The Sielaff i.MX6 Solo board is a control and HMI board for vending
machines. Add support for this board.
The devicetree files are taken from pending changes in the Linux
kernel that are available from linux-next and will likely be
part of Linux v6.9.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
There is no imx8mp-msc-sm2s.dtb file in upstream Linux.
Change it to imx8mp-msc-sm2s-ep1.dtb.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Ian Ray <ian.ray@gehealthcare.com>
Redundant environment support is required for software updates.
Add support for it.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Ian Ray <ian.ray@gehealthcare.com>
Currently, the Ethernet ports are not working.
The Ethernet PHY reset lines are controlled by the TCA6424 I2C GPIO
expander.
The TCA6424 I2C GPIO expander is supported by the CONFIG_DM_PCA953X
driver.
Select the CONFIG_DM_PCA953X option so that the Ethernet PHYs can
go through a proper reset making Ethernet to be functional.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Ian Ray <ian.ray@gehealthcare.com>
These systems are unlikely to use EFI as this functionality has not been
enabled until it got pulled in by Kconfig default. This functionality
does add some 60-70 kiB to the u-boot.img size, which overflows the size
limit. Disable it.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Xilinx changes for v2024.04-rc3
zynqmp:
- Cover missing _SE chip variants to fix fpga programming
versal:
- Enable LTO for mini configurations
versal-net:
- Enable LTO for mini configurations
- Fix GIC address to aligned with real silicon
xilinx:
- DTs cleanup and fixups
- Enable HTTP boot
- Add missing spl header to zynqmp.c
add support for Serial Downloader Boot via UUU as well as flashing emmc
via UUU on USB0 Port of phyBOARD Pollux.
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Benjamin Hahn <B.Hahn@phytec.de>
Commit 68dcbdd594 ("ARM: imx: Add weak default reset_cpu()") caused
the 'reset' command in U-Boot to not cause a board reset.
Fix it by switching to the watchdog driver model via sysreset, which
is the preferred method for implementing the watchdog reset.
Signed-off-by: Fabio Estevam <festevam@denx.de>
U-Boot binary has grown in such a way that it goes beyond the reserved
area for the environment variables.
Running "saveenv" and rebooting the board causes U-Boot to hang because
of this overlap.
Fix this problem by selecting CONFIG_LTO so that the U-Boot proper
size can be reduced.
Also, to prevent this same problem to happen in the future, use
CONFIG_BOARD_SIZE_LIMIT, which can detect the overlap in build-time.
CONFIG_BOARD_SIZE_LIMIT is calculated as follows:
CONFIG_BOARD_SIZE_LIMIT = CONFIG_ENV_OFFSET - u-boot-img.dtb offset
CONFIG_BOARD_SIZE_LIMIT = 0xc000 - 69 * 1024
CONFIG_BOARD_SIZE_LIMIT = 715766
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@foundries.io>
Linux 6.6.y with KASLR enabled would print the following message on boot:
"
KASLR disabled due to lack of seed
"
Enable the 'kaslrseed' command so a random number seed can be pulled
from CAAM and inserted into the /chosen node 'kaslr-seed' property of
Linux kernel DT before boot, thus letting KASLR work properly.
Signed-off-by: Marek Vasut <marex@denx.de>
This commit enables support for DM_SERIAL in the vexpress_ca9x4 boards.
When running the board with the DM_SERIAL driver, the board ran out of
memory in SPL when initialising the DM serial driver.
Thus this required an increase in the pre-allocated SRAM memory. I did
increase it to 0x800, and it now works graciously.
It could probably be set lower, but I do not see any reason not to use the
available SRAM at this point.
Also adds stdout-path to the 'chosen' node in the device tree.
Signed-off-by: Ole P. Orhagen <ole.orhagen@northern.tech>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Enrico Leto <enrico.leto@siemens.com> says:
The common folder was initialially created for the common parts of
the products based on draco-am355x board family. We have the
product lines 'pxm2', 'rut' and the base line unfortunately named
'draco'! Adding the new capricorn-imx8 board family, the files
were enhanced without cleanup.
Simplify first EEPROM probe and access that implements both i2c
with & without driver model. Use abstraction functions for this.
Move all am355x specifics to a new file 'board_am335x'.
Clean-up includes, config checks, maintainer.
Writing to eMMC using HS200 mode work more reliably then other modes on
RK356x boards.
Add device tree props and enable Kconfig options for eMMC HS200 mode on
the generic RK3566/RK3568 board. Also enable the pinctrl driver in SPL
and add missing rk3568-generic.dtb to Makefile.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Testing has shown that writing to eMMC using a slower mode then HS200
typically generate an ERROR on first attempt on RK3588.
# Rescan using MMC legacy mode
=> mmc rescan 0
# Write a single block to sector 0x4000 fails with ERROR
=> mmc write 20000000 4000 1
# Write a single block to sector 0x4000 now works
=> mmc write 20000000 4000 1
With the MMC_SPEED_MODE_SET Kconfig option enabled.
Writing to eMMC using HS200 mode work more reliably than slower modes on
RK35xx boards. Enable MMC_HS200_SUPPORT Kconfig option by default to
prefer use of HS200 mode on RK356x and RK3588.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Enable Kconfig options to support AHCI, PCI and USB features. This help
keep rk3588-quartzpro64 in sync with other RK3588 boards.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Writing to eMMC using HS200 mode work more reliably then other modes on
RK3588 boards.
Enable MMC_HS200_SUPPORT Kconfig option to prefer use of HS200 mode.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Weizhao Ouyang <o451686892@gmail.com>
Sonoff iHost is gateway device designed to provide a Smart Home Hub,
it is based on Rockchip RV1126. There is also a version with 2GB RAM
based off the RV1109 dual core SoC however this works with the same
config as the RV1126 for uboot purposes.
Features:
- Rockchip RV1126
- 4GB DDR4
- 8GB eMMC
- microSD slot
- RMII Ethernet PHY
- 1x USB 2.0 Host
- 1x USB 2.0 OTG
- Realtek RTL8723DS WiFi/BT
- EFR32MG21 Silabs Zigbee radio
- Speaker/Microphone
Signed-off-by: Tim Lunn <tim@feathertop.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Enable the DM_ETH_PHY and PHY_REALTEK now that the designware ethernet
driver call eth_phy_set_mdio_bus() to assist with resetting the eth PHY
during probe.
Fixes ethernet on the v1.21 hw revision of Radxa ROCK Pi E:
=> mdio list
ethernet@ff540000:
1 - RealTek RTL8211F <--> ethernet@ff540000
=> net list
eth0 : ethernet@ff540000 86:e0:c0:ea:fa:a9 active
eth1 : ethernet@ff550000 86:e0:c0:ea:fa:a8
=> dhcp
Speed: 1000, full duplex
BOOTP broadcast 1
BOOTP broadcast 2
BOOTP broadcast 3
DHCP client bound to address 192.168.1.114 (1004 ms)
Reported-by: Trevor Woerner <twoerner@gmail.com>
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The CONFIG_SPL_STACK for rk3036 is removed in below patch, need to add
it back.
Fixes: f113d7d303 ("Convert CONFIG_SPL_STACK to Kconfig")
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Add support for Sophgo's Milk-V Duo board, only minimal device tree and
serial console are enabled, and it can boot via vendor first stage
bootloader.
Signed-off-by: Kongyang Liu <seashell11234455@gmail.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
The VisionFive 2 board supports saving the u-boot environment settings
are saved to on-board SPI flash. However the defconfig enables both
ENV_IS_NOWHERE and ENV_IS_IN_SPI_FLASH, preventing the "saveenv" command
to work. Fix that by disabling ENV_IS_NOWHERE.
Fixes: 7d79bed00c ("configs: starfive: Enable environment in SPI flash support")
Reported-by: E Shattow <lucent@gmail.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Latest RPi5 EEPROM firmware versions after "DATE: 2023/10/30", has changed
kernel load address from 0x80000 to 0x200000 which break boot process.
Switch to position independent code to be able to boot the same binary
on top of different EEPROM firmware versions.
Tested on:
Raspberry Pi 5 Model B Rev 1.0
Raspberry Pi 4 Model B Rev 1.1
Raspberry Pi 3 Model B Plus Rev 1.3
Raspberry Pi Zero 2 W Rev 1.0
Raspberry Pi 2 Model B Rev 1.2
Raspberry Pi Compute Module 4 Rev 1.0
Raspberry Pi Compute Module 3 Rev 1.0
Tested-by: Jens Maus <mail@jens-maus.de>
Tested-by: Darko Alavanja <darko.alavanja@konsulko.com>
Signed-off-by: Ivan T. Ivanov <iivanov@suse.de>
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
FriendlyElec NanoPi Duo2 is a tiny SBC with Allwinner H3 and
Ampak AP6212 WiFi module. The device-tree for it is already
available in u-boot source tree. Add a default config for it.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
[Andre: enable USB gadgets]
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
This is a Chinese TV box based on Allwinner H618 SoC.
The DRAM parameters were derived from the values found in a firmware update.
Signed-off-by: Nick Alilovic <nickalilovic@gmail.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
We have a Python test the copying of SMBIOS tables from QEMU.
To make use of the test we need the smbios command.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Add support for WinLink E850-96 board [1]. It's based on Exynos850 SoC
and follows 96boards specification, so it's compatible with 96boards
mezzanine boards [2]. This patch enables next features:
* Serial console
* USI
* PMU (muxing AP UART path)
* Pinctrl
* Clocks
* Timer (ARMv8 architected)
* Reset control
It's quite a minimal enablement. Features like MMC, USB and Ethernet
will be enabled later.
The rationale for config values is as follows:
* TEXT_BASE = 0xf8800000
That's where BL2 loads the U-Boot payload, so TEXT_BASE must be
exactly this value. Overall the memory map is designed in a way to
keep the bootloader in the upper 128 MiB area of RAM, which is
0xf8000000..0xffffffff. That includes bootloader's code, stack,
data, heap, MMU tables, etc. All the memory below that 128 MiB chunk
can be used for storing boot images (0x80000000..0xf8000000).
* CUSTOM_SYS_INIT_SP_ADDR = 0xf8c00000
Just 4 MiB above the TEXT_BASE address, to leave enough space for
U-Boot code and stack itself (grows downwards).
* SYS_LOAD_ADDR = 0x80000000
The beginning of RAM. That's where Linux kernel image must be
loaded.
* SYS_MALLOC_LEN = 0x81f000
8 MiB for malloc() + ENV_SIZE (128 KiB)
* SYS_MALLOC_F_LEN = 0x4000
Increase malloc() pool size available before relocation from 8 KiB
(default) to 16 KiB. Otherwise "alloc space exhausted" message
appears in U-Boot log during board_init_f() stage. There are next
reasons for doing so:
1. Having "bootph-all" flags in some dts nodes leads to binding
those during pre-relocation stage, and binding (DM) uses
dynamic memory allocation
2. clk-exynos850 driver uses CCF clocks, which in turn use dynamic
memory allocation
Device tree file was imported from Linux kernel. All nodes and boot
phase flags added in exynos850-e850-96-u-boot.dtsi are only needed to
enable serial console:
* oscclk -> cmu_top -> cmu_peri: generate UART/USI clocks
* pinctrl_alive and uart1_pins: needed to mux UART pins
* pmu_system_controller: configures AP UART path to uart1_pins
* usi_uart: configures USI block to operate as a UART protocol
* serial_0: enables serial console (UART)
[1] https://www.96boards.org/product/e850-96b/
[2] https://www.96boards.org/products/mezzanine/
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
The help for CONFIG_MTD explains that it needs to be enabled for various
things like NAND, etc to be available. It however then doesn't enforce
this dependency and so if you have none of these systems present you
still need to disable a number of options. Fix this by making places
that select/imply one type of flash, but did not do the same, also do
this for "MTD". Make boards which hadn't been enabling MTD already but
need it now, do so. In a few places, disable CONFIG_CMD_MTDPARTS as it
wasn't previously enabled but was now being implied.
Signed-off-by: Tom Rini <trini@konsulko.com>
Linux 6.6.y with KASLR enabled would print the following message on boot:
"
KASLR disabled due to lack of seed
"
Enable the 'kaslrseed' command so a random number seed can be pulled
from CAAM and inserted into the /chosen node 'kaslr-seed' property of
Linux kernel DT before boot, thus letting KASLR work properly.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Commit 68dcbdd594 ("ARM: imx: Add weak default reset_cpu()") caused
the 'reset' command in U-Boot to not cause a board reset.
Fix it by switching to the watchdog driver model via sysreset, which
is the preferred method for implementing the watchdog reset.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
