Add TI_COMMON_CMD_OPTIONS config options to Sitara K3 boards at
a53 stage since we rely on most of the commands implied for testing
and debugging purposes. Since all commands are now enabled by
default, remove the redundant CMD_* options in the a53 defconfigs.
Also add MMC_REG & MMC_SPEED_MODE_SET useful commands to
TI_COMMON_CMD_OPTIONS.
Signed-off-by: Judith Mendez <jm@ti.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
SPL_TEXT_BASE is used as the load address for the main domain SPL on k3
platforms.
Since the config value is the same for every board, this patch sets the
value 0x80080000 as default for all 64-bit ARCH_K3, 0x43c00000 as
default for the R5 cores and deletes the instances of SPL_TEXT_BASE in
individual defconfigs.
Signed-off-by: Anshul Dalal <anshuld@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Judith Mendez <jm@ti.com> says:
Some K3 devices like am62x and am64x have a M4 processor in the MCU
voltage domain. This patch series introduces remoteproc M4 driver which
will be used to load firmware into and start the M4 remote core.
This series also adds support for R5F cores on am64x SoCs in patch 2 and
sets up environment to load FW in remote cores in patch 3,4,5.
This patch series also enables remoteproc drivers by default as per what
remoteproc sybsystem is supported per SoC, thus all remoteproc options
are now deleted in configs/* since they are no longer required.
This patch series was tested on am64x EVM, am62x SK, am62ax SK,
am62px SK boards.
Any additional tested by's are welcome since I was not able to
test any additional boards.
Tested by running the following commands in u-boot prompt:
=> setenv dorprocboot 1
=> run boot_rprocs
Link: https://lore.kernel.org/r/20250210202944.1071931-1-jm@ti.com
Now that remoteproc configs are enabled by default in Kconfig
files, remove these configs which are no longer needed to be
defined here in configs/.
Signed-off-by: Judith Mendez <jm@ti.com>
Reviewed-by: Andrew Davis <afd@ti.com>
AM62x BOOTM_LEN is too small to contain OS images. Removing this sets the
size to a default 0x4000000 (for all arm64 devices).
It is unnecessary to specifically call the default size for the other
configs.
Signed-off-by: Kamlesh Gurudasani <kamlesh@ti.com>
Signed-off-by: Aashvij Shenai <a-shenai@ti.com>
Set CONFIG_NR_DRAM_BANKS to 2 as we have two banks described in the
memory/ node for lower and higher addressible DDR regions.
This allows use of FDT functions from fdt_support.c to set up and fix up
the memory/ node correctly.
Signed-off-by: Neha Malcom Francis <n-francis@ti.com>
Signed-off-by: Santhosh Kumar K <s-k6@ti.com>
Make the raw-mode options depend on SPL_SYS_MMCSD_RAW_MODE in a more
direct way. This makes it easier to understand the options with
'make menuconfig'.
There are three different ways of specifying the offset:
- sector offset
- partition number
- partition type
So make these a choice, so it is more obvious what is going on.
Update existing boards to enable SPL_SYS_MMCSD_RAW_MODE where needed.
Reviewed-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Quentin Schulz <quentin.schulz@cherry.de>
Signed-off-by: Simon Glass <sjg@chromium.org>
Enable OF_UPSTREAM for am625-sk board. Remove DT files that
are now available in dts/upstream. Update the appended files based on
version of latest OF_UPSTREAM sync point (v6.10-rc1).
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Tested-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
Reviewed-by: Dhruva Gole <d-gole@ti.com>
Provide config fragments to enable USB host as well as USB gadget and DFU
support for a53 and r5. This relevant fragment is included into the
am62x EVM a53 defconfig. For the r5, due to the smaller available size,
the config fragment also disables support for persistent storage to free
up space for USB support. This fragment needs to be included is DFU
booting is desired.
The CONFIG_DFU_SF option is placed in the defconfig rather than the
fragment as this is known not to be supported on all boards that can
support DFU.
Signed-off-by: Sjoerd Simons <sjoerd@collabora.com>
Signed-off-by: Martyn Welch <martyn.welch@collabora.com>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Jonathan Humphreys <j-humphreys@ti.com> says:
Set basic settings needed for System Ready IR ACS testing, for several TI SoC
based platforms: AM64, AM62, AM62p, BeaglePlay, J7, and BeagleboneAI.
For AM64, AM62, and AM62p, also includes some config cleanup. Should be no
functional change.
With the current config for tha SK-AM62, fdtfile isn't set in the U-Boot
environment. When using bootflow to boot from a block device, where the
extlinux.conf file specifies `fdtdir`, a fallback device tree is being
constructed from the `soc` (`k3`) and `board` (`am62x`) environment
variables, resulting in u-Boot trying to retrieve
`/dtbs/6.8.1+/k3-am62x.dtb`. This file doesn't exist.
The environment variables `default_device_tree` and
`default_device_tree_arch` are set in the config, the `findfdt` script
can be called to construct `fdtfile` from the environment variables set
by these config options, however this script currently isn't being run.
Calling this script results in the correct device tree being retrieved:
Retrieving file: /dtbs/6.8.1+/ti/k3-am625-sk.dtb
Many boards are calling this script as part of their boot command. The
am62x currently isn't. Rectify this so that booting works correctly.
Signed-off-by: Martyn Welch <martyn.welch@collabora.com>
Reviewed-by: Christopher Obbard <chris.obbard@collabora.com>
There is a default ATF load address that is used for devices that have
ATF running in SRAM. For AM62 and AM62a, ATF runs from DRAM. Instead
of having to override the address in every defconfig, make add a
default for these ATF in DRAM devices.
Signed-off-by: Andrew Davis <afd@ti.com>
Acked-by: Bryan Brattlof <bb@ti.com>
Reviewed-by: Neha Malcom Francis <n-francis@ti.com>
Stop using the findfdt script and switch to setting the fdtfile from
C code.
While at this, replace findfdt in environment with a warning as it is
no longer needed
Reviewed-by: Jonathan Humphreys <j-humphreys@ti.com>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Signed-off-by: Nishanth Menon <nm@ti.com>
The help for CONFIG_MTD explains that it needs to be enabled for various
things like NAND, etc to be available. It however then doesn't enforce
this dependency and so if you have none of these systems present you
still need to disable a number of options. Fix this by making places
that select/imply one type of flash, but did not do the same, also do
this for "MTD". Make boards which hadn't been enabling MTD already but
need it now, do so. In a few places, disable CONFIG_CMD_MTDPARTS as it
wasn't previously enabled but was now being implied.
Signed-off-by: Tom Rini <trini@konsulko.com>
All K3 boards now are secure by default, instead of setting this in each
defconfig, make it implied by the ARCH config.
The only exception is IOT2050, which I do not believe will have any
problems with being a TI_SECURE_DEVICE, but for now turn it off to keep
its config the same.
Signed-off-by: Andrew Davis <afd@ti.com>
Tested-by: Tom Rini <trini@konsulko.com>
This was regressed by the following commit and is required to build with
additional configs enabled.
Fixes: 14439cd71c ("configs: k3: make consistent bootcmd across all k3 socs")
Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
Tested-by: Nikhil M Jain <n-jain1@ti.com>
Default to common bootcmd that is set across all k3 devices.
Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
Signed-off-by: Kamlesh Gurudasani <kamlesh@ti.com>
Enable the CONFIG_TI_SECURE_DEVICE by default
Non-HS devices will continue to boot due to runtime device type detection.
TI's security enforcing SoCs will authenticate each binary it loads by
comparing it's signature with keys etched into the SoC during the boot
up process. The am62x family of SoCs by default will have some level of
security enforcement checking. To keep things as simple as possible,
enable the CONFIG_TI_SECURE_DEVICE options by default so all levels of
secure SoCs will work out of the box
Signed-off-by: Praneeth Bajjuri <praneeth@ti.com>
Signed-off-by: Kamlesh Gurudasani <kamlesh@ti.com>
Signed-off-by: Bryan Brattlof <bb@ti.com>
Setting sf default mode to 0x3 breaks sf update when we do SF read
through u-boot console.
This issue arises when we do a splash image through OSPI flash media,
to fix this set the default mode to 0x0.
Fixes: 04150400c9 ("configs: enable OSPI related configs in AM62x")
Signed-off-by: Nikhil M Jain <n-jain1@ti.com>
TI boards use a custom (though faily common to TI boards) mechanism for
booting Linux. We would like to use the "distroboot" approach.
Enable distroboot as a further option to use for booting on am625 should
the existing options fail.
Signed-off-by: Martyn Welch <martyn.welch@collabora.com>
In f422c4bec the configuration option to support s28hs512t SPI flashes
was changed from CONFIG_SPI_FLASH_S28HS512T to CONFIG_SPI_FLASH_S28HX_T
to support the wider family. Follow this change in the AM62x EVM
configurations.
Signed-off-by: Sjoerd Simons <sjoerd@collabora.com>
Reviewed-by: Dhruva Gole <d-gole@ti.com>
Add am62x_evm_r5_defconfig for OSPI Flash support in R5 SPL
and am62x_evm_a53_defconfig for A53 SPL and U-Boot
support.
These configs enable OSPI Flash boot functionality in the board as well
as the usage of OSPI Flash from U-Boot.
Signed-off-by: Dhruva Gole <d-gole@ti.com>
