Use content of EEPROM to detect the actual RAM size and adjust
DDR timings, size and banks accordingly.
Also enable the SoM detection per default in the defconfigs.
Signed-off-by: Wadim Egorov <w.egorov@phytec.de>
Tested-by: John Ma <jma@phytec.com>
Daniel Schultz <d.schultz@phytec.de> says:
This patch series adds support for the EEPROM v3 API.
V3 is backwards compatible to V2 and therefore, the V2 image still
exists at the beginning. Only the API version changed from 2 to 3.
V3 is a block-based memory layout organized as singled-linked list
with different types of blocks. This is a more flexible approach and
allows us to extend it by more block types in the future.
The V3 data starts with a 8-byte large header which defines the
block count (u8), V3 subversion (u8) and data payload length (u16).
Additionally the header contains a CRC8 checksum a 3 reserved bytes.
Each block starts with a 4-byte large header which defined the
block type (u8), the absolute address of the next block (u16) and a
CRC8 checksum. The content itself is defined via the block type and
we currently have 2 different types:
1) MAC: Contains the Ethernet interface number (u8), MAC address
(6 x u8) and a CRC8 checksum.
Enable CONFIG_ENV_OVERWRITE to overwrite ethaddr in the environment.
This is required because our environment is not located in the
boot partition.
Signed-off-by: Daniel Schultz <d.schultz@phytec.de>
Tested-by: Wadim Egorov <w.egorov@phytec.de>
The K3 J784S4 SoC has four dual-core R5F subsystems and four C71x DSP
subsystems. Set config values to enable the remoteproc functionality
with these R5F and DSP subsystems.
Signed-off-by: Beleswar Padhi <b-padhi@ti.com>
Move to using OF_UPSTREAM config and thus using the devicetree-rebasing
subtree.
Signed-off-by: Neha Malcom Francis <n-francis@ti.com>
Acked-by: Sumit Garg <sumit.garg@linaro.org>
Add defconfig for J721E SK R5 and A72 configuration.
This includes and modifies the J721E EVM defconfigs:
j721e_evm_r5_defconfig -> j721e_sk_r5_defconfig
j721e_evm_a72_defconfig -> j721e_sk_a72_defconfig
Signed-off-by: Neha Malcom Francis <n-francis@ti.com>
Marek Behún <kabel@kernel.org> says:
This series contains improvements for the 'eeprom' command:
- refactors
- fixes
- improvements
- ability to use driver model EEPROMs (uclass UCLASS_I2C_EEPROM)
- more flexible EEPROM layout support
It should not cause any behavior change for any existing board.
This series is a dependency for some DDR issue fixes for Turris Omnia.
I will be sending that one separately.
github PR link (with CI):
https://github.com/u-boot/u-boot/pull/540
- there is a failure for
test.py for sandbox sandbox_clang
but it seems unrelated to these changes
Add a new Kconfig option EEPROM_LAYOUT_VERSIONS, and hide eeprom
layout versionsing code behind it. Only print the relevant help in
'eeprom' command usage if this option is enabled.
Enable this new option for cm_fx6_defconfig and cm_t43_defconfig.
These are the only boards using EEPROM layout versioning.
Signed-off-by: Marek Behún <kabel@kernel.org>
CI: https://source.denx.de/u-boot/custodians/u-boot-imx/-/pipelines/20956
- Support different RAM sizes on imx8m phycoce boards.
- Support new toradex variants.
- Support Samsung 4GB DDR and Realtek RTL8211E PHY on imx8mm-cl-iot-gate.
- Convert imx8mm-phycore and imx8mp-phycore boards to use OF_UPSTREAM.
The PHYCORE_IMX8MP is used by the phyBOARD-Pollux. Migrate board to
OF_UPSTREAM. Linux kernel device tree for the board can be used as is,
corresponding U-Boot device tree files are removed. U-Boot tweaks are
kept unchanged.
Signed-off-by: Yannic Moog <y.moog@phytec.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Acked-by: Teresa Remmet <t.remmet@phytec.de>
The PHYCORE_IMX8MM is used by the phyBOARD-Polis and the
phyGATE-Tauri-L. Migrate both boards to OF_UPSTREAM. Linux kernel device
trees for both boards can be used as is, corresponding U-Boot device
tree files are removed. U-Boot tweaks are kept unchanged.
Signed-off-by: Yannic Moog <y.moog@phytec.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Acked-by: Teresa Remmet <t.remmet@phytec.de>
Enable OF_UPSTREAM to use upstream DT and add renesas/ prefix to the
DEFAULT_DEVICE_TREE. And thereby directly build DTB from dts/upstream/src/
including *-u-boot.dtsi files from arch/$(ARCH)/dts/ directory.
This patch finalizes OF_UPSTREAM conversion of R8A779H0 V4M which DTs
landed in Linux 6.9 .
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Acked-by: Sumit Garg <sumit.garg@linaro.org>
The ENV size and offset were changed to different
values in Beacon's downstream release. Change them to the
same values as the downstream for consistent behavior.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Javier Martinez Canillas <javier@dowhile0.org> says:
Hello,
I noticed that the IGEPv2 board did not boot anymore with mainline U-Boot.
This was caused by a driver change to allocate its platform data before
relocation and U-Boot not having enough pre-relocation heap size for this.
This series fixes this issue and also makes the board support more modern,
by enabling DM for SPL and migrating the IGEP boards to use upstream DTBs.
Enable OF_UPSTREAM to use upstream DT and add a ti/omap/ prefix to the
DEFAULT_DEVICE_TREE config option.
That way, a DTS from the upstream dts/upstream/src/ directory is used
instead of the arch/$(ARCH)/dts/ directory. These in turn are removed.
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Acked-by: Sumit Garg <sumit.garg@linaro.org>
Reviewed-by: Enric Balletbo i Serra <eballetbo@gmail.com>
This change is heavily based on commit e0cc7df9fd ("omap3_beagle: Update
for DM SPL support"), that did the same update for the OMAP3 Beagle board.
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Reviewed-by: Enric Balletbo i Serra <eballetbo@gmail.com>
There are no SPI peripherals in neither the IGEPv2 board nor the IGEP COM
Module, so there's no reason to have this enabled in the boards defconfig.
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Reviewed-by: Enric Balletbo i Serra <eballetbo@gmail.com>
The IGEPv2 board boot started to fail since the commit afd4f15a39 ("spi:
omap3_spi: Read platform data in ofdata_to_platdata()"). Because this made
the OMAP3 SPI controller driver to allocate its platform data before doing
a relocation, but the igep0x00 config sets this pool size to just 1 KiB.
Increase the pre-relocation malloc heap size to 16 KiB, as is set by other
OMAP3 boards. This not only restores booting but also makes it consistent.
Leave the SPL pool size to the previous 1 KiB size since 16 KiB may not be
a possible size in that constrained environment and is also the value that
is set by other OMAP3 boards.
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Reviewed-by: Enric Balletbo i Serra <eballetbo@gmail.com>
Use upstream device tree files and bindings. To do so:
- imply (enable) OF_UPSTREAM option for E850-96 target
- point DEFAULT_DEVICE_TREE in E850-96 config to upstream dts
- remove now not needed local dts files, binding docs and headers
- update MAINTAINERS and board/samsung/e850-96/MAINTAINERS
correspondingly
Upstream device tree files for Exynos850 SoC and E850-96 board are
pretty much the same as local (removed) ones, so the conversion is
rather straightforward and painless in this case. The appended dts file
(arch/arm/dts/exynos850-e850-96-u-boot.dtsi) stays unchanged.
The only remaining local dt-bindings doc for E850-96 board is
exynos-pmu.yaml. It wasn't removed as it's quite different from Linux
kernel version. Particularly U-Boot local version of exynos-pmu.yaml
describes "samsung,uart-debug-1" property, which is not present in Linux
kernel binding. Later it might be upstreamed to Linux kernel, and once
it's done the U-Boot exynos-pmu.yaml binding can be removed.
No functional change.
Acked-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
The Indiedroid Nova is a Rockchip RK3588S based SBC from Indiedroid.
Specifications:
Rockchip RK3588S SoC
4x ARM Cortex-A76, 4x ARM Cortex-A55
4/8/16GB memory LPDDR4x
Mali G610MC4 GPU
Optional eMMC
2x USB 2.0, 2x USB 3.0, 1x USB 3.0 C port with DP Alt
1x MIPI-CSI Port (4-lane or 2x 2-lane)
1x MIPI-DSI 4-lane connector
1x Micro HDMI 2.1 output, 1x DP 1.4 output
Gigabit Ethernet
Realtek RTL8821CS WiFi
4 pin debug UART connector
40 pin GPIO header
Size: 85mm x 56mm (Raspberry Pi Form Factor)
Kernel commit:
3900160e164b ("arm64: dts: rockchip: Add Indiedroid Nova board")
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The Powkiddy X55 is a Rockchip RK3566 based handheld gaming device.
UART, ADC, eMMC, and SDMMC are tested to work in U-Boot and this
successfully boots mainline Linux.
Kernel commit:
e99adc97e21a ("arm64: dts: rockchip: Add Powkiddy X55")
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Sughosh Ganu <sughosh.ganu@linaro.org> says:
The following patch series adds support for version 2 of the FWU
metadata. The version 2 metadata structure is defined in the latest
revision of the FWU specification [1].
The earlier versions of these patches were migrating to a version 2
only support in U-Boot, similar to TF-A. However, based on feedback
from ST [2], this series has been updated to support both versions. A
platform would still be needed to enable one of the two versions of
metadata through a config symbol.
TF-A has code which reads the FWU metadata and boots the platform from
the active partition. TF-A has decided to migrate the FWU code to a
version 2 only support. These changes have been merged in upstream
TF-A.
These changes have been tested on the ST DK2 board, which uses the GPT
based partitioning scheme. Both V1 and V2 metadata versions have been
tested on the DK2 board.
These changes need to be tested on platforms with MTD partitioned
storage devices.
Now that support for FWU metadata version 2 has been added, the
feature can be enabled on platforms which had enabled it. A new config
symbol for selecting the metadata version for the platform is also
being added.
Signed-off-by: Sughosh Ganu <sughosh.ganu@linaro.org>
Tested-by: Michal Simek <michal.simek@amd.com>
Support is to be added in the following commits for the FWU metadata
version 2. Disable the FWU feature on platforms that enable it for the
V2 addition work.
Signed-off-by: Sughosh Ganu <sughosh.ganu@linaro.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Tested-by: Michal Simek <michal.simek@amd.com>
By removing the "boot" directory in the "m53menlo/boot/fitImage" path,
we simplify the TFTP server directory layout a bit. This also requires a
change to the mmcload command as it (mis-)uses the same variable as the
TFTP boot.
Signed-off-by: Olaf Mandel <o.mandel@menlosystems.com>
Signed-off-by: Marek Vasut <marex@denx.de>
The board can do primary/secondary boot switching, enable the bmode command.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Synchronize Toradex Verdin iMX8MM based MX8Menlo board configuration
with Toradex Verdin iMX8MM and enable convenience commands like cat,
hexdump, xxd.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
U-Boot proper pre-reloc is currently running out of memory and it is
thus impossible to boot into U-Boot CLI.
Fix this by migrating to the common bss and stack addresses for PX30,
which drastically increases the size of the pre-reloc allocation pool (8
times bigger now). The memory layout in SPL and U-Boot proper now
match the other SoCs' using ROCKCHIP_COMMON_STACK_ADDR.
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Quentin Schulz <quentin.schulz@cherry.de>
This is the kind of setting that typically doesn't need to be changed
between boards based on the same SoC, so let's make it the default in
PX30 Kconfig so we don't have to care about it in the defconfig if we
don't want to.
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Quentin Schulz <quentin.schulz@cherry.de>
Migrate RV1126 boards that exists in Linux v6.8 to use OF_UPSTREAM.
Following targets is migrated to use OF_UPSTREAM:
- rv1126-edgeble-neu2 : Board is an industrial form factor
IO board.
- sonoff-ihost-rv1126 : Gateway device designed to provide a
Smart Home Hub.
Cc: Tim Lunn <tim@feathertop.org>
Cc: Jagan Teki <jagan@edgeble.ai>
Reviewed-By: Tim Lunn <tim@feathertop.org>
Tested-By: Tim Lunn <tim@feathertop.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Anand Moon <anand@edgeble.ai>
Signed-off-by: Anand Moon <linux.amoon@gmail.com>
As part of bringing the master branch back in to next, we need to allow
for all of these changes to exist here.
Reported-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Tom Rini <trini@konsulko.com>
When bringing in the series 'arm: dts: am62-beagleplay: Fix Beagleplay
Ethernet"' I failed to notice that b4 noticed it was based on next and
so took that as the base commit and merged that part of next to master.
This reverts commit c8ffd1356d, reversing
changes made to 2ee6f3a5f7.
Reported-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Tom Rini <trini@konsulko.com>
Add defconfig for AM68 SK R5 and A72 configuration.
This includes and modifies the AM68 EVM defconfigs:
j721s2_evm_r5_defconfig -> am68_sk_r5_defconfig
j721s2_evm_a72_defconfig -> am68_sk_a72_defconfig
Reviewed-by: Neha Malcom Francis <n-francis@ti.com>
Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
Switch to using bootstd. Note that with this change, we will stop using
distro_bootcmd and instead depend entirely on bootflow method of
starting the system up.
Also config_distro_bootcmd.h header file that is no longer needed in
j721s2_evm.h.
Signed-off-by: Neha Malcom Francis <n-francis@ti.com>
Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
u-boot-dfu-20240516
- Fix cdns3 low power hang via fast access bit
- Multiple dwc3 gadget fixes, mainly for USB support on TI AM6232
- Consistent USB_GADGET_MANUFACTURER for PHYTEC boards
- MAINTAINERS file update for u-boot-dfu
Martyn Welch <martyn.welch@collabora.com> says:
This series adds DFU support for TI AM62 SK and beagleplay boards.
I have picked this series up from Sjoerd due to time constraints.
Since the last revision:
* Removed dwc3 mode setting in favour of reinstating forced peripheral
mode for usb0
* Use of config fragments for both r5 and a53 DFU configuration to
reduce duplication
* Typographical improvements to documentation
We plan to also submit the dts changes to linux so that those can be
dropped again in the near future (hopefully)
DFU mode on a beagleplay can be used via the Type-C connector by holding
the USR switch while powering on.
Configuration is already provided as fragments for both the A53 and R5
u-boot parts. Include the am62x_a53_usbdfu.config config. The
am62x_r5_usbdfu.config fragment needs to be added should DFU boot be
required as this will disable booting from persistent storage due to
binary size constraints.
Signed-off-by: Sjoerd Simons <sjoerd@collabora.com>
Signed-off-by: Martyn Welch <martyn.welch@collabora.com>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Tested-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Provide config fragments to enable USB host as well as USB gadget and DFU
support for a53 and r5. This relevant fragment is included into the
am62x EVM a53 defconfig. For the r5, due to the smaller available size,
the config fragment also disables support for persistent storage to free
up space for USB support. This fragment needs to be included is DFU
booting is desired.
The CONFIG_DFU_SF option is placed in the defconfig rather than the
fragment as this is known not to be supported on all boards that can
support DFU.
Signed-off-by: Sjoerd Simons <sjoerd@collabora.com>
Signed-off-by: Martyn Welch <martyn.welch@collabora.com>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
We can use U-Boot for recovering JH7110 based boards via UART
if CONFIG_SPL_YMODEM_SUPPORT=y.
* Send u-boot-spl.normal.out via XMODEM.
* Send u-boot.itb via YMODEM.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: E. Shattow <lucent@gmail.com>
