Based on discussion ASCII should be used in
general with the exception of names.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
FMC2 IP supports up to 4 chip select. On MP1 SoC, only 2 of them are
available when on MP25 SoC, the 4 chip select are available.
Let's use a platform data structure for parameters that will differ.
Signed-off-by: Christophe Kerello <christophe.kerello@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
The first patch is by Weizhao Ouyang and avoids sf probe crashes.
The second patch is by Arseniy Krasnov and adds basic support for Amlogic
Meson NAND controller on AXG.
The following four patches are by Alexander Dahl and apply some fixes to
drivers/mtd/nand/raw/ and port some changes applied in Linux.
The following patch is by Bruce Suen and adds support for XTX SPINAND.
Finally, the last patch is again by Arseniy Krasnov and adds access to
OTP region, supporting info, dump, write and lock operations.
Introduced in upstream Linux with commit 7a08dbaedd365 for release v5.0.
When the new atmel nand driver was backported to U-Boot with commit
6a8dfd5722 ("nand: atmel: Add DM based NAND driver") that definition
was added to the driver instead of the header file. Move it over to the
other definitions with the same help text it has in Linux.
Code actually using this has not been ported over to raw nand base yet.
Link: https://lore.kernel.org/all/20240320090214.40465-3-ada@thorsis.com
Signed-off-by: Alexander Dahl <ada@thorsis.com>
Reviewed-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
