This allows to test if a pin's label if displayed using gpio_get_status()
when this pin is configured in alternate function.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Even pin with GPIOF_UNUSED function can have a label.
The criteria to add or not a space character is linked to label not to
the used/unused status.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
The nvme driver falsely assumed that the last entry on a page
of the prp-list always points to the next page of the prp-list.
This potentially can lead to the illegal creation of pages on
the prp-list with only a single entry. This change now ensures
that splitting the prp-list into multiple pages, behaves now as
required by the NVME-Spec.
Related to this, also the size of the memory allocation is adjusted
accordingly.
Signed-off-by: Alexander Sowarka <alexander.sowarka@aerq.com>
Functions stm32_i2c_message_start and stm32_i2c_handle_reload
both get a stop boolean indicating if the transfer should end with
a STOP or not. However no specific handling is needed in those
functions hence remove the parameter.
Signed-off-by: Alain Volmat <alain.volmat@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Comment within stm32_i2c_message_start is misleading, indicating
that AUTOEND bit is setted while it is actually cleared.
Moreover, the bit is actually never setted so there is no need
to clear it hence get rid of this bit clear and the bit macro
as well.
Signed-off-by: Alain Volmat <alain.volmat@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
This change defines resources for OP-TEE service drivers to register
themselves for being bound to when OP-TEE firmware reports the related
service is supported. OP-TEE services are discovered during optee
driver probe sequence which mandates optee driver is always probe once
bound.
Discovery of optee services and binding to related U-Boot drivers is
embedded upon configuration switch CONFIG_OPTEE_SERVICE_DISCOVERY.
Cc: Jens Wiklander <jens.wiklander@linaro.org>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Signed-off-by: Etienne Carriere <etienne.carriere@linaro.org>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Add functions to read 8/16-bit integers like the existing functions for
32/64-bit to simplify read of 8/16-bit integers from device tree
properties.
Signed-off-by: Stefan Herbrechtsmeier <stefan.herbrechtsmeier@weidmueller.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add ID for Winbond W25Q512JVQ device which is supported
on AST2600 EVB by default.
Signed-off-by: Chin-Ting Kuo <chin-ting_kuo@aspeedtech.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Driver can configure the SPI clock frequnecy to the
target value of "spi-max-frequency" property in
the device tree. The frequency is divided from HCLK,
200MHz. Usually, the ASPEED SPI clock frequency range
is between 12.5MHz and 100MHz. On AST2600, the lowest
SPI clock frequency can be about 780kHz.
Signed-off-by: Chin-Ting Kuo <chin-ting_kuo@aspeedtech.com>
There are some known HW problems about decoded
range register configurations on existing AST2500 and
AST2600 platforms. Additional callback function,
adjust_decoded_sz, is added to solve these problems
on each platform. Besides, aspeed_spi_trim_decoded_size
function is added to modify overall decoded address
size for fitting the maximum AHB decoded size.
Signed-off-by: Chin-Ting Kuo <chin-ting_kuo@aspeedtech.com>
From the HW point of view, the performance of
command read mode is greater than user mode slightly.
Thus, dirmap read framework is introduced to achieve
this goal. In dirmap_create, command read mode is
configured. Usually, the decoded address area with flash
size is assigned to each CS. CPU can thus access the
SPI flash as normal memory in dirmap_read function.
Signed-off-by: Chin-Ting Kuo <chin-ting_kuo@aspeedtech.com>
This adds the dirmap API originally introduced in
Linux commit aa167f3fed0c
("spi: spi-mem: Add a new API to support direct mapping").
This also includes several follow-up patches and fixes.
Changes from Linux include:
* Added Kconfig option
* Changed struct device to struct udevice
* Changed struct spi_mem to struct spi_slave
This patch is obtained from the following patch
https://patchwork.ozlabs.org/project/uboot/patch/20210205043924.149504-3-seanga2@gmail.com/
The corresponding Linux kernel SHA1 is aa167f3fed0c.
Signed-off-by: Chin-Ting Kuo <chin-ting_kuo@aspeedtech.com>
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Acked-by: Pratyush Yadav <p.yadav@ti.com>
Although AST2400 is EOL officially, in order to achieve
sustainability and completeness, AST2400 part is added.
For AST2400,
- Five CSs are supported by FMC controller.
- SPI1 controller only supports single CS and there is
no address segment address register. The CE control
register of SPI1 is located at the offset 0x04 and
the 4-byte address mode control bit is bit 13 of
this register.
Signed-off-by: Chin-Ting Kuo <chin-ting_kuo@aspeedtech.com>
Add ASPEED BMC FMC/SPI memory controller driver with
spi-mem interface for AST2500 and AST2600 platform.
There are three SPI memory controllers embedded in an ASPEED SoC.
- FMC: Named as Firmware Memory Controller. After AC on, MCU ROM
fetches initial device boot image from FMC chip select(CS) 0.
- SPI1: Play the role of a SPI Master controller. Or, there is a
dedicated path for HOST(X86) to access its BIOS flash mounted
under BMC. spi-aspeed-smc.c implements the control sequence when
SPI1 is a SPI master.
- SPI2: It is a pure SPI flash controller. For most scenarios, flashes
mounted under it are for pure storage purpose.
ASPEED SPI controller supports 1-1-1, 1-1-2 and 1-1-4 SPI flash mode.
Three types of command mode are supported, normal mode, command
read/write mode and user mode.
- Normal mode: Default mode. After power on, normal read command 03h or
13h is used to fetch boot image from SPI flash.
- AST2500: Only 03h command can be used after power on
or reset.
- AST2600: If FMC04[6:4] is set, 13h command is used,
otherwise, 03h command.
The address length is decided by FMC04[2:0].
- Command mode: SPI controller can send command and address
automatically when CPU read/write the related remapped
or decoded address area. The command used by this mode
can be configured by FMC10/14/18[23:16]. Also, the
address length is decided by FMC04[2:0]. This mode will
be implemented in the following patch series.
- User mode: It is a traditional and pure SPI operation, where
SPI transmission is controlled by CPU. It is the main
mode in this patch.
Each SPI controller in ASPEED SoC has its own decoded address mapping.
Within each SPI controller decoded address, driver can assign a specific
address region for each CS of a SPI controller. The decoded address
cannot overlap to each other. With normal mode and command mode, the
decoded address accessed by the CPU determines which CS is active.
When user mode is adopted, the CS decoded address is a FIFO, CPU can
send/receive any SPI transmission by accessing the related decoded
address for the target CS.
This patch only implements user mode initially. Command read/write
mode will be implemented in the following patches.
Signed-off-by: Chin-Ting Kuo <chin-ting_kuo@aspeedtech.com>
Add FWSPICS1 and SPI1CS1 in AST2500 pinctrl group.
On AST2500 EVB, FWSPICS1 can be supported by default.
An extra jumper, J45, should be configured before
enabling SPI1CS1.
Signed-off-by: Chin-Ting Kuo <chin-ting_kuo@aspeedtech.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
User can get correct HCLK frequency during driver probe stage
by adding the following configuration in the device tree.
"clocks = <&scu ASPEED_CLK_AHB>".
Signed-off-by: Chin-Ting Kuo <chin-ting_kuo@aspeedtech.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
As the flash sizes are increasing day by day, QSPI can have devices of
size > 512MB. In qspi driver we are trying to read all the data at once
using DMA.
The DMA descriptor destination size is only 29bits long.
QSPIDMA_DST_SIZE 0xFF0F0804
BITS: 1:0 Reserved to keep word alignment
BITS: 28:2 Number of 4-byte words the DMA will transfer
BITS: 31:29 Reserved: Returns 0 when read, writes ignored
So we can only transfer data of 0x1FFFFFF0(512MB minus 4bytes) bytes.
Anything above will overflow this register and will ignore higher bits
above 29 bits.
Change the DMA functionality if the requested size is greater than or
equal to 512MB to read 256MB chunks.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@amd.com>
Link: https://lore.kernel.org/r/20220825125906.11581-5-ashok.reddy.soma@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
In cadence_spi_probe, cadence_qspi_versal_flash_reset() is called to reset
the flash device. Looks like there is a mistake in previous series of
patches where it is defined as cadence_spi_versal_flash_reset() but
called as cadence_qspi_versal_flash_reset. Since there is a weak function
defined with the same name this issue was not caught.
Fix the issue by renaming cadence_spi_versal_flash_reset as
cadence_qspi_versal_flash_reset().
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Link: https://lore.kernel.org/r/20220824113847.7482-2-ashok.reddy.soma@xilinx.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Check snprintf() return value for errors.
Make microblaze_cpu_get_desc() directly return snprintf() error code if
ret < 0. Otherwise, if the return value is greater than or equal to size,
the resulting string is truncated, so return -ENOSPC.
Fixes: 816226d27e ("cpu: add CPU driver for microblaze")
Signed-off-by: Ovidiu Panait <ovpanait@gmail.com>
Link: https://lore.kernel.org/r/20220829170205.1274484-2-ovpanait@gmail.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
- simplify the STM32MP15x package parsing code
- remove test on CONFIG_DM_REGULATOR in stm32mp1 board
and enable CONFIG_DM_REGULATOR for stm32f769-disco
- handle ck_usbo_48m clock provided by USBPHYC to fix the command 'usb start'
after alignment with Linux kernel v5.19 DT (clocks = <&usbphyc>)
- Fix SYS_HZ_CLOCK value for stih410-b2260 board
- Switch STMM32MP15x DHSOM to FMC2 EBI driver
- Remove hwlocks from pinctrl in STM32MP15x to avoid issue with kernel
Fman microcode is executable code (AFAICT) loaded into a
coprocessor. As such, if verified boot is enabled, it must be verified
like other executable code. However, this is not currently done.
This commit adds verified boot functionality by encapsulating the
microcode in a FIT, which can then be signed/verified as normal. By
default we allow fallback to unencapsulated firmware, but if
CONFIG_FIT_SIGNATURE is enabled, then we make it mandatory. Because
existing Layerscape do not use this config (instead enabling
CONFIG_CHAIN_OF_TRUST), this should not break any existing boards.
An example (mildly-abbreviated) its is provided below:
/ {
#address-cells = <1>;
images {
firmware {
data = /incbin/(/path/to/firmware);
type = "firmware";
arch = "arm64";
compression = "none";
signature {
algo = "sha256,rsa2048";
key-name-hint = "your key name";
};
};
};
configurations {
default = "conf";
conf {
description = "Load FMAN microcode";
fman = "firmware";
};
};
};
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Several ethernet drivers load firmware from FIT images. Convert them to
use the fit_get_data helpers.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
ck_usbo_48m is generated by usbphyc PLL and used by OTG controller
for Full-Speed use cases with dedicated Full-Speed transceiver.
ck_usbo_48m is available as soon as the PLL is enabled.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Add the counter of the PLL user n_pll_cons managed by the 2 functions
stm32_usbphyc_pll_enable / stm32_usbphyc_pll_disable.
This counter allow to remove the function stm32_usbphyc_is_init
and it is a preliminary step for ck_usbo_48m introduction.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
System reset via the SRST extension in the SBI should be the default.
The driver checks if the extension is available when probing.
So there is no risk in enabling it.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
This commit sychronizes the header file for FU740 PRCI clocks with the
one from Linux 5.19.
The constant values are the same, but all constant names are changed
(most are just prefixed with FU740_).
Signed-off-by: Icenowy Zheng <uwu@icenowy.me>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
If ethernet connected to SFP, like this:
&enetc_port0 {
phy-connection-type = "sgmii";
sfp = <&sfp0>;
managed = "in-band-status";
status = "okay";
};
Then enetc_config_phy returns -ENODEV and the memory containing the mdio interface is freed.
It's better to unregister and free mdio resources.
Signed-off-by: Siarhei Yasinski <siarhei.yasinski@sintecs.eu>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
