Falcon mode is very useful in improving boot speed. A question that
Falcon mode asks is "Where do I look for the kernel". With MMC boot
media, the correct answer is CONFIG_SYS_MMCSD_RAW_MODE_KERNEL_SECTOR.
The scope of this patch is to move this to Kconfig.
It is possible for a system to support Falcon mode from NOR but not
MMC. In that case, mmc_load_image_raw_os() would not be used. To
address this, conditionally compile mmc_load_image_raw_os() when
SPL_FALCON_BOOT_MMCSD, instead of SPL_OS_BOOT.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
[trini: Move spl_start_uboot to its own guard in spl_mmc.c, rerun migration]
Signed-off-by: Tom Rini <trini@konsulko.com>
Xilinx changes for v2022.04-rc1
gpio:
- Add modepin driver
net:
- Save random mac addresses to eth variable
zynqmp gem:
- Add support for mdio bus DT description
- Add support for reset and SGMII phy configuration
- Reduce timeout for MDIO accesses
zynqmp clk:
- Fix clock handling for gem and usb
phy:
- Add zynqmp phy/serdes driver
serial:
- Add one missing compatible string
microblaze:
- Symbol alignement
- SPL fixups
- Code cleanups
zynqmp:
- Various dt changes, DP pre-reloc, gem resets, gem clocks
- Switch SOM to shared psu configuration
- Move dcache handling to firmware driver
- Workaround gmii2rgmii DT description issue
- Enable broadcasts again
- Change firmware enablement logic
- Small adjustement in firmware driver
versal:
- Support new mmc@ DT nodes
- Fix run time variable handling
- Add missing I2C_PMC ID for power domain
The am335x-ice-v2 board's Ethernet ports can be configured
in 'MII' or 'RMII' mode to be connected to 'PRUSS' or 'CPSW'
Ethernet subsystems.
This patch sets the environment variable 'ice_mii' to
'mii' or 'rmii' accordingly. Based on that we choose the
appropriate board devicetree i.e. 'am335x-ice-v2.dtb' or
'am335x-ice-v2-prueth.dtb'.
Since there are 2 Ethernet ports with 2 modes, there can be 4
configurations but for now we consider both ports in different modes
to be an invalid configuration and prevent boot in that case.
Signed-off-by: Roger Quadros <rogerq@ti.com>
[Amjad: use overlay instead of using new am335x-ice-v2-prueth.dtb]
Signed-off-by: Amjad Ouled-Ameur <aouledameur@baylibre.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
[trini: Make prueth_is_mii be marked __maybe_unused]
Signed-off-by: Tom Rini <trini@konsulko.com>
BOOT_TARGET_DEVICES should only be added if the corresponding u-boot
command is enabled otherwise the build will fail.
Signed-off-by: Piotr Kubik <piotr_kubik@vp.pl>
These hardcoded values were calculated from CONFIG_SPL_TEXT_BASE macro. Now
this macro is configurable via Kconfig, so calculate values 0x0030/0x4030
at compile time via CONFIG_SPL_TEXT_BASE option. Values 0x0030/0x4030
represents offset of CONFIG_SPL_TEXT_BASE from address 0x40000000.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Memory layout in the comment is from Armada XP platform which uses load
address 0x40004030. DB-88f6720 is Armada 375 platform which uses same load
address as Armada 38x which is 0x40000030.
Currently SPL support for Armada 375 is unfinished and does not work. There
is missing Serdes initialization and DDR3 training code. So nobody noticed
that CONFIG_SPL_* options are not correct.
Fix at least CONFIG_SPL_TEXT_BASE constant and remove incorrect comments
about memory layout. So it is not misleading.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
- disable CONFIG_NET_RANDOM_ETHADDR when unnecessary on amlogic based configs
- meson64_android: add board specific env settings, in order to support VIM3/L for android
- add changes to support VIM3/L android boot by using meson64_android.h config
After the conversion to DM the SD card shows up as 'mmc 2'
device.
Adjust the 'mmcdev' and the distro command 'func' accordingly.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Peter Robinson <pbrobinson@gmail.com>
Enable support for USB and USB storage on the UDOO Neo.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
This fixes booting from the mSD card from both SPL and when
using it for the OS booting. It also cleans up a few mmc
booting bits that are no longer needed.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
In AOSP, both VIM3 and VIM3L have 2 bootloader flavors,
depending on A/B enablement.
For example, for vim3l, the naming is:
- u-boot_kvim3l_noab.bin : legacy support
- u-boot_kvim3l_ab.bin : A/B support
Prepare a defconfig to support u-boot_kvim3_ab.bin and
u-boot_kvim3l_ab.bin.
This is identical to khadas-vim3{l}_ab_android but will be updated in
the next commit.
Also update partitioning tables for A/B support.
Signed-off-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lore.kernel.org/r/20211122152207.219023-4-mkorpershoek@baylibre.com
Microblaze is one the last two users of the CONFIG_SYS_RESET_ADDRESS
macro (the other is arch/powerpc/cpu/mpc8xx/cpu.c, but the macro is not
defined anywhere in powerpc code, so it should be removed there too).
Replace CONFIG_SYS_RESET_ADDRESS usage in start.S with
CONFIG_SYS_TEXT_BASE. If the reset address should really be
user-configurable, a new Kconfig option could be added.
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
Link: https://lore.kernel.org/r/20211130163358.2531677-6-ovidiu.panait@windriver.com
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The memory layout is taken from the device tree passed to us by
m1n1, so there is no need to define this.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
The SMSC driver is using the old driver model.
Init the virtio system in vexpress64.c so that the network device is
discovered.
Signed-off-by: Peter Hoyes <Peter.Hoyes@arm.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Move env var address values to #defines so they can be reused elsewhere.
Rename env var names to those recommended in the README and modify
addresses to allow more space for the kernel.
Fix issue where fdt is called with invalid arguments when booting
without a ramdisk.
Signed-off-by: Peter Hoyes <Peter.Hoyes@arm.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Rename from vexpress_aemv8a.h -> vepxress_aemv8.h as new FVPs may not be
v8-A. No change in behavior.
This is towards future work to enable support for the FVP_BaseR.
Signed-off-by: Peter Hoyes <Peter.Hoyes@arm.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
When using a recent kernel with a bunch of compiled-in
stuff the kernel image easily becomes bigger than 8 MB
yielding this error:
Loading Kernel Image
Image too large: increase CONFIG_SYS_BOOTM_LEN
Must RESET board to recover
Fix this by bumping to SZ_64MB.
Cc: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Stephan Gerhold <stephan@gerhold.net>
- various fixes to the sandbox display support
- support for showing a logo without splash screen config
- support for BMP drawing to depths other than 16bpp
- tests for the different types of supported BMP images
- support showing a logo when running coreboot via qemu
This converts the following to Kconfig:
CONFIG_JFFS2_DEV
CONFIG_JFFS2_LZO
CONFIG_JFFS2_NAND
CONFIG_JFFS2_PART_OFFSET
CONFIG_JFFS2_PART_SIZE
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_88F5182
CONFIG_BOARD_IS_OPENRD_BASE
CONFIG_BOARD_IS_OPENRD_CLIENT
CONFIG_BOARD_IS_OPENRD_ULTIMATE
CONFIG_D2NET_V2
CONFIG_FEROCEON
CONFIG_FEROCEON_88FR131
CONFIG_INETSPACE_V2
CONFIG_KW88F6192
CONFIG_KW88F6281
CONFIG_KW88F6702
CONFIG_NET2BIG_V2
CONFIG_NETSPACE_LITE_V2
CONFIG_NETSPACE_MAX_V2
CONFIG_NETSPACE_MINI_V2
CONFIG_NETSPACE_V2
CONFIG_SHEEVA_88SV131
At this point mv-plug-common.h is now only an include of mv-common.h so
remove that indirection.
Signed-off-by: Tom Rini <trini@konsulko.com>
The only place we use CONFIG_CPU_ARMV8 was in the arm_dcc serial driver.
Switch this to CONFIG_ARM64 today, and if in the future we need finer
granularity tuning here, a new CONFIG_SERIAL option needs to be
introduced.
Signed-off-by: Tom Rini <trini@konsulko.com>
In order to finish moving this symbol to Kconfig for all platforms, we
need to do a few more things. First, for all platforms that define this
to a function, introduce CONFIG_DYNAMIC_SYS_CLK_FREQ, similar to
CONFIG_DYNAMIC_DDR_CLK_FREQ and populate clock_legacy.h. This entails
also switching all users from CONFIG_SYS_CLK_FREQ to get_board_sys_clk()
and updating a few preprocessor tests.
With that done, all platforms that define a value here can be converted
to Kconfig, and a fall-back of zero is sufficiently safe to use (and
what is used today in cases where code may or may not have this
available). Make sure that code which calls this function includes
<clock_legacy.h> to get the prototype.
Signed-off-by: Tom Rini <trini@konsulko.com>
This CONFIG option is used in one of two ways. The first way is that it
is defined to a static value, of an unsigned long size. The second way
is that it is defined to something, typically a function, to determine
this value at run time.
However, in a few cases that function returns a static value. Change
that to using the static value directly.
In the case of using something at run time, convert everything to using
a function of the same name and prototype. This will allow for further
cleanups.
Finally, we have a few cases where the function is just not used, so
drop it.
Signed-off-by: Tom Rini <trini@konsulko.com>
The values CONFIG_SYS_CLK_FREQ_C100 and CONFIG_SYS_CLK_FREQ_C110 are
only used in one place and not changed by the board config file. Move
these out of the CONFIG namespace and in to the CFG namespace.
Signed-off-by: Tom Rini <trini@konsulko.com>
In order to finish this conversion we need to add a symbols for
SPL_SYS_NAND_SELF_INIT and TPL_SYS_NAND_SELF_INIT as there are cases
there where we need to, or need to not, use that framework as things
stand.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SYS_FSL_CLK
We move the exiting option to common/Kconfig near the other options to
control the contents of board_init_f() and note that this is a legacy
option. We further restrict this to where the call is going to be
non-empty, for the SoCs that had only been using this for some
MMC-related clocks.
Signed-off-by: Tom Rini <trini@konsulko.com>
