Commit 86acdce2ba ("common: add config for board_init() call")
introduced CONFIG_BOARD_INIT option. This option can be disabled for the
boards where board_init() function is not needed. Remove empty
board_init() calls for all boards where it's possible, and disable
CONFIG_BOARD_INIT in all related defconfigs.
This cleanup was made semi-automatically using these scripts: [1].
No functional change, but the binary size for the modified boards is
reduced a bit.
[1] https://github.com/joe-skb7/uboot-convert-scripts/tree/master/remove-board-init
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Tested-by: Adam Ford <aford173@gmail.com> #imx8mm_beacon
Tested-by: Bryan Brattlof <bb@ti.com>
Acked-by: Peng Fan <peng.fan@nxp.com> #NXP boards
Rename the variable and add ENV_ prefix, so that all configuration
options which are related to environment would have an CONFIG_ENV_
prefix. No functional change.
Use ENV_MMC_EMMC_HW_PARTITION to clarify this is the eMMC hardware
partition selector, not a software partition table entry selector.
Retain the ENV_MMC_ prefix to make it easier to search for all the
SD/MMC related ENV options. Update the help text accordingly.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Rename the variable and add ENV_ prefix, so that all configuration
options which are related to environment would have an CONFIG_ENV_
prefix. No functional change.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
In kernel device tre commit 714d54917147: ("arm64: dts: ti: k3-j722s-evm:
Enable PMIC") adds pmic support.
Above commit of kernel get synched in u-boot by sha ab06a533f08e:("Squashed
'dts/upstream/' changes from 8531b4b4988c..955176a4ff59").
Now, PMIC DT is available in u-boot for J722S EVM,
So enable PMIC in defconfig as well.
Signed-off-by: Udit Kumar <u-kumar1@ti.com>
SPL_TEXT_BASE is used as the load address for the main domain SPL on k3
platforms.
Since the config value is the same for every board, this patch sets the
value 0x80080000 as default for all 64-bit ARCH_K3, 0x43c00000 as
default for the R5 cores and deletes the instances of SPL_TEXT_BASE in
individual defconfigs.
Signed-off-by: Anshul Dalal <anshuld@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Enable ESM configs. ESMs are a prerequisite to enable
watchdog reset functionality. The ESM aka error signalling module
is primarily responsible for sensing the watchdog reset event.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Judith Mendez <jm@ti.com> says:
Some K3 devices like am62x and am64x have a M4 processor in the MCU
voltage domain. This patch series introduces remoteproc M4 driver which
will be used to load firmware into and start the M4 remote core.
This series also adds support for R5F cores on am64x SoCs in patch 2 and
sets up environment to load FW in remote cores in patch 3,4,5.
This patch series also enables remoteproc drivers by default as per what
remoteproc sybsystem is supported per SoC, thus all remoteproc options
are now deleted in configs/* since they are no longer required.
This patch series was tested on am64x EVM, am62x SK, am62ax SK,
am62px SK boards.
Any additional tested by's are welcome since I was not able to
test any additional boards.
Tested by running the following commands in u-boot prompt:
=> setenv dorprocboot 1
=> run boot_rprocs
Link: https://lore.kernel.org/r/20250210202944.1071931-1-jm@ti.com
Now that remoteproc configs are enabled by default in Kconfig
files, remove these configs which are no longer needed to be
defined here in configs/.
Signed-off-by: Judith Mendez <jm@ti.com>
Reviewed-by: Andrew Davis <afd@ti.com>
Prepare the introduction of the lwIP (lightweight IP) TCP/IP stack by
adding a new net/lwip/ directory and the NET_LWIP symbol. Network
support is either NO_NET, NET (legacy stack) or NET_LWIP. Subsequent
commits will introduce the lwIP code, re-work the NETDEVICE integration
and port some of the NET commands and features to lwIP.
SPL_NET cannot be enabled when NET_LWIP=y. SPL_NET pulls some symbols
that are part of NET (such as arp_init(), arp_timeout_check(),
arp_receive(), net_arp_wait_packet_ip()). lwIP support in SPL may be
added later.
Similarly, DFU_TFTP and FASTBOOT are not compatible with NET_LWIP
because of dependencies on net_loop(), tftp_timeout_ms,
tftp_timeout_count_max and other NET things. Let's add a dependency on
!NET_LWIP for now.
SANDBOX can select NET_LWIP but doing so will currently disable the eth
dm tests as well as the wget tests which have strong dependencies on the
NET code.
Other adjustments to Kconfig files are made to fix "unmet direct
dependencies detected" for USB_FUNCTION_SDP and CMD_FASTBOOT when
the default networking stack is set to NET_LWIP ("default NET_LWIP"
instead of "default NET" in Kconfig).
The networking stack is now a choice between NO_NET,
NET and NET_LWIP. Therefore '# CONFIG_NET is not set' should be
'CONFIG_NO_NET=y'. Adjust the defconfigs accordingly.
Signed-off-by: Jerome Forissier <jerome.forissier@linaro.org>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Make the raw-mode options depend on SPL_SYS_MMCSD_RAW_MODE in a more
direct way. This makes it easier to understand the options with
'make menuconfig'.
There are three different ways of specifying the offset:
- sector offset
- partition number
- partition type
So make these a choice, so it is more obvious what is going on.
Update existing boards to enable SPL_SYS_MMCSD_RAW_MODE where needed.
Reviewed-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Quentin Schulz <quentin.schulz@cherry.de>
Signed-off-by: Simon Glass <sjg@chromium.org>
Introduce the initial configs needed to support the J722S SoC family.
Signed-off-by: Vaishnav Achath <vaishnav.a@ti.com>
Signed-off-by: Jayesh Choudhary <j-choudhary@ti.com>
