Add support for PWM backlight found in Samsung CMC623 image converter.
Signed-off-by: Ion Agorria <ion@agorria.com>
Reviewed-by: Svyatoslav Ryhel <clamor95@gmail.com>
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Samsung S6E63M0 controller is found in some OLED panels like one used in
the Samsung Captivate Glide. Currently only DBI C panel is implemented.
Signed-off-by: Ion Agorria <ion@agorria.com>
Reviewed-by: Svyatoslav Ryhel <clamor95@gmail.com>
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Sony L4F00430T01 LCD module is found in Samsung Galaxy R. The panel has a
WVGA resolution (480x800) and is setup over SPI, video data comes from RGB.
Signed-off-by: Ion Agorria <ion@agorria.com>
Reviewed-by: Svyatoslav Ryhel <clamor95@gmail.com>
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Add support for Skyworks AAT2870 LED Backlight Driver and Multiple LDO
Lighting Management Unit. Only backlight is supported as for now. Supported
backlight level range is from 2 to 255 with step of 1.
Tested-by: Ion Agorria <ion@agorria.com>
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
LG LH400WV3-SD04 is a color active matrix TFT (Thin Film Transistor)
liquid crystal display (LCD). The resolution of a 4" contains 480 x 800
pixels.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Hitachi TX10D07VM0BAA is a color active matrix TFT (Thin Film Transistor)
liquid crystal display (LCD). The resolution of a 4" contains 480 x 800
pixels.
Tested-by: Ion Agorria <ion@agorria.com>
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
[backport from Linux commits 9b26d5c044d6a29ebfb1845408e0f2a7c5f89818
and 219a1f49094f50bf9c382830d06149e677f76bed]
The patch adds the FRIDA FRD400B25025-A-CTK panel, which belongs to the
Novatek NT35510-based panel family.
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Some drivers call video_set_flush_dcache() to indicate that they want to
have the dcache flushed for the frame buffer. These drivers benefit from
our new video damage control, because we can reduce the amount of memory
that gets flushed significantly.
This patch enables video damage control for all device drivers that call
video_set_flush_dcache() to make sure they benefit from it.
Signed-off-by: Alexander Graf <agraf@csgraf.de>
[Alper: Add to VIDEO_TIDSS, imply instead of select]
Co-developed-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
CONFIG_VIDEO_COPY implemented a range-based copying mechanism: If we
print a single character, it will always copy the full range of bytes
from the top left corner of the character to the lower right onto the
uncached frame buffer. This includes pretty much the full line contents
of the printed character.
Since we now have proper damage tracking, let's make use of that to reduce
the amount of data we need to copy. With this patch applied, we will only
copy the tiny rectangle surrounding characters when we print them,
speeding up the video console.
After this, changes to the main frame buffer are not immediately copied
to the copy frame buffer, but postponed until the next video device
sync. So issue an explicit sync before inspecting the copy frame buffer
contents for the video tests.
Signed-off-by: Alexander Graf <agraf@csgraf.de>
[Alper: Rebase for fontdata->height/w, fill_part(), fix memmove(dev),
drop from defconfig, use damage.xstart/yend, use IS_ENABLED(),
call video_sync() before copy_fb check, update video_copy test]
Co-developed-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
Link: https://lore.kernel.org/u-boot/20230821135111.3558478-12-alpernebiyasak@gmail.com/
We are going to introduce image damage tracking to fasten up screen
refresh on large displays. This patch adds damage tracking for up to
one rectangle of the screen which is typically enough to hold blt or
text print updates. Callers into this API and a reduced dcache flush
code path will follow in later patches.
Signed-off-by: Alexander Graf <agraf@csgraf.de>
Reported-by: Da Xue <da@libre.computer>
[Alper: Use xstart/yend, document new fields, return void from
video_damage(), declare priv, drop headers, use IS_ENABLED()]
Co-developed-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
Link: https://lore.kernel.org/u-boot/20230821135111.3558478-5-alpernebiyasak@gmail.com/
Reviewed-by: Simon Glass <sjg@chromium.org>
The LM3532 is a 500-kHz fixed frequency asynchronous boost converter which
provides the power for 3 high-voltage, low-side current sinks. The device
is programmable over an I2C-compatible interface and has independent
current control for all three channels.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Add support for the LCD panel module used in Motorola Atrix 4G or Droid X2.
Exact panel vendor and model are unknown. The panel has a 540x960 (qHD)
resolution and uses 24 bit RGB per pixel.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Place Tegra124 SOR and eDP implenetation into common Tegra driver folder
until it is integrated into existing setup.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Since this set of drivers suports four Tegra SoC generations, lets name it
just 'tegra'.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Reviewed-by: Peter Robinson <pbrobinson@gmail.com>
Since EDID only indicates supported standard timings, a large table with
detailed timing information is necessary, consuming significant space. To
mitigate this, the table is made configurable via kconfig, allowing it to
be excluded when not needed.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
The configuration options CONFIG_VIDCONSOLE_AS_LCD and CONFIG_VIDCONSOLE_AS_
NAME have been marked as obsolete and scheduled for deletion in late 2020.
That's already long overdue and the last remaining consumers of these options
have already migrated to using "vidconsole" in their "stdout" and "stderr"
environment variables, so let's delete these two configuration options.
Signed-off-by: Dragan Simic <dsimic@manjaro.org>
Acked-by: Soeren Moch <smoch@web.de> # tbs2910
This module is a color active matrix LCD module incorporating
Oxide TFT (Thin Film Transistor). It is composed of a color TFT-LCD
panel, driver ICs, a control circuit and power supply circuit, and
a backlight unit. Graphics and texts can be displayed on a 1536x2048
dots panel with (16,777,216) colors by using MIPI DUAL DSI interface,
supplying +3.3V DC supply voltage for TFT-LCD panel driving and
supplying DC supply voltage for LED Backlight.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Add support for National Semiconductor/TI LP8550/1/2/3/5/6/7
LED Backlight. Driver is based on Linux version but is
reworked and optimised for U-Boot DM framework. Currently
only register driven backlight control is supported, PWM
driver backlight control may be added later if needed.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
This module is a color active matrix LCD module incorporating
Oxide TFT (Thin Film Transistor). It is composed of a color TFT-LCD
panel, driver ICs, a control circuit and power supply circuit, and
a backlight unit. Graphics and texts can be displayed on a 2560×1600
dots panel with (16,777,216) colors by using MIPI DUAL DSI interface,
supplying +3.3V DC supply voltage for TFT-LCD panel driving and
supplying DC supply voltage for LED Backlight.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
At present U-Boot flushes the cache after every character written to
the display. This makes the command-line slower, to the point that
pasting in long strings can fail.
Add a cyclic function to sync the display every 10ms. Enable this by
default.
Allow much longer times for sandbox, since the SDL display is quite
slow.
Avoid size growth if the feature is disabled by making the new init and
destroy functions dependent on CYCLIC being enabled.
Signed-off-by: Simon Glass <sjg@chromium.org>
LTL106HL02 is a color active matrix TFT (Thin Film Transistor)
liquid crystal display (LCD) that uses amorphous silicon TFT as
switching devices. This model is composed of a TFT LCD panel, a
driver circuit and a backlight unit. The resolution of a 10.6"
contains 1920 x 1080 pixels and can display up to 16,8M color
with wide viewing angle.
Co-developed-by: Jonas Schwöbel <jonasschwoebel@yahoo.de>
Signed-off-by: Jonas Schwöbel <jonasschwoebel@yahoo.de>
Co-developed-by: Svyatoslav Ryhel <clamor95@gmail.com>
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Signed-off-by: Anton Bambura <jenneron@protonmail.com>
The LD070WX3 is a Color Active Matrix Liquid Crystal Display with
an integral Light Emitting Diode (LED) backlight system. The
matrix employs a-Si Thin Film Transistor as the active element. It
is a transmissive type display operating in the normally Black
mode. This TFT-LCD has 7.0 inches diagonally measured active
display area with WXGA resolution (800 by 1280 pixel array).
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
This is needed to support Truetype fonts. In any case, the compiler
expects SSE to be available in 64-bit mode. Provide an option to enable
SSE so that hardware floating-point arithmetic works.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Suggested-by: Bin Meng <bmeng.cn@gmail.com>
While it is nice to have the font command, using 'select' makes it
impossible to build the console code without it. Stop using 'select' and
make it default if CONSOLE_TRUETYPE is enabled when asking the command.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
These appear prominently in the main menu at present. Move them to the
video Kconfig where they belong.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
At present this feature is enabled in SPL if a bloblist is available.
Some platforms may not want to use this, so add an option to allow the
feature to be disabled.
Note that the feature unfortunately only fills in part of the
video-handoff information, so causes failures on x86 platforms. For now,
disable it there.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com> # qemu-x86_64
It is not a parse error to have a default value of "0" for a "hex" type
entry, instead of "0x0". However, "0" and "0x0" are not treated the
same even by the tools themselves. Correct this by changing the default
value from "0" to "0x0" for all hex type questions that had the
incorrect default. Fix one instance (in two configs) of a default of "0"
being used on a hex question to be "0x0". Remove the cases where a
defconfig had set a value of "0x0" to be used as the default had been
"0".
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Set up a default frame buffer size of 8MiB for Bochs for non-x86
architecturs as PCI is normally not enumerated before relocation
on these architectures.
Signed-off-by: Bin Meng <bmeng@tinylab.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
PCI is always selected by X86 architecture hence "X86 && PCI" does
not make it better.
Signed-off-by: Bin Meng <bmeng@tinylab.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org> # qemu-x86_64
There is an example in the VIDEO_PCI_DEFAULT_FB_SIZE help text to
tell people how to calculate its value but the resolution given
does not match the value. Fix it.
Signed-off-by: Bin Meng <bmeng@tinylab.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Now that the driver is legacy free, remove the x86 dependency so
that it can be used on non-x86 architectures.
Signed-off-by: Bin Meng <bmeng@tinylab.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org> # qemu-x86_64
This is required since user may want to either call the remove method
of video driver and reset the display or not call the remove method
to continue displaying until next stage.
Signed-off-by: Nikhil M Jain <n-jain1@ti.com>
Reviewed-by: Devarsh Thakkar <devarsht@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Bochs is convenient with QEMU on x86 since it does not require a video
BIOS. Add a driver for it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
The driver is for panels based on the Himax HX8394 controller, such as the
HannStar HSD060BHW4 720x1440 TFT LCD panel that uses a MIPI-DSI interface.
This panel is used in Pinephone Pro.
Signed-off-by: Ondrej Jirman <megi@xff.cz>
Cc: Anatolij Gustschin <agust@denx.de>
Make it clear that this is the SPL option to avoid potential confusion
when the description for CONFIG_SPL_VIDEO is the same as that for
CONFIG_VIDEO.
Signed-off-by: John Keeping <john@metanate.com>
Family of panels used by HTC in One X. Though were used variants
at least from 3 vendors, this driver provides generic support for
all of them.
Tested-by: Ion Agorria <ion@agorria.com> # HTC One X T30 Sony
Tested-by: Svyatoslav Ryhel <clamor95@gmail.com> # HTC One X T30 Sharp
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Driver adds support for panels with Renesas R69328 IC
Currently supported compatible is:
- jdi,dx12d100vm0eaa
Tested-by: Andreas Westman Dorcsak <hedmoo@yahoo.com> # LG P880 T30
Tested-by: Svyatoslav Ryhel <clamor95@gmail.com> # LG P895 T30
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
R61307 is liquid crystal driver for high-definition
amorphous silicon (a-Si) panels and is ideal for
tablets and smartphones.
Supported compatibles are:
- koe,tx13d100vm0eaa
- hitachi,tx13d100vm0eaa
Tested-by: Andreas Westman Dorcsak <hedmoo@yahoo.com> # LG P880 T30
Tested-by: Svyatoslav Ryhel <clamor95@gmail.com> # LG P895 T30
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This is basic lm3533 driver only with bank A and backlight cell
support.
Tested-by: Andreas Westman Dorcsak <hedmoo@yahoo.com> # LG P880 T30
Tested-by: Svyatoslav Ryhel <clamor95@gmail.com> # LG P895 T30
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add Kconfigs which enable the video driver and splash screen at SPL
stage only and not at u-boot proper. The existing Kconfigs from u-boot
proper were not used to make SPL splash screen independent to them.
Signed-off-by: Nikhil M Jain <n-jain1@ti.com>
Reviewed-by: Devarsh Thakkar <devarsht@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Move tegra dc driver to tegra20 directory and also mention
T30 in description of the driver's config option.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
[agust: add commit description]
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Modern mobile phones typically have high pixel density.
Bootmenu is hardly readable on those with 8x16 font.
Signed-off-by: Dzmitry Sankouski <dsankouski@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Modern mobile phones typically have high pixel density.
Bootmenu is hardly readable on those with 8x16 font.
Signed-off-by: Dzmitry Sankouski <dsankouski@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Allow font size configuration at runtime for console_simple.c
driver. This needed for unit testing different fonts.
Configuring is done by `font` command, also used for font
selection in true type console.
Signed-off-by: Dzmitry Sankouski <dsankouski@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This needed for unit testing different fonts.
Configured fonts are placed in an array of fonts.
First font is selected by default upon console probe.
Signed-off-by: Dzmitry Sankouski <dsankouski@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
[agust: fixed build error when bmp logo disabled]
Signed-off-by: Anatolij Gustschin <agust@denx.de>
