Commit 86acdce2ba ("common: add config for board_init() call")
introduced CONFIG_BOARD_INIT option. This option can be disabled for the
boards where board_init() function is not needed. Remove empty
board_init() calls for all boards where it's possible, and disable
CONFIG_BOARD_INIT in all related defconfigs.
This cleanup was made semi-automatically using these scripts: [1].
No functional change, but the binary size for the modified boards is
reduced a bit.
[1] https://github.com/joe-skb7/uboot-convert-scripts/tree/master/remove-board-init
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Tested-by: Adam Ford <aford173@gmail.com> #imx8mm_beacon
Tested-by: Bryan Brattlof <bb@ti.com>
Acked-by: Peng Fan <peng.fan@nxp.com> #NXP boards
Hrushikesh Salunke <h-salunke@ti.com> says:
This series adds support for the Endpoint mode on Cadence PCIe controller
on TI's K3 family of SoCs. The driver is an adaptation of the Linux
driver (drivers/pci/controller/cadence/pci-j721e.c) and has been
implemented specifically for Endpoint mode of operation on AM64X. A minor
set of changes will be sufficient to support other K3 SoCs as well.
This patch is tested on AM64X EVM. Following are the log corresponding
to this feature.
https://gist.github.com/hrushikesh221/e8557cbe7667877c50f7d7e9bb96d060
Link: https://lore.kernel.org/r/20250616164929.631791-1-h-salunke@ti.com
TI's AM64x SoC has a single instance of PCIe Controller namely PCIe0
which is a Cadence PCIe Controller. To support PCI Endpoint
functionality with the PCIe0 instance of PCIe, enable the corresponding
configs.
Signed-off-by: Hrushikesh Salunke <h-salunke@ti.com>
Use default value of malloc size coming from Kconfig, instead of
board specific override.
Signed-off-by: Udit Kumar <u-kumar1@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Enable UHS modes for SD by enabling configs for voltage regulator
drivers, IO voltage switching, and configs to support UHS modes.
The am64x SoC has an internal LDO which does voltage switching,
but the MMC_IO_VOLTAGE config is still required to be able to
switch voltage for SD.
While we are here, am64x HS400 mode has been descoped as per
datasheet [0] even though we still initialize to HS200, clean
this up by switching to MMC_HS200_SUPPORT config options.
[0] https://www.ti.com/lit/gpn/am6442
Signed-off-by: Judith Mendez <jm@ti.com>
TI's AM64 SoC has single instance of PCIe Controller namely PCIe0 which
is Cadence PCIe Controller. To support PCIe functionality with PCIe0
instance in Root-Complex mode enable corresponding configs. Also enable
configs to support NVMe over PCIe.
Signed-off-by: Hrushikesh Salunke <h-salunke@ti.com>
Reviewed-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Add TI_COMMON_CMD_OPTIONS config options to Sitara K3 boards at
a53 stage since we rely on most of the commands implied for testing
and debugging purposes. Since all commands are now enabled by
default, remove the redundant CMD_* options in the a53 defconfigs.
Also add MMC_REG & MMC_SPEED_MODE_SET useful commands to
TI_COMMON_CMD_OPTIONS.
Signed-off-by: Judith Mendez <jm@ti.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
SPL_TEXT_BASE is used as the load address for the main domain SPL on k3
platforms.
Since the config value is the same for every board, this patch sets the
value 0x80080000 as default for all 64-bit ARCH_K3, 0x43c00000 as
default for the R5 cores and deletes the instances of SPL_TEXT_BASE in
individual defconfigs.
Signed-off-by: Anshul Dalal <anshuld@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Enable support for USB mass storage class (UMS) via USB0 instance of
USB on AM64x SoC. UMS allows USB host to access U-Boot block device
and enable file transfer.
Example usage of UMS command :
=> mmc list
mmc@fa10000: 0 (eMMC)
mmc@fa00000: 1
=> ums 0 mmc 1
UMS: LUN 0, dev mmc 1, hwpart 0, sector 0x0, count 0x3b72400
Signed-off-by: Hrushikesh Salunke <h-salunke@ti.com>
Judith Mendez <jm@ti.com> says:
Some K3 devices like am62x and am64x have a M4 processor in the MCU
voltage domain. This patch series introduces remoteproc M4 driver which
will be used to load firmware into and start the M4 remote core.
This series also adds support for R5F cores on am64x SoCs in patch 2 and
sets up environment to load FW in remote cores in patch 3,4,5.
This patch series also enables remoteproc drivers by default as per what
remoteproc sybsystem is supported per SoC, thus all remoteproc options
are now deleted in configs/* since they are no longer required.
This patch series was tested on am64x EVM, am62x SK, am62ax SK,
am62px SK boards.
Any additional tested by's are welcome since I was not able to
test any additional boards.
Tested by running the following commands in u-boot prompt:
=> setenv dorprocboot 1
=> run boot_rprocs
Link: https://lore.kernel.org/r/20250210202944.1071931-1-jm@ti.com
Now that remoteproc configs are enabled by default in Kconfig
files, remove these configs which are no longer needed to be
defined here in configs/.
Signed-off-by: Judith Mendez <jm@ti.com>
Reviewed-by: Andrew Davis <afd@ti.com>
Set CONFIG_NR_DRAM_BANKS to 2 as we have two banks described in the
memory/ node for lower and higher addressible DDR regions.
This allows use of FDT functions from fdt_support.c to set up and fix up
the memory/ node correctly.
Signed-off-by: Neha Malcom Francis <n-francis@ti.com>
Signed-off-by: Santhosh Kumar K <s-k6@ti.com>
Make the raw-mode options depend on SPL_SYS_MMCSD_RAW_MODE in a more
direct way. This makes it easier to understand the options with
'make menuconfig'.
There are three different ways of specifying the offset:
- sector offset
- partition number
- partition type
So make these a choice, so it is more obvious what is going on.
Update existing boards to enable SPL_SYS_MMCSD_RAW_MODE where needed.
Reviewed-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Quentin Schulz <quentin.schulz@cherry.de>
Signed-off-by: Simon Glass <sjg@chromium.org>
The board has the TCA9554 I2C GPIO expander chip for expansion
board presence detection logic.
Enable the relevant I2C GPIO drivers.
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Enable ICSSG driver, DP83869 phy driver, REMOTEPROC and PRU_REMOTEPROC
in am64x_evm_a53_defconfig. All these configs are needed for ICSSG
driver.
Signed-off-by: MD Danish Anwar <danishanwar@ti.com>
EMMC boot can fail due to the size of R5 SPL image growing beyond the
500KB of memory allocated in eMMC. Update offsets for eMMMC raw boot
to load each binary from the correct address in eMMC according to the
following eMMC layout:
boot0/1 partition
0x0+----------------------------------+
| tiboot3.bin (1 MB) |
0x800+----------------------------------+
| tispl.bin (2 MB) |
0x1800+-----------------------------------+
| u-boot.img (4 MB) |
0x3800+-----------------------------------+
| environment (128 KB) |
0x3900+-----------------------------------+
Signed-off-by: Judith Mendez <jm@ti.com>
Jonathan Humphreys <j-humphreys@ti.com> says:
Set basic settings needed for System Ready IR ACS testing, for several TI SoC
based platforms: AM64, AM62, AM62p, BeaglePlay, J7, and BeagleboneAI.
For AM64, AM62, and AM62p, also includes some config cleanup. Should be no
functional change.
Enable OF_UPSTREAM for AM64-EVM and SK-AM64 boards. Remove DT files that
are now available in dts/upstream. Update the appended files based on
version of latest OF_UPSTREAM sync point (v6.7-rc7).
Signed-off-by: Andrew Davis <afd@ti.com>
The help for CONFIG_MTD explains that it needs to be enabled for various
things like NAND, etc to be available. It however then doesn't enforce
this dependency and so if you have none of these systems present you
still need to disable a number of options. Fix this by making places
that select/imply one type of flash, but did not do the same, also do
this for "MTD". Make boards which hadn't been enabling MTD already but
need it now, do so. In a few places, disable CONFIG_CMD_MTDPARTS as it
wasn't previously enabled but was now being implied.
Signed-off-by: Tom Rini <trini@konsulko.com>
Switch to using bootstd. Note with this change, we will stop using
distro_bootcmd and instead depend entirely on bootflow method of
starting the system up.
Drop header files that are no longer needed in am64x_evm.h.
k3_dfu.h is available via k3_dfu.env in am64x.env.
Drop unused macro CFG_SYS_SDRAM_BASE1.
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Reviewed-by: Nishanth Menon <nm@ti.com>
All K3 boards now are secure by default, instead of setting this in each
defconfig, make it implied by the ARCH config.
The only exception is IOT2050, which I do not believe will have any
problems with being a TI_SECURE_DEVICE, but for now turn it off to keep
its config the same.
Signed-off-by: Andrew Davis <afd@ti.com>
Tested-by: Tom Rini <trini@konsulko.com>
We like to put the SPL first so it is clear that it relates to SPL. Rename
various malloc-related options which have crept in, to stick to this
convention.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Martyn Welch <martyn.welch@collabora.com>
Reviewed-by: Svyatoslav Ryhel <clamor95@gmail.com>
Do not limit the maximum size of the buffer that is used to decompress
the OS image in to, this causes issue while inflating the image, if image
size is greater than the buffer.
Remove CONFIG_SYS_BOOTM_LEN
Signed-off-by: Kamlesh Gurudasani <kamlesh@ti.com>
Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
Default to common bootcmd that is set across all k3 devices.
Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
Signed-off-by: Kamlesh Gurudasani <kamlesh@ti.com>
Having saved environments usually causes inconsistencies while in
development workflow. The saved environments conflict with the
default ones that U-boot should be updating during development
but that doesn't happen and the saved environments need to be
reset during bootups to test the changes causing extra debugs.
Remove the saved environments as a default. Environments can always
be re-enabled locally if one does like them or needs them for
some production environment. Optionally, Uenv.txt can also be used on
some of the boot media.
Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
This converts the following to Kconfig:
CONFIG_SYS_BOOTM_LEN
As part of this, rework error handling in boot/bootm.c so that we pass
the buffer size to handle_decomp_error as CONFIG_SYS_BOOTM_LEN will not
be available to host tools but we do know the size that we passed to
malloc().
Cc: Soeren Moch <smoch@web.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SYS_SPL_MALLOC_SIZE
CONFIG_SYS_SPL_MALLOC_START
We introduce a default value here as well, and CONFIG_SYS_SPL_MALLOC to
control if we have a malloc pool or not.
Signed-off-by: Tom Rini <trini@konsulko.com>
