SPL_TEXT_BASE is used as the load address for the main domain SPL on k3
platforms.
Since the config value is the same for every board, this patch sets the
value 0x80080000 as default for all 64-bit ARCH_K3, 0x43c00000 as
default for the R5 cores and deletes the instances of SPL_TEXT_BASE in
individual defconfigs.
Signed-off-by: Anshul Dalal <anshuld@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Enable support for USB DFU boot via USB0 instance of USB on J784S4 SoC
which is a Cadence USB Controller. Additionally, enable support for USB
DFU flash and USB Mass Storage (UMS) command. While at it, sync with
savedefconfig.
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Judith Mendez <jm@ti.com> says:
Some K3 devices like am62x and am64x have a M4 processor in the MCU
voltage domain. This patch series introduces remoteproc M4 driver which
will be used to load firmware into and start the M4 remote core.
This series also adds support for R5F cores on am64x SoCs in patch 2 and
sets up environment to load FW in remote cores in patch 3,4,5.
This patch series also enables remoteproc drivers by default as per what
remoteproc sybsystem is supported per SoC, thus all remoteproc options
are now deleted in configs/* since they are no longer required.
This patch series was tested on am64x EVM, am62x SK, am62ax SK,
am62px SK boards.
Any additional tested by's are welcome since I was not able to
test any additional boards.
Tested by running the following commands in u-boot prompt:
=> setenv dorprocboot 1
=> run boot_rprocs
Link: https://lore.kernel.org/r/20250210202944.1071931-1-jm@ti.com
Now that remoteproc configs are enabled by default in Kconfig
files, remove these configs which are no longer needed to be
defined here in configs/.
Signed-off-by: Judith Mendez <jm@ti.com>
Reviewed-by: Andrew Davis <afd@ti.com>
Set CONFIG_NR_DRAM_BANKS to 2 as we have two banks described in the
memory/ node for lower and higher addressible DDR regions.
This allows use of FDT functions from fdt_support.c to set up and fix up
the memory/ node correctly.
Signed-off-by: Neha Malcom Francis <n-francis@ti.com>
Signed-off-by: Santhosh Kumar K <s-k6@ti.com>
Instead of bloating the defconfig with CONFIG_CMD_*, move J7 devices to
start using TI_COMMON_CMD_OPTIONS.
Signed-off-by: Neha Malcom Francis <n-francis@ti.com>
Make the raw-mode options depend on SPL_SYS_MMCSD_RAW_MODE in a more
direct way. This makes it easier to understand the options with
'make menuconfig'.
There are three different ways of specifying the offset:
- sector offset
- partition number
- partition type
So make these a choice, so it is more obvious what is going on.
Update existing boards to enable SPL_SYS_MMCSD_RAW_MODE where needed.
Reviewed-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Quentin Schulz <quentin.schulz@cherry.de>
Signed-off-by: Simon Glass <sjg@chromium.org>
The K3 J784S4 SoC has four dual-core R5F subsystems and four C71x DSP
subsystems. Set config values to enable the remoteproc functionality
with these R5F and DSP subsystems.
Signed-off-by: Beleswar Padhi <b-padhi@ti.com>
