Currently, we have the function env_get_ip which takes an IP address
in string form and returns a struct in_addr representation of that
address. It is however little used and means that a number of places
indirectly (and unclearly) get <env.h> via <net.h>. To clean this up
start by replacing env_get_ip() calls with string_to_ip() calls. This is
generally a no-op as env_get_ip(str) is an inline of
string_to_ip(env_get(str)) but in a few cases we can or already have
stored the result of env_get(str) and can save the additional call.
Signed-off-by: Tom Rini <trini@konsulko.com>
The commit ac30d90f33 ("clk: Ensure the parent clocks are enabled
while reparenting") add a call to clk_enable() for the parent clock.
For clock drivers that do not implement the enable() ops, like most
Rockchip clock drivers, this now cause the set_parent() ops to never
be called when CLK_CCF=n (default for Rockchip).
clk_enable() typically return -ENOSYS when the enable() ops is not
implemented by the clock driver, with CLK_CCF=y clk_enable() instead
return 0 when the enable() ops is unimplemented.
Change to ignore -ENOSYS from the newly introduced clk_enable() call to
fix this regression and restore the old behavior of set_parent() ops
being called regardless of if enable() ops is implemented or not.
Fixes: ac30d90f33 ("clk: Ensure the parent clocks are enabled while reparenting")
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Tested-by: Dang Huynh <danct12@riseup.net>
Acked-by: Miquel Raynal <miquel.raynal@bootlin.com>
Currently, Synopsis xgmac driver only works if DMA region is under 4GB.
This change enables the DMA buffers allocations above 4GB memory
regions.
Signed-off-by: Nikunj Kela <nikunj.kela@sima.ai>
This file was using IS_ENABLED() to test for CONFIG flags but omitted
the CONFIG_ prefix and so did not work as expected.
Signed-off-by: Tom Rini <trini@konsulko.com>
Add support for Skyworks AAT2870 LED Backlight Driver and Multiple LDO
Lighting Management Unit. Only backlight is supported as for now. Supported
backlight level range is from 2 to 255 with step of 1.
Tested-by: Ion Agorria <ion@agorria.com>
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
LG LH400WV3-SD04 is a color active matrix TFT (Thin Film Transistor)
liquid crystal display (LCD). The resolution of a 4" contains 480 x 800
pixels.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Hitachi TX10D07VM0BAA is a color active matrix TFT (Thin Film Transistor)
liquid crystal display (LCD). The resolution of a 4" contains 480 x 800
pixels.
Tested-by: Ion Agorria <ion@agorria.com>
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Add support for 8-bit CPU driven (primary and secondary) display signal
interface found in Tegra 2 and Tegra 3 SoC.
Tested-by: Ion Agorria <ion@agorria.com>
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
MAX8907 PMIC has embedded poweroff function used by some device to initiane
device power off. Implement it as optional sysreset driver guarded by
kconfig option and system-power-controller device tree property.
Tested-by: Ion Agorria <ion@agorria.com>
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Added a new regulator driver for the MAXIM MAX8907 PMIC, providing
essential regulator functionalities and incorporated the necessary binding
framework within the core PMIC driver.
Tested-by: Ion Agorria <ion@agorria.com>
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Releasing a GPIO on Tegra necessitates changing its configuration to SFIO
to activate its special function. Without this reconfiguration, the special
function will be unavailable.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Add RMII-specific handling to rk3288_gmac_fix_mac_speed() so that it
properly sets the RMII clock (2.5 MHz vs. 25 MHz) and speed bits
(10 Mbps vs. 100 Mbps). Also define a new rk3288_gmac_set_to_rmii()
function to set the PHY interface field and RMII_MODE bit.
Signed-off-by: Christoph Fritz <chf.fritz@googlemail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Write enable(06h) command will be sent to a flash device to
set the write enable latch bit before every program, erase,
write command. After that write disable command (04h) needs
to be sent to clear the write enable latch.
This write_disable() is missing at the majority of the places
in the driver, add it to clear write enable latch.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
Link: https://gist.github.com/PrasanthBabuMantena/c12f39744de188a9d08cd5ca51dc2a7b
Tested-by: Prasanth Babu Mantena <p-mantena@ti.com>
MT35XU512ABA has only BFPT and 4-Byte Address Instruction Table
in SFDP. commit bebdc23750 ("mtd: spi-nor: Parse SFDP SCCR Map")
added checks in spi_nor_octal_dtr_enable() to bail out if the 22nd DWORD
in SCCR does not indicate DTR Octal Mode Enable, since MT35XU512ABA device
supports octal DTR mode, add this property in SFDP fixup.
Signed-off-by: Vaishnav Achath <vaishnav.a@ti.com>
Signed-off-by: Prasanth Babu Mantena <p-mantena@ti.com>
Reviewed-by: Udit Kumar <u-kumar1@ti.com>
The IO domain driver controls the I/O voltage for various pins,
MMC included.
Enable it by default for all supported Rockchip SoCs.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Quentin Schulz <quentin.schulz@cherry.de>
Reviewed-by: Paul Kocialkowski <paulk@sys-base.io>
Reviewed-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Anand Moon <linux.amoon@gmail.com>
There's no need to modify private data from the controller, so let's
make that struct const.
Signed-off-by: Quentin Schulz <quentin.schulz@cherry.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
There's no need to modify private data from the controller, so let's
make that struct const.
Signed-off-by: Quentin Schulz <quentin.schulz@cherry.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
There's no need to modify private data from the controller, so let's
make that struct const.
Signed-off-by: Quentin Schulz <quentin.schulz@cherry.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
There's no need to modify private data from the controller, so let's
make that struct const.
Signed-off-by: Quentin Schulz <quentin.schulz@cherry.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
There's no need to modify private data from the controller, so let's
make that struct const.
Signed-off-by: Quentin Schulz <quentin.schulz@cherry.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
There's no need to modify private data from the controller, so let's
make that struct const.
Signed-off-by: Quentin Schulz <quentin.schulz@cherry.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
There's no need to modify private data from the controller, so let's
make that struct const.
Signed-off-by: Quentin Schulz <quentin.schulz@cherry.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
There's no need to modify private data from the controller, so let's
make that struct const.
Signed-off-by: Quentin Schulz <quentin.schulz@cherry.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
There's no need to modify private data from the controller, so let's
make that struct const.
Signed-off-by: Quentin Schulz <quentin.schulz@cherry.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
There's no need to modify private data from the controller, so let's
make that struct const.
Signed-off-by: Quentin Schulz <quentin.schulz@cherry.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
There's no need to modify private data from the controller, so let's
make that struct const.
Signed-off-by: Quentin Schulz <quentin.schulz@cherry.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
There's no need to modify private data from the controller, so let's
make that struct const.
Signed-off-by: Quentin Schulz <quentin.schulz@cherry.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The logic in the core reads the nr_pins of the controller and uses it as
the index of the first pin in the bank (pin_base) it currently parses.
It then increments the number of pins in the controller before going to
the next bank.
This works "fine" for controllers where nr_pins isn't defined in their
rockchip_pin_ctrl struct as it defaults to 0. However, when it is
already set, it'll make the index pin of each bank offset by the number
in nr_pins declared in the struct at initialization, and it'll keep
growing while adding banks, which means the total number of pins in the
controller will be misrepresented.
Additionally, U-Boot proper may probe this driver twice (pre-reloc and
true proper) and not reset nr_pins of the controller in-between meaning
the second probe will have an offset of the actual correct nr_pins.
Instead, let's just store locally the number of pins in the controller
and make sure it's reset between probes.
Finally, this stops modifying a const struct which will soon be
triggering a CPU abort at runtime.
Signed-off-by: Quentin Schulz <quentin.schulz@cherry.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
On K3 devices two drivers ti_sci and ti_sci_dm are supporting firmware
functions. At run time one of driver is used.
Driver ti_sci already initializing head for dev_list in its probe
function, but it was missed in ti_sci_dm driver.
So add head list init support for ti_sci_dm driver.
While at this, move init of list before usages in both functions.
Fixes: 5d5a699855a7("firmware: ti_sci: Add support for Resoure Management at R5 SPL stage")
Reviewed-by: Neha Malcom Francis <n-francis@ti.com>
Signed-off-by: Udit Kumar <u-kumar1@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
- CI: https://source.denx.de/u-boot/custodians/u-boot-stm/-/pipelines/26081
- STM32 MCUs:
- Fix console cmdline
- Add support NT35510 panel controller on stm32f769i-disco board
- Fix dfu alt buffer clearing
- Enable scan and start for AB schema on STM32MP15 DHSOM
- Add stm32mp2 support for dwc_eth_qos
[backport from Linux commits 9b26d5c044d6a29ebfb1845408e0f2a7c5f89818
and 219a1f49094f50bf9c382830d06149e677f76bed]
The patch adds the FRIDA FRD400B25025-A-CTK panel, which belongs to the
Novatek NT35510-based panel family.
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
The MTD device reference is dropped via put_mtd_device, however its
field ->index is read and passed to ubi_msg. To fix this, the patch
moves the reference dropping after calling ubi_msg.
Signed-off-by: Pan Bian <bianpan2016@163.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
Upstream Linux commit: b95f83ab762dd6211351b9140f99f43644076ca8
Signed-off-by: Alexander Vickberg <wickbergster@gmail.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
The Renesas R9A07G044L (RZ/G2L) SoC includes two Gigabit Ethernet
interfaces which can be supported using the ravb driver. Some RZ/G2L
specific steps need to be taken during initialization due to differences
between this SoC and previously supported SoCs. We also need to ensure
that the module reset is de-asserted after the module clock is enabled
but before any Ethernet register reads/writes take place.
Signed-off-by: Paul Barker <paul.barker.ct@bp.renesas.com>
In order to add support for the Renesas RZ/G2L Ethernet IP in a
subsequent patch, we introduce optional de-assertion and re-assertion of
a reset signal in ravb_probe() and ravb_remove().
Signed-off-by: Paul Barker <paul.barker.ct@bp.renesas.com>
In order to add support for the Renesas RZ/G2L Ethernet IP in a
subsequent patch, we move all R-Car specific code into new functions and
introduce a device_ops function pointer table.
Signed-off-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Correctly handle RX errors in ravb_recv() by returning 0 instead
of -EAGAIN on RX error.
In case the RAVB driver detects an RX error in ravb_recv(), it must
not return the -EAGAIN, but instead must return 0. Both error codes
are handled in eth-uclass.c eth_rx() and -EAGAIN is rewritten to 0
at the end of eth_rx(), but negative return code from the .recv()
callback does not trigger .free_pkt() callback, which would clean
up and re-enqueue the descriptor which holds the currently received
corrupted packet. The .free_pkt() must be called for this descriptor,
otherwise the follow up received data become corrupted too, even if
those packets are correctly received. Returning 0 from the .recv()
callback assures the corrupted packet is not processed by the network
stack, but is skipped instead.
For TFTP loading, an RX error produces the timeout "T" output and
resumes the TFTP loading operation shortly afterward, without any
data corruption.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Paul Barker <paul.barker.ct@bp.renesas.com>
@protocols is an array of protocol identifiers that are implemented,
excluding the Base protocol. Four protocol identifiers are packed into
each array element. The number of elements of @protocols is specified by
callee-side.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Alice Guo <alice.guo@nxp.com>
Clock driver based on SCMI clock management protocol in Linux checks
clock state, parent and rate control permissions. To be consistent with
the kernel driver, add this check here. CLOCK_GET_PERMISSIONS is from
ARM System Control and Management Interface Platform Design Document 3.2.
When using common clock framework (CCF), use the clock signal ID to get
the clock registered by clk_register() in scmi_clk_probe(), and then
obatin the struct clk_scmi variable with container_of().
Signed-off-by: Alice Guo <alice.guo@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
This patch adds the command CLOCK_PARENT_SET that can be used to set the
parent of a clock. ARM SCMI Version 3.2 supports to change the parent of
a clock device.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Alice Guo <alice.guo@nxp.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Marek Vasut <marex@denx.de>
This patch adds SCMI pin control protocol support to make the pin
controller driver based on SCMI, such as
drivers/pinctrl/nxp/pinctrl-imx-scmi.c, can be bound to the SCMI agent
device whose protocol id is 0x19.
Signed-off-by: Alice Guo <alice.guo@nxp.com>
