In cdns_torrent_phy_probe the test for too many lanes configured does
not set an error code before taking the error path. This could lead to a
silent failure if the calling code does not detect the error. Add the
code to return -EINVAL in this case.
This issue was found by Smatch.
Signed-off-by: Andrew Goodbody <andrew.goodbody@linaro.org>
In cdns_sierra_pll_bind_of_clocks the variable 'i' is declared but never
assigned to before its value is used in a dev_err. Replace clk_names[i]
by the name passed to device_bind(), i.e., "pll_mux_clk". With that, the
clk_names[] array is unused and can therefore be removed.
This issue was found by Smatch.
Signed-off-by: Andrew Goodbody <andrew.goodbody@linaro.org>
[jf: update description]
Signed-off-by: Jerome Forissier <jerome.forissier@linaro.org>
In comphy_cp110_init_serdes_map in comphy_cp110.c there are two fields
in cfg, comphy_lanes_count and comphy_mux_bitcount, which are fetched
from the FDT blob with fdtdec_get_int which returns an int. These two
fields are then tested for being negative. However the fields are
declared as unsigned so those tests must always fail. Change the
declaration of those fields to be int instead of u32 and the code will
work as expected.
This issue was found by Smatch.
Signed-off-by: Andrew Goodbody <andrew.goodbody@linaro.org>
Reviewed-by: Stefan Roese <stefan.roese@mailbox.org>
The limit checks in get_speed_string and get_type_string are off by 1 as
they do not account for the maximum index into an array that can be used
is 1 less than the number of elements in that array. Adjust the limit
checks to allow for this.
This issue was found by Smatch.
Signed-off-by: Andrew Goodbody <andrew.goodbody@linaro.org>
Reviewed-by: Stefan Roese <stefan.roese@mailbox.org>
Add DM driver for Exynos USB PHY controllers. For now it only supports
Exynos850 SoC. Only UTMI+ (USB 2.0) PHY interface is implemented, as
Exynos850 doesn't support USB 3.0. Only two clocks are used for this
controller:
- phy: bus clock, used for PHY registers access
- ref: PHY reference clock (OSCCLK)
Ported from Linux kernel: drivers/phy/samsung/phy-exynos5-usbdrd.c
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@kernel.org>
Reviewed-by: Minkyu Kang <mk7.kang@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This is a port of the corresponding commit in the Linux kernel which
adds the same support for the Cadence Torrent driver[0]. The commit
message below is taken as-is from the Linux kernel commit being ported.
The Torrent SERDES can support at most two different protocols (PHY types).
This only mandates that the device-tree sub-nodes used to represent the
configuration should describe links with at-most two different protocols.
The existing implementation however imposes an artificial constraint that
allows only two links (device-tree sub-nodes). As long as at-most two
protocols are chosen, using more than two links to describe them in an
alternating configuration is still a valid configuration of the Torrent
SERDES.
A 3-Link 2-Protocol configuration of the 4-Lane SERDES can be:
Lane 0 => Protocol 1 => Link 1
Lane 1 => Protocol 1 => Link 1
Lane 2 => Protocol 2 => Link 2
Lane 3 => Protocol 1 => Link 3
A 4-Link 2-Protocol configuration of the 4-Lane SERDES can be:
Lane 0 => Protocol 1 => Link 1
Lane 1 => Protocol 2 => Link 2
Lane 2 => Protocol 1 => Link 3
Lane 3 => Protocol 2 => Link 4
[0] 5b7b83a983
Signed-off-by: Hrushikesh Salunke <h-salunke@ti.com>
E Shattow <e@freeshell.de> says:
Make consistent use of lowercase hexadecimal prefix '0x' throughout U-Boot.
There are a few remaining uses of uppercase 'X' to denote hexadecimal prefix
or placeholder in documentation and error messages.
External devicetree-rebasing dts/upstream and the generated code of
xilinx/zynq are ignored for the series.
Link: https://lore.kernel.org/r/20250606224558.1117422-1-e@freeshell.de
Use consistent lowercase hex prefix style in drivers/*
Does not change hex prefix case in allcaps uppercase style error messages
Signed-off-by: E Shattow <e@freeshell.de>
The bitshift in GEM_CLK_CTRL register is five bits, not two. There are
four bits for each GEM, and one bit reserved in between.
This has caused that using more than one GEM is impossible,
additionally corrupting the GEM0's configuration, leaving GEM0
unusable as well (ie. if GEM0 and GEM1 are used, GEM1 configuration is
going to write to GEM0's registers wrong value, leaving GEM0 unusable)
Signed-off-by: Frantisek Bohacek <rutherther@ditigal.xyz>
Link: https://lore.kernel.org/r/20250522060703.4863-1-rutherther@ditigal.xyz
Signed-off-by: Michal Simek <michal.simek@amd.com>
So far Allwinner boards controlled the USB OTG ID detection via the
respective GPIO pin specified in Kconfig, as a string. All boards should
have the same GPIO already specified in the devicetree, in the
usb0_id_det-gpios property.
Convert the usage of the Kconfig configured GPIO over to query that
information from the devicetree, then use the existing DM GPIO
infrastructure to request the GPIO.
Only PHY0 supports USB-OTG, so limit the GPIO request to that PHY, to
avoid claiming it multiple times.
This removes the need to name that GPIO in the defconfig file.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
So far Allwinner boards controlled the USB VBUS detection via the
respective GPIO pin specified in Kconfig, as a string. All boards should
have the same GPIO already specified in the devicetree, in the
usb0_vbus_det-gpios property.
Convert the usage of the Kconfig configured GPIO over to query that
information from the devicetree, then use the existing DM GPIO
infrastructure to request the GPIO.
Only PHY0 supports USB-OTG, so limit the GPIO request to that PHY, to
avoid claiming it multiple times.
This removes the need to name that GPIO in the defconfig file.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
The device tree binding for the PHY provides VBUS supplies as regulator
references. Now that all boards have the appropriate regulator uclass
drivers enabled, the PHY driver can switch to using them. This replaces
direct GPIO usage, which in some cases needed a special DM-incompatible
"virtual" GPIO from the PMIC.
The following boards provided a value for CONFIG_USB0_VBUS_PIN, but are
missing the "usb0_vbus-supply" property in their device tree. None of
them have the MUSB controller enabled in host or OTG mode, so they
should see no impact:
- Ainol_AW1_defconfig / sun7i-a20-ainol-aw1
- Ampe_A76_defconfig / sun5i-a13-ampe-a76
- CHIP_pro_defconfig / sun5i-gr8-chip-pro
- Cubieboard4_defconfig / sun9i-a80-cubieboard4
- Merrii_A80_Optimus_defconfig / sun9i-a80-optimus
- Sunchip_CX-A99_defconfig / sun9i-a80-cx-a99
- Yones_Toptech_BD1078_defconfig / sun7i-a20-yones-toptech-bd1078
- Yones_Toptech_BS1078_V2_defconfig /
sun6i-a31s-yones-toptech-bs1078-v2
- iNet_3F_defconfig / sun4i-a10-inet-3f
- iNet_3W_defconfig / sun4i-a10-inet-3w
- iNet_86VS_defconfig / sun5i-a13-inet-86vs
- iNet_D978_rev2_defconfig / sun8i-a33-inet-d978-rev2
- icnova-a20-swac_defconfig / sun7i-a20-icnova-swac
- sun8i_a23_evb_defconfig / sun8i-a23-evb
Similarly, the following boards set CONFIG_USB1_VBUS_PIN, but do not
have "usb1_vbus-supply" in their device tree. Neither of them have USB
enabled at all, so again there should be no impact:
- Cubieboard4_defconfig / sun9i-a80-cubieboard4 (also for USB3)
- sun8i_a23_evb_defconfig / sun8i-a23-evb
The following boards use a different pin for USB1 VBUS between their
defconfig and their device tree. Depending on which is correct, they
may be broken:
- Linksprite_pcDuino3_Nano_defconfig (PH11) /
sun7i-a20-pcduino3-nano (PD2)
- icnova-a20-swac_defconfig (PG10) / sun7i-a20-icnova-swac (PH6)
Finally, this board has conflicting pins given for its USB2 VBUS:
- Lamobo_R1_defconfig (PH3) / sun7i-a20-lamobo-r1 (PH12)
Signed-off-by: Samuel Holland <samuel@sholland.org>
[Andre: use regulator_set_enable_if_allowed()]
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
The 480m clk is controlled using regs in the PHY address space and not
in the USB GRF address space on e.g. RK3528 and RK3506.
Add a clkout_ctl_phy usb2phy_reg to handle enable/disable of the 480m
clk on these SoCs.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Tom Rini <trini@konsulko.com> says:
This series switches to always using $(PHASE_) in Makefiles when
building rather than $(PHASE_) or $(XPL_). It also starts on documenting
this part of the build, but as a follow-up we need to rename
doc/develop/spl.rst and expand on explaining things a bit.
Link: https://lore.kernel.org/r/20250401225851.1125678-1-trini@konsulko.com
It is confusing to have both "$(PHASE_)" and "$(XPL_)" be used in our
Makefiles as part of the macros to determine when to do something in our
Makefiles based on what phase of the build we are in. For consistency,
bring this down to a single macro and use "$(PHASE_)" only.
Signed-off-by: Tom Rini <trini@konsulko.com>
Recent addition of support for SDM660 inadvertently broke USB PHY power
on sequence on RB1/RB2 and others with following error:
starting USB...
Bus usb@4e00000: QUSB2PHY pll lock failed: status reg = 0
qcom-qusb2-phy phy@1613000: PHY: Failed to power on phy@1613000: -16.
Can't power on PHY0
probe failed, error -16
No USB controllers found
The root cause was the addition of flag se_clk_scheme_default which was
configured correctly for SDM660 but incorrect for all other supported
SoC. Fix that by properly assignment as per upstream Linux driver.
Fixes: 475497dc3c15 ("phy: Add SDM660 support to Qualcomm QUSB2 phy")
Signed-off-by: Sumit Garg <sumit.garg@oss.qualcomm.com>
Reviewed-by:
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20250410080027.208674-3-sumit.garg@kernel.org
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Extend the existing Renesas R-Car Gen3 USB 2.0 PHY driver to support the
RZ/G2L and related SoCs.
Also enable this driver by default for the RZ/G2L SoC family.
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Signed-off-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Cdns core driver also get dr mode from wrapper devcie dts node
to make it is same with Starfive cdns USB Linux kernel driver,
Starfive 7110 OF_UPSTREAM is enabled
Signed-off-by: Minda Chen <minda.chen@starfivetech.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Add Starfive JH7110 PCIe 2.0 PHY driver, which is generic
PHY driver and can be used as USB 3.0 driver.
Signed-off-by: Minda Chen <minda.chen@starfivetech.com>
Tested-by: E Shattow <lucent@gmail.com>
In generic_phy_get_bulk(), if 'phys' property is absent in
the device node then it is not an error condition.
Change print message verbosity to debug to avoid spamming
console in such cases.
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Reviewed-by: Siddharth Vadapalli <s-vadapalli@ti.com>
The correct spelling is R-Car, including the dash, update the usage.
Comment changes only, no functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
The ufsphy_v2_regs_layout is not used, drop it and fix:
phy-qcom-qmp-ufs.c:87:27: warning: ‘ufsphy_v2_regs_layout’ defined but not used [-Wunused-const-variable=]
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Caleb Connolly <caleb.connolly@linaro.org>
Simon Glass <sjg@chromium.org> says:
When the SPL build-phase was first created it was designed to solve a
particular problem (the need to init SDRAM so that U-Boot proper could
be loaded). It has since expanded to become an important part of U-Boot,
with three phases now present: TPL, VPL and SPL
Due to this history, the term 'SPL' is used to mean both a particular
phase (the one before U-Boot proper) and all the non-proper phases.
This has become confusing.
For a similar reason CONFIG_SPL_BUILD is set to 'y' for all 'SPL'
phases, not just SPL. So code which can only be compiled for actual SPL,
for example, must use something like this:
#if defined(CONFIG_SPL_BUILD) && !defined(CONFIG_TPL_BUILD)
In Makefiles we have similar issues. SPL_ has been used as a variable
which expands to either SPL_ or nothing, to chose between options like
CONFIG_BLK and CONFIG_SPL_BLK. When TPL appeared, a new SPL_TPL variable
was created which expanded to 'SPL_', 'TPL_' or nothing. Later it was
updated to support 'VPL_' as well.
This series starts a change in terminology and usage to resolve the
above issues:
- The word 'xPL' is used instead of 'SPL' to mean a non-proper build
- A new CONFIG_XPL_BUILD define indicates that the current build is an
'xPL' build
- The existing CONFIG_SPL_BUILD is changed to mean SPL; it is not now
defined for TPL and VPL phases
- The existing SPL_ Makefile variable is renamed to SPL_
- The existing SPL_TPL Makefile variable is renamed to PHASE_
It should be noted that xpl_phase() can generally be used instead of
the above CONFIGs without a code-space or run-time penalty.
This series does not attempt to convert all of U-Boot to use this new
terminology but it makes a start. In particular, renaming spl.h and
common/spl seems like a bridge too far at this point.
The series is fully bisectable. It has also been checked to ensure there
are no code-size changes on any commit.
Add Qualcomm QMP UFS PHY driver which is available on the following
Snapdragon SoCs - SDM845, SM8250, SM8550 and SM8650 SoCs.
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@linaro.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Import Qualcomm QMP phy related header files from Linux v6.11-rc7,
limit to headers needed to setup QMP v2 to v6 UFS PHYs.
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@linaro.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
use dev_dbg() instead of dev_info() for debug related
prints.
Get's rid of below print from console.
"cdns,sierra serdes@5030000: sierra probed"
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Implement trivial extension to the sandbox PHY, which makes it pretend
to support selecting USB Host mode and nothing else. Any other mode is
rejected with -EINVAL. Any submode except for default submode 0 is
rejected with -EOPNOTSUPP . The implementation behaves in this trivial
way to permit easy unit testing using test which is also added in this
commit.
To run the test, use e.g. sandbox64_defconfig and run U-Boot as follows:
$ ./u-boot -Tc 'ut dm phy_setup'
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
The current init operation also sets the PHY into USB host mode.
Split the mode configuration into set_mode callback instead and
implement support for device and OTG modes as well.
The OTG mode performs auto-detection and selects either host or
device mode. In case the OTG mode is configured, submode field
can be used to select full PHY (re)initialization or only mode
auto-detection. The full (re)initialization is only necessary
once, on start up.
Since the OTG mode may enable IRQ generation in the PHY, disable
that IRQ generation in the exit callback again.
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Extend generic_setup_phy() parameter list with PHY mode and submode and
call generic_phy_set_mode() in generic_setup_phy(), so the generic PHY
setup function can configure the PHY into correct mode before powering
the PHY up.
Update all call sites of generic_setup_phy() as well, all of which are
USB host related, except for DM test which now behaves as a USB host
test.
Note that if the PHY driver does not implement the .set_mode callback,
generic_phy_set_mode() call returns 0 and does not error out, so this
should not break any existing systems.
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Fix multiplex configuration for PCIe1L0 and PCIe1L1 in PCIESEL_CON for
RK3588 to correctly select between Combo PHYs and PCIe3 PHY.
Currently, the code incorrectly muxes both ports to Combo PHYs,
interfering with PCIe3 PHY settings.
Introduce PHY identifiers to identify the correct Combo PHY and set
the necessary bits accordingly.
This fix is adapted from the upstream Linux commit by Sebastian Reichel:
d16d4002fea6 ("phy: rockchip: naneng-combphy: Fix mux on rk3588")
Fixes: b37260bca1 ("phy: rockchip: naneng-combphy: Use signal from comb PHY on RK3588")
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Sebastian Kropatsch <seb-dev@mail.de>
The pcie1ln_sel bits for the RK3588 are getting set but not cleared due
to an incorrect write mask.
Use a newly introduced constant for the write mask to fix this.
Also introduce a GENMASK-based constant for PCIE30_PHY_MODE.
This fix is adapted from the upstream Linux commit by Sebastian Reichel:
55491a5fa163 ("phy: rockchip-snps-pcie3: fix clearing PHP_GRF_PCIESEL_CON bits")
Fixes: 50e54e8067 ("phy: rockchip: snps-pcie3: Add support for RK3588")
Signed-off-by: Sebastian Kropatsch <seb-dev@mail.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Misconfigured `PHP_GRF_PCIESEL` values are causing bifurcation issues,
for example on the FriendlyElec CM3588 NAS board which uses bifurcation
on both PCIe PCIe ports (all four lanes) to enable four M.2 NVMe
sockets. Without this fix, NVMe devices do not get recognized.
Correct the `PHP_GRF_PCIESEL` register configuration and simplify the
bifurcation logic, enabling proper PCIe bifurcation based on the
data-lanes property.
This fix is adapted from the upstream Linux commit by Michal Tomek:
f8020dfb311d ("phy: rockchip-snps-pcie3: fix bifurcation on rk3588")
Fixes: 50e54e8067 ("phy: rockchip: snps-pcie3: Add support for RK3588")
Signed-off-by: Sebastian Kropatsch <seb-dev@mail.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Several identifiers use "rochchip" instead of "rockchip".
Fix this by replacing every instance of "rochchip" with "rockchip".
Signed-off-by: Sebastian Kropatsch <seb-dev@mail.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
inno_poll passes the reg offset that is used by readl_poll_sleep_timeout
without any base addr.
Fix it.
Bug:
inno_hdmi_phy phy@ff430000: Pre-PLL locking failed
inno_hdmi_phy phy@ff430000: PHY: Failed to power on phy@ff430000: -110.
failed to power on phy (ret=-110)
inno_hdmi_phy phy@ff430000: Pre-PLL locking failed
inno_hdmi_phy phy@ff430000: PHY: Failed to power on phy@ff430000: -110.
failed to power on phy (ret=-110)
Fixes: aa22711846 ("phy: rockchip: Add Rockchip INNO HDMI PHY driver")
Suggested-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Jagan Teki <jagan@edgeble.ai>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
