The BootROM in Rockchip SoCs will enter maskrom mode when boot firmware
cannot be found in nand/spi/mmc storage.
In maskrom mode the USB OTG port can accept one of two custom commands.
Initially a 0x471 command to load TPL into SRAM. After TPL has been
executed and it has returned back-to-BROM, a 0x472 command to load SPL
into start of DRAM.
Add two binman images that can be used to RAM boot from maskrom mode:
- u-boot-rockchip-usb471.bin that contains TPL to init DRAM.
- u-boot-rockchip-usb472.bin that contains SPL and the normal FIT
payload with i.e. U-Boot proper, TF-A and FDT.
A config fragment rockchip-ramboot.config can be used to enable building
of these two binman images, e.g.:
make generic-rk3588_defconfig rockchip-ramboot.config
These binman images can be used with the proprietary rkbin boot_merger
tool to create a special loader image that can be used with tools such
as rkdeveloptool or rockusb tools to RAM boot from maskrom, e.g.:
Create loader image:
$ ../rkbin/tools/boot_merger ./RK3588MINIALL.ini
Boot from maskrom:
$ rkdeveloptool db u-boot-rockchip-rk3588-loader.bin
or
$ rockusb download-boot u-boot-rockchip-rk3588-loader.bin
Another option that does not require use of proprietary tools is using
open source tools such as rkflashtool or rkusbboot that can load the
binman images directly without any need to first create a special loader
image to RAM boot from maskrom, e.g.:
$ rkflashtool l < u-boot-rockchip-usb471.bin
$ rkflashtool L < u-boot-rockchip-usb472.bin
or
$ rkusbboot u-boot-rockchip-usb471.bin u-boot-rockchip-usb472.bin
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Tested-by: Arnaud Patard <arnaud.patard@collabora.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
SPL_FIT_FULL_CHECK currently shares its description and help text with
FIT_FULL_CHECK which is quite confusing, so let's specify this applies
to SPL.
Fixes: 6f3c2d8aa5 ("image: Add an option to do a full check of the FIT")
Signed-off-by: Quentin Schulz <quentin.schulz@cherry.de>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@kernel.org>
Anshul Dalal <anshuld@ti.com> says:
Hi all,
We currently make use of CMD_BOOTI and CMD_BOOTZ in the SPL boot flow in
falcon mode, this isn't correct since all CMD_* configs are only meant
for U-Boot proper and not the SPL.
Therefore this patch set adds new LIB_BOOT[IMZ] configs that allow for
more granular selection of their respective compilation targets.
Additionally, this also allows us to more easily disable support for
raw images from secure falcon mode (SPL_OS_BOOT_SECURE) by doing the
following:
config LIB_SPL_BOOTI
...
depends on SPL_OS_BOOT && !SPL_OS_BOOT_SECURE
...
Link: https://lore.kernel.org/r/20251027-fix_cmd_bootx-v10-0-10487e907710@ti.com
Using CMD_* configs from spl doesn't make logical sense. Therefore
this patch replaces the checks for CMD_BOOTx with newly added library
symbols LIB_BOOT[IMZ] and SPL_LIB_BOOT[IMZ] which are enabled by their
respective CMD_* or SPL_* counterparts.
On platforms with non-secure falcon mode, SPL_BOOTZ is enabled by
default for 32-bit ARM systems and SPL_BOOTI is enabled by default for
64-bit ARM and RISCV.
The respective C files (image.c/zimage.c) are compiled based on library
symbols $(PHASE_)LIB_BOOTx instead which are in turn selected by both
CMD_BOOTx and SPL_BOOTx as required.
Signed-off-by: Anshul Dalal <anshuld@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Kory Maincent (TI.com) <kory.maincent@bootlin.com> says:
This series converts the extension board framework to use UCLASS as
requested by Simon Glass, then adds extension support to pxe_utils
and bootmeth_efi (not tested) to enable extension boards devicetree load
in the standard boot process.
I can't test the imx8 extension scan enabled by the
imx8mm-cl-iot-gate_defconfig as I don't have this board.
I also can't test the efi bootmeth change as I don't have such board.
Link: https://lore.kernel.org/r/20251030-feature_sysboot_extension_board-v5-0-cfb77672fc68@bootlin.com
Remove the legacy extension board implementation now that all boards
have been converted to use the new UCLASS-based framework. This
eliminates lines of legacy code while preserving functionality
through the modern driver model approach.
Update the bootstd tests, due to the removal of extension hunter.
Signed-off-by: Kory Maincent (TI.com) <kory.maincent@bootlin.com>
Introduce UCLASS-based extension board support to enable more
standardized and automatic loading of extension board device tree
overlays in preparation for integration with bootstd and pxe_utils.
Several #if CONFIG_IS_ENABLED are used in cmd/extension_board.c to ease the
development but don't worry they are removed later in the series.
Signed-off-by: Kory Maincent (TI.com) <kory.maincent@bootlin.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Relocate extension board support from cmd/ to boot/ directory in
preparation for converting the extension framework to use UCLASS.
Also improve code style by applying reverse xmas tree ordering.
Signed-off-by: Kory Maincent (TI.com) <kory.maincent@bootlin.com>
Today, only a few platforms enable SPL_LOAD_FIT_FULL, and all enable
SPL_LOAD_FIT. As can be seen in usage, the FULL symbol is a superset of
the first symbol, not an alternative. Update Kconfig entries based on
this and simplify the only code which checks for either being set.
Signed-off-by: Tom Rini <trini@konsulko.com>
Only PowerPC and LS1021A platforms can make use of RAMBOOT_PBL. Add the
dependencies to the symbol.
Signed-off-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
We have a large number of library symbols that should not be prompted
for by the user really but rather selected by the platform (or SoC) as
needed. To start with however, make these depend on !COMPILE_TEST.
Signed-off-by: Tom Rini <trini@konsulko.com>
The ARM64 kernel Image size with LOCKDEP enabled is now around 80 MiB, which
makes it unbootable due to "Image too large: increase CONFIG_SYS_BOOTM_LEN".
Increase the image size limit to 128 MiB to future proof the limit.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
At this time there are still major Linux distributions which by default
boot using LEGACY_IMAGE_FORMAT type scripts. Add this option to
DISTRO_DEFAULTS to ensure these platforms can still boot.
Fixes: d780965927 ("Drop the special am335x_boneblack_vboot target")
Reported-by: Sascha Silbe <sascha-pgp@silbe.org>
Tested-By: Sascha Silbe <sascha-pgp@silbe.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
Since the bootmeth "rauc" is not a global boot method, do not select the
corresponding BOOTMETH_GLOBAL option.
Signed-off-by: Martin Schwan <m.schwan@phytec.de>
João Paulo Gonçalves <jpaulo.silvagoncalves@gmail.com> says:
In some use cases, board-specific device tree changes must not be overwritten
by system fixups. Although U-Boot provides ft_board_setup_ex() for this
purpose, it is currently only used on TI Keystone. This series makes
ft_board_setup_ex() a generic option, allowing its use by other architectures
and boards.
Additionally, considering that Toradex Verdin-AM62P hardware lifetime
guarantees are based on a 105°C junction temperature (while TI AM62Px supports
up to 125°C), this series implements necessary changes within TI K3 AM62P and
Toradex board code. These changes include exporting common fixup device Tree
functions used in TI K3 for board-code access and also fixup for AM62P thermal
zones to correctly reflect the number of CPU nodes according to the SoC part
number.
Link: https://lore.kernel.org/r/20250623-am62p-fdt-fixup-trip-points-v1-0-12355eb6a72f@toradex.com
In some use cases, board-specific device tree changes must not be
overwritten by system fixups. Although U-Boot provides
ft_board_setup_ex() for this purpose, it is currently only used on TI
Keystone. Make ft_board_setup_ex() to be a generic option, allowing its
use by other architectures/boards. To maintain backward compatibility,
enable it by default on TI Keystone.
Signed-off-by: João Paulo Gonçalves <joao.goncalves@toradex.com>
Rename the variable and add ENV_ prefix, so that all configuration
options which are related to environment would have an CONFIG_ENV_
prefix. No functional change.
Also rename USE_DEFAULT_ENV_FILE to USE_ENV_DEFAULT_ENV_TEXT_FILE .
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Martin Schwan <m.schwan@phytec.de> says:
This series implements a new bootmeth for RAUC A/B systems. RAUC (Robust
Auto Update Controller) is a lightweight update client, providing "Safe
and Secure OTA Updates for Embedded Linux". See the following links for
more information about RAUC:
https://rauc.io/https://rauc.readthedocs.io/en/latest/
PHYTEC uses RAUC in its Yocto based distribution "Ampliphy" as the
default way of updating embedded devices based on PHYTEC hardware. So
far, the logic selecting the correct partitions and files to boot was
being implemented in the U-Boot environment. While this is a
straightforward way to do it, adding and supporting new platforms became
somewhat tedious and is platform-specific. The introduction of U-Boot's
"Standard Boot" provided a convincing alternative, promising a simpler
and more portable way of booting, even for RAUC systems. This led me to
implement a new bootmeth supporting RAUC A/B systems. Note, that this
new bootmeth is not proprietary to PHYTEC products and is designed to
work on other hardware with a RAUC A/B system, too.
The bootmeth currently only supports symmetric A/B partitioning layouts.
E.g. A/rescue is not (yet) supported. The partition indexes and default
slot tries can be specified via configuration options.
For now, the bootmeth_rauc uses a similar approach for loading the
Kernel and device tree as the bootmeth_script, in that it requires a FIT
containing a U-Boot script loading the desired distro. It could be
possible to support booting without a script and load the Kernel and DT
directly with this bootmeth, but I found the script method to be very
flexible for now, in letting the distro decide what to load.
The bootmeth_rauc was tested on a phyBOARD-Pollux i.MX8M Plus [1] with
BSP-Yocto-Ampliphy-i.MX8MP-PD24.1.2 [2].
Supported boot devices are currently only MMC devices, but it should be
possible to add SPI flashes in the future.
To test this patch stack with PHYTEC's phyBOARD-Pollux i.MX8M Plus
board, you need to adjust the boot files to include the boot.scr.uimg
containing the distro's boot script and set "optargs" to "${raucargs}"
in it. Also disable any legacyboot in the U-Boot environment and simply
boot with Standard Boot:
bootmeth order rauc
bootflow scan -lb
[1]: https://www.phytec.eu/en/produkte/single-board-computer/phyboard-pollux/
[2]: https://download.phytec.de/Software/Linux/BSP-Yocto-i.MX8MP/BSP-Yocto-Ampliphy-i.MX8MP-PD24.1.2/
Link: https://lore.kernel.org/r/20250604-wip-bootmeth-rauc-v3-0-f9fad913c57e@phytec.de
[trini: Don't enable by default]
Add a bootmeth driver which supports booting A/B system with RAUC as
their update client.
Signed-off-by: Martin Schwan <m.schwan@phytec.de>
Tested-by: Wadim Egorov <w.egorov@phytec.de>
The bootstd code itself does not have any dependency on BLK in order to
build. However, in order to minimize size growth of non-migrated
platforms, change this from being "default y" to "default y if BLK".
This will make it easier to begin migration of platforms which do not
have any BLK-class device but do want to use bootstd.
Signed-off-by: Tom Rini <trini@konsulko.com>
BOOTSTAGE_RECORD_COUNT=30 is too small to record booting a FIT image
with EFI kernel, initrd, dtb as seen on the StarFive VisionFive 2
board.
Increase the default for BOOTSTAGE_RECORD_COUNT to 50.
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@kernel.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
The option ONENAND_BOOT is never set, so remove it. The option
SYS_ONENAND_BOOT was never migrated to Kconfig and any platforms which
supported that have long been removed from the code, so remove the
reference there as well.
Signed-off-by: Tom Rini <trini@konsulko.com>
So far only VBE-simple is implemented in U-Boot. This supports a single
image which can be updated in situ.
It is often necessary to support two images (A and B) so that the board
is not bricked if the update is interrupted or is bad.
In some cases, a non-updatable recovery image is desirable, so that the
board can be returned to a known-good state in the event of a serious
failure.
Introduce ABrec which provides these features. It supports three
independent images and the logic to select the desired one on boot.
While we are here, fix a debug message to indicate the function it
called. Provide a maintainers entry for VBE.
Note that fwupdated only supports VBE-simple so far, but supports for
ABrec will appear in time.
Signed-off-by: Simon Glass <sjg@chromium.org>
VBE uses a crc8 checksum to verify that the nvdata is valid, so make
sure it is available if VBE is enabled.
Signed-off-by: Simon Glass <sjg@chromium.org>
With VBE we want to use FIT in all phases of the boot. Add Kconfig
options to support this.
Disable the options for sandbox_vpl for now.
Signed-off-by: Simon Glass <sjg@chromium.org>
This reverts commit 1fdf53ace1, reversing
changes made to e5aef1bbf1.
I had missed that this caused too much size growth on rcar3_salvator-x.
Signed-off-by: Tom Rini <trini@konsulko.com>
VBE uses a crc8 checksum to verify that the nvdata is valid, so make
sure it is available if VBE is enabled.
Signed-off-by: Simon Glass <sjg@chromium.org>
With VBE we want to use FIT in all phases of the boot. Add Kconfig
options to support this.
Disable the options for sandbox_vpl for now.
Signed-off-by: Simon Glass <sjg@chromium.org>
I enabled IMX_HAB on an imx8mp board, but even though I knew about the
implementation, I forgot that I had to provide a sane value for
SPL_LOAD_FIT_ADDRESS. The help text for IMX_HAB doesn't mention this
implicit requirement, and there's no build-time warning; the default
0x0 value just ends up being returned from
board_spl_fit_buffer_addr(), obviously resulting in a non-booting
board.
The existing imx8m* board configs that set a non-zero value currently
all use 0x44000000. The actual value doesn't matter too much, but 0 is
always wrong for imx8m platforms. So just use 0x44000000 as default
for those platforms.
Signed-off-by: Rasmus Villemoes <ravi@prevas.dk>
The bootflow_menu.c code depends on e.g. scene_txt_set_font(),
which is only built when CONFIG_EXPO is enabled. Introduce new
Kconfig symbol BOOTSTD_MENU which depends on EXPO to prevent
triggering errors like these in case e.g. CONFIG_VIDEO=n :
"
boot/bootflow_menu.c:158:(.text+0x8851): undefined reference to `scene_txt_set_font'
"
Make the symbol depend on BOOTSTD_FULL as well to get rid of
the Makefile dependency workaround. Since BOOTSTD_FULL is not
available in SPL, do not define SPL variant of BOOTSTD_MENU.
Fix up bootflow test accordingly.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
The fdt_simplefb.c APIs rely on video-uclass APIs and structures to
fill/update framebuffer information, so compile it only when VIDEO
Kconfig is enabled, as otherwise below warning can be seen if VIDEO
Kconfig is disabled:
"boot/fdt_simplefb.c:96:12: warning: fdt_simplefb_enable_existing_node
defined but not used [-Wunused-function]
96 | static int fdt_simplefb_enable_existing_node(void *blob)"
Reported-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Signed-off-by: Devarsh Thakkar <devarsht@ti.com>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
The SPL_FIT_SOURCE is long superseded by SPL_FIT_GENERATOR which
is long superseded by binman, drop SPL_FIT_SOURCE support as there
are no more users.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Peter Robinson <pbrobinson@gmail.com>
Prepare the introduction of the lwIP (lightweight IP) TCP/IP stack by
adding a new net/lwip/ directory and the NET_LWIP symbol. Network
support is either NO_NET, NET (legacy stack) or NET_LWIP. Subsequent
commits will introduce the lwIP code, re-work the NETDEVICE integration
and port some of the NET commands and features to lwIP.
SPL_NET cannot be enabled when NET_LWIP=y. SPL_NET pulls some symbols
that are part of NET (such as arp_init(), arp_timeout_check(),
arp_receive(), net_arp_wait_packet_ip()). lwIP support in SPL may be
added later.
Similarly, DFU_TFTP and FASTBOOT are not compatible with NET_LWIP
because of dependencies on net_loop(), tftp_timeout_ms,
tftp_timeout_count_max and other NET things. Let's add a dependency on
!NET_LWIP for now.
SANDBOX can select NET_LWIP but doing so will currently disable the eth
dm tests as well as the wget tests which have strong dependencies on the
NET code.
Other adjustments to Kconfig files are made to fix "unmet direct
dependencies detected" for USB_FUNCTION_SDP and CMD_FASTBOOT when
the default networking stack is set to NET_LWIP ("default NET_LWIP"
instead of "default NET" in Kconfig).
The networking stack is now a choice between NO_NET,
NET and NET_LWIP. Therefore '# CONFIG_NET is not set' should be
'CONFIG_NO_NET=y'. Adjust the defconfigs accordingly.
Signed-off-by: Jerome Forissier <jerome.forissier@linaro.org>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
:hile we had hoped to be able to remove these options finally, it was
missed that zynq still requires these currently.
This reverts commit 5b9261fb0b and
commit 099b6df556.
Reported-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Tom Rini <trini@konsulko.com>
The SPL_FIT_GENERATOR is long superseded by binman, drop SPL_FIT_GENERATOR
support as there are no more users.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The SPL_FIT_SOURCE is long superseded by SPL_FIT_GENERATOR which
is long superseded by binman, drop SPL_FIT_SOURCE support as there
are no more users.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Peter Robinson <pbrobinson@gmail.com>
The EFI_LOADER and EFI config options are randomly scattered under lib/
making it cumbersome to navigate and enable options, unless you really
know what you are doing. On top of that the existing options are in
random order instead of a logical one.
So let's move things around a bit and move them under boot/. Present a
generic UEFI entry where people can select Capsules, Protocols,
Services, and an option to compile U-Boot as an EFI for X86
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add the basic code to create a handoff structure in SPL, so it can be
passed to the next phase. For now this is not plumbed in.
Signed-off-by: Simon Glass <sjg@chromium.org>
Jonas Karlman